General Maintenance/Up-Keeping of Govt. residential quarters, PWD office complex, PWD Dak Bunkglow Kathua for the year 2020-21 upto ending of March 2021

Amount

Providing & fixing wash basin with C.I./M.S. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting & making good the walls wherever required(Hindware/Cera/Parryware or eqivalvalent make) White Vitreous China wash basin 630 x450mm with a single 15mm C.P. brass pillar taps complete job.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. (Hindware/Cera/Parryware or eqivalvalent make)

Providing and fixing white vitreous china water closet squatting pan (Indian type) Orrisa pattern size 580 x 440 mm (Hindware/Cera/Parryware or eqivalvalent make)complete job.

Providing & fixing white vitreous china pedestal type (European type/ wash down type) water closet pan (Hindware/Cera/Parryware or eqivalvalent make)complete job.

Providing and fixing PVC low level flushing cistern with manually controlled device (handle level) conforming to IS: 7231 with all fittings and fixtures complete.10 litre capacity-White complete job.(Hindware/Cera/Parryware or eqivalvalent make)

Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fitting complete semi rigid pipe 32 mm dia

Providing & fixing Salem Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S 13983 with CI bracket and stainless steel plug 40 mm including painting the fitting & bracket cutting and making good the walls wherever required. Kitchen sink without drain 610 x 510 mm with bowl depth 200 mm

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350mm and 340 x 410 x 265mm sizes respectively with automatic flushing cistern with CI/MS brackets standard size of G.I. flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete including painting of fitting and brackets, cutting & making goods the walls & floors wherever required. One urinal basin with 5 litre P.V.C. automatic flushing of approved quality

Providing and placing on terrace (at all floor levels ) polythylene Water Storage Tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for intlet, outlet and overflow pipes but without fitting and the base support for tank (Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license )

Providing and fixing 600 x 450 beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing & fixing unplasticised P.V.C. connection pipe with brass union 30 cm length 15mm nominal bore

Providing & fixing C.P. brass shower rose with 15 mm or 20 mm inlet 150mm diameter complete job.

Providing and fixing C.P hand spray with lever control (health faucet) and flexible hose 1 mtr long connection with C.P holder for hand spray complete in all respects as per direction of Engineer-In-charge

Providing and fixing Polyethelene-Aiuminium-Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to IS:15450 U.V. stablised with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature upto 80°C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) eg. Elbows, tees, reducers, couplers and connectors etc. with clamps at one metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the Engineer-in-charge. (Concealed work including cutting chases and making good the wall etc.)

1620 (20mm OD) pipe

2025 (25mm OD) pipe

2532 (32mm OD) pipe

Providing and fixing Polyethelene-Aiuminium-Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to 15:15450 U.V. stabilised with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature upto 80°Cincluding all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e"g. Elbows, tees, reducers,couplers and connectors etc. with clamps at one metre spacing. This includes testing of joints complete as per direction of the Engineer-in-charge Internal work exposed on wall.

1620 (20mm OD) pipe

2025 (25mm OD) pipe

2532 (32mm OD) pipe

Providing and fixing PPR pipes complete with PPR fittings and clamps, including cutting and making good the walls etc.Internal Work-Exposed on wall.

40 mm dia

32 mm dia

25 mm dia

Providing and fixing PPR pipes complete with PPR fittings and clamps, including cutting and making good the walls etc.(Concealed work including cutting chases and making good the wall etc.)

32 mm dia

25 mm dia

Providing & fixing G.I. pipes complete with G.I. fitting and clamps including cutting and making good the walls etc.Internal Work-Exposed on wall

15mm nominal bore Medium

20mm nominal bore Medium

25mm nominal bore Medium

Providing & fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc complete

15mm nominal bore Medium

20mm nominal bore Medium

25mm nominal bore Medium

Providing and fixing PVC pipes including jointing with seal ring (Finolex/Supreme/Prince) of pressure @ 4kg/cm2

75mm dia

110 mm dia

150 mm dia

Providing and fixing PVC moulded fittings/accessories for PVC pipes including jointing with seal ring complete (Finolex/Supreme/Prince) of pressure @ 4kg/cm2

75mm dia Plain bend

110 mm dia Plain bend

Providing and fixing C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved conforming to IS standards and weighing not less than 810 gms 15 mm dia nominal bore

Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved for conforming to IS : 8931 15mm nominal bore

Providing & fixing ball valve brass of approved quailty

15mm nominal bore

20mm nominal bore

25mm nominal bore

Supplying of Following Sanitary and Water Supply fittings:-

Inner face of approved quality

Disk face of approved quality

Jet of approved quality

Pillar Cock brass of approved quality

G.I Elbow 15mm of approved quality

G.I Elbow 20mm of approved quality

G.I Elbow 25mm of approved quality

G.I Socket 15mm of approved quality

G.I Socket 20mm of approved quality

G.I Socket 25mm of approved quality

G.I Tee 15mm of approved quality

G.I Tee 20mm of approved quality

G.I Tee 25mm of approved quality

G.I Reducer 15mmx 20mm of approved quality

G.I Reducer 25mmx 20mm of approved quality

G.I Reducer 15mmx 25mm of approved quality

G.I Elbow 15mmx20mm of approved quality

G.I Elbow 20mmx25mm of approved quality

G.I. Elbow 25mmx15mm of approved quality

G.I. Nipple 15x 50mm of approved quality

G.I. Nipple 15x 100mm of approved quality

G.I. Nipple 15x150mm of approved quality

G.I. Nipple 20 x 50mm of approved quality

G.I. Nipple 20x 100mm of approved quality

G.I. Nipple 20x 150mm of approved quality

G.I. Nipple 25x50mm of approved quality

G.I. Nipple 25x100mm of approved quality

G.I. Nipple 25x150mm of approved quality

White Cement 1 Kg of approved quality

Cistern Syphon of approved quality

Cistern Handle of approved quality

Cistern Vassel of approved quality

W.C. Seat Cover White/Coloured of approved quality

C.P. Nipple of approved quality

C.P. Grating of approved quality

C.P. Cup of approved quality

Towel Rod of approved quality

Towel Ring of approved quality

PVC Collar 75mm,100mm of approved quality

P.V.C Floor Trap of approved quality

P.V.C Tee of approved quality

G.I Check Valve of approved quality

P.V.C Cistern ball Cock of approved quality

Float Valve brass of approved quality

Tank Nipple of approved quality 25 mm , 20 mm

Waste Coupling of approved quality

C.P Soap Dish of approved quality

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc complete

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc complete

Providing & fixing aluminum sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to req. colour or shade with nuts & screws etc. complete:

Providing and fixing aluminium hanging floor door stopper ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: Twin rubber stopper

Door closer Spring Type of approved quality

Door Closer Hydraulic of approved quality

Renewing Glass panes and refixing existing wooden fillets Glass Panes weighing 10 kg/ sqm

Renewing Glass panes, with Putty & Nails wherever necessary float Glass Panes of thickness 4 mm

Butt Hinges 3" of approved quality

Butt Hinges 4" of approved quality

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material in cement mortar, all leads & lifts.

Demolishing cement concrete 1 : 3 : 6 or richer mix manually/ by mechanical means including disposal of material, all leads & lifts.

Demolishing RCC work manually /by mechanical means including stacking of steel bars and disposal of unserviceable material ,all leads & lifts.

Demolishing mud phaska in terracing and disposal of material including all leads & lifts.

Demolishing brick tile covering in terracing including stacking of serviceable material & disposal of unserviceable material including all leads & lifts.

Painting top of roofs with bitumen of approved quality at 17 kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm incl. cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete with residual type petroleum bitumen of penetration 80/100

10 cm thick mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa at 35 kg/cum of earth and gobri leaping with mix 1 : 1 ( 1 clay : 1 cow dung) and covered with flat tile bricks of class designation 100 grouted with cement mortar 1:3 mixed with 2% of integral water proofing compound by weight of cement & finished neat with hand moulded F.P.S. brick tiles incl. all leads, lifts & carriage of material by MT/ H.L.

Providing & laying 400 micron thick transparent Poly Vinyl Chloride sheet on the roof under mud phaska cutting placing complete job.

Making Khurras 45 x 45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 ( 1 cement : 2 Coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1 m x 1m x 400 micron, finished with 12 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges, making and finishing the outlet complete incl. all leads, lifts & carriage of material by MT/ H.L.

Providing gola 75 x 75 mm in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 stone aggregate 10mm down gauge) including finishing with cement mortar 1:3 ( 1 cement : 3 fine sand) as per standard design in 75 x 75 mm deep chase incl. all leads, lifts & carriage of material by M.T / H.L.

Regarding terracing of mud phaska covered with tiles or bricks, in cement by dismantling tiles or bricks, removing mud plaster preparing the surface of mud phaska to proper slope, relaying plaster gobri leaping and tiles and bricks, grouted in cement mortar 1:3 (1 cement :3 fine sand ) including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded) including all leads, lifts & carriage of material by MT / H.L.

Taking out doors, windows,windows and clerestory window shutters (steel or wood) of area of 3 square metres and below including stacking of material, all leads and lifts.

Dismantling old plaster or skirting, raking out joints & cleaning the surface for plaster including disposal of rubbish to the dumping ground with all leads & lifts.

Dismantling tile work for thickness of tiles 10 mm to 25 mm in floors and walls laid in cement mortar including stacking material, all leads & lifts.

Dismantling wooden trellis work excluding frames but including stacking the serviceable material including all leads & lifts.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking of area 3 sqm and below ,all leads & lifts.

Dismantling of flushing cistern of all types ( C.I /PVC/Vitreous china) including stacking of useful materials near the site and disposal of unserviceable materials incl. all leads, lifts & carriage of material by MT/H. L.

Dismentling C.I. or Asbestos rain water pipes of 100 mm dia pipes with fittings and clamps including stacking the material , all leads & lifts.

Removing mortar from brick work in cement mortar and cleaning bricks including stacking of material, all leads & lifts ( stacks of cleaned bricks shall be measured).

Earth work excavation in all kind of soil by manual means in trenches for foundations, drains, pipes, cables etc. (Not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, depth upto 1.5m incl. disposal/filling of excavated earth all leads & lifts complete.

Providing & laying in position cement concrete 1:5:10 (cement : 5 coarse sand : 10 graded crushed stone aggregate 40 mm nominal size) of specified grade excl. the cost of centring & shuttering incl. all leads, lifts & carriage of material by MT/ H.L.- All work upto plinth level.

Providing and laying in position cement concrete 1 : 4 :8 ( 1 cement : 4 coarse sand : 8 graded crushed stone aggregate 40 mm nominal size) of specified grade excluding the cost of centring and shuttering including all leads, lifts and carriage of material by MT / H.L.-All work upto plinth level.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level. 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size ) including all leads, lifts and carriage of material by MT / H.L

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level. 1 : 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20 mm nominal size ) including all leads, lifts and carriage of material by MT / H.L

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level. 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size ) including all leads, lifts and carriage of material by MT / H.L

Providing and laying damp proof course 40 mm thick with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size) including all leads, lifts and carriage of material by MT/H.L.

Providing and laying damp proof course 50 mm thick with cement concrete 1 : 2 : 4 ( 1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size) including all leads, lifts and carriage of material by MT / H.L.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth including all shapes, leads, lifts and carriage of material by MT / H.L. in cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work in superstructure above plinth level upto floor V level (By manual means) incl. all leads, lifts and carriage of material by M.T. H.L.

Half brick masonry with bricks of class designation 75 in foundations and plinth in cement mortar 1:4 ( 1 cement :4 coarse sand) including all leads, lifts and carriage of material by MT / H.L.

Extra for half brick masonry in superstructure above plinth level upto floor V level including all leads, lifts and carriage of material by M.T. H.L.

12mm cement plaster of mix 1:4 (1 cement : 4 fine sand) including drip course/groove all leads, lifts and carriage of material by MT / H.L.

15mm cement plaster on rough side of single or half brick wall of mix 1:6 (1 cement : 6 fine sand) including drip course/groove all leads, lifts and carriage of material by MT / H.L.

Repairs to plaster of thickness 12 mm to 20 mm with cement mortar 1:4 (1 cement : 4 fine sand) in patches of area 2.5 sq. metres & under including cutting the patch in proper shape ranking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead.

Making plinth protection 50 mm thick of cement concrete 1:3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed & consolidated & grouted with fine sand including finishing the top smooth. Crushed aggregate including all leads, lifts and carriage of material by MT/H.L.

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15º landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 Graded crushed stone aggregate 20mm nominal size) including all leads, lifts and carriage of material by MT / H.L.

Reinforced cement concrete work in walls (any thickness) , including attached pilasters, buttresses, plinth and string courses, fillets,columns, pillars, piers, abutments, posts and struts, etc. upto floor V level excluding cost of centring, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand: 3 graded crushed stone aggregate 20 mm nominal size) incl. all leads, lifts and carriage of material by MT/H.L.

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete Thermo Mechanically Treated bars /Cold twisted bars including all leads, lifts and carriage of material by MT / H.L.

Centring and shuttering including strutting propping etc and removal of form work for

Foundations, footings, bases of columns etc. for mass concrete

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform.

Edges of slabs and breaks in floors and walls under 20 cms wide.

Raking out joints in lime or cement mortar and preparing the surface for repainting or replastering including disposal of rubbish to the dumping ground with all leads and lifts.

Flush pointing with cement mortar 1:3 ( 1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska with F.P.S. brick tiles

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought framed & fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or with dash fasteners shall be paid for separately)

Sal Wood

2nd Class Deodar Wood

Providing and fixing 35 mm thick Wire Gauze shutters using galvanised M.S. wire gauge of average width for aperture 1.4 mm in both direction with wire of dia. 0.63 mm for doors, windows and clerestory windows with hinges & necessary screws. ISI marked M.S. pressed bright finished butt hinges with necessary screws of required size. Second Class deodar wood.

Providing and fixing 35mm thick glazed shutters of Second class deodar wood for doors, windows and clerestory windows using 10 kg/ sqm (4 mm thick) float glass panes including black enameled ISI marked M.S. butt hinges bright finished of required size with necessary screws.

Providing and fixing 35 mm thick panelled or panelled and glazed shutters of Second class deodar wood for door, windows and clerestory windows including ISI marked black enameled M.S.butt Hinges with necessary screws excluding Panelling which shall be paid for separately , all complete as per direction of Engineer-in-Charge.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick , Particle Board 12 mm thick plain particle board flat pressed, three layer or graded wood particle board medium density grade IS: 3087 marked.

Providing and fixing fly proof galvanised M.S. wire gauge to windows and clerestory windows using galvanised M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete.With 2nd class teak wood beading 62 x 19 mm

Providing 40x 5 mm flat iron hold fast 40cm long incl. fixing to frame with 10mm diameter bolts nuts and wooden plugs with embeddings in cement concrete blocks 30 x 10 x15 cm 1:3:6 mix (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size including all leads, lifts and carriage of material by MT / H.L.

Providing and fixing gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen plateform,vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement:4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curring moulding and polishing to edge to give high gloss finish etc. complete at all levels Granite of any colour and shape(Area of slab upto 0.50 sqm) 16 mm thick

Extra for providing edge molding to 18 mm thick marble stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer- in -Charge. for granite work

Extra for providing opening of required size and shape for wash basins/ kitchen sink platform, vanity counters and similar location in marble/ stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% & confirming to IS: 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1 : 4 (1 cement : 4 coarse sand) including grouting the joints with white cement & matching pigments etc. complete size of tile 60 cm x 60 cm including all leads, lifts and carriage of material by MT / H.L.

Providing and fixing Ceramic glazed floor tiles 300 x 300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as White, Ivory, Grey, Fume Red, Brown laid on 20 mm thick bed of Cement Mortar 1 : 4 (1 cement : 4 coarse sand) including ; pointing the joints with white cement and matching pigment etc. complete.

Providing and fixing Ist quality ceramic glazed tiles conforming to IS : 13753 of minimum thickness 5 mm of approved make like NITCO, ORIENT, SOMANY KAJARIA, or equivalent make in all colour, shades except begundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. including all leads, lifts and carriage of material by MT / H.L.

Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) . Medium shade using 50% white cement and 50% ordinary cement.

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with1:2:4 mix ( 1 cement :2 coarse sand 4 graded stone aggregate 20mm nominal size),foundation concrete 1:4:8 mix (1 cement 4 coarsesand :8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement :3 coarse sand ) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cememnt : 2 coasre sand :4 graded stone aggragate 20mm nominal size ) finished with a floating coat of neat cement complete as per standard design. Inside size 90 x 80 cm and 45 cm deep including providing and fixing in position precast RCC manhole cover & frame of required shape and approved quanlity LD-2.5 rectangular shape 600 x 450 mm internal dimensions . With F.P.S bricks with class designation 75 & with crushed stone aggregate including all leads, lifts and carriage of material by M.T/ H.L.

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In granting, frames, guard bar, ladders railing, brackets, gates & similar works.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing & staircase railing and similar work including applying a priming coat of approved steel primer. G.I.pipes 40 mm nominal bore(class B)

Providing and fixing in position collapsible steel shutters with vertical channels 20 x 10 x 2 mm and braced with flat iron diagonals 20 x 5 mm size with top and bottom rail of T-iron 40 x 40 x 6 mm with 40 mm dia, steel pulleys complete with bolts, nuts locking arrangement, stoppers, handles including applying a priming coat of approved steel primer.

Providing and fixing 1 mm thick M.S. steel door with frame of 40 x 40 x 6 mm angle iron and 3mm M.S. gusset plates at the junction and corners , all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6 mm for diagonal braces and central cross piece.

Providing and fixing M.S. grills of required pattern in frames of windows etc with M.S. flats, square or round bars etc all complete

Fixed to openings/ wooden frames with Rawl plugs screws etc.

Fixed to steel windows by welding.

Providing and fixing aluminum work for doors, windows ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia and size including necessary filling up of gaps at junctions i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, milted and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing/paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge( glazing, paneling and dash fasteners to be paid for separately.)

For fixed portion anodized aluminum (anodized transparent or dyed to required shade according to IS : 1868 minimum anodic coating of grade AC 15)

For fixed portion Powder coated aluminum ( minimum thickness of powder coated 50 microns)

For shutters of doors, windows & ventilators including providing and fixings hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required( Fittings shall be paid for separately).

Anodised aluminum ( anodized transparent or dyed to required shade according to IS : 1868, minimum anodic coating of grade AC 15)

Powder coated aluminum (minimum thickness of powder coated 50

Providing and fixing glazing in aluminum door, window, ventilators shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.( Cost. Of aluminum snap beading shall be paid in basic item) With floating glass panes of 4.0 mm thickness ( weight not less than 10.00 kg/sqm)

Providing and Fixing of ACP Sheet of good quality

Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws@ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment)

Providing and fixing 100 mm brass locks (best make of approved quality)for aluminium doors including necessary cutting and making good etc complete.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo em,possed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing & cover plates with brass pivot" & single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc.including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts & bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. complete job.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets. 25mm dia (heavy type).

Providing and Fixing of CGI Sheet of Powder Coated good quality

Providing and Fixing of PVC Panelling including cutting jointing, fixing etc complete job of good quality

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats ) over & including priming coat with cement primer.

Distempering with oil bound washable distemper of approved brand & manufacture to give an even shade. Old work (one or more coats)

Wall painting with plastic emulsion paint of approved brand and manufature to give an even shade. Two or more coats on new work.

Wall painting with plastic emulsion paint of approved brand and manufature to give an even shade. Two or more coats on old work.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.One or more coats on old work.

Painting with synthetic enamel paint of approved brand brand manufacture to give an even shade. Two or more coats on new steel work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.One or more coats on old steel work.

Painting with synthetic enamel paint of approved brand brand manufacture to give an even shade. Two or more coats on new work

Providing and applying White Cement based Putty of average thickness 2 mm of approved brand & manufacture, over the plastered wall surface to prepare the surface even & smooth complete.

Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture on wood work ( hard & soft wood)

Finishing walls with water proofing cement paint of required shade:Old work ( one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litres/10 sqm complete

Finishing wall with water proofing cement paint of required shade - New work (two or More coats) applied @ 3.84 kg/10 sqm

Finishing wall with acrylic smooth exterior paint with required shade on New work (two or more coats applied) @ 1.67 litre/10 sqm over & including base Coat of water proofing cement paint applied @ 2.20 kg/10 sqm.

Finishing walls with Acrylic smooth\h exterior paint of required shade Old work ( two or more coats applied @ 1.67 litres/10 sqm on existing cement paint surface)

Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface .Water thinable Cement primer

Color washing such as green blue or buff to give an even. New work ( two or more coats) with a base coat of white washing with lime.

White washing with lime to give an even shade. New work (three or more coats)

Labour Charges for Carpentor/Plumber or equavailent skilled type

Labour Charges for Mazdoor/Helper

Rajesh Kumar

M/S NARESH KUMAR