Construction of additional facilities at ITI Tura in WestGaro Hills

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive)

consisting of main "T" runner with suitably spaced joints to get required length and of size 24 x 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross 'T' of size 24 x 25 mm made of 0.30 mm thick (minimum) sheet,1200 mm long spaced between main "T" at 600 mm centre to centre to form a grid of 1200 x 600 mm and secondary cross "T" of length 600 mm and size 24 x 25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 x 600 mm panel to form grids of 600 x 600 mm and wall angle of size 24 x 24 x 0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/ making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using Gl slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5 mm dia. and 50 mm long dash fasteners, 4 mm Gl adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to lS:2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4mm c/c with centre borders of 48 mm and the side borders of 30 mm, backed with nonwoven tissue on the backside, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing

Long point wiring upto 10mts (i) With copper conductor

Wiring to a power plug as in item No.6 above with 2X4mm 2 including supplying of 15Amp 5 in 1 SS combined with continuous earth wire to a power point complete

Bill of Quantities

BOQ item no

Supplying fitting & fixing earthing with copper earth plate 600 × 600mm × 6mm thick including accessories & providing masonry enclosure with cover plate having locking arrangement & watering pipe etc with charcoal, salt set complete as required

Earth work in excavation by manual/ mechanical means (Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge. (For site preparation)

All kinds of soil

In ordinary rock

In hard rock (Blasting prohibited)

Earth work in excavation by mechanical means upto a depth of 2 m below the existing ground level for foundation, trenches of foundations, footings of columns/ walls, retaining wall, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils.

All kinds of soil (ordinary soil/ hard soil/ dense soil)

In ordinary rock (soft rock/ medium rock/ hard shale)

In hard rock (soft rock/ medium rock/ hard shale) (Blasting prohibited)

Co2 Type 4.5kgs

All kinds of soil

In ordinary rock

In hard rock (Blasting prohibited)

Disposal of surplus earth/ unserviceable material from the work site including loading and unloading complete as directed for a total of 15 km (i.e. 10 km beyond the initial lead of 5 km)

Excavated earth

Excavated rock

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered).

Upto a depth of 1.50 m

Above 1.50 m upto 3.00 m depth

Earthwork in filling (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, including breaking of clods, consolidating each layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

With available excavated earth

Implementation of Emergency Preparedness Plan, Grievance Redress Mechanism, Stakeholder Engagement activities, Traffic Management,etc.

Extra over Item for additional lift of 1.5m or part thereof for all types of soils

Sand filling in plinth in layers not exceeding 150mm in depth including breaking of clods, consolidating by watering and ramming complete as directed (maximum depth 45 cm)

SUB TOTAL

Centering and shuttering including strutting, propping etc. and removal of form for all heights complete and as directed by the Engineer-in-charge.

Shuttering for sides of plain cement concrete work in blinding concrete, plinth protection, copings, sills etc.

Foundations, footings, bases of columns, raft, grade slab etc. for mass concrete (using steel)

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. (using steel)

Suspended floors, roofs, landings, balconies and access platforms, shelves (using steel)

Lintels, beams, plinth beams, girders, bressumers and cantilevers (using steel)

Columns, Pillars, Piers, Abutments, Posts and Struts (using steel)

Stairs/ spiral staircase, (excluding landings) (using timber)

Weather shade, Chajjas, corbels etc., including edges (using timber)

Extra for additional height in centering, shuttering wherever required with adequate bracing, propping etc., including cost of de-shuttering and de-centering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured)

Implementation of Corrective Action Plan

SUB TOTAL

Part - D: DG Set

Plain cement concrete works in foundation bed for footing steps, walls, brick works etc. below plinth level as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).

1 :3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete in retaining walls etc. and all works above plinth level such as pilasters, columns, pillars, posts, struts, buttresses, parapets, coping, plain window sills, fillets, sunken floor etc.,, up to first floor level, excluding the cost of centering, shuttering and finishing

Training and Capacity Building

SUB TOTAL

Bill of Quantities for ITI-Tura (Hostel Block), West Garo Hills

Providing and laying cement concrete in retaining walls etc. and all works above plinth level such as pilasters, columns, pillars, posts, struts, buttresses, parapets, coping, plain window sills, fillets, sunken floor etc.,, up to first floor level, excluding the cost of centering, shuttering and finishing

1 :2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size)

SUB TOTAL

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per ls: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.

All works up to plinth level

All works above plinth level up to first floor level

Extra for providing richer mixes:

Providing M-30 grade concrete

Ridges plain (500-600mm)

SUB TOTAL

Supplying, fitting and fixing in position reinforcement bars up to lst floor level, conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (Rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurement for the same is required)

Thermo-Mechanically Treated bars

Providing and fixing pro-coated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per ls:277, in 240 Mpa Steel grade, 5-7microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self-drilling/ self tapping screws complete:

Providing and fixing parallel threaded couplers conforming to ls code on "Reinforcement Couplers for Mechanical Splices of Bars for Concrete Reinforcement-Specification", to reinforcement bars including threading, enlargement at connection by forging, protecting the prepared reinforcement bars and related operations as required to complete the works as per direction of Engineer in-Charge

Coupler for 16 mm diameter reinforcement bar

Coupler for 20 mm diameter reinforcement bar

Coupler for 25 mm diameter reinforcement bar

SUB TOTAL

Brick work with common burnt clay modular lst class bricks in foundation and in plinth:

In Cement Mortar 1:6 (1 cement : 6 coarse sand)

Brick work in cement mortar with first class brick in superstructure above plinth level up to first floor level in all shapes and sizes:

Cement mortar 1:6 (1 cement : 6 coarse sand)

Sub total of Enviroment Management Plan Cost: D

Half brick masonry with common burnt clay (non modular) first class bricks in superstructure above plinth level up to first floor level

Cement mortar 1:4 (1 cement :4 coarse sand)

Sub Total of Sanitary, Plumbing & Fire Fighting Cost: C

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

SUB TOTAL

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) up to plinth level with:

Cement mortar 1 :6 (1 cement: 6 coarse sand)

SUB TOTAL

Providing and fixing 18 mm thick gang saw cut, mirror polished, pre-moulded and pre-polished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade, area of slab upto 0.50 sqm (For laboratory counter tops)

Providing edge moulding to 18 mm thick marble stone counters, Vanities, etc.„ including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in Charge.

Granite work

Extra for fixing marble/ granite stone, over and above corresponding basic item, in facia and drops of width up to 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to lS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours and shades of any size as approved by Engineer-in-Charge, in walls, skirting, risers of steps and dados, over 12 mm thick bed Of cement mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Normal range

Providing polished Vitrified wall tiles of approved quality, size, shape and thickness not less than 8 mm on walls and skirting over cement mortar bed 10 mm thick in prop.1:3 (1 cement: 3 coarse sand) including cutting where necessary finished with flush pointing with adhesive or white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed.

Normal range

Tree felling

Granite Stone of approved shade

SUB TOTAL

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought trained and fixed in position with hold fast lugs or with dash fasteners of required diameter & length.

With Teak wood/ Sissu wood.

Providing and fixing ISI marked flush door shutters conforming to lS:2202 (Part I) non-decorative type, core of block board construction with frame of lst class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including lSl marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with wooden battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:

With Teak wood/ Sissu wood - 50 x 20 mm

Providing and fixing 18 mm thick,150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, lS:3087 marked, including top cover of 6 mm commercial ply wood conforming to lS:303 BWR grade, nickel plated M.S. pipe 20 mm dia (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100x40x40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Extra for using veneered particle board conforming to lS:3097 Grade I, in item of pelmet 18 mm thick 150 mm wide.

Particle board with decorative veneering on both sides

Providing and fixing teak wood lipping of size 25x3 mm in pelmet.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete:

25 mm dia

Providing & fixing decorative high pressure laminated sheet of plain/ wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to lS : 2046 Type S, including cost of adhesive of approved quality.

1.5 mm thick

SUB TOTAL

Providing and fixing in position collapsible steel shutters with vertical channels 20xl0x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia. steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered).

Providing and fixing M.S.fan clamp type I or II of 16 mm dia. M.S.bar, bent to shape with hooked ends in RCC slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars, etc. including priming coat with approved steel primer all complete.

Fixed to openings/ wooden frames with rawl plugs screws etc.

Providing and injecting approved grout in proportion recommended by the manufacturer into cracks/ honey-comb area of concrete/ masonry by suitable gun/ pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge

Stirrer mixed Acrylic Polymer of approved make @ 2% of weight of cement used) modified Cement slurry made with non-shrink compound in concrete/ BCC work

Providing and fixing bolts including nuts and washers complete.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.

M.S. Tube

SUB TOTAL

Normal range (For toilets)

General Note for Flooring :

All Stone flooring should be adequately protected with plastic sheets, POP layer till final polishing & handing over, without any extra payment.

Providing and laying damp proof course

with cement concrete in prop 1 :11/2:3 with graded stone aggregate of 10 mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

40 mm thick

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing soling with stone, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.

Stone Soling, 150 mm

Filling sunken floor with broken brick bats/ stone aggregates and sand including compacting and supplying of materials complete as specified and directed for all levels.

Brick bats

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 :4 (1 cement: 4 coarse sand).

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade Of the slabs, including rubbing and polishing complete

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre.

Providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to lS:15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600 x 600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg Of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling, grouting and finishing complete as per direction of Engineer-in-charge

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing, etc. all complete as specified and as directed by the Engineer-in-Charge. (In strips or any other approved pattern for Ramp areas)

Providing Vitrified Anti-skid Tiles of approved quality size, shape not less than 8 mm on floor, skirting over a cement mortar bed 15 mm thick of 1:3 (1 cement: 3 coarse sand) complete at all level as specified and directed.

SUB TOTAL

Providing & fixing G.I. Hexagonal chicken wire mesh of 19 size of aperture (12mm x 20 gauge) confirming to IS : 3150 at the junction of dissimilar surfaces of brick / block masonry wall and RCC column / beams and the like including necessary "U" nails / screws with cleats for fixing, overlapping, necessary scaffolding etc. complete all as per specification and as directed by the Engineer-in-charge for all heights and all locations.

PLASTERING

Providing and applying 15 mm thick cement plaster on rough side of single or half brick wall of mix: in cement mortar 1:6 (1 cement : 6 coarse sand) to interior masonry/ concrete wall surfaces

PLAIN CEMENT CONCRETE (M10)

Providing and applying 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement: 6 fine sand).

Providing and applying 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self-curing mortar of approved make as per the direction of Engineer-in-Charge.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 in or part thereof.

Providing and applying 12 mm of cement plaster finished with a floating coat of neat cement of in cement mortar 1:4 (1 cement : 4 coarse sand) to interior masonry/ concrete wall surfaces

Add for plaster drip course/groove in plastered surface or moulding to R.C.C. projections.

SUB TOTAL

Polyurethane (PU) polishing on woodwork with sprayer including sanding, wood filler complete as directed

PAINTING, OILING, POLISHING, VARNISHING WORKS

Finishing walls with Acrylic smooth exterior paint of required shade, including scaffolding:

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat Of exterior primer applied @ 2,20 kg/10 sqm)

Wall painting with acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

New work (two coats)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

New work (two or more coats)

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanized iron/ steel works

SUB TOTAL

HD-20; Circular shape 560 mm internal diameter

With borrowed earth/ stone dust carriage upto 5 km

FENCING, SITE DEVELOPMENT & MISCELLANEOUS WORKS

Providing and laying tactile tiles (for vision impaired persons as per standards) of size 300 x 300 x 9.8mm having water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 cement: 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and placing in position, 100 mm thick factory made machine batched & machine mixed precast RCC rectangular covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia. TMT bars of Fe 500 grade @ maximum 100 mm c/c on both ways, neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick,100 mm wide MS sheet duly painted over priming coat, reinforcement to be welded at edges with MS sheet and providing 2 Nos.12 mm dia. bar for hooks etc. including cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Suspended floors, roofs, landings, beams and balconies (Plan area to be measured) (For total height of 6.60 m (i.e.3.10m over and above the standard height of 3.5 m)

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 in above ground level and removal of rubbish up to a distance of 50 in outside the periphery of the area cleared.

Beyond 30 cm girth up to and including 60 cm girth

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 in and lift up to 1.5 m in all kinds of soil

Supplying chemical emulsion in sealed containers including delivery as specified.

1:3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) (For cement concrete sc

litre

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

Treatment of soil under floors using chemical emulsi

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

on @ 1 litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor:

Treatment of masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement: 2 coarse sand) to the full depth of the hole:

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia. holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing

Rectangular shape of 453 x 357mm

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia. PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS:10910, on 12 mm dia. steel bar conforming to IS:1786, having minimum cross section as 23x25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacturer's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) complete as per design.

Supplying and fixing C.I. cover without frame for manholes:

560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

SUB TOTAL

Providing and fixing in position weep holes of 75mm diameter made out of UPVC pipes of (4KSC class) of approved make, quality and length upto 500 mm as specified below, including grouting, making good the surrounding surface, cleaning etc. complete

ALUMINIUM WORK

For fixed portion; using anodized aluminium (anodized transparent or dyed to required shade according to ls:1868, minimum anodic coating of grade AC 15)

PLAIN CEMENT CONCRETE (M15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately); using anodized aluminium (anodized transparent or dyed to required shade according to ls:1868, minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door. window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge:

With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium extruded sections.

For fixed portion

SUB TOTAL

For shutters of doors, windows & ventilators

WATER PROOFING

Note: All the waterproofing treatment shall be executed through a recognized water- proofing agency approved by the Engineer-in-charge. A written guarantee on non-judicial stamp paper shall be submitted by the Contractor for a minimum period of ten years from the certified date of completion for the satisfactory performance of the entire water-proofing system.

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for underground structures as directed by Engineer-in-charge and consisting of :

(i) 1st layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound conforming to lS:2645 in the recommended proportion over the levelling course (levelling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound.

(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions.

(iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 0.008 cum/sqm thoroughly embedded in the 2nd layer.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to ls:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement: 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge:

Providing and placing in position suitable PVC water stops conforming to lS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:

Serrated with central bulb (225 mm wide, 8-11 mm thick)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying:

1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours.

2nd layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying integral ce

ment based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge over the PCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/ brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1 :5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by the Engineer-in-charge to required slope and treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing, applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1 :4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm squares, 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.

Providing & mixing approved pure acrylic based polymer modified waterproofing compound in concrete work of approved brand and quality, mixed with cement in required proportions as per manufacturer's guidelines, specifications and as directed by the Engineer-in-Charge. The product shall comply with IS: 9103 and IS: 2645. The product must be free of chlorides and shall comply with ASTM C494 Type A & D.

Note : 1) Reinforced cement concrete shall be paid separately under relevant item

All above operations to be done in order and as directed and specified by the Engineer-in-Charge.

With average thickness of 120 mm and minimum thickness of 65 mm.

SUB TOTAL

Grading roof for water proofing treatment with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Making soak pit 2.5 in diameter 3,0 metre deep with 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diamcter,1.8 in long complete as per standard design

DOOR AND WINDOW FITTINGS

Hinges

Providing and fixing lS:12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:

Providing and fixing oxidized M.S. double acting spring hinges with necessary screws etc. complete.

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge

Handles

Providing and fixing aluminium handles, lSl marked, anodized (anodic coating not less than grade AC 10 as per lS:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing bright finished brass 100 mm mortise latch and lock, lsl marked, with six levers and a pair of anodized (anodic coating not less than grade AC 10 as per ls:1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3 mm thick & 2100 mm long with SS screws etc. complete as per direction of Engineer-in-Charge

Anodized (AC 15) aluminium tubular handle bar (for glass door)

Locks & latches

Providing and fixing bright finished brass 100 mm mortise latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete

Providing and fixing Brass 100 mm mortise latch and lock with 6 levers without pair of handles (best make of approved quality) tor aluminium doors including necessary cutting and making good etc. complete

Providing and fixing 100 mm aluminium baby latch, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts, lSI marked anodized (anodic coating not less than grade AC 10 as per ls:1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

reed below floors)

Door closers, stoppers & tower bolts

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with lSI, lS:3564, embossed on the body, door weight up to 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, lSl marked, anodized (anodic coating not less than grade AC 10 as per ls:1868) transparent or dyed to required colour and shade, with necessary screws etc. complete

Twin rubber stopper

Window fittings

Providing and fixing aluminium casement stays, lSl marked, anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete.

Signages (Door mounted)

SUB TOTAL

Providing & fixing brush finished 16 SWG stainless steel stain finished (SS 304 Grade) signages of specified size, approved make and quality at all indicated locations as per approved shop drawings and as directed by the Engineer-in-charge .

Signages of 200 mm x 200mm size and make and mounted on door / wall, fixed with SS screws including all accessories etc. complete.

SUB TOTAL

Providing & fixing brush finished 16 SWG stainless steel stain finished (SS 304 Grade) signages of specified size, approved make and quality at all indicated locations as per approved shop drawings and as directed by the Engineer-in-charge .

REINFORCEMENT WORK

Neat cement punning

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smcoth complete.

With float glass panes of 4 mm thickness (weight not less than 10 kg/sqm)

ROAD WORK

Excavation in Soil with dozer with lead upto 100 m

Disposal of surplus earth/ unserviceable material from the work site including loading and unloading complete as directed for a total of 15 km (i.e. 10 km beyond the initial lead of 5 km)

Excavated earth

Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections as per Technical Specification clause 302.3.

Excavation in Ordinary Rock using Hydraulic Excavator and Tippers with disposal upto 1000 m

Plain cement concrete works in foundation bed for footing steps, walls, brick works etc. below plinth level as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).

1 :3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for all heights complete and as directed by the Engineer-in-charge.

Shuttering for sides of plain cement concrete work in blinding concrete, plinth protection, copings, sills etc.

Sand filling in plinth in layers not exceeding 150mm in depth including breaking of clods, consolidating by watering and ramming complete as directed (maximum depth 45 cm)

With borrowed earth/ stone dust carriage upto 5 km

Excavation for roadway in ordinary rock with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, transporting to embankment site with a lift upto 1.5 m and lead upto 1000 m, trimming the bottom and side slopes in accordance with the requirement of lines, grades and cross-sections as per Technical Specification Clause 302.3.5

Excavation in Hard Rock (Blasting prohibited)

Excavation for roadway in hard rock (blasting prohibited) with rock breakers including breaking rock, loading in tippers and disposal with a lift upto 1.5 m and lead upto 1000 metres, trimming bottom and side slopes in accordance with the requirement of lines, grades and cross-sections as per Technical Specification Clause 302.3.5

Subgrade

SUB TOTAL

Kerb stone for Road and Footpath

HORTICULTURE AND LANDSCAPING

Electrical Works:

Providing, laying, connection, testing & commissioning of the following sizes of 1100V grade Copper conductor armoured underground cable & overall PVC sheathed cable as per ISI code in trenches including the cost of digging of trenches, sand cushioning with laying etc. and refilling the same in layers or by supporting them in walls and all other accessories as required.

With 4 core 16 sqmm

With 4 core 10 sqmm

With 4 core 6 sqmm

With 3 core 10 sqmm

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

With 3.5 core 50 sqmm

Road markings

Diluting and injecting chemical emulsion for pre-constructional anti-termite treatment (excluding the cost of chemical emulsion):

Painting lines, dashes, arrows etc. on roads in two coats on new work with ready mixed road marking paint conforming to IS : 164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and Technical Specification Clause 1702. Assuming 100 mm width

Providing and laying 60 mm thick factory made cement concrete interlocking paver blocks of M-30 grade made by block making machine with strong vibratory compaction, of approved size. design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Sub Total of Civil Cost: A

Felling trees of the girth (measured at a height of 1 in above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.

Diluting and injecting chemical emulsion for pre-constructional anti-termite treatment (excluding the cost of chemical emulsion):

Part B: Building Electrification

Long point wiring upto 10mts (i) With copper conductor

Wiring in looping system with copper PVC cable 250/440 volt grade of size 1.5 sqmm of approved quality using PVC casing capping incluiding 5 amperes switch Indian best quality ceiling rose etc. capable to a highest point

Wiring as in item No.6 above to a Ceiling/ Exhaust Fan Point

Wiring to a power plug as in item No.6 above with 2X4mm 2 including supplying & Fitting of 15Amp 5 in 2 SS combined with continuous earth wire to a power point complete

Drawing of Main and Sub-main line with DGSD approved VIR or PVC 250/440 Volt grade in PVC casing capping complete with all

accessories.

With 2×2.5mm2 Copper Conductor

With 2X4 mm2 Copper Conductor

With 2X6 mm2 Copper Conductor

Drawing 3 phase Main Line 4 wire with DGSD approved VIR PVC cable 660 V grade in casing capping with all necessary accessories

With 4 X 6 sq. mm copper conductor

With 4 X 10 sq. mm copper conductor

Supplying & fixing of Load Kontaket Miniature Circuit Breakers (MCBs)

6 - 32 Amp. SP MCB

40 - 63 Amp. SPN MCB

40 - 63 Amp. TPN MCB

Supplying, fitting & fixing of Load Kontaket Miniature circuit breakers Double Pole (Isolator)

32 Amp DP Isolator

40 Amp DP Isolator

63 Amp DP Isolator

100 Amp DP Isolator

125 Amp DP Isolator

Supplying, fitting and fixing of Residual-current circuit Breaker with Overcurrent protection RCBOs assembled for AC applications upto 63A.

Supplying, fitting and fixing of Moulded case circuit Breaker of the following capacity

4 Poles 16 -63 Amp Capacity

4 Poles 80 -100 Amp Capacity

Supplying, fitting and fixing of SPN / TPN MCB Metal enclosure MCB Distribution box

Supplying, fitting and fixing of SPN / TPN MCB Metal Enclosure Distribution Board

12 Way (8+36) Modules

Supplying, fitting and fixing Metal box of following sizes on surface or in recess with suitable size of Phendie Lamiated sheet cover in the front including painting etc. as required.

75mm x 75mm x 60mm deep

150mm x 150mm x 60mm deep

250mm x 300mm x 100mm deep

Supplying fitting and fixing Batten LED light fitting complete with all accessories for surface or pendant mounting as per Department direction and approved

Supplying fitting and fixing LED fittings of different wattage,surface or recess or pole mounting, direct or indirect luminair square or round shape also suitable for porch lighting etc.fitted with mirror reflect or complete with all neccessary accessories.

18 watt Round

10 watt Bulk head

Supplying fitting and fixing complete polish brass bracket, 16mm dia and 23cm long with cast backplate and brass lamp holder with LED lamp.(a) with 25cm dia glass shade complete.

Supplying and fitting of ceiling fan AC operated type 220/250 volt. Complete with 3Nos of blades down rod canopy hanging shackle & regulator complete with 30mm length down rod supplied with the fan by the dealer but the extra length will be charged @ Rs25.00/ mtr

AC ceiling Fan '1400' mm sweeps

Supplying , installation testing & commissioning of self contained emergency light unit 1x3 watt double sided for wall / ceilling mounting with suspension / mounting kit, inbuilt standby battery( for 2hours backup)and battery charger etc.

1 x 3 W double sided

Supplying fitting and fixing of exhaust fan double bearing self lubricating type single phase 50Hz 250V AC operated complete with supporting frame, fan blades, nuts and bolts, fan regulator, capacitor, adjustable type lever and other petty accessories as required

Medium Duty Exhaust Fan

Providing and fixing aluminium tower bolts, ISl marked, anodized (anodic coating not less than grade AC 10 as per lS:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Supplying, fixing, connecting, testing and commissioning of calling Bell/ Bell indicator type suitable for 230 V as well as battery operated complete with all necessary accessories

Gong Bell

Ding dong Bell

Remote Bell

Supplying fitting & fixing earthing with GI earth plate 600 × 600mm × 6mm thick including accessories & providing masonry enclosure with cover plate having locking arrangement & watering pipe etc with charcoal, salt set complete as required

GI Earth Plate Electrode

Supplying and laying of 15mm × 5mm GI/Copper Strip at 0.50mts, below ground.

With 25mm×5mm copper strip

with 25mmx6mm GI strip

with 25mmx3mm GI strip

Supplying, fitting and fixing of copper/Alluminium lightning Arrestor with 5no.s finger at the top & copper base plate at the bottom complete.

FIRE EXTINGUISHER

With 3 ft high road

Providing, fixing, connecting and testing of lightning conductor (AirTermination) made of 32 mm dia GI Pipe 2 meters long with 150X180 mm dia galvanized base plate complete with all necessary accessories

CAT - 6 unarmoured UTP

SITC of External light of 70 watt LED fixture with 7 meter GI pole of single arm, including foundation, foundation bolts, nuts, MCB, internal wiring with 3R x 2.5 sqmm, conduiting etc. complete as per site requirement

Pr ltr

Short Point Wiring up to 3 mts (i)With copper conductor

Wiring as in item No.1 complete to a light plug point when fixed on same boad.

Part-C: UPS

Supply, Installation, Testing and Commissioning of following rated high performance IGBT based fully microprocessor controlled (Single phase Input & Single phase Output) online UPS system suitable for input and output parameters as per specifications. The UPS shall have Separate Galvanic Isolation Transformer Inbuilt/External K13 Copper Wound (After Static Switch) transformer. The UPS shall be provided in powder coated fan cooled enclosure painted in colour as per specifications. The UPS shall be suitable for normal, emergency, recharge, by-pass and maintenance mode including bypass arrangement. The UPS shall have a microprocessor based display and control panel. UPS shall have own batteries with 30 minute battery back-up with SMF batteries .Complete system must be provided as per specifications approved drawing and as per site requirement including inter connecting cables from battery to UPS, UPS to panel with single core copper cabling etc. UPS shall work on parallel/ hot redundancy mode, cost of supporting kit shall be included. supports for complete system as approved by the Engineer in charge complete in all respect.

Part-C: UPS / Invitor

Grand Total Cost of ITI-Tura (Placement Cell cum Academic Block)

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand Cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to ls:7231, with all fi"ngs and fixtures complete. including cutting and

White Vitreous china Orissa pattern W.C, pan of size 580x440 mm with integral type foci rests

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

With 3 core 4 sqmm

White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

With 3 core 4 sqmm

One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle level) conforming to IS:7231, with all fitting and fixtures complete.

10 ltr Capacity - white

10 ltr Capacity - coloured

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

White solid plastic seat with lid

Semirigid pipe

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

Flexibal pipe

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

Oval shape 450x350 mm (outer dimensions)

Rectangular shape 1500x450 mm

Providing and fixing soil, waste and vent pipes:

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

Long point wiring upto 10mts (i) With copper conductor

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

Supplying, loading,unloading,installation, testing & commissioning of Diesel Generating set having continuously rated of 35KVA, Silent type with acoustic enclosure, radiator cooled, 415 volts at 1500 RPM, 0.8 lagging power factor suitable for 50 HZ, 3 phase system and as per Latest amendments of MOEF and CPCB. The DG sets shall be suitable for being overloaded upto 10% of the rated capacity for 1 hour in every 12 hours and consisting of the followings: The DG set shall be suitable for above 0.8 loading factor with net output shall be 25kVA as per site conditions, with Day oil Tank,AMF Panel

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

15 mm nominal outer diameter pipe

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

SANITARY FIXTURES AND FITTINGS

Providing and fixing gun metal gate valve with C.I, wheel Of approved qilality (screwed end):

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

32 mm nominal bore.

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

70W suitable for pole dia 76mm

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

80 mm nominal bore

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

With 3 core 4 sqmm

25 mm nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end):

Vertical

Long point wiring upto 10mts (i) With copper conductor

32 mm nominal bore

Long point wiring upto 10mts (i) With copper conductor

Providing and fixing c.P. brass shower rose with 15 or 20 mm inlet:

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

, Exhaust pipe as per site requirement. Complete as required at site of work including AMC for 1 Year or as per site

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ls:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Pr LTR

Providing and fixing C.P. brass bib cock of approved quality conforming to ls:8931 :

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

20 mm nominal bore, 89 mm long, weighing not less than 88 gins

DRAINAGE

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

180xl50 mm size p type

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

Supplying and fixing c.I. cover without frame for manholes:

455x610 mm rectangular c.I. cover (light duty) the weight of the cover to be not less than 23 kg

500 mm diameter c.I. cover (medium duty) the weight of the cover to be not less than 58 kg

560 mm diameter c.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

Raising manhole cover and frame slab to required level including dismantling existing slab and making good the damage as required (Plaising depth of manhole to be paid separately):

Plectangular manhole 90x80 cm with rectangular cover 600 x 450 mm Of grade

Flectangular manhole 120x90 cm with circular cover 500 mm dia. Of grade MD -10

Flectangular manhole 120x90 cm with circular cover 560 mm dia. of grade HD - 20

WATER HARVESTING

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction Of Engineer-in charge

Supplying, filling, spreading & levelling grovels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads and lifts, all complete as per direction of Engineer-in-charge.

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

SANITARY FIXTURES AND FITTINGS

Providing and fixing gun metal non-return valve of approved quality (screwed end):

100mm dia G.I Pipe

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

50mm dia Butterfly wall

Sub Total of Eletrical Cost: B

Design and Preconstruction Phase

Regulatory Clearances/Permits like Tree Felling Permission and Compensatory Plantation

Lumpsum

Contractors Qualified Environment, Health and Safety Expert/s, PMC's and DSC's Qualified Environmental Experts,PIU and PMU level Qualified Environmental Expert

Baseline Monitoring: Ambient Air Quality

Number

Baseline Monitoring: Ambient Noise quality

Baseline Monitoring: Ground Water quality and Drinking Water

Baseline Monitoring: Surface Water quality

Baseline Monitoring: Soil Quality

Shifting of Utility (if applicable)

Construction Phase (1 Year)

Traffic management at worksite (signage, Warning Lights etc.)

Horticulture and Green Area Development

Waste and wastewater management

Monitoring: Ambient Air Quality

Monitoring: Ambient Noise quality

Monitoring: Ground Water quality and Drinking Water

Monitoring: Surface Water quality

Monitoring: Soil Quality

Rainwater Harvesting structures

Noise Barrier near school and residential areas

Restoration of construction site

Construction Phase (1 Year)

Traffic management at worksite (signage, Warning Lights etc.)

Horticulture and Green Area Development

Water sprinkling during construction

Monitoring: Ambient Air Quality

Operation Phase (1year)

Regulatory Clearances/Permits like Fire NoC, etc.

Waste and wastewater management (including installation and management of Septic tank)

Monitoring: Surface Water quality (depending on availability)

EHS audit Annually

Green area maintenance (Monitoring of Survival of trees) : Annually

Others

80mm dia Butterfly wall

Providing and fixing brass bib cock of approved quality:

Long point wiring upto 10mts (i) With copper conductor

15 mm nominal bore

Bill of Quantities

BOQ item no

Supplying fitting & fixing earthing with copper earth plate 600 × 600mm × 6mm thick including accessories & providing masonry enclosure with cover plate having locking arrangement & watering pipe etc with charcoal, salt set complete as required

Earth work in excavation by manual/ mechanical means (Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge. (For site preparation)

All kinds of soil

In ordinary rock

In hard rock (Blasting prohibited)

Earth work in excavation by mechanical means upto a depth of 2 m below the existing ground level for foundation, trenches of foundations, footings of columns/ walls, retaining wall, septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead and lifts as directed and specified for the following classification of soils.

All kinds of soil (ordinary soil/ hard soil/ dense soil)

In ordinary rock (soft rock/ medium rock/ hard shale)

In hard rock (soft rock/ medium rock/ hard shale) (Blasting prohibited)

SITC of Dome Camera as per site condition complete with all accessories 4MP

All kinds of soil

In ordinary rock

In hard rock (Blasting prohibited)

Disposal of surplus earth/ unserviceable material from the work site including loading and unloading complete as directed for a total of 15 km (i.e. 10 km beyond the initial lead of 5 km)

Excavated earth

Excavated rock

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered).

Upto a depth of 1.50 m

Above 1.50 m upto 3.00 m depth

Earthwork in filling (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, including breaking of clods, consolidating each layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

With available excavated earth

Implementation of Emergency Preparedness Plan, Grievance Redress Mechanism, Stakeholder Engagement activities, Traffic Management,etc.

Extra over Item for additional lift of 1.5m or part thereof for all types of soils

Sand filling in plinth in layers not exceeding 150mm in depth including breaking of clods, consolidating by watering and ramming complete as directed (maximum depth 45 cm)

SUB TOTAL

Centering and shuttering including strutting, propping etc. and removal of form for all heights complete and as directed by the Engineer-in-charge.

Shuttering for sides of plain cement concrete work in blinding concrete, plinth protection, copings, sills etc.

Foundations, footings, bases of columns, raft, grade slab etc. for mass concrete (using steel)

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. (using steel)

Suspended floors, roofs, landings, balconies and access platforms, shelves (using steel)

Lintels, beams, plinth beams, girders, bressumers and cantilevers (using steel)

Columns, Pillars, Piers, Abutments, Posts and Struts (using steel)

Stairs/ spiral staircase, (excluding landings) (using timber)

Weather shade, Chajjas, corbels etc., including edges (using timber)

Extra for additional height in centering, shuttering wherever required with adequate bracing, propping etc., including cost of de-shuttering and de-centering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured)

Implementation of Corrective Action Plan

SUB TOTAL

Part - D: DG Set

Plain cement concrete works in foundation bed for footing steps, walls, brick works etc. below plinth level as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately).

1 :3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete in retaining walls etc. and all works above plinth level such as pilasters, columns, pillars, posts, struts, buttresses, parapets, coping, plain window sills, fillets, sunken floor etc.,, up to first floor level, excluding the cost of centering, shuttering and finishing

Training and Capacity Building

SUB TOTAL

Bill of Quantities for ITI-Tura (Hostel Block), West Garo Hills

Providing and laying cement concrete in retaining walls etc. and all works above plinth level such as pilasters, columns, pillars, posts, struts, buttresses, parapets, coping, plain window sills, fillets, sunken floor etc.,, up to first floor level, excluding the cost of centering, shuttering and finishing

1 :2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size)

SUB TOTAL

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per ls: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.

All works up to plinth level

All works above plinth level up to first floor level

Extra for providing richer mixes:

Providing M-30 grade concrete

Ridges plain (500-600mm)

SUB TOTAL

Supplying, fitting and fixing in position reinforcement bars up to lst floor level, conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20 G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (Rates inclusive of all wastage, lappage, hooks, chairs, anchorage etc. and no measurement for the same is required)

Thermo-Mechanically Treated bars

Providing and fixing pro-coated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per ls:277, in 240 Mpa Steel grade, 5-7microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self-drilling/ self tapping screws complete:

Providing and fixing parallel threaded couplers conforming to ls code on "Reinforcement Couplers for Mechanical Splices of Bars for Concrete Reinforcement-Specification", to reinforcement bars including threading, enlargement at connection by forging, protecting the prepared reinforcement bars and related operations as required to complete the works as per direction of Engineer in-Charge

Coupler for 16 mm diameter reinforcement bar

Coupler for 20 mm diameter reinforcement bar

Coupler for 25 mm diameter reinforcement bar

SUB TOTAL

Brick work with common burnt clay modular lst class bricks in foundation and in plinth:

In Cement Mortar 1:6 (1 cement : 6 coarse sand)

Brick work in cement mortar with first class brick in superstructure above plinth level up to first floor level in all shapes and sizes:

Cement mortar 1:6 (1 cement : 6 coarse sand)

Sub total of Enviroment Management Plan Cost: D

Half brick masonry with common burnt clay (non modular) first class bricks in superstructure above plinth level up to first floor level

Cement mortar 1:4 (1 cement :4 coarse sand)

Sub Total of Sanitary, Plumbing & Fire Fighting Cost: C

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

SUB TOTAL

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement: 6 coarse sand: 12 graded stone aggregate 20 mm nominal size) up to plinth level with:

Cement mortar 1 :6 (1 cement: 6 coarse sand)

SUB TOTAL

Providing and fixing 18 mm thick gang saw cut, mirror polished, pre-moulded and pre-polished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade, area of slab upto 0.50 sqm (For laboratory counter tops)

Providing edge moulding to 18 mm thick marble stone counters, Vanities, etc.„ including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in Charge.

Granite work

Extra for fixing marble/ granite stone, over and above corresponding basic item, in facia and drops of width up to 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing Of cut edges etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to lS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours and shades of any size as approved by Engineer-in-Charge, in walls, skirting, risers of steps and dados, over 12 mm thick bed Of cement mortar 1 :3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Normal range

Providing polished Vitrified wall tiles of approved quality, size, shape and thickness not less than 8 mm on walls and skirting over cement mortar bed 10 mm thick in prop.1:3 (1 cement: 3 coarse sand) including cutting where necessary finished with flush pointing with adhesive or white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed.

Normal range

Tree felling

Granite Stone of approved shade

SUB TOTAL

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought trained and fixed in position with hold fast lugs or with dash fasteners of required diameter & length.

With Teak wood/ Sissu wood.

Providing and fixing ISI marked flush door shutters conforming to lS:2202 (Part I) non-decorative type, core of block board construction with frame of lst class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including lSl marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with wooden battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete:

With Teak wood/ Sissu wood - 50 x 20 mm

Providing and fixing 18 mm thick,150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, lS:3087 marked, including top cover of 6 mm commercial ply wood conforming to lS:303 BWR grade, nickel plated M.S. pipe 20 mm dia (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100x40x40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Extra for using veneered particle board conforming to lS:3097 Grade I, in item of pelmet 18 mm thick 150 mm wide.

Particle board with decorative veneering on both sides

Providing and fixing teak wood lipping of size 25x3 mm in pelmet.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete:

25 mm dia

Providing & fixing decorative high pressure laminated sheet of plain/ wood grain in gloss/ matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to lS : 2046 Type S, including cost of adhesive of approved quality.

1.5 mm thick

SUB TOTAL

Providing and fixing in position collapsible steel shutters with vertical channels 20xl0x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia. steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer

Grand Total Cost of ITI-Tura (Hostel Block)

Bill of Quantities for ITI-Tura (Placement Cell cum Academic Block), West Garo Hills

PLAIN CEMENT CONCRETE (M10 GRADE)

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered).

Providing and fixing M.S.fan clamp type I or II of 16 mm dia. M.S.bar, bent to shape with hooked ends in RCC slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars, etc. including priming coat with approved steel primer all complete.

Fixed to openings/ wooden frames with rawl plugs screws etc.

Providing and injecting approved grout in proportion recommended by the manufacturer into cracks/ honey-comb area of concrete/ masonry by suitable gun/ pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge

Stirrer mixed Acrylic Polymer of approved make @ 2% of weight of cement used) modified Cement slurry made with non-shrink compound in concrete/ BCC work

Providing and fixing bolts including nuts and washers complete.

PLAIN CEMENT CONCRETE (M15 GRADE)

REINFORCED CEMENT CONCRETE (M25 GRADE)

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed togcther at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements tor inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to ls:4454 - part1 and M.S. top cover of required thickness tor rolling shiitters.

SUB TOTAL

Normal range (For toilets)

General Note for Flooring :

All Stone flooring should be adequately protected with plastic sheets, POP layer till final polishing & handing over, without any extra payment.

Providing and laying damp proof course

with cement concrete in prop 1 :11/2:3 with graded stone aggregate of 10 mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacturer including curing etc. complete as directed.

40 mm thick

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing soling with stone, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete.

Stone Soling, 150 mm

Filling sunken floor with broken brick bats/ stone aggregates and sand including compacting and supplying of materials complete as specified and directed for all levels.

80xl.25 mm M.S. laths with 1.25 mm thick top cover

Brick bats

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 :4 (1 cement: 4 coarse sand).

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade Of the slabs, including rubbing and polishing complete

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to lS:15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600 x 600 mm

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg Of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling, grouting and finishing complete as per direction of Engineer-in-charge

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing, etc. all complete as specified and as directed by the Engineer-in-Charge. (In strips or any other approved pattern for Ramp areas)

Providing Vitrified Anti-skid Tiles of approved quality size, shape not less than 8 mm on floor, skirting over a cement mortar bed 15 mm thick of 1:3 (1 cement: 3 coarse sand) complete at all level as specified and directed.

SUB TOTAL

Providing & fixing G.I. Hexagonal chicken wire mesh of 19 size of aperture (12mm x 20 gauge) confirming to IS : 3150 at the junction of dissimilar surfaces of brick / block masonry wall and RCC column / beams and the like including necessary "U" nails / screws with cleats for fixing, overlapping, necessary scaffolding etc. complete all as per specification and as directed by the Engineer-in-charge for all heights and all locations.

Supplying & applying of portland cement based vermiculite cementitious fireproofing system of approved brand and quality for structural steel elements as per manufacturer's specifications and approved method statements. The product shall conform to minimum spray applied density of 350 kg/m3 as per ASTM E605 standards. The fireproofing thickness shall conform to a valid "N" series design to UL 263 (ASTM E119) standard for a limiting temperature of 538 degrees C (or 1000 degrees F) for various steel element sizes based on section factor (Hp/A or W/D). The treated steel surface shall be with no cracks, no spalling and no erosion and does not promote the corrosion of steel as per the detailed technical guide specifications. The item shall include for priming coat comprising of high solid corrosion resistant epoxy primer with a minimum DFT of 75 microns and demonstrated salt fog test performance exposure of 4 hours to ASTMB117 with no rusting,

creeping or blistering. The fire proofing vermiculate material shall meet all the necessary design and testing criteria required for minimum two hours fire rating as per NBC/BS or any other equivalent applicable code. Fireproofing shall be free of asbestos, mineral fibres, polystyrene, or other known materials which may be considered hazardous either during mixing, application, curing, or chemical release in a fire. The product shall have the manufacturer's certification that the materials to be supplied comply with the manufacturer's specifications and factory QMS certification to ISO 9001:2005. The fireproofing product shall comply to UL FuS (Follow-up Scheme) and ensure the product delivered on site shall be with UL Mark on the packaging. The item shall include for surface preparation, necessary scaffolding/ staging for all leads, heights & levels, cleaning, manufacturer's performance guarantee for a period of ten years on approved proforma etc. all complete as per manufacturer's specifications and as directed by the Engineer-in-charge.

On structural steel work

100mm dia Butterfly wall

50mm dia Non return valve

SUB TOTAL

Polyurethane (PU) polishing on woodwork with sprayer including sanding, wood filler complete as directed

Providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08% and conforming to lS:15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.

ROOFING

SUB TOTAL

HD-20; Circular shape 560 mm internal diameter

PLASTERING

Providing and applying 15 mm thick cement plaster on rough side of single or half brick wall of mix: in cement mortar 1:6 (1 cement : 6 coarse sand) to interior masonry/ concrete wall surfaces

PLAIN CEMENT CONCRETE (M10)

Providing and applying 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement: 6 fine sand).

Providing and applying 6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self-curing mortar of approved make as per the direction of Engineer-in-Charge.

per bag of 50 kg cement

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 in or part thereof.

Add for plaster drip course/groove in plastered surface or moulding to R.C.C. projections.

Providing and applying 12 mm of cement plaster finished with a floating coat of neat cement of in cement mortar 1:4 (1 cement : 4 coarse sand) to interior masonry/ concrete wall surfaces

SUB TOTAL

Providing and fixing in position weep holes of 75mm diameter made out of UPVC pipes of (4KSC class) of approved make, quality and length upto 500 mm as specified below, including grouting, making good the surrounding surface, cleaning etc. complete

PAINTING, OILING, POLISHING, VARNISHING WORKS

Finishing walls with Acrylic smooth exterior paint of required shade, including scaffolding:

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat Of exterior primer applied @ 2,20 kg/10 sqm)

Wall painting with acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

New work (two coats)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:

New work (two or more coats)

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanized iron/ steel works

SUB TOTAL

For shutters of doors, windows & ventilators

With borrowed earth/ stone dust carriage upto 5 km

FENCING, SITE DEVELOPMENT & MISCELLANEOUS WORKS

Providing and laying tactile tiles (for vision impaired persons as per standards) of size 300 x 300 x 9.8mm having water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 cement: 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and placing in position, 100 mm thick factory made machine batched & machine mixed precast RCC rectangular covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia. TMT bars of Fe 500 grade @ maximum 100 mm c/c on both ways, neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick,100 mm wide MS sheet duly painted over priming coat, reinforcement to be welded at edges with MS sheet and providing 2 Nos.12 mm dia. bar for hooks etc. including cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Beyond 30 cm girth up to and including 60 cm girth

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 in and lift up to 1.5 m in all kinds of soil

Supplying chemical emulsion in sealed containers including delivery as specified.

1:3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) (For cement concrete sc

litre

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

Treatment of soil under floors using chemical emulsi

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 ltr/ Rm including drilling and plugging holes etc.:

on @ 1 litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floor:

Treatment of masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement: 2 coarse sand) to the full depth of the hole:

Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia. holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing

Rectangular shape of 453 x 357mm

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia. PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS:10910, on 12 mm dia. steel bar conforming to IS:1786, having minimum cross section as 23x25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacturer's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) complete as per design.

Supplying and fixing C.I. cover without frame for manholes:

560 mm diameter C.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

SUB TOTAL

Grading roof for water proofing treatment with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

ALUMINIUM WORK

For fixed portion; using anodized aluminium (anodized transparent or dyed to required shade according to ls:1868, minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door. window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge:

With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium extruded sections.

PLAIN CEMENT CONCRETE (M15)

For fixed portion

SUB TOTAL

Providing & fixing brush finished 16 SWG stainless steel stain finished (SS 304 Grade) signages of specified size, approved make and quality at all indicated locations as per approved shop drawings and as directed by the Engineer-in-charge .

WATER PROOFING

Note: All the waterproofing treatment shall be executed through a recognized water- proofing agency approved by the Engineer-in-charge. A written guarantee on non-judicial stamp paper shall be submitted by the Contractor for a minimum period of ten years from the certified date of completion for the satisfactory performance of the entire water-proofing system.

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for underground structures as directed by Engineer-in-charge and consisting of :

(i) 1st layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound conforming to lS:2645 in the recommended proportion over the levelling course (levelling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound.

(ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions.

(iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 0.008 cum/sqm thoroughly embedded in the 2nd layer.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to ls:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement: 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge:

Providing and placing in position suitable PVC water stops conforming to lS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:

Serrated with central bulb (225 mm wide, 8-11 mm thick)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying:

1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours.

2nd layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying integral ce

ment based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge over the PCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/ brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1 :5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by the Engineer-in-charge to required slope and treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls and slabs.

(c) After two days of proper curing, applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1 :4 (1 cement: 4 coarse sand) admixed with water proofing compound conforming to lS:2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm squares, 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.

Providing & mixing approved pure acrylic based polymer modified waterproofing compound in concrete work of approved brand and quality, mixed with cement in required proportions as per manufacturer's guidelines, specifications and as directed by the Engineer-in-Charge. The product shall comply with IS: 9103 and IS: 2645. The product must be free of chlorides and shall comply with ASTM C494 Type A & D.

Note : 1) Reinforced cement concrete shall be paid separately under relevant item

All above operations to be done in order and as directed and specified by the Engineer-in-Charge.

With average thickness of 120 mm and minimum thickness of 65 mm.

SUB TOTAL

Providing, fabricating, assembling & installing at all levels and in required architectural profile, single skinned pre-coated galvalume sheet roofing system with profiled pre-coated zincalume sheets of approved brand, colour, shade, size & quality & 0.5 mm thickness (TCT) including all accessories, necessary scaffolding / staging for all leads, heights and levels as per approved shop drawings, manufacturer's guidelines &, specifications etc. all as per directions and to the satisfaction of the Engineer-in-charge.& comprising of the following layers :

Making soak pit 2.5 in diameter 3,0 metre deep with 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diamcter,1.8 in long complete as per standard design

DOOR AND WINDOW FITTINGS

Hinges

Providing and fixing lS:12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:

Providing and fixing oxidized M.S. double acting spring hinges with necessary screws etc. complete.

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/ top hung windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge

Handles

Providing and fixing bright finished brass 100 mm mortise latch and lock, lsl marked, with six levers and a pair of anodized (anodic coating not less than grade AC 10 as per ls:1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Anodized (AC 15) aluminium tubular handle bar (for glass door)

Locks & latches

Providing and fixing bright finished brass 100 mm mortise latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete

Providing and fixing Brass 100 mm mortise latch and lock with 6 levers without pair of handles (best make of approved quality) tor aluminium doors including necessary cutting and making good etc. complete

Providing and fixing 100 mm aluminium baby latch, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete.

Providing and fixing aluminium sliding door bolts, lSI marked anodized (anodic coating not less than grade AC 10 as per ls:1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

reed below floors)

Door closers, stoppers & tower bolts

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with lSI, lS:3564, embossed on the body, door weight up to 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium hanging floor door stopper, lSl marked, anodized (anodic coating not less than grade AC 10 as per ls:1868) transparent or dyed to required colour and shade, with necessary screws etc. complete

Twin rubber stopper

Window fittings

Providing and fixing aluminium casement stays, lSl marked, anodized (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete.

Signages (Door mounted)

SUB TOTAL

i) Top Layer – Shall comprise of trapezoidal profiled galvalume steel sheet of 1015 mm effective width and nominal 28.5 mm deep ribs with subtle square fluting in the five pans at nominal 203mm center to center. The end rib shall be designed for anti- capillary action, to avoid any seepage of water through the lateral overlap. The base material used shall be as per AS / NZS 2728 Type 4 and with nominal 0.45 mm Base Metal Thickness (0.50 mm TCT) of Hi-Strength with minimum 550 MPa yield strength, AZ150 (Min. 150 g/m2 total of both sides)

Signages of 200 mm x 200mm size and make and mounted on door / wall, fixed with SS screws including all accessories etc. complete.

SUB TOTAL

Kerb stone for Road and Footpath

HORTICULTURE AND LANDSCAPING

Electrical Works:

Providing, laying, connection, testing & commissioning of the following sizes of 1100V grade Copper conductor armoured underground cable & overall PVC sheathed cable as per ISI code in trenches including the cost of digging of trenches, sand cushioning with laying etc. and refilling the same in layers or by supporting them in walls and all other accessories as required.

With 4 core 16 sqmm

With 4 core 10 sqmm

With 4 core 6 sqmm

With 3 core 10 sqmm

Providing and fixing 75 mm high, 50 mm deep and 18 mm thick stone slab table rubbed, edges rounded and polished, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.

With 3.5 core 50 sqmm

Road markings

Diluting and injecting chemical emulsion for pre-constructional anti-termite treatment (excluding the cost of chemical emulsion):

Painting lines, dashes, arrows etc. on roads in two coats on new work with ready mixed road marking paint conforming to IS : 164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and Technical Specification Clause 1702. Assuming 100 mm width

Providing and laying 60 mm thick factory made cement concrete interlocking paver blocks of M-30 grade made by block making machine with strong vibratory compaction, of approved size. design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Sub Total of Civil Cost: A

Felling trees of the girth (measured at a height of 1 in above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.

Diluting and injecting chemical emulsion for pre-constructional anti-termite treatment (excluding the cost of chemical emulsion):

Part B: Building Electrification

5.5 KVA UPS described as above with 30 minute battery Backup

ABC Powder Type 5kgs

Wiring in looping system with copper PVC cable 250/440 volt grade of size 1.5 sqmm of approved quality using PVC casing capping incluiding 5 amperes switch Indian best quality ceiling rose etc. capable to a highest point

Wiring as in item No.6 above to a Ceiling/ Exhaust Fan Point

Wiring to a power plug as in item No.6 above with 2X4mm 2 including supplying & Fitting of 15Amp 5 in 2 SS combined with continuous earth wire to a power point complete

Drawing of Main and Sub-main line with DGSD approved VIR or PVC 250/440 Volt grade in PVC casing capping complete with all

accessories.

With 2×2.5mm2 Copper Conductor

With 2X4 mm2 Copper Conductor

With 2X6 mm2 Copper Conductor

Drawing 3 phase Main Line 4 wire with DGSD approved VIR PVC cable 660 V grade in casing capping with all necessary accessories

With 4 X 6 sq. mm copper conductor

With 4 X 10 sq. mm copper conductor

Supplying & fixing of Load Kontaket Miniature Circuit Breakers (MCBs)

6 - 32 Amp. SP MCB

40 - 63 Amp. SPN MCB

40 - 63 Amp. TPN MCB

Supplying, fitting & fixing of Load Kontaket Miniature circuit breakers Double Pole (Isolator)

32 Amp DP Isolator

40 Amp DP Isolator

63 Amp DP Isolator

100 Amp DP Isolator

125 Amp DP Isolator

Supplying, fitting and fixing of Residual-current circuit Breaker with Overcurrent protection RCBOs assembled for AC applications upto 63A.

Supplying, fitting and fixing of Moulded case circuit Breaker of the following capacity

4 Poles 16 -63 Amp Capacity

4 Poles 80 -100 Amp Capacity

Supplying, fitting and fixing of SPN / TPN MCB Metal enclosure MCB Distribution box

Supplying, fitting and fixing of SPN / TPN MCB Metal Enclosure Distribution Board

12 Way (8+36) Modules

Supplying, fitting and fixing Metal box of following sizes on surface or in recess with suitable size of Phendie Lamiated sheet cover in the front including painting etc. as required.

75mm x 75mm x 60mm deep

150mm x 150mm x 60mm deep

250mm x 300mm x 100mm deep

Supplying fitting and fixing Batten LED light fitting complete with all accessories for surface or pendant mounting as per Department direction and approved

Supplying fitting and fixing LED fittings of different wattage,surface or recess or pole mounting, direct or indirect luminair square or round shape also suitable for porch lighting etc.fitted with mirror reflect or complete with all neccessary accessories.

18 watt Round

10 watt Bulk head

Supplying fitting and fixing complete polish brass bracket, 16mm dia and 23cm long with cast backplate and brass lamp holder with LED lamp.(a) with 25cm dia glass shade complete.

Supplying and fitting of ceiling fan AC operated type 220/250 volt. Complete with 3Nos of blades down rod canopy hanging shackle & regulator complete with 30mm length down rod supplied with the fan by the dealer but the extra length will be charged @ Rs25.00/ mtr

AC ceiling Fan '1400' mm sweeps

Supplying , installation testing & commissioning of self contained emergency light unit 1x3 watt double sided for wall / ceilling mounting with suspension / mounting kit, inbuilt standby battery( for 2hours backup)and battery charger etc.

1 x 3 W double sided

Supplying fitting and fixing of exhaust fan double bearing self lubricating type single phase 50Hz 250V AC operated complete with supporting frame, fan blades, nuts and bolts, fan regulator, capacitor, adjustable type lever and other petty accessories as required

Medium Duty Exhaust Fan

Providing and fixing aluminium tower bolts, ISl marked, anodized (anodic coating not less than grade AC 10 as per lS:1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Supplying, fixing, connecting, testing and commissioning of calling Bell/ Bell indicator type suitable for 230 V as well as battery operated complete with all necessary accessories

Gong Bell

Ding dong Bell

Remote Bell

Supplying fitting & fixing earthing with GI earth plate 600 × 600mm × 6mm thick including accessories & providing masonry enclosure with cover plate having locking arrangement & watering pipe etc with charcoal, salt set complete as required

GI Earth Plate Electrode

Supplying and laying of 15mm × 5mm GI/Copper Strip at 0.50mts, below ground.

With 25mm×5mm copper strip

with 25mmx6mm GI strip

with 25mmx3mm GI strip

Supplying, fitting and fixing of copper/Alluminium lightning Arrestor with 5no.s finger at the top & copper base plate at the bottom complete.

FIRE EXTINGUISHER

With 3 ft high road

Providing, fixing, connecting and testing of lightning conductor (AirTermination) made of 32 mm dia GI Pipe 2 meters long with 150X180 mm dia galvanized base plate complete with all necessary accessories

Supplying fitting and fixing of LAN (Computer Cables)

hot dip metallic coating of 55% Aluminum- Zinc to AS 1397 (Zincalume steel) and lead free super durable polyester quality paint top coat with inorganic pigment. The total paint coat thickness shall be nominal 35 μm, comprising of nominal 20 μm exterior coat on top surface and nominal 5 μm backer polyester coat on reverse surface over nominal 5 μm primer coat on both surfaces in approved shade. The feed material shall have coil manufacturer’s product details marked at regular intervals. Note : Structural steel Work including supporting frames, purlins and its painting shall be measured and paid separately under relevant item.

SITC of External light of 70 watt LED fixture with 7 meter GI pole of single arm, including foundation, foundation bolts, nuts, MCB, internal wiring with 3R x 2.5 sqmm, conduiting etc. complete as per site requirement

Pr ltr

Wiring as in item No.1 complete to a light plug point when fixed on same boad.

Part-C: UPS

Supply, Installation, Testing and Commissioning of following rated high performance IGBT based fully microprocessor controlled (Single phase Input & Single phase Output) online UPS system suitable for input and output parameters as per specifications. The UPS shall have Separate Galvanic Isolation Transformer Inbuilt/External K13 Copper Wound (After Static Switch) transformer. The UPS shall be provided in powder coated fan cooled enclosure painted in colour as per specifications. The UPS shall be suitable for normal, emergency, recharge, by-pass and maintenance mode including bypass arrangement. The UPS shall have a microprocessor based display and control panel. UPS shall have own batteries with 30 minute battery back-up with SMF batteries .Complete system must be provided as per specifications approved drawing and as per site requirement including inter connecting cables from battery to UPS, UPS to panel with single core copper cabling etc. UPS shall work on parallel/ hot redundancy mode, cost of supporting kit shall be included. supports for complete system as approved by the Engineer in charge complete in all respect.

Part-C: UPS / Invitor

Grand Total Cost of ITI-Tura (Placement Cell cum Academic Block)

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand Cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to ls:7231, with all fi"ngs and fixtures complete. including cutting and

White Vitreous china Orissa pattern W.C, pan of size 580x440 mm with integral type foci rests

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

With 3 core 4 sqmm

White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

With 3 core 4 sqmm

One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle level) conforming to IS:7231, with all fitting and fixtures complete.

10 ltr Capacity - white

10 ltr Capacity - coloured

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

White solid plastic seat with lid

Semirigid pipe

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

Flexibal pipe

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

Oval shape 450x350 mm (outer dimensions)

Rectangular shape 1500x450 mm

Providing and fixing soil, waste and vent pipes:

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

Long point wiring upto 10mts (i) With copper conductor

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

Supplying, loading,unloading,installation, testing & commissioning of Diesel Generating set having continuously rated of 35KVA, Silent type with acoustic enclosure, radiator cooled, 415 volts at 1500 RPM, 0.8 lagging power factor suitable for 50 HZ, 3 phase system and as per Latest amendments of MOEF and CPCB. The DG sets shall be suitable for being overloaded upto 10% of the rated capacity for 1 hour in every 12 hours and consisting of the followings: The DG set shall be suitable for above 0.8 loading factor with net output shall be 25kVA as per site conditions, with Day oil Tank,AMF Panel

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

15 mm nominal outer diameter pipe

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

SANITARY FIXTURES AND FITTINGS

Providing and fixing gun metal gate valve with C.I, wheel Of approved qilality (screwed end):

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

32 mm nominal bore.

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

70W suitable for pole dia 76mm

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

White solid plastic seat with lid

Coloured (other then black & white ) solid plastic seat with lid

80 mm nominal bore

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

With 3 core 4 sqmm

25 mm nominal bore

Providing and fixing gun metal non-return valve of approved quality (screwed end):

Vertical

Long point wiring upto 10mts (i) With copper conductor

32 mm nominal bore

Long point wiring upto 10mts (i) With copper conductor

Providing and fixing c.P. brass shower rose with 15 or 20 mm inlet:

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

, Exhaust pipe as per site requirement. Complete as required at site of work including AMC for 1 Year or as per site

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ls:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Pr LTR

Providing and fixing C.P. brass bib cock of approved quality conforming to ls:8931 :

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

20 mm nominal bore, 89 mm long, weighing not less than 88 gins

DRAINAGE

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

180xl50 mm size p type

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

Supplying and fixing c.I. cover without frame for manholes:

455x610 mm rectangular c.I. cover (light duty) the weight of the cover to be not less than 23 kg

500 mm diameter c.I. cover (medium duty) the weight of the cover to be not less than 58 kg

560 mm diameter c.I. cover (heavy duty) the weight of the cover to be not less than 108 kg

Raising manhole cover and frame slab to required level including dismantling existing slab and making good the damage as required (Plaising depth of manhole to be paid separately):

Plectangular manhole 90x80 cm with rectangular cover 600 x 450 mm Of grade

Flectangular manhole 120x90 cm with circular cover 500 mm dia. Of grade MD -10

Flectangular manhole 120x90 cm with circular cover 560 mm dia. of grade HD - 20

WATER HARVESTING

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction Of Engineer-in charge

Supplying, filling, spreading & levelling grovels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads and lifts, all complete as per direction of Engineer-in-charge.

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

70W suitable for pole dia 76mm

SANITARY FIXTURES AND FITTINGS

Providing and fixing gun metal non-return valve of approved quality (screwed end):

100mm dia G.I Pipe

Aesthetically designed led post top with aluminium enclosure, powered with high power leds as light source and die casted heat sink exhibits classic victorian look with symmetrical light distribution and excellent heat dissipation for long life.

50mm dia Butterfly wall

CEILING WORK