ADDN/ALTN TO WATCH TOWER NEAR BAFFLE RANGE SPECIAL REPAIRS TO COMPOUND WALL NEAR BLDG NO. P-200A AND PROVN OF TOILET BLOCK FOR 172 INF BN (TA) MADRAS AT BRICHGUNJ MIL STATION UNDER GE BRICHGUNJ PORTBLAIR

Amount

Surface dressing n exc 15 cm deep in soft/ Loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in soft / loose soil all as specified and directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in hard/dense Soil complete all as specified and as directed.

Excavating over areas, not exc 1.5 m deep for foundation, laying of cables etc., and getting out in hard/dense soil all as specified and as directed

Excavation over areas n.exc 1.5m deep and getting out hard / dense soil complete all as specified and as directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft / loose soil including making good of disturbed surfaces complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 Mtrs and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed.

Material and labour treating the bottom & sides of excavation @ the rate of 5 Lit of emulsion per square metre of surface area complete all as specified and as directed.

Material and labour for ATT on top of earth filling @ 5 lits/square metre complete all as specified and as directed.

Material and labour Broken Brick bats gauge 80 to 150mm Loose filling in soakage pits, soakage wells complete all as specified and as directed.

Material & Labour for Moorum/Red Bajri Filling in floors or pavings, laid in layers n exc 15cm thick, spread, levelled and rammed including watering and complete

Material and labour for hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface.

Material and labour Coarse aggregate (Kankar or Laterite) grading 1, 90 to 40 mm size complete all as specified and as directed..

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing the rubbish off the premises complete all as specified and as directed..

Demolition of precast concrete articles, built in cement mortar, disposal of unserviceable material, debris and rubbish to a distance n exc 100m as directed by the Engr-In-Charge.

Demolition of RCC in ground floors exc 15 cm thickness but above ground floors (reinforcement cut as required to facilitate demolition) incl disposal of debris and rubbish to a distance n exc 100m as directed by the Engr-In-Charge.

Material and labour Extra for forming fair finished channel or drain 30cm girth (inner girth) in cement concrete using extra cement incl form works, moulds stopped complete all as specified and as directed..

Material and labour for PCC 1:3:6 Type C2 (using 40 mm graded aggregate) as in bed to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and as directed.

Material and labour for 75 mm thick cement concrete (1:4:8) Type D2 (using 40 mm graded aggregate) as in sub-base of flooring complete all as specified and as directed.

Material and labour for 75mm thick PCC 1:3:6 Type C-2 (using 40 mm graded aggregate) as in plinth protection, ramp etc finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for Damp proof course to horizontal or vertical surfaces including necessary form work in 40 mm thick cement concrete 1:2:4 Type B-0 (using 12.5 mm graded aggregate) with applying evenly a coat of blown Type bitumen at the rate of 1.50 kilogram per square meter and blinding with clean dry sand @ 0.05 cubic metre per square metre complete all as specified and as directed.

Material and labour for 80mm thick PCC(1:2:4) Type B2 using 20mm graded stone aggregate as in flooring finished even and smooth using extra cement complete all as specified and as directed.

Material and labour for 100 mm thick PCC 1:3:6 Type C2 using 40mm graded stone aggregate as in sub base of floors complete all as specified and as directed.

Material and labour Plain Cement Concrete 1:4:8 Type D2 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour for PCC 1:3:6 Type C2 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour for PCC 1:2:4 Type B1 (using 20 mm graded granite stone aggregate) as in coping surface channels, benching etc of manholes finished fair and even complete all as specified and as directed.

Material and labour for precast cement concrete solid block masonry with solid blocks using PCC 1:3:6 Type C1 using 20mm graded stone aggregate n.exc 10cm in width and setting in cement mortar (1:4) etc complete all as specified.

Material and labour precast cement concrete block masonry with PCC solid blocks in 1:3:6 Type C1 using 20mm graded stone aggregates, exc. 10cm in width and set in CM 1:4 complete all as specified and directed.

Material and labour Precast cement concrete 1:3:6 Type C1 (using 20mm graded stone aggregate) as in block masonry with solid bocks, exc 10cm width and set in cement mortar 1:6 compete all as specified and directed.

Material and labour Precast cement concrete hollow block masonry 1:2:4 Type (using 16 mm graded stone aggregate) as in block masonry with Hollow bocks, 10cm Thick and set in cement mortar 1:6 compete all as specified and directed.

Material and labour for precast RCC (1:2:4) Type B1 (using 20mm graded stone aggregate) as in cover slab for manholes, septic tank and similar work including formwork set in CM (1:6) all as specified incl necessary form work and placed in position all as directed.

Material and labour for Reinforced cement concrete M30 (design mix) in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified.

Material and labour for Reinforced cement concrete M30 (design mix) in Beams, cantilevers, bressumers, lintels over 1.5m span, complete all as specified.

Material and labour for Reinforced cement concrete M30 (design mix) in Chajjas complete all as specified.

Material and labour for RCC M-30 design mix 20mm graded stone aggregateas in columns, pillars, etc complete all as specified and as directed.

Material and labour for form work to sides of rough finished concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits if any of foundation and plinth beams and similar work vertical or to batter complete all as specified and as directed by Engineer in Charge.

Use and waste form work to sides and soffits of rough finished floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc also splays between floors, and beams, etc complete all as specified and as directed by Engineer in Charge.

Use and waste form work of sides of pillars, posts struts, piers, column and stanchions square/rectangular rough finished surface of concrete complete all as specified and as directed.

Use and waste form work to chullah hoods, chajjas, troughs and similar items including edges, etc complete all as specified and as directed by Engineer in Charge

Material and labour for TMT bars 10mm dia and over as in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing clips

Material and labour mild steel TMT Bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Material and labour for TMT bars 5mm dia and over upto and incl 10mm dia in stirrups, spacers, and binders in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire.

Supply only water proofing compound conforming to IS-2645 1975 complete all as specified and as directed.

Material and labour for rendering 10mm thick on fair faces of brick/concrete surface in CM (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for Rendering 15mm thick on fair faces of brickwork/concrete surfaces in cm 1:6 is to be finished even and smooth, surfaces without using extra cement complete all as specified and as directed.

Material and labour for 15mm thick external rendering in two layers of 5mm thick in CM 1:4 mixed with water proofing compound (water proofing compound shall be used @ 3% by weight of cement) over a coat of 10mm thick in CM (1:6) over brick or concrete surfaces finished even and fair. Note: Supply only WPC will be measured and paid separately

Material and labour for 10mm thick rendering in CM 1:4 mixed with water proofing compound (water proofing compound shall be used @ 3% by weight of cement) over brick or concrete surfaces finished even and fair. Note: Supply only WPC will be measured and paid separately

Material and labour Rendering 15mm thick on brick/stone or concrete surfaces in cement Mortar 1:6 finished fair and even without using extra cement complete all as specified and as directed.

Material and labour Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 using water proofing compound @ 3% by weight of cement for finished even and smooth without using extra cement. Note: Supply only WPC will be measured and paid separately

Material and labour for 15 mm thick rendering in CM 1:4 on concrete surfaces finished fair and even complete all as specified and as directed.

Material and labour 10mm thick rendering in cement plaster 1:4 on fair faces of brick or concrete surface, and finishing the surface even and smooth w/o using extra cement etc complete all as specified and as directed.

Material and labour applying two coat of cement base paint over a coat of white wash on new plastered or untreated surface of wall including preparation of wall surfaces all as directed and specified

Material and labour for oil bound distempering two coats over a coat of alkali resistant priming paint including preparation of new plastered or unplastered surfaces of wall complete all as specified and directed by Engineer - in -Charge.

Material and labour for two coats of synthetic enamel painting over a coat of red oxide zinc chrome primer incl preparation of new or previously untreated steel surfaces of any description over 10cm width or girth complete all as specified and as directed.

Material and labour for two coat of weather proof exterior acrylic emulsion paint with anti-fungal property over a coat of primer on newly plastered wall surfaces including preparation of surfaces etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for applying two coats of exterior emulsion over a coat of alkali resistant primer incl preparation of old plastered surfaces complete all as specified and as directed.

Material and labour for applying three coats white washing on newly plastered surfaces of wall including preparation of surfaces by complete all as specified and as directed

Supply and fix plates (Plain or chequered), channels, square cut or notched (ordinary and counter sunk) forming holes with attachment etc and fixed by riveting or welding or with nut and bolts (including nut and bolts) conforming to Fe- 410-W Grade E- 250, quality B, complete all as specified and as directed.

Supply and fix MS Steel work in tubular trusses and tubular posts/ purlins including special shaped washers etc., complete using ERW or induction butt welded tubes conforming to IS :1161-1979 grade st-240 including notching, drilling, fitting, riveting and/or welding or connecting with bed plate, bolt and nuts complete all as specified and as directed

Supply and fix Mild steel bolts exc 12mm n. exc 20mm dia, purpose made, with hexagonal or square head one end and screwed the other, or screw both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long complete all as specified and as directed.

Material and labour for MS work such as rung, handles to manholes, etc. complete all as specified and as directed.

Supply and fix prepainted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in ridges, roof covering/cladding to wall fixed with self-tapping screws all as specified and directed.

Supply and fix pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self-tapping screws etc complete all as specified and as directed.

M&L for false ceiling with aluminium grid work (size of grid 605x605mm) with 35x25x1.5mm main tee and 25x25x1.4mm, cross tee and wall angle and suspended with 3.15mm dia, GI wire, hooked to roof with needful adjustment bolts at an interval of 1.20m, centre to centre staggered and board with Eco board, decorative type, size 600x600x4mm thick, finished with two coats of oil bound distemper over a coat of primer complete all as specified and as directed by Engineer-in-Charge.

Material and labour glazed ceramic coloured tiles in vertical surface 300 mm x 200 mm x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles with 10mm thick rendering even and rough finished on brick wall in cement mortar 1:3 all as directed by Engr-in Charge

Material and labour Glazed ceramic tiles coloured 350x 250x5/ 450X 350X 7mm thick on vertical surfaces such as skirting, dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick in CM 1:3 as backing coat for fixing dado tiles all as specified and as directed

Material and labour Non-skid ceramic tiles each tile area (sqr/rectangle) exc 0.06square metre but not exceeding 0.11square metre tile thickness 7 to 8 mm, in floors etc set and joined in neat cement slurry and pointed in white or coloured cement to match incl Screed bed or bedding layer of 20mm thick with CM 1:6 for laying floor finishes all as specified .

Material and labour non-skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 square metre and not exceeding 0.38 square metre in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles over 20mm thick screed bed in CM 1:6 all as specified and as directed

All as per item No 68 here in before, but on vertical surfaces incl 10mm thick CM 1:3 as in baking coat of dado/skirting

Material and labour glazed polished finished chequerred cement concrete tiles 300x300mm x 25mm thick size set, jointed and pointed in neat cement slurry incl 20mm thick in CM 1:6 bedding layer of cement mortar all as specified and as directed

Supply and fix Aluminium powder coated (minimum 50microns coating thickness) frames (for parapet railing) incl fixing to walls/RCC pillars by jambing, necessary joining cleats for frames, screws, etc., complete with standard aluminium sections, complete all as specified and as directed by Engineer-in-charge.(Aluminium section shall be of make Jindal/Hindalco/ Indalco).(Note:- Weight of various Aluminium sections handles and locking arrangements shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, aluminium wire cloth as applicable will be measured and paid separately as supplied only).

Material and labour for Aluminium anodised (minimum anodisation is 15 microns) Door / window / Ventilator/partition frames and shutters sliding shutter as on aluminium tracks using standard aluminium anodised sections including necessary joining cleats, glazing clips, rubber packing anodised aluminum snap beading, screws, anodised aluminium fittings etc., complete of standard sections all as specified and directed. (Aluminium section shall be of make Jindal/Hindalco/ Indalco). Note:- Weight of Aluminium sections for frames and shutters shall only be considered for measurement for payment. However cost of other consumables given in the items shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle board and aluminium wire mesh as applicable will be measured and paid separately as supplied only.

Supply and fix 2nd class Hard wood 15mm thick plain both side as in eaves board etc. complete all as specified and as directed.

Supply and fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

Supply and fix Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

Supply and fix Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips of sheet cast or extruded sections and fixing bolt or cast aluminium alloy& fixed complete all as specified and as directed.te .

Supply only 4.0mm thick Sheet glass ordinary quality and glazing with oil putty in Square exc 0.5square metre in each pane complete all as specified and as directed.

Supply only 4.0mm thick frosted sheet glass ordinary quality and glazing with oil putty in Square n.exc 0.5square metre in each pane complete all as specified and as directed.

Supply only 4 mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares not exceeding 0.50 square metre in each pane complete all as specified and as directed by Engineer-in-Charge.

Supply only 12mm thick pre-laminated particle board, exterior grade, lamination on one side with decorative choice lamination and the other side balancing white lamination fixed with screws as in door panel, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 4 mm thick sheet figured glass and glazing with rubber packing around the glass, in squares exceeding 0.50 square metre in each pane complete all as specified and as directed.

Supply only 4 mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares exceeding 0.50 square metre in each pane complete all as specified and as directed by Engineer-in-Charge.

Supply only Aluminium alloy wire cloth,0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, etc complete all as spd and directed.

Supply and fix Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete all as specified and as directed.

Supply and fix 150mm long extruded aluminium alloy anodised handles fabricated type complete all as specified and as directed.

Supply and fix Butt hinges extruded Aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type C-21. with MS hinge pin 100 mm size complete all as specified and as directed.

Supply and fix Chromium plated tubular towel rail complete all as specified and as directed.

Supply and fix of PTMT gratings 125mm dia, complete all as specified and as directed by Engineer-in-Charge

Supply and fix of PVC connection 15mm size with CP brass Nuts of length 450mm complete all as specified and as directed by Engineer-in-Charge

Supply and fix 75 mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

Supply and fix Chromium plated 125mm shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed.

Supply and fix Towel rail 600mm long & including Chromium plated brass screws & wooden / plastic cleats (Minimum weight 190gms)

Supply and fix of stop valves cast copper alloy, screwed down, high pressure, with fancy type, chromium plated, screw both ends for 15mm dia iron pipe or for union and fixed.

Supply and fix of brass, chromium plated toilet paper holder fixed to walls with chromium plated brass screws complete all as specified and as directed.

Supply and fix PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

Supply and fix waste fittings 32 mm bore, brass, chromium plated for basins etc with long screwed shanks and fly nuts, flange and bed deal in red lead cement and other end complete all as specified and as directed.

Supply and fix 100mm cast iron sanitary connections-short connections pipe of length upto 300mm complete all as specified and as directed.

Supply and fix for PVC (SWR) vent cowl, bore of pipe in 110 mm, etc complete all as specified and directed.

Supply and fix for PVC (SWR) vent cowl, bore of pipe in 75 mm, etc complete all as specified and directed.

Supply and fix PVC (SWR) bends any radius 110mm bore complete all as specified and directed.

Supply and fix Soap dish, vitreous China white, approximate size 160x160x90mm complete all as specified and as directed.

Supply and fix in repairs chromium plated hand shower (health faucet) 1 meter, with PVC tube with wall hook , complete all as specified and as directed by Engineer-in-Charge. (Make : Jaquar cat No ALD-CHR-593)

Supply and fix in repair Vitreous China wash basin, white, flat back, size 550x400 mm including brackets, waste coupling brass CP 32mm bore with long screwed shanks and fly nuts, pillar tap cast copper alloy chromium plated fancy type with long screwed shanks and fly nuts screwed for iron pipes etc. complete.

Supply and fix in repairs wash hand basin of size 375X475X130mm including all fittings and bracket etc of Jaquar Cat No. JDS-WHT-25907 complete all as specified.

Supply and fix in repairs vitreous china wash down water closet (pedestal pan) white, including 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC 32mm dia, Plastic water closet seat, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hanging device, complete all as specified and as directed.

Supply and fix in repair Vitreous China urinal half stall, white, including providing fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around and back in cement etc. complete all as specified and directed.

Supply and fix of 10 ltr capacity, PVC flushing cistern, white, syphonic action type, low level, with in let, ball valve float and handle, PVC flush pipe, brackets etc including taking down unserviceable flushing cistern etc, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Vitreous China squatting pan, Orissa pattern size 580x440mm white, including 10 Ltrs PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, flush pipe of polyethylene 32mm dia, for low level cistern etc. complete.

Supply and fix in repairs water closet pan (pedestal pattern) white, os size 650X360X800mm of Jaquar Cat. No. OPS-WHT-15751 and with flushing Cistern & fittings of Jaquar Cat.No. ZPS-WHT-15201 complete all as specified

Supply and fix Swivel shower of PTMT any colour for fixing with 15mm pipe (Minimum weight 40gms) fixed with A shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour complete all as specified and directed. (Note:-Minimum weight 40 gms)

Supply and fix 15mm bore Stop/ Angle valve, cast copper alloy, chromium plated fancy type screwed down, screwed for iron pipe and fixed.

Supply and fix 20mm dia ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, minimum weight 142 gms, complete all as specified and directed by Engineer-in-Charge

Material and labour for bib tap cast copper alloy with crunch or butterfly handle , screwed down, screwed for iron pipe or brass ferrule fancy type chromium plated bore of pipe 15 mm complete all as specified and directed.

Supply and fix of Bib tap cast copper alloy chromium plated 15mm dia with fancy type screwed down screwed for iron pipe or brass ferule etc complete all as specified and as directed by Engineer-in-Charge

Supply and fix CP pillar tap 15 mm bore with capstan head, screwed reed down high pressure with or without lettered 'hot' or 'cold' with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

Supply and fix 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and as directed

Material and Lobour for 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Supply and fix 75 mm bore PVC (SWR) bend any radius complete all as specified and directed.

Supply and fix rotational moulded polyethylene water storage tanks 1000 ltrs capacity (cylindrical or vertical with closed top) hoisted and fixed in position, complete all as specified and directed by Engineer-in-Charge

Supply and fix Rotational moulded polyethylene water storage tanks of capacity 500 Ltr (cylindrical vertical with closed top) with 20mm dia float valve , hoisted and fixed in position all as specified in SSR Part I

Material and labour for 15 mm bore unplasticised PVC pipes of pressure rating 10 kgf/Sqcm fixed complete to walls, ceilings or in floors etc any type of pipe all as specified and as directed.

Material and labour for 20 mm bore unplasticised PVC pipes of pressure rating 10 kgf/Sqcm fixed complete to walls, ceilings or in floors etc any type of pipe all as specified and as directed.

Supplying and laying of CPVC pipes of outer dia 16mm SDR 11 and plain CPVC SDR 11 with all fittings complete in trenches all as specified

Supplying and laying of CPVC pipes of outer dia 20 mm SDR 11 and plain CPVC SDR 11 with all fittings complete in trenches all as specified

Supplying and laying of CPVC pipes of outer dia 25mm SDR 11 and plain CPVC SDR 11 with all fittings complete in trenches all as specified

Supply and fix for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in any position or in floors, bore of pipe in 75 mm, etc complete all as specified and directed.

Material and labour for 150mm dia CI pipe (sand cast) in any length with (or) without ear laid in trenches and jointed in CM 1:1 complete all as specified and directed.

Supply and fix 25 mm bore GI tubing medium grade laid in trenches / floor or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed

Supply and fix 50 mm bore GI tubing light grade laid in trenches with fitting for laying cables complete all as specified and directed

Material and labour for cutting existing 40mm GI line and making branch connection of 25 mm dia GI line complete all as specified and directed.

Material and labour for cutting existing 50mm GI line and making branch connection of 40 mm dia GI line complete all as specified and directed

Supply and fix for 20 mm dia bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe fixed complete all as specified and directed.

Supply and fix 25 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specified and directed

Material and Labour for cutting bituminous road at a width not more than 30cm and a depth not exceeding 60 cm for laying of pipes on road crossing for cable protection and making good with cement concrete 1:2:4, Type, B-2 (using 40mm aggregates) to match the existing surfaces of the road all as specified and as directed by Engineer in charge.

Material and labour Point wiring complete with 1.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC casing and caping and all accessories fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover/Pre moulded PVC switch board for housing the switches, socket outlets, fan regulators etc. for One light point controlled by one way switch all as specified and as directed.

All as per item No 136 here in before but for One fan point controlled by one switch and one regulator

all as per item No 136 here in before but for One 3 pin switch socket outlet point 5 amps on independent board.

Material and labour For Point wiring complete with proper colour coding using, 1100 Volts grade, 1.5 sqmm, PVC insulated FRLS, unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked and including PVC non-metallic rigid conduit with ISI marked with all accessories concealed in wall/celling/floor/roof etc, sunk pressed steel not less than 2 mm thick, 50 mm deep terminal boxes with 3mm thick ISI marked plastic laminated sheet top cover fastened with chromium plated brass screws including 1.5 sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts Multistranded copper conductor green colour as continuous earth wire connected to common earth dolly for One light/Exhaust fan point controlled by one switch all as specified and directed

Supply and fixing in replacement of switch piano flush type single pole one way 5 Amp all as specified and directed.

Supply and fix switch socket outlet 3 & 2 pin (mult pin) 5 amps flush/box type, complete all as specified and as directed by Engineer-in-Charge

Supply and fix ceiling rose surface Bakelite 65 x 50 mm 3 terminal, complete all as specified and as directed by Engineer-in-Charge

Supply and fixing energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core sheathed cable from fitting to ceiling rose all as specified and as directed. Make : Philips Cat No BN021C LED20S PSU CDL/NW GR or eqvt in make of Bajaj/Wipro.

Supply and fix ceiling fan suitable for working on AC 230 volts, 50 Hz,1200 mm sweep 5 star rating with down rod and canopy colour of milky white including suitable fan hook anchor flasher for fixing of fan on ceiling complete all as specified and as directed. Make:Havells or equivalent Crompton/Usha

Supply and fix metal enclosure distribution board SPN, 4 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, including taking down old MCB/DB, complete all as as specified and as directed by Engineer-in-Charge. Make:Legrand/C&S/L&T Note:- Incoming & Outgoing connections from the DB shall be provided with proper lugs/thimbles etc...

Supply and fix MCB single pole 240 volts, 0.5 to 32 amps complete all as specified and as directed by Engineer-in-Charge Make : Legrand/C&S/L&T

Supply and fix MCB SPN, 240 volts, 6 to 32 amps C series complete all as specified and as directed by Engineer-in-Charge Make : Legrand/C&S/L&T

Material and labour for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts, check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I

Supply and fixing energy efficient LED Smart bright batten 10 watt fitting 2ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 25000 hours including lamp and connecting with twin core sheathed cable from fitting to ceiling rose all as specified and as directed. Make : Philips Cat No BN021C LED10S -6500 PSU GR S1 or eqvt in make of Bajaj/Crompton.

Supply and fix Street light New generation energy saving & environmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs 25 w as light and electronic driver complete all as per Philips Cat No BRP020 LED HP/ CW 240 v or equivalent model of Wipro / Bajaj/Crompton with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete as directed.

Supply and fix exhaust fan suitable for on working of AC 230 V ,50 Hz 300 mm sweep 1400 RPM, with heavy duty motor, including louvers complete all as specified and as directed. Make: Havells/Crompton/Orient

Supply, lay, test and commissioning underground XLPE insulated and PVC sheathed, armoured heavy duty underground cable, 1100 volt grade of cross section area 2 Core 6 sq mm suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor complete all as specified and as directed.

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers, bends etc of size 50 mm OD and 38mm ID confirming to IS 14930 -II and ISI Marked all specified and directed.

B S Grewal

Hindustan Traders

T.THIYAGARAJAN

Ravi Enterprises