SPECIAL REPAIRS TO BLDG P 62 AT PRTC T 35 7 8 9 10 AT ML LINE AREA UNDER GE NORTH BANGALORE

Amount

B/R WORKS

Dismantling of single layer Mangalore pattern roofing tiles or similar tiles in roofing etc complete all as specified and as directed.

Dismantling of wooden timber fillets, rails, posts, rafters, purlins etc not exceeding 40 sqcm in section all as specified and as directed.

Dismantling of timber scantlings in any position unframed work 40sqcm and over in section all specified and as directed.

Second class hard wood scantling clean sawn timber scantling in unframed work 40 sqcm and over in section all specified and as directed.

All as per item no 1.004 but except timber.

Rolled mild steel work as in joist, channel, angle, or tee sections, as in purlins fixed independently, without connecting plates, etc. of grade Fe 410-W complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixd with self tapping screws all as specified and as directed.

As per item No 1.007 above but plain sheet for ridge.

E-grid suspended false ceiling grid system of size 600mm x 600mm with main tee 32 x 24 x 0.6mm cross Tee 25 x 24 x 0.6mm and wall angle 22.2 x 22.2 x 0.5mm, ceiling suspended with 3mm dia GI wire hanger fixed with steel dash fastener, butterfly clips, hold down clips etc., (Main runner, cross Tee & wall angle of MS galvanised with PPPCGS) including 4mm thick HPSC self textured design pre primered non asbestos fibre cement building board fixed to false ceiling including one coat of oil bound emulsion distemper complete all as specified and as directed.

Taking down door frame or chowkats without taking off shutter from frame area n.exc 1.50 sqm each all as specified and as directed.

Taking down chowkats or frame area exc. 1.5 sqm but n.exc. 4 sqm (without taking off shutters) from the frame all as specified and as directed.

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete of size 125 x 60mm all as specified and as directed.

Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete of size 105 x 60mm all as specified and as directed.

35 mm thick factory made second class hard wood panelled door shutters (two pannels) with lock rail and panel of 9mm BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both sides,size of style and rail as per IS: 1003(Part-I) kiln seasoned etc complete all as specified and as directed.

35 mm thick factory made door shutter second class hard wood fully glazed skeleton shutters,open rebated and prepared to receive glass, gauge etc., divided into squares with plain chamfered, mitred and rebated sash bars any numbers fitted with cut and mitred beads for securing glass etc., complete all as specified and as directed.

18/19 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work including teak wood lipping, as in cup board shutters and shelves, pelmet Boxes etc., complete all as specified and as directed.

PVC door frame of size 50mm X 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube. Fixing in opening as per specification all as specified and as directed.

Factroy made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with neat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuck inside the solvent cement for stiles and plain coloured PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rails and bottom rail panelling of plaincolour PVC sheet to be fitted in the MS frame welded to the style and rails with suitable PVC sheet beading and jointed together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and as directed.

PTMT butt hinges, 100 mm long and fixed with steel screws complete all as specified and as directed.

PTMT tower bolts, 150 mm long and fixed with steel screws complete all as specified and as directed.

PTMT door handle, 150 mm long and fixed with steel screws complete all as specified and as directed.

Steel windows double rebated with box type frame, side hung shutters, on one side glazed and other side gauzed shutter including projected type hinges, 100mm long steel handle, 150mm long tower bolt and steel peg stay all as per TD drawing-539 sheet 1/3 to 3/3 including filling frame with Plain Cement Concerte (1:3:6) type C-0 using 12.5mm graded stone aggregate complete all as specified and as directed Engineer-in-Charge.

Steel Ventilators with box type frame, top hung shutters including hinges, steel peg stay complete with glazing bars all as specified and as directed.

Mild steel square bars of size 12 mm as in grill or guard bars welded to steel window all as specified and as directed.

Stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed in repairs complete all as specified and as directed.

Sheet glass 3.0mm thick, ordinary quality and glazing with Silicon and securing pins n.exc 0.50 sqm in each pane complete all as specified and as directed.

Figured glass, 4.00 mm thick, pin headed type and glazed with oil putty in square n.exc 0.50 sqm in each pane all as specified and as directed.

Mild steel small items such as hold fast, strips for rain water pipes bend stray support etc all as specified and as directed.

Cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in hold fasts, bed blocks etc including necessary form work complete all as specified and as directed.

200mm long Aluminium barrel tower bolt etc complete all as specified and as directed.

300 mm long Aluminium alloy anodised sliding door bolt (Aldrop bolt) with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed etc complete all as specified and as directed.

MS butt hinges medium weight 100mm long cold rolled all as specified and as directed.

150mm long Aluminium handles fabricated type all as specified and as directed.

Taking down cement plaster with / without tiling on brick or concrete surfaces including racking out joints, hacking for key, scrubbing down with water etc., and disposal of debris outside MD land all as specified and as directed.

Rendering 15mm thick on surface of brick work/concrete surface in CM (1:6) and finishing the surfaces even and fair without using extra cement complete all as specified and as directed.

Rendering 15mm thick in CM(1:4) on other than fair faces of brick or concrete surfaces, and finishing the surfaces even and fair with out using extra cement all as specified and as directed.

Preparation of new plaster surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of oil bound distemper over a coat of alkali reistant primer on wall complete all as specified and directed.

Preparation of old un treated surfaces of any description including brooming down with steel wire brushing scrapping down soot’s, moulds, moss and efflorescence, salts, trading oil and greasy spots etc on wall surfaces and applying one coat of oil bound emulsion distemper all as specified and as as directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer all as specified and as directed.

Preparation of old un treated surfaces of any description including brooming down with steel wire brushing scrapping down soot’s, moulds, moss and efflorescence, salts, trading oil and greasy spots etc on wall surfaces and applying one coat of cement based paint all as specified and as as directed.

Preparation of new/old plastered wall surfaces of any description and applying three coats of white washing complete all as specified and as directed.

Preparation of new or previously untreated wooden surfaces of any description not other wise described over 10cm width or girth applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Preparation of new or previously untreated steel and iron surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel over a coat of red oxide primer, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing) removing seviceable tiles to store and rubbish off the premises complete all as specifed and as directed.

Non skid ceramic coloured tiles 7-8mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc, set and jointed in neat cement slurry to match surfaces over and including 15mm thick cement mortar screed bed in CM (1:6) all as specified and as directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tiles exceeding 0.11 sqm but n.exc. 0.18 sqm, as in floors etc set and jointed in neet cement slurry and pointed in white or coloured cement to match over including 20 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

Glazed ceramic coloured tiles of size 300 x 200 x 7 mm thick as in vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match over including 10 mm thick backing coat in cement mortar (1:3) on fair faces of brick work or concrete surfaces complete all as specified and as directed.

Demolition in cement concrete (unreinforced) in ground floor and pavings n.exc. 15 cm thickness (above ground level) and disposal of debris outside MD land all as specified and as directed.

Plain Cement Concrete (1:2:4), type B1 using 20mm graded stone aggregate, 40mm thick as in floors finished even and smooth using extra cement all as specified and as directed.

Taking up or down steel tubing 15mm dia and connections all as specified and as directed.

Taking up or down steel tubing 20mm dia and connections all as specified and as directed.

Galvanised iron tubing medium grade 15mm dia with all fittings and fixed to wall, ceiling or laid in floors etc., complete all as specified and as directed.

Galvanised iron tubing medium grade 20mm dia with all fittings and fixed to wall, ceiling or laid in floors etc., complete all as specified and as directed.

Bib taps, 15 mm bore chromium plated, fancy type, long body cast copper alloy with capstan head handle , screwed down for iron pipe or for brass ferrule fixed in repairs complete all as specified and as directed.

Stop valves, 15mm dia fixed in repairs, cast copper alloy, screwed down high pressure with crutch or butter fly handle screwed both ends or for unions etc., complete all as specified and as directed.

Stop valves, 15mm dia fixed in repairs, cast copper alloy, screwed down high pressure, fancy type, with crutch or butter fly handle, with long shank and cup (concealed type) screwed both ends or for unions etc., complete all as specified and as directed.

Gratings chromium plated of size 125 mm dia with waste hole of suitable size all as specified and as directed.

Rotational moulded polythene water storage tank (cylindrical vertical with closed top) with ISI mark embosed on it, hoisted and fixed in position complete all as specified in SSR part I capacity of tank 500 ltrs capacity complete complete all as specified and as directed.

20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed(Min weight 20mm-210 gms) all as specified and as directed.

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC(SWR) P trap connecting to flush pipe and to anti syphonage pipe, etc. complete including making good to floor fixed in repairs complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, 10ltr capacity,low level, white, with inlet, ball valve, float and handle including brackets, connections to pipes and fixing of chain and pull, or lever, fixed in repairs complete all as specified and directed.

PVC connections 15mm dia with PTMT nuts of length of 450 mm long fixed in repairs complete all as specfied and as directed.

Vitreous china wash hand basin, white, flat back of size 630 x 450 mm excluding taps,chain and plug and porcelain stopper but including CI bracket. etc complete fixed in repairs all as specified and as directed.

15 mm dia cast copper alloy chromium plated Pillar tap fancy type screwed for iron pipe and fixed in repairs complete all as specified and as directed.

32 mm dia waste fittings, brass, chromium plated for sinks, basins, etc., with long screwed shanks and flynuts, flange end fixed in repairs complete all as specified and as directed.

Towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats all as per Prayag Cat No. 200 (minimum weight 190gms) completed fixed in repairs all as specified and as directed.

125mm dia brass chromium plated shower rose with swivel joints fixed in repairs all as specified and as directed.

Demolition of brick or stone work built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles all as specified and as directed.

Brick work with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6) all as specified and as directed.

Ploished Machine cut cudappa stone slab as in cubboard slab/ Kitchen 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Over and including a sereed bed in cm 1:6, 15mm thick complete all as specified.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified

Stainless steel kitchen sink fixed in repairs 1 mm thick with plugs, washers and wastes coupling CP 32mm size, including bedding in CM to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 610x510mm bowl size 560 mm X 405 mm X 203 mm all as specified and as directed.

Drapery rods fixed in repairs 25 mm dia, having corrugated PVC extrusion with electric resistance welded MS pipe with fancy type 02 nos knob and 02 nos brackets for each door/windows etc complete all as specified directed.

Stainless steel plate rack fixed in repairs of size 1200X900mm made out of 1mm thick salem steel of Make : Maharaja or equivalent conforming to the pattern similar as approved all as specified and as directed.

Dismantling wall and ceiling boards (fibre pulp, insulation, etc) or insulation boards / slabs / blankets any thickness including cover fillets.etc complete all as specified and as directed..

Aluminium anodised snap grid frame work for false ceiling with grid size of 605 x 605mm, ceiling suspended with 3mm dia GI wire hangers fixed with steel dash fastener, butterfly clips, hold down clips etc., including 4mm thick HPSC self textured design pre primered non asbestos fibre cement building boards fixed to false ceiling including one coat distempering complete all as specified and as directed.

Fixing only in repairs non asbestos fibre cement building boards fixed or laid/ inserted to timber / GI / Aluminium framework with screws complete all as specified and as directed.

Complete removal of existing roof treatment (tarfelt) and removing debris to a distance of n.exc 50m all as specified and as directed.

Plain Cement Concrete, (1:2;4), type B-1, 40mm thick using 20mm graded stone aggregate including finishing cement concrete surface even and rough to receive finishing coats complete all as specified and as directed.

Screed bed or bedding layer of 15mm thick for laying floor finishes in CM (1:4) mixed with approved water proofing compound all as speciifed and as directed. Note: Water proofing liquid shall be measured and paid separately.

Supply only integral liquid water proofing compound all as specified and as directed.

Roof treatment by applying bitumen primer @ 0.27kg/sqm, providing 3mm thick APP modified water proofing membrane weighing not less than 3.8 kg/sqm reinforced with non woven polyester matt weighing not less than 180gm/sqm, having softening point not less than 140 centigrade, having tensile strength of 650 N/sq.cm in longitudinal and transverse directions, the reinforced tearing strength of 180N by torch application with minimum 10cm side overlap and 15cm end lap applying a coat of blown grade hot bitumen VG-10 over the membrane @ 1.2kg/sqm, top of membrane shall than be finished with solar reflective bituminous aluminium paint @0.10kg/sqm all as specified and as directed.

Plain Concrete Cement, (1:2:4), type B1 using 20mm graded stone aggregate as in coping, benching of manholes and similar work all as specified and as directed.

Precast Reinforced Cement Concrete (1:2:4), type B1, using 20mm graded stone aggregate as in cover slabs of man hole set in CM (1:4) complete all as specified and as directed.

TMT steel bars 8mm dia bars, cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Demolition of SGSW drain pipes of 150mm dia set and jointed in CM complete all as specified and as directed.

Salt-glazed stoneware drain pipes150mm dia laid in trenches and jointed in cement mortar complete all as specified and as directed.

Plain Cement Concrete (1:4:8), type D2 using 40 mm graded stone aggregatebed to drain pipes including packing under and haunching in against the sides of SWSG / RCC pipes after they are laid and tested suitable for 150mm dia bore pipe all as specified and as directed.

Preparation of old decorated surface of walls by broming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and threafter applying one coat of white wash on ceiiling complete all as specified and directed

Complete removal of existing treatment by preparation of old plastered surfaces of any description applying two coats of oil bound distemper over a coat of alkali reistant primer on wall complete all as specified and directed.

First class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints all as specified and as directed.

Flush door shutters, 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

French polishing on surfaces of any description, width or girth including cleaning and preparing the surfaces with a coat of wood filler on new works with two or more coats complete all as specified and as directed.

All as per Sl Item No. 1.093 above but one or more coats on old work.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/ spring clips, all as specified and as directed.

Gun metal globe/gate valves, 20mm dia with wheel head screwed both ends for iron pipe and fixed all as specified and as directed.

CP gratings of size 125 mm dia with waste hole all as specified and as directed.

Viterious china wash down water closet fixed in repairs with pan and trap (pedestal pattern ) white including connection to drain (outgoing pipe) and flushing pipe antisyphonic pipe including PVC seat cover closed pattern with flat bottom,and cover fixed with mild steel chromium plated or anodised hinging device excluding flushing cistern and flush pipe all as specified and as directed.

Plastic water closet seat cover fixed in repairs for pedestal pan, black , closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and as directed.

Health faucet 15mm dia, brass chromium plated with flexible pipe 1.2 mtr long and fixing nuts etc. complete fixed in repairs all as per (Jaquar Cat No. ALD-563 or techno commercially equivalent makes specified in PS complete all as specified and as directed.

Brass Mortice lock, 6 Levers, size 75 mm fixed to the doors in repairs, Make : Godrej or equivalent complete all as specified and directed.

Towel rail 600mm long of brass chromium plated fixed with and including Chromium plated brass screws and wooden/plastic cleats all as per Prayag Cat No. BA-10 completed fixed in repairs all as specified and as directed.

Soap dish all as per Cat No. BA-05 of Prayag polymers Pvt Ltd or equivalent complete all as specified and as directed

Toilet paper holder Cat No BA-08 of Prayag polymers Pvt Ltd or equivalent complete all as specified and as directed

E/M Works

Taking down carefully aluminium/ copper wiring/power point wiring (light, fan, socket or power) complete including fittings such as switches ceiling roses, regulators, sockets light fittings, fans etc and making good the disturbed surface of walls, ceiling etc incl painting with same colour of the back ground complete all as specified and as directed.

Point wiring complete with 1.5 sq.mm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with copper conductor conforming to IS 694 drawn through and including non-metalic rigid PVC conduit medium grade including accessories concealed type run on walls/ ceiling including MS terminal boxes fabricated with 1.6 mm thick MS sheet surface mounted/ concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., including provision of 1.5 sq.mm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed for one light point controlled by one switch.

All as per Sl Item No. 2.002 above but one fan point controlled by one switch/regulator.

All as per Sl Item No. 2.002 above but one 3 pin socket out let 5 Amps on independent board.

All as per Sl Item No. 2.002 above but one 3 pin socket out let 5 A on same board

Point wiring complete with 2.5 sq.mm single core PVC insulated unsheathed cable 1100 volts grade multi stranded with copper conductor conforming to IS 694 drawn through and incl non-metalic rigid PVC conduit incl accessories concealed run on walls/ ceiling incl MS terminal boxes fabricated with 1.6 mm thick MS sheet surface mounted/ concealed on walls with plastic laminated sheet top cover 3 mm thick fixed with cadmium plated iron screws for housing the switches, switch socket outlets, fan regulators etc., incl provision of 2.5 sq.mm PVC insulated single core multi stranded copper conductor cable as earth continuity conductor and connecting to common earth dolly, all as specified and as directed. Note for Sl Item No 2.002 to 2.006 :- (i) The earth wire for the points in the same circuit can be looped from point to point. (ii) Earth wire shall be taken inside the conduit. (iii) Cost of terminal box is deemed to be included in the item rate quoted for point wiring

Switch piano flush type single pole one way 5 Amps all as specified and as directed.

Switch socket combination 2 in 1, 3 pin 5 and 15 Amps flush type universal all as specified and as directed

Switch socket combination 2 in 1, 5 Amps flush type all as specified and as directed.

LED tube light fitting 18 watt 6000 K (4 feet long) wall mounted industrial batten type, connector block etc, complete with all acessories internally pre-wired and including connecting up twin core twisted flexible copper conductor cable all as specified and directed.

Ceiling rose, surface bakelite type 65 x 50 mm, 2 to 3 terminals all as specified and as directed

Angle holder PVC / polycarbonate type all as specified and as directed

Electronic fan regulator, stepped type, flush type all as specified and as directed.

Dismantling, greasing and spray painting of ceiling fans complete in situ with synthetic enamel paint including filling cavities with one filler coat after cleaning all dust etc. and re-fixing with downrod & clamps complete all as specified and as directed.

MCB DB, SPN 6 ways double door type 240 volts with 200 Amps rated busbar as specified and as directed.

MCB DB, TPN, 12 ways, double door vertical type, 415 volts with 200 Amps rated busbar for housing of MCCBs incoming and MCBs outgoing as specified and as directed.

MCCB, 4 pole, 415 volts, 100 Amps, 16 KA complete all as specified and as directed.

Removing of existing and provision of new MCB single pole 240 volts 5 to 40 Amps complete all as specified and as directed

Removing of existing and provision of new MCB SPN 240 volts 32 Amps complete all as specified and as directed

Removing of existing and provision of new sub main wiring 1100 volts grade multistranded copper conductors, two runs of single core 4 sq.mm along with 4 sq.mm PVC insulated single core multistranded copper conductor cable as earth continuity conductor run along with PVC conduit medium grade of suitable size all as specified and as directed. NOTE:- Two wires of 4 sq.mm and one wire of 4 sq.mm and one run of PVC conduit shall be measured as one unit.

Skyline LED 30 Watt building security light having high power LED with pressure die cast all as specified and as directed.

Bracket made out of GI tubing medium grade 40 mm bore, approx length 1.5 mtr long including MS clamps made out of MS flat iron 25 x 6 mm fixed with suitable nuts, bolts, washers etc and applying two coats of aluminum paint over a coat of red oxide primer including removing the old existing GI bracket from buildings complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick burried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5 mtr connected to galvanized earth lead wire 4 mm dia as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles,check nuts and washers etc made of galvanized iron connected to earthing test point all as shown in electrical plate No 3 of SSR Part-I 2010 and as specified or indicated and testing on completion including earth work and excavation in any type of soil PCC (1:3:6) type C1 chamber, pre cast slab 40mm thick in cement concrete (1:2:4) type B1 with 8 mm dia MS bars reinforced at 10 cm centre to centre both ways including funnel with watering pipe wire mesh and lugs, incluidng test point complete all as specified and as directed.

Excavation in trenches in hard/dense soil not exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying of cables/errection of pole etc complete all as specified and as directed.

Returning, filling in trenches includiung spreading leveling watering and well ramming in layers with hard/dense soil not exc. 25 cm thick in each layer complete as specified and as directed.

Removing the excavated material to a distance exc. 50m but n. exc. 100m and depositing where directed at a level n. exc. 1.5m above the starting point.

Sand cushioning in layers for cables in trenches / ducts for cable including consolidation complete all as specified and directed. NOTE: Punned thickness will be measured for payment purpose.

Bricks, sub class 'B' of old size 230 mm x 115 mm x 75 mm laid in trenches for cable protection all as specified and directed.

XLPE insulated, galvanised steel strip or wire armoured and PVC bedded, heavy duty, LT cable 50 sq.mm, 3.5 core, 1100 volts grade with multi stranded aluminium conductor, including cable glands, cable lugs etc., to suit the cable size, laid in trenches, or fixed along with the poles, bare or through GI pipe, laid under floors / road etc., fixed / concealed in walls / encased in GI pipe etc., jointing and testing complete all as specified and as directed.

Boring of holes under road , pavement ,hard standing by trenchless technic and nessary machine including inserting of HDPE pipe of bore 100mm dia.

GI tubing light grade 80mm with all accessories for cable protection fixed on poles/bldgs of laid in trenches incl necessary MS clamps, bolts and nuts etc all as specified and as directed

Excavation in trenches in hard/dense soil depth exc. 1.5mtr and not exc 3 mtr in depth for pole fundation etc complete all as specified and as directed.

Steel tubular swaged pole 9 meter long complete with cast iron base plate , finial tapper plug , bolts , nuts and screw as specified type 410 SP-31.

XLPE insulated, galvanised steel strip or wire armoured and PVC bedded, heavy duty, LT cable 10 sq.mm, 4 core, 1100 volts grade with multi stranded aluminium conductor, including cable glands, cable lugs etc., to suit the cable size, laid in trenches, or fixed along with the poles, bare or through GI pipe, laid under floors / road etc., fixed / concealed in walls / encased in GI pipe etc., jointing and testing complete all as specified and as directed.

Cable jointing kit for 1.1KV grade cable for out door end termination joint complete with jointing material and accessories suitable for 50 sq.mm, 3.5 core XLPE armoured aluminium conductor cable .

GI pipe light grade 40 mm dia in trenches for cable protection on pole/on wall complete all as specified and diretced.

FRP cable looping boxes with PVC sheet finish inside, including MCB SP 6 Amps 1 No, heavy duty PVC connector, 4 way terminal strip 01 no and fixed to pole including suitable size clamps, nuts and bolts complete all as specified and as directed.

Security light fitting with 1x60 Watt LED, high power LED 5700 K suitable for primary roads pressure die cast LED street lights all as per Wipro, Cat No.:- LR02-671-XXX-57-XX or techno commercially equivalent makes specified in PS all as specified and as directed.

2 runs of PVC insulated 2.5 sqmm single core multistranded copper conductor cable and one run of 2.5 sqmm copper wire as earth continuity conductor all as specified and as directed. Note: Two runs of cable and one run of earth wire shall be measured as one length.

Plain Cement Concrete, (1:4:8), type D2, using 40mm graded stone aggregate, as in foundation of poles complete all as specified and as directed

Plain Cement Concrete, (1:3:6), type C1, using 20mm graded stone aggregate, as incoping of pole, including necessary form work all as specified and as directed.

Plain Cement Concrete, (1:3:6), type C2, using 40mm graded stone aggregate as in filling and mass concrete of pole, cutting of road ,all as specified and as directed.

Modular type switch 6 Amps, one way 1 module complete all as specified and directed.

Modular type switch 16 Amps 1 way 1 module complete all as specified and directed.

Modular type socket outlet, 6 Amps,2 module complete all as specified and as directed.

Modular type socket outlet, 6/16 Amps, 2 module complete all as specified and as directed.

Modular type fan regulator, step type, 120 Watt, two module complete all as specifiedand directed.

Exhaust fan 300 mm sweep, heavy dutty 230 Volts including opening of wall and fixing the same with all necessary arrangements including louvers, flexible wire complete all as specified and directed.

Ceiling fan 1200 mm sweep five star rated including necessary down rods as per site requirement with all acessories all as pe Havells Model No ES 50 or techno commercially equivalent makes specified in PS all as specified and as directed.

Skyline LED 30 W building security light having high power LED with pressure die cast all as specified and as directed all a s per Wipro Cat No. LR02-331-XXX-57-XX or techno commercially equivalent makes specified in PS all as specified and as directed.

Bracket made out of GI tubing medium grade 40 mm bore , approx length 1.5 m long including MS clamps made out of MS flat iron 25 x 6 mm , nuts, bolts, washers etc and including before fixing applying two coats of aluminum paint over a coat of red oxide primer including removing the old existing GI bracket from bldg complete all as specified and directed.

Recess mounted LED luminaries 36 Watt including lamp complete all as per Wipro Cat No. CRCO23RO36HP65 G1 / Havells Cat No. PLUTONEO 2X2PLR34 WLED 840S or techno commercially equivalent makes specified in PS all as specified and directed.

New generation 25 Watt post top light fittings including lamp, energy saving IP-65 enviornmental friendly long life with symmetrically light distribution, spun aluminium with high power LED all as per Havells Cat No. CORAL PT 25W LED 757 PSYMTOPC or or techno commercially equivalent makes specified in PS all as specified and directed.

MCCB DB TPN 8 ways double door vertical type 415 volts with 200 Amps rated busbar for housing of MCCB incoming and MCBs outgoing as specified and as directed.

MCB DB SPN 8 way double door type 240 volts with 200 Amps rated busbar as specified and as directed.

MCCB 4 pole 415 volts 125 Amps 16 KA complete all as specified and as directed

MCB TPN 415 volts 63 Amps 16 KA complete all as specified and as directed

VIKAS CONSTRUCTIONS

Eeguchi Constructions

G K CONSTRUCTIONS