REPAIRS TO DOORS, WINDOWS, VENTILATORS, CUPBOARDS AND OTHER RELATED B/R WORKS IN AREA-II UNDER AGE B/R-II AT GE KAMPTEE.

Amount

Taking down door / window frame with shutter (without taking off shutter from the frame) area not exc 1.5 sqm complete all as specified and directed.

Taking down door / window frame with shutter (without taking off shutter from the frame) area exc 1.50 sqm but not exc 4 sqm complete all as specified and directed.

Taking down shutters only of any description area not exc 1.00 sqm each complete all as specified and directed.

Taking down shutters only of any description area exc 1.00 sqm but not exc 2.00 sqm complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for in any position complete all as specified and directed.

Dismantling of timber fillets, rails, posts, rafters, purlins under 40 Sq cm in section complete all as specified and directed.

M&L for second class hard wood plain fillets square in section, clean sawn, secured with nails, size exc 6 sqcm but not exc 13 sqcm complete all as specified and directed.

M&L for mild steel framed work of Fe-290 (Gde E-165) as in doors or gates of angle or other section with gusset plates, rails, braces, MS Plates etc., complete drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing etc complete all as specified and directed.

S&F 1.00mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe.290.Gde-E-165 etc complete all as specified and directed.

S&F second class hard wood 35mm thick factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 30mm thick flush shutters solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and directed.

S&F 30mm thick 2nd class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), kiln seasoned and chemically pressure treated complete all as specified and as directed.

All as per item No 13 above but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers for windows, ventilators etc, as specified in SSR part-I, Sec-08, Clause 8.24(b), complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, & fixing in opening complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2mm thick moulded prelam PVC sheet on the front face & 2mm prelam colour PVC sheet on back face, with wood free EPS, & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 100mm long mild steel butt hinges, medium weight, cold rolled and fixed with screw/ welded to frames etc complete all as specified and directed.

All as per item No 17 above but 75mm long complete all as specified and as directed.

S&F 125mm extruded aluminium handles, fabricated type, anodised etc complete all as specified and directed.

All as per item No 19 above but 100mm long complete all as specified and as directed.

S&F 150mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and directed.

All as per item No 21 above but 100mm long complete all as specified and as directed.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and directed.

S&F steel windows with side hung shutters including butt type hinges with steel handle, and steel peg stay, complete with glazing and gauzing bars, dovetailed or welded complete all as specified and directed.

All as per item No 24 above but without glazing bars complete all as specified and as directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F ECO-4000 series pre-coated double rebated openable windows or ventilator made out of galvanised steel colour coated/ powder coated (base steel as per IS 513 of 'D' quality galvanised as per IS 277 with zinc of 120gm/Sqm) with total thickness of coating 0.58 microns finished painted with polyster paint 12-16mm microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with polyster powder upto 50-60 microns thick outer frame section 72x55mm, centre mullion section 72x50mm, shutter section 47 x 20mm, fly mesh section 40x20mm and the fxed glass beading section 12x12mm outer frame and mullions shall consists rebate for glazed shutter, fly mesh and 20mm provn for guard bars/grills, the section cut to length miter joints with corner brackets, centre mullions fixed with mullion cap, stay handles, latch 2 Nos of heavy duty stainless steel pivot hinges per shutter and panelled with 5mm thick plain float glass and stainless steel(304 grade) mesh for fly mesh shutter fixed with EPDM gasket incl fixing windows with concrete/ stone or brick masonry wall by means of self expanding sleeves and driving MS electroplated 80mm long bolt into the sleeve through frame (minimum 4 Nos fro 1600 mm high windows, 3 nos for 1200mm or less windows and 2 Nos in ventilators), incl 10 mm Square bars welded to 6 x 12mm flat at a distance 125mm c/c etc complete all as specified and directed. Make:- SECCOLAR of NCL ALLTEK & SECCOLAR Ltd, Hyderabad and M/s Ashwani & Sons, Ghaziabad.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

Supply, fabrication and fixing anodised aluminium doors fixed or openable including frame/chowkats etc from hollow rectangular sections like chowkats of size 100 x 44mm x 1.59mm (appx), vertical styles of size 82 x 44 x 159mm (appx) top and middle rails of size 82 x 44 x 1.59mm (appx) bottom rails of size 114 x 44 x 1.59mm (appx) complete including necessary jointing cleats, glazing clips, anodised aluminium beading and rubber gasket etc for securing glass, anodised aluminium fittings such as handles, other standard fittings, aluminium tower bolts - 2 Nos, Hydraulic Door closer of designation No-3 - 01 No and accessories for locking arrangements etc complete all as specified and directed. Note:- Glazing shall be measured and paid for separately under respective items complete all as specified and directed.

Supply, Fabrication and fixing anodised aluminium windows, ventilators, shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber gasket, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21, 100mm long (2 No) suitable handle (1 No) complete all as specified and directed. Note:- Glazing/gauzing shall be measured and paid for separately under respective items.

S&F in repairs 5.5mm thick tinted sheet glass ordinary quality and glazing with Al glazing clips & EPDM beading in square exc 0.5 sqm in each pane complete all as specified and directed.

S&F in repairs 18mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination other side balancing white lamination, fixed with screws to timber frame work / mild steel framing/ 6mm thick first class H/W leaping on bare edges complete all as specified and directed.

S&F continuous (piano) hinges, 30mm wide flap mild steel, bright finish or electrogalvanised complete all as specified and directed.

Taking down cup board drawers and refixing the same after necessary repairs incuding replacement of both telescopic sliding channels of size 53cm (21 inch) best quality as approved by Engr-in-Charge complete all as specified and directed.

Taking down steel window/ ventilators shutter of any size & description and refixing the same opening after minor repairs / weldings including providing box type hinges- 02 Nos at each leaf & necessary small assesories as required complete all as specified and directed.

Taking down aluminium door shutters and refixing the same after re-setting of all aluminium sections including cleats, beadings and panels complete all as specified and directed.

S&F galvanised steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F in repairs galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm as in gauze door /window/ ventilators shutters including necessary wooden/ steel beading complete all as specified and directed.

Hacking out old broken glass (any thickness size and quality and description) from wooden/ steel frames glazed with putty or fixed with beads etc complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality, not exc 0.50 sqm each pane and fixed with oil putty or with wooden beading in squares etc complete all as specified and directed.

S&F in repairs 12mm thick sheet glass, ordinary quality, any shape and size and fixed complete all as specified and directed.

S&F in repairs door closer hydraulically regulated universal type, sutiable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg of extruded aluminium section, designation No-3 complete all as specified and directed.

S&F in repairs double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty & fixed as in repair and including taking down old shutter and refixing in same opening after replacing floor spring complete all as specified and directed.

S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate, fixed with screws or welded complete all as specified and directed.

S&F in repairs 125mm aluminium anodised hasp and staple, safety type, hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F in repairs 20mm dia stainless steel curtain rod of approved quality including cutting and fixing to curtain brackets complete all as specified and directed.

S&F fancy type curtain brackets of approved quality, fixed to wall with screws complete all as specified and directed.

S&F in repairs 150mm extruded aluminium handles, fabricated type, anodised etc complete all as specified and directed.

S&F in repairs 100mm extruded aluminium handles, fabricated type, anodised etc complete all as specified and directed.

S&F in repairs 150mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F in repairs 125mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F in repairs 100mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F in repairs 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy and fixed complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not otherwise described, exc 10cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of untreated new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and as directed.

S&F in repairs floor door stopper of 140mm aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F wire brush with aluminium section 20mm x 1mm and brooms to fill the gap of floor and door shutter complete all as specified and directed.

S&F in repairs solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site with necessary L&T PVC beading on PVC frame as per specifications complete all as specified and directed.

Cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10cm girth in cement mortar 1:3 complete all as specified and directed.

Dismantling asbestos cement (Corrugated, semi corrugated etc.) of any thickness including ridges, hips, valleys as in roof covering/ sun sheds complete all as specified and directed.

M&L for 0.50mm thick prepainted galvalume aluminium zinc coating G.I. based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering, fixed with and including self tapping screws as per manufacturer's instructions complete all as specified and directed.

M&L for 0.50mm thick prepainted galvalume aluminium zinc coating G.I. based plain steel sheet of any colour having tensile strength of 550 Mpa as in ridges/ valley, fixed with and including self tapping screw as per manufacturer's instructions complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/ slabs/ blankets of any thickness and wall paneling including cover fillets complete all as specified and directed.

M&L for GI powder coated snap grid framework for false ceiling comprising of the following section for making partition of 600 x 600mm size fixed to wall with rawl plug and screw and hanged to roof with 4mm dia GI suspended wire of suitable length and butterfly clip of size of main Tee shall be 32mm x 24mm x 0.30mm, cross tee shall be 28mm x 24mm x 0.30mm thick with black lining in mid portion and wall angle shall be 24mm x 24mm x 0.30mm thick complete all as specified and directed.

M&L for 4mm thick non asbestos, fibre cement building board of size 595 x 595mm size in ceiling fixed or laid/ inserted to timber/ GI/ Aluminium framework with screws complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with fly ash bricks, old size, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

All as per item No 67 above but half brick thick wall in CM 1:4 complete all as specified and directed.

NOTE:- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs.45,560.00]

MVN Enterprises

M/s M.G. Hargunani

Bidder Name

MVN Enterprises

M/s B S Jain

M/s M.G. Hargunani