PROVISION OF PARKING SHED FOR TRACTOR EQPTS AND HY STORES NEAR STATION CELL PROVISION OF TOILET FOR GUARD NEAR BLDG NO P196 AND ADDN ALTN TO BLDG NO P216 AT LICHUBARI IN MIL STATION JORHAT UNDER GE JORHAT

Amount

Demolition of reinforced cement concrete of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4.0 Sqm each, complete all as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as directed.

Surface dressing not exc 15 cm deep in soft/ loose soil, complete all as specified and directed.

Excavation in trenches, not exc. 1.5 m wide and not exc. 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying pipe, cable, etc. n exc 10 sqm on plan and not exc. 1.5 m in depth and getting out in soft/ loose soil, complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

Returning filling in soft/ loose soil, including spreading, levelling, watering and well ramming in layers not exc. 25 cm, complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level not exc. 1.5 m above the starting point, complete all as specified and directed.

Material and labour for, hardcore of gauge not exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

Material and labour for, RCC (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed.

Material and labour for, RCC (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in as in columns, pillars, piers, posts and struts, complete all as specified and directed.

Material and labour for, RCC (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed.

Material and labour for, RCC (1:1.5:3) type A1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

Material and labour for, 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, complete all as specified and directed.

Material and labour for, brickwork with subclass ‘B’ bricks, old size, straight or curved on plan exc. 6m mean radius built in cement mortar (1:6), complete all as specified and directed.

Material and labour for, brickwork with sub class ‘B’ bricks, old size brick, straight or curved on plan to any radius in half brick thick walls built in CM (1:4), complete all as specified and directed.

Material and labour for, use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams, etc., rough finished surfaces of concrete, complete all as specified and directed.

Material and labour for, use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete, complete all as specified and directed.

Supply and fix for, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as per specification & drawing.

Supply and fix for, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as per specification & drawing.

Supply and fix for, factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, complete all as specification and drawing.

Supply and fix for, solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing.

Supply and fix for, 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 200mm long, complete all as specified and directed.

Supply and fix for, aluminium handles, cast type, anodised 150mm size complete all as specified and directed.

Supply and fix for, harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc, complete all as specified and directed.

Supply and fix for, 150mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

Supply and fix for, 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

Supply and fix for, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and fix for, aluminium (extruded section body) door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed

Supply and fix for, mortice lock, vertical type, size 100 mm 4 livers brass, complete all as specified and directed.

Supply and fix for, mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5cm long and dis of bolt 5 to 10mm, complete all as specified and directed.

Supply and fix for, mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Supply and fix for, rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde- E- 250) quality- A, complete all as specified and directed.

Supply and fix for, rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-290 Gde E-165, complete all as specified and directed.

Supply and fix for, rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed.

Supply and fix for, mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Material and labour for, mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Supply and fix for, anodised aluminium frame powder coating (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Supply and fix for, anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

Supply and fix for, anodised aluminium powder coated (minimum thickness of powder coating 50 micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

Supply and fix, anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Material and labour for GI frame work for seamless ceiling comprising of Giperimeter channel 0.55mm thick with two unequal flanges or 20 and 30mm and web of 7mm fixed to sorrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and sheet expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre including 10mm thick plaster of paris ceiling (Gypsum anhydrous), complete all as specified in SSR and directed.

Material and labour for, 100mm thick plain cement concrete (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in sub base floor, complete all as specified and directed.

Material and labour for, 75mm thick plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in sub base floor, complete all as specified and directed.

Material and labour for, 75mm thick plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in plinth protection, finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.11 Sqm but not exc.0.18 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6) including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.18 Sqm but not exc.0.38 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6) including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Materials and labour for, glazed ceramic coloured tiles, 450 X 350 X 7mm/ 350 X 250 X 7mm thick, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat in cement mortar (1:4) including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Material and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:6) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, rendering 5 mm thick, cement plaster, in cement mortar (1:3) on fair faces of concrete surfaces on ceiling, finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed. (Note: Water proofing compound shall be measured and paid seperately under relevant item).

Supply only integral water proofing compound complete all as specified.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of acrylic emulsion distemper over a coat primer over 1mm thick wall putty, complete all as specified and directed.

Material and labour for, preparation of old decorated plastered ceiling surfaces by washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of acrylic base distemper, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat primer, complete all as specified and directed.

Material and labour for, complete removal of existing treatment and applying two coats of cement base paint over a coat of primer including preparation of surfaces, complete all as specified and directed.

Material and labour for, complete removal of existing treatment on wall surfaces and finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm over and including 1mm thick plaster of paris putty over plastered surface to prepare the surface even and smooth, complete all as specified and diorected.

Supply and fix for, 4.0 figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sq. m in each pane, complete all as specified and directed.

Supply and fix for, 5.5mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane, complete all as specified and directed.

Supply and fix for, solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified and directed.

Supply and fix for, solar control film 50 micron reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Supply and fix for 15mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for 20mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix, pillar taps, fancy type, cast copper alloy, chromium plated, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

Supply and fix for, stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply and fix for, angle stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed.

Supply, hoisting and fixing in position of rotational moulded polyethylene water storage tanks double layers (cylindrical vertical with closed top) of 1000 litres capacity with ISI marked and all as specified in IS12701 including 20mm bore dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified in SSR Part I and directed.

Supply and fix for counter top basin of size 615 x 415 x 150mm all as per Cat No.DRS-WHT-37601 of Jaquar including bottle trap, waste fittings screwed for iron pipe or for brass ferrule etc complete all as specified and directed.

Supply and fix for, two way bib tap with flange all as per Cat No.G5234A1/ T4634A1 of Parryware or as specified in PS including fittings screwed for iron pipe or for brass ferrule etc, complete all as specified and directed.

Supply and fix for, vitreous china wash down water closet pan (EWC) (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

Supply and fix for, health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply and fix for, PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

Supply and fix in repair for, 15mm dia CP fancy type wall mixer with 'L' bend (including provision of O/H shower & hand shower) for mixing hot and cold water with hand shower HSH-1717 and tube all as per Cat No. QQT-7281 of Jaquar or as specified in PS, screwed down for iron pipe, complete all as specified and directed.

Supply and fix for, vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe), including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing, grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed.

Supply and fix for, 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and making good the disturbed floor/ surfaces, complete all as specified and directed.

Supply and fix for, toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws, complete all as specified and directed

Supply and fix for, soap dish, vitreous China white, approximate size 160x 160x 90mm, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc. complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) bends any radius with access door, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed.

Supply and fix for 100mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

M/S RAJIB GOSWAMI ENTERPRISE (BID ID -3428855)

MD ABIDUR ALI (BID ID -3426634)

SANDHUSONS (BID ID -3420905)

M/S DHAR AND DHAR (BID ID -3428647)

SUBHAS CONSTRUCTIONS (BID ID -3419719)