REPAIR/REPLACEMENT OF SPARES FOR MECHANICAL LAUNDRY EQUIPMENT, OXYGEN MANIFOLD SYSTEM, INCINERATOR EQUIPMENT, OTHER MISCLLANEOUS WORKS AT MH SECUNDERABAD AND REPAIRS TO THE E/M INSTALLATIONS OF B/R NATURE IN THE AREA OF AGE E/M NO II UNDER GE (U) SEC

Amount

M&L for spray painting of 100kg capacity Washing machines at laundry plant MH (incluing inner and outer surface areas and motors also, except stainless steel part/electric panels/belts etc) by apply two coats of metal primer and painting with two coats synthetic enamel paint of existing colour after removing all dust & rust and paint by scrapping with scrapping material shall confirm to IS 2032 including marking of SM/MES Number for each washing machine with stencil letter with black or white paint and Font and Size of letter and white washing for PCC based plinth shall be directed by Engr-in-Charge.

ditto- all as per item no.1 but for 50kg washing macines

ditto- all as per item no.1 but for drying tumbler at laundry plant MH all as directed by Engr-in-Charge.

Supply & Fixing following spare parts suitable to Drying Tumbler of capacity 50Kg including taking down old unserviceable spare parts complete all as specified and directed for Make of dry tumbler: Supershine

Digital Tempreature meter

Timer

Auxillary contacts

Contactor relay M L 1, 3 phase 415 volts

Contactor relay M L 2, 3 phase 415 volts

Auxilary relay

Revenger (Reverse Forward)

Main Motor -V-belt

Motor bearings

Blower bearings

Reduction gear bearings

Main bearing

Solenoid valve

Push button

Steam strap 15mm

Door Locks

Door Beading

Exhaust Fan/Blower

1/2" Steam Valve

3/4" Steam Valve

Reduction gear V-belt

Brake actuator

Supply & Fixing following spare parts suitable to Hydro Extractor of capacity 25Kg including taking down old unserviceable spare parts complete all as specified and directed for Make of Hydro extractor :Supershine

Contactor M L 1, 3 phase, 415 volts

Timer relay

Transformer

Timer

Buffer

Limit switch

Main motor bearings

Push button

Motor to body springs

Rubber bush for Hydro Extractor

Hydro Extractor motor bearings

Bridge rectifier

Diode

Body Spring support Bolts

Supply & Fixing following spares suitable to Washing machine 50Kg, including taking down old unserviceable spare parts complete all as specified and directed for Make of wahing machine: Supershine

Digital Tempreature meter

Timer

Contactor relay M L 1, 3 phase, 415 volts

Contactor relay M L 2, 3 phase, 415 volts

Relay M L 1, 3 phase, 415 volts

Relay M L 2, 3 phase, 415 volts

Revenger (Reverse Forward)

Water Level Indicator

Steam solenoid Valve

Drain valve actuator

Main motor V-belt

Aux Motor V-belt

Washing Machine main bearing

Reduction gear bearing

Water inlet solenoid valve suitable for 50 kg washing machine

Water outlet solenoid valve suitable for 50 kg washing machine

Gland rope

Main motor bearings

Aux Motor bearings

Toggle swtich

Supply & Fixing following spare parts suitable to Boiler of capacity 600Kg/Hr including taking down old unserviceable spare parts complete all as specified and directed for Make of boiler: Thermax

Gland Washer (HTN-8)

Valve seat Assembly

Metalic Hose 3/8" x 40"

Oil Seal (HTN-5)

Oil Seal (HCA-7)

Ball Bearings (HCA-5)

Pressure Switch PVF 1.0

Pressure Switch PVF 16

Metallic Hose 1" x 1.2m

Limit Switch

Photocell 8205

Sequence controller MA 810

Solinoid Coil

Electrode Assembly

Electrode Cap

High Tension Wire

Packing Hylam

Packing Asbestos

Gland Nut (HTN-6)

Oil Level Indicator

Sight glass 50mm

Ignition Transformer 14.5 KV

Temperature Controller 0-400V

RTD Assembly 2.5 mtrs

Safety valve 25mm

Plug & Socket

Hooter 4" Dia

Lip Seal

Spider for love joy couple

Burner rod Without nozzle

Fuel Pump

Diffuser Plate 132mm dia

Nozzle 6.5 GPH, 45 Degree

Diesel line Y strainer 25mm dia

Diesel line globe Valve 25mm dia

Steam line Y strainer 25mm Dia

Steam line Globe valve 25mm Dia

Steam line Y strainer 40mm Dia

Supply & Fixing following spare parts suitable to flat Bed press including taking down old unserviceable spare parts complete all as specified and directed for Make of flat bed press : Supershine

Steam Hose pipe 4 feet

Solenoid valve (pneumatic)

Air regulator

Contactor ML 1, 3 Phase, 415 Volts.

Digital temperature Meter

Digital timer

Pneumatic piston

Teflon foam

Heat proof cloth

Spring set

Steam traps 15mm dia

Supply & Fixing following spares suitable to Washing machine 100Kg including taking down old unserviceable spare parts complete all as specified and directed for Make of washing machines: Supershine & Megha laundry

Digital tempreature meter

Timer

Contactors ML 1, 3 Phase, 415 Volts

Contactors ML 2, 3 Phase, 415 Volts

Contactor relay M L 1, 3 phase, 415 volts

Revenger (Reverse Forward)

Water Level Indicator

Steam solenoid valve

Drain valve actuator

Main motor V-belt

Aux motor V-belt

Washing Machine main bearing

Reduction gear bearing

Indicator

Water inlet solenoid valve suitable for 100 kg washing machine

Water outlet solenoid valve suitable for 100 kg washing machine

Gland rope

Door Lock Knobs

Steam Valve (Globe)

Main motor bearings

Aux motor bearings

Toggle swtich

Supply & Fixing following spare parts suitable to Air Compressor of capacity 5HP including taking down old unserviceable spare parts complete all as specified and directed.

Limit switch

Motor bearings

Compressor Bearings

Piston Kit

Supply only following items all as specified and directed.

Wax (Candle Powder)

Grease (Castrol Make)

Chemical salt

PPM Testing Liquid Set

Laundrex softener chemical

Laundrex Det

Laundrex boost

Laundrex neutral

Meghana Liquid Bleach

Supply & Fixing following spare parts suitable to Slucing machine 7 Kg including taking down old unserviceable spare parts complete all as specified and directed for Make of slucing machine : Supershine

Controller

Timer

Motor V-Belt

Bearings

Steam Solenoid valve

Main Bearing

Manual Timers

Indicators

Supply & Fixing spare parts suitable to calender Machines including taking down old unserviceable spare parts complete all as specified and directed for Make of calender machines: Supershine & Megha laundry Eqpts

Variable frequency drive

Padding cloth

Blower Motor Rewinding

Temperature Meter

Speed Regulator

Push buttons (Red, Green,Blue)

NO-Element

NC-Element

Toggle Switch

Steam Solenoid Coil 15 mm

FLR Unit

Steam inlet Braided hose pipe 1" x 2 ft

Pneumatic cylinders servicing only except spares

Wax for cleaning chest

Guide Ribbons

Painting for feeding plate

Grease for chain and gear wheel teeth

Steam trap servicing

Air line and steam line with all connectors

Lubrication oil and gear oil

Steam line Y strainer 25mm dia

Disconnecting of Motor from washing machine/ Hydro extractor/ Drying tumbler/flat bed press machine/bioler/any other equipment in laundry plant etc and material and labour for re-winding of electric motor with super enameled copper wire of good quality with same gauge and same size complete with all accessories including varnishing the winding for improvement of insulation by heating method and reassembling, installing, commissioning and testing after repair / rewinding, greasing and gland packing & necessary balancing arrangement with rubber bushes complete including transportation charges from site to work shop and back to its original position complete all as specified and directed for the following capacities:-

(a) up to 2 Hp

(b) above 2 HP to 5Hp

(c ) above 5Hp to 10Hp

M&L for spray painting of Steam Boilers and chimney at laundry plant MH (incluing inner and outer surface areas,motors,disel tank and econimizer also, except stainless steel part/electric panels/belts etc) by apply two coats of metal primer and painting with two coats synthetic enamel paint of existing colour after removing all dust & rust and paint shall confirm to IS 2032 including marking of SM/MES Number for each equipment with stencil letter with black or white paint and Font and Size of letter and white washing for PCC based plinth shall be directed by Engr-in-Charge.

M&L descaling of the following laundry equipments with approved descaling chemicals complete all as specified and directed.

Washing machine of 100 Kg capacity

Washing machine of 50 Kg capacity

600 Kg/hr boiler

Supply & Fixing following spare parts suitable to Hydro Extractor of capacity 50Kg including taking down old unserviceable spare parts complete all as specified and directed for Make Hydro extractor :Megha laundry Eqpts

Contactor ML1, 3 phase, 415 volts

Timer relay

Transformer

Timer

Buffer

Limit switch

Main motor bearings

Push button

Motor to body springs

Rubber bush for Hydro Extractor

Hydro Extractor motor bearings

Bridge rectifier

Diode

Body Spring support Bolts

Supply & Fixing following spare parts suitable to Air Compressor suitable for capacity up to 2HP including taking down old unserviceable spare parts complete all as specified and directed

Limit switch

Motor bearings

Compressor Bearings

Piston Kit

Drain out the fuel from the fuel tank of Boiler of capacity up to 1000ltrs and keeping it in separate container safely, disconnecting all the fuel lines and other mechanical connections and taking out the fuel tank for cleaning, internally and externally by removing all the accumulated dirt/ sediment, leak testing the tank and welding/ brazing including one coat of synthetic enamel paint, refixing the tank in its original position, replacing the drain plug and PVC pipe, calibrating the fuel tank, refilling the drained out fuel back into the tank and marking of liters in gauge and provision of locking arrangements complete all as directed by Engr-in-charge.

S&F of 4 pole power contactor MCX-23, 50Hz suitable for existing one and including taking down old unserviceable one complete all as directed by Engineer-in-Charge Make:- L&T / Schneider / Siemens

S&F of 4 pole power contactor MCX-33, 50Hz suitable for existing one and including taking down old unserviceable one complete all as directed by Engineer-in-Charge Make:- L&T / Schneider / Siemens

M&L for spray painting of 50kg capacity hydro extractors at laundry plant MH (incluing inner and outer surface areas and motors also, except stainless steel part/electric panels/belts etc) by apply two coats of metal primer and painting with two coats synthetic enamel paint of existing colour after removing all dust & rust and paint shall confirm to IS 2032 including marking of SM/MES Number for each equipment with stencil letter with black or white paint and Font and Size of letter and white washing for PCC based plinth shall be directed by Engr-in-Charge.

diito - all as per item no.22 but for 25kg Hydro extractor

All as per Item. 22 above but for flat bed press at laundry plant MH all as directed by Engr-in-Charge.

All as per Item. 22 above but for sluice machine at laundry plant MH complete directed by Engr-in-Charge.

All as per Item. 22 above but for calander machine at laundry plant MH all as directed by Engr-in-Charge.

All as per Item. 22 above but for Air compressor unit at laundry plant MH all as directed by Engr-in-Charge.

M&L for painting of MS/GI pipe line of different sizes by applying two coat of synthetic enameled black colour paint after removing all dust & rust and paint shall confirm to IS 2032 shall be directed by Engr-in-Charge.

S&F in MS Pipe line laid in trenchs/duct/ug/surface/wall/floor alongwith aluminium Cladding insulation including following accessories complete all as directed by Engr-In-Charge at the Loundry Plant at Military Hospital

2 1/2" MS C Class Pipe

2 1/2" MS T/E Flanges

2 1/2" MS Long Bends

25mm C Class Pipe

25mm T/E MS Flange

1"x 6" MS long Bends

1"x 6" MS Nipples

1" Elbow

1" Steam Traps

1" MS Union

1" Axe Nipples

Bolts and Nuts suitbale to existing Pipes at Loundry plant , MH

1/2" Teflon tapes

1" globe valves

Welding Rods

Metallic Sheet

Cutting Wheels

M&L for door bedding for 50/100kg washing machines/drying tublers located MH laundry plant including taking down old unserviceable one complete all as directed by Engr-in-Charge.

Design Fabricating supply and errecting connecting and testing totally enclosed wall mounted LT cubicle panel board 3 Phase 4 wire system outdoor double door front and back opening type, sloped canopy (Hood) on top extended 100mm all arround, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 95 Sqmm 3.5 core in and out , incoming and out going feeders duly marked on revited plates etc complete CPRI approved factory made fabricated out of 2mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy powder coated mat finish of SIEMENS GREY structural RAL 7032 shade colour,built in industrial type locking arrangement on front and back ,and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs

(a) Bus bar aluminium duly insulated with colour coded heat shrinkable sleeve and mounted on suitable size of 'F' class insulators made of non hygroscopic,non combustible,track resistant high strength FRP insulators 200 Amps for phases and neural set of 4 for RYB &N set of 04 - 01 set (b) MCCB Four Pole 415 Volts 50 Hz 25 Amps adjustable Thermal Magnetic type with repturing capacity of 16 KA - 01 No of Make : Legrand, Cat No. 420011. (c) MCCB FTHREE Pole 415 Volts 50 Hz 16 Amps adjustable Thermal and Fixed Magnetic type with repturing capacity of 16 KA - 02 Nos ( 02 Nos for 3HP Pumps) of Make : Legrand, Cat No. 420010.

M&L for spray painting of Diesel mono block fully autimatic burners of Oil fired Incinerator at MH (incluing inner and outer surface areas and motors also, except stainless steel part/electric panels/belts etc) by apply two coats of metal primer and painting with two coats synthetic enamel paint of existing colour after removing all dust & rust and paint shall confirm to IS 2032 including marking of SM/MES Number for each equipment with stencil letter with black or white paint and Font and Size of letter and white washing for PCC based plinth shall be directed by Engr-in-Charge.

All as per Item No. 32 above but for Primary chamber of Oil fired Incinerator at MH all as directed by Engr-in-Charge

All as per Item No. 32 above but for Secondary chamber of Oil fired Incinerator at MH all as directed by Engr-in-Charge

All as per Item No. 32 above but for Hydraulic ram of Oil fired Incinerator at MH all as directed by Engr-in-Charge

All as per Item No. 32 above but for Chimney of height 15m of Oil fired Incinerator at MH all as directed by Engr-in-Charge. Note :- Rate quoted shall be inclusive of arrangements of safety measures i.e., scaffolding arrangement etc.

S&F Economizer suitable for diesel boiler 600 Kg/Hr including Shell which be like a house for tubes and header. Tubes of economizer should have capability to transfer high heat, has resistance to heat, corrosion, and erosion, Baffle has to support tube and maintain its position, and also to prevent vibration on the tube and control and direct the flow of fluid outside tubes, Header used as a water collector and distribute water to each tubes evenly, tubes are connected into header, so header has size and mount of hole in accordance with tubes condition, Tie rods and spacer to maintain position one baffle and other baffle so vibration can be prevented complete all as specified and directed by Engineer-in-Charge. Make of boiler: Thermax

S&F 2000 Ltrs capacity rotational mountain polythene water storatge water tank tripple layered as per IS-1270 - 1989 hoisted 2500 dia ball valve brass eith plythene float and fly nut and fixed in position including suitable inlet & outlet pipe ine connections & necessary platform complete including removing existing unserviceable tank complete all as directed. Make: Sintex / Polycon

M&L of cross arm i.e., bracing supporting clamps back plates, nuts, bolts and washers complete including one under coat and one finishing coat with synthetic enamel paint over a coat of red oxide primer & including taking down old unserviceable complete all as directed by Engineer-in-Charge.

Supply, lay, connect test and commissioning of solid copper conductor cable XLPE insulated screened PVC tape innersheathed, unarmoured electric power cable heavy duty with aluminium conductor 1100 volts grade corss sectional area of 16 Sqmm single Core confirming to IS:7098 Part-I laid in trenches/floors complete testing and commissioning complete all as directed. Make :- KEI Industries Ltd or equivalent in Havells/ Polycab/Plaza

All as per Item No. 40 above but for 25Sqmm single core all as directed by Engineer-in-Charge

All as per Item No. 40 above but for 50Sqmm single core all as directed by Engineer-in-Charge

M&L attending complaints for Laundry plant, Incinerator, Oxygen manifold syste of emergency basis to clear/rectify both electrical and mechanical faults installed at various locations under AGE E/M No.II Complete all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar or cement lime mortar including all quoins, arches,pillars, ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L Pre-cast cement concrete block masonry Type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10cm in width and setting in cement mortar 1:6 complete

M&L for brick work with sub class B bricks, straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) complete all as specified and directed.

All as per item No. 46 above, but except bricks (using old bricks obtained from demolition)

M&L walling of Random Rubble masonry, uncoursed, well bonded, bedded and solidly hearted and built in cement mortar (1:6) complete all as specified and directed.

All as in Item No.48 above but for except stones (using old stones obtained from demolition)

M&L raised pointing to random rubble masonry walls uncoursed in cement mortar (1:4) complete all as specified and directed.

M&L PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in foundations filling and mass concrete complete all as specified and directed.

M&L for demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level)complete all as specified and directed.

M&L PCC 1:4:8, type C-2 (40mm graded aggregate) in 100 mm thick as a sub base of floor including necessory form work complete all as specified and directed.

M&L for 40mm thick PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in flooring including necessory form work and finishing the top surface even & smooth, without using extra cement complete all as specified and directed.

Supply only glass dividing strips 38 mm wide and 3 mm thick and inserted in position confirming to design complete all as specified and directed.

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in any type of soils complete all as specified and directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5 above the starting point complete all as specified and directed.

Hardcore of gauge n exc 63mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

All as per item No. 58 above but of gauge 20mm to 40mm mixed graded for transformer yard etc

M&L for machine pressed interlocking paver blocks of 80mm thick with grey cement and no pigmet any shape and size confirming to IS 15658-2006 of M-40 grade all specified and directed

M&L for fine aggregate ( course Sand) as in back layer and cushioning for interlocking paver blocks, spread and required levelling etc., complete all as specified and directed.

M&L for chequerred cement concrete tiles 25 cm x 25 cm x 22mm thick with grey cement and no pigmet, machine pressed, set, jointed and pointed in neat cement slurry in floors over and including 20 mm thick screed bed in cement and sand mortar 1:6, complete all as specified and directed.

M&L PCC 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) as in steps, plinth courses, parapets, copings, bed plates, kerbs etc. water troughs and the like including necesaary formwork,complete all as specified and directed.

Taking down cement plaster of any description from existing old walls (to receive plaster) including raking out joints, hackisng for key, scrubbing down with water etc.., complete all as specified and directed.

Rendering 10 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and directed.

Rendering 15 mm thick in cement and sand mortar 1:6 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and directed.

Rendering 5 mm thick in cement and sand mortar 1:4 on concrete surfaces of ceiling including finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly plastered surfaces of Walls and applying with three coats of white wash complete all as specified and directed.

All as per item No. 68 above, but on ceilings.

M&L for preparation of newly treated surfaces and apply two coat of oil bound distemper over one coat of chalk whitening to walls complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated) sheets including ridges as in roof covering complete all as specified and directed.

Dismantling timber scantling of any section in fillets, rails, posts, rafters, purlins, in any position (unframed) complete all as specified and directed.

S&F steel work in tubular trusses / poles (unframed) including purlins, rafters and special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS-1161-1979 grade St-240 complete all as specified and directed.

S&F mild steel plates (plain or chequerred) channels, square cut or notched (ordinary and counter sunk)forming with hole for nuts etc complete all as directed.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws including ridge complete all as specified and directed.

Excavation in post holes (or similar holes) each n.exc 0.50 cu.m getting out in any type of soils, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm complete all as specified and directed.

M&L PCC 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) in foundations, filling and mass concrete

M&L for framed structural steel works in fencing post of angle iron, base plate, brackets etc. drilled and fixed with nut & bolts with fixing strip of FI complete all as specified and directed.

Supply only chain link MS galvanised fencing wire any size including line wires, to any type of standards rails, straining bolts etc., including provision of binding with mild steel wire annealed not less than 0.9mm dia including dismantiling old unserviceable mesh complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc., laid in position including provission of binding wire complete all as specified and directed.

S&F galvanised 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts including securing or tying at crossing with provision of galvanised mild steel wire, stapples or steel pin etc., fixed in repairs complete all as specified and directed Note:-Each line wire will be measured and paid.

S&F Framed mild steel work such as grills, grating, gates with ends of bars shouldered and / or rivetted, or forged into spikes, framed gurad bars, barred iron doors, ladders, framed balusters, walk ways railings and similar work confirming to Fe- 290 Gde E-165 of any section and sizes, including taking down old gates or ladders of any size and in any position complete all as specified and directed.

M&L rolled sections as in main & cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors and rolling shutters fixed with angle cleats or other connecting pieces including dismantling old structural steel work complete all as specified and directed.

S&F steel rolling shutters, thickness of laths 1.25mm with gear opertaing type with level gear box and crank handle, without ball bearing including top cover, hasp and staple and one shop coat of primer, erected in position as indicated and two coats of synthetic enamel paint including taking down old unserviceable shutter complete all as specified and directed.

S&F ball bearing for rolling shutter complete all as specified and directed.

S & F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not exc 10 cm width or girth and priming with red oxide zinc chrome and painting with two coats of synthetic enamel paint complete all as specified and directed.

M&L for dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) rubbish off the premises complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick area of each tile exceeding 0.06 but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic tile 300 x 200 x 06-7mm thick (coloured) on vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick plaster in cement and sand mortar 1:4, complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per srl item No.93 above but on skirting including back layer of 10mm thick plaster in CM 1:4.

M&L forVirified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per srl item No.95 above but for dark shade

All as per srl item No.95 above but on skirting including back layer of 10mm thick plaster in CM 1:4.

M&L 20-25 mm thick machine cut kota stone slab as in flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including 20mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per srl item No.98 above but in riser of steps, skirting, dado and pillar including back layer of 10mm thick plaster in CM 1:4 complete all as specified and directed.

M&L Machine cut cudappah stone slab 20-25mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

S&F for Sink with draining board made out of stainless steel 1.00 mm thick sheet for kitchen with plugs, washers and wastes including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410 mm x 330mm x 160mm supplied and fixed in repairs complete all as specified and directed.

M&L for Vitreous China squatting pan “Orissa pattern” size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes etc fixed in repairs complete all as specified and directed.

Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) and incl Plastic water closet seat and cover, with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes etc fixed in repairs complete all as specified and directed.

M&L for PVC low level flushing cistern, ISI marked, valveless, syphonic action type, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 90 cm long etc, supplied and fixed in repairs complete all as specified and directed.

M&L for vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe fixed in repairs (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

M&L for vitreous china wash basin, white, flat back, size 550x400mm including waste fitting chromium plated brass, chromium plated steel chain and rubber plug, porcelain stopper, a pair of CI brackets, waste pipe and pillar tap etc. fixed in repairs complete all as specified and directed.

S&F for PVC connection 15 mm size, of length 450 mm, with PTMT nuts supplied and fixed in repairs complete all as specified and directed.

S&F in repairs grating doom 125mm dia with waste hole of PTMT fixed on floor/nahani trap with cement mortar, fixed in repairs complete. (Minimum weight 40 gms) complete all as specified and directed.

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc.,complete all as specified and directed.

All as per item No.110 above, but 20 mm bore.

S&F for 15mm bore tubes, medium grade, galvanised with and including all fittings fixed to walls, floors, or ceiling or laid in floors etc., complete all as specified and directed.

All as per srl item No.112 here in before but 20mm bore.

S&F for stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm, supplied and fixed in repairs complete all as specified and directed.

All as per item No.114 here- in- before but 20 mm bore.

S&F for bib taps, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, for bore dia of pipe 15mm, supplied and fixed in repairs complete all as specified and directed.

S&F Bib tap standard of PTMT fancy type any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-105gms) screwed for iron pipe 15 mm bore, supplied and fixed in repairs complete all as specified and directed.

S&F for Pillar taps cast copper alloy, fancy type with capstan head, CP, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nut, screwed for iron pipe 15 mm bore, supplied and fixed in repairs complete all as specified and directed.

S&F for Pillar taps of PTMT, fancy type any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-120gms) screwed for iron pipe 15 mm bore, supplied and fixed in repairs complete all as specified and directed.

S&F for PVC (SWR) pipes 110 mm bore single socketed, in any length with and including rubber ring joints, fixed on walls complete including taking down old existing PVC rain water pipe complete all as specified and directed.

S&F for PVC (SWR) bends (any radius) 110 mm bore complete all as specified and directed.

Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required for depth exc one brick but not exc. two bricks

All as per item no.122 above but in stone walls built in cement mortar or in cement lime mortar

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 sqm and not exceeding 4.00 sqm each complete all as specified and directed.

Taking down shutters of any description, area exceeding 1 sqm and not exceeding 2.00 sqm each complete all as specified and directed.

Refixing the shutters area exceeding 1 sqm and not exceeding 2.00 sqm each, including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed.

M&L for Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia threshold bar and filling hollow of frame with plain cement concrete Type C-0, 1:3:6 (using 12.5 mm graded crushed stone aggregate) of size of frame 105mm x 60 mm complete all as specified and directed. Note for item No 79 & 80 : Threshold bar and PCC shall be measured and paid separately

M&L for PCC 1:3:6 type C0 using 12.50 mm graded stone aggregate for hold fast blocks of chowkats etc including necessary form work for rough finished surfaces etc., complete all as specified and directed.

S&F for 35mm thick plain framed, panelled shutters(two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003(Part I),kiln seasoned and chemically pressure treated in 2nd class HW complete all as specified and directed.

S&F for Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2004 complete all as specified and directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as a gap insert for top rail and bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S frame welded / sealed to the stiles and nails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at side as per specification and drawings complete all as specified and directed.

S&F for steel windows with side hung shutters including hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F for 75 mm size butt hinges ,extruded Aluminium alloy with galvanised mild steel hinge pin,type-C-21. (ISI Marked), rolled mild steel complete all as specified and directed.

S&F for 150mm size Aluminium anodized barrel Tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 150mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed.

S&F for 250mm size extruded aluminium alloy sliding door bolt, fabricated type anodized complete all as specified and directed.

S&F for stainless steel wire-cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

All as per the srl item No.137 above but fixed in repair.

M&L for painting to new wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with pink primer (one coat) finished with two coats of synthetic enamel paint complete all as specified and directed.

M&L for hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones glazed with oil putty fixed with beads complete all as specified and directed.

M&L for 3 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and directed.

S&F for aluminium frame for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc including powder coating to the sections ( minimum thickness of powder coating 50 micron) complete all as specified and directed.

M&L for aluminium door shutter powder coated (thickness of powder coating shall not be less than 50 micron) as per IS standards sections, any colour, aluminium sections weighing 0.55 kg/m including necessary jointing cleats, glazing clips rubber or neoprine packing, handels 2 nos each door, hinges, aluminium snap beading screws etc complete all as specified and directed.

S&F for door closer of cast iron body, hydraulically regulated, designation No 2, universal type, suitable for door shutters of weight between 36 to 60 Kg, ISI marked, fixed in repairs complete all as specified and directed.

M&L for 5 mm thick sheet glass, ordinary quality and glazing with beading or PVC beads in square exceeding 0.5 square metre in each pane complete all as specified and directed.

M&L for veneered decorative plywood 9/12 mm thick, grade 1 (with BWR resin) with decorative face veneers on both face, fixed with screws to timber frame work as in aluminium door shutter etc. complete all as specified and directed.

M&L for preparing old treated surfaces of walls (plastered or unplastered surfaces) and applying one coat of white wash on old decorated surfaces complete all as specified and directed.

All as per Srl item No. 147 above but on ceiling

M&L for preparing old treated surfaces of walls (plastered or unplastered surfaces) and applying one coat of cement base paint complete all as specified and directed.

M&L for preparing old treated surfaces of walls (plastered or unplastered surfaces) and applying one coat of oil emulsion distemper (white / tinted) complete all as specified and directed.

M&L for preparing old painted wooden/wood based surfaces over 10cm width or girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified and directed.

M&L for preparing old painted steel surfaces over 10 cm width of girth and applying one coat (finishing coat) of synthetic enamel paint complete all as specified and directed.

M&L for round bars of size 10mm dia and over cut length, bend to shape reqd, including cranking, bending, sprially for hooping for cols, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for pre cast cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in cover slabs (for manholes etc) and similar articles with plain faces, set in CM 1:4 complete all as specified and directed.

M&L for mild steel 6 to 8mm dia TMT bars bent to shape required, including cranking, bending and binding with mild steel annealed wire not less than 0.9mm dia complete all as specified and directed.

Taking down cement or cement lime plaster from roof top inluding removing old water proofing roof treatment of any description and cleaning surfaces with wire brush, removing dust, debris material obtained from demolition out side Def land complete all as specified and directed

M&L for cleaning concrete surfaces with wire brushes, removing dust and applying water proofing treatment as under (i)Apply oil bound bitumen [email protected] litre/sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 kg/litre at 25 degree celsius on the prepared dry roof surface. (ii)Laying APP polymer modified membrane weight @3.8kg/sqm and 3mm thick reinforced with non woven polyester mat by torch applicationon membrane with 100mm over lap (iii) Top of membrane surface shall then be finished with solar reflective bituminous aluminium paint @ 0.1 ltr/sqm complete all as specified and directed

Srinivasa Consructions

Dwarka Pershad Radhey Ramanlal