16EECBSNLCDBGL202425

Amount

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :

25 mm dia (heavy type)

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378)

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378)

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378)

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378)

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/ nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge.

Providing and fixing cup board shutters 25mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked exterior grade (Grade l Type ll) having one side decorative lamination and other side balancing lamination including IInd class teak wood lipping of 25mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges complete as per direction of the Engineer-in-Charge

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete :

New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and of required shade and colour complete to give and even shade.

Old work (one or more coats)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work.

French spirit polishing :

One or more coats on old work.

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface).

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-harge.

With cement mortar 1:4 (1 cement : 4 fine sand).

Renewing glass panes, with wooden fillets wherever necessary:

Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm).

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe 32 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length 15 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:

15 mm nominal bore.

Providing and fixing PTMT bib cock of approved quality and colour.

15mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT stop cock of approved quality and colour.

15 mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms.

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.

15 mm nominal bore with 45 cm length.

Providing and fixing CP Brass waste coupling of size 32mm to 40mm dia. for kitchen sink / wash basin , Complete as per the directions of Engineer-in charge. Rate inclusive of removal of worn out waste coupling.

Providing and fixing two in one tap including fittings of approved make etc. complete as per the directions of Engineer-in-Charge. Cost includes removal of non-funtional/worn-out 2 -in- 1 tap.

Providing and fixing 15 mm Heath faucet of C.P brass head and P.V.C connection pipe of approved make etc. complete as per the directions of Engineer-in-Charge. Cost includes removal of non-funtional/worn-out health faucet.

Providing and fixing 15mm C.P Brass pillar taps of approved quality conforming to IS. Standard and weight not less than 650 grm . also credit of serviceable materials

15 mm nominal bore

Providing and fixing stainless steel jali with or without hole for waste pipe for covering existing floor/nahani trap

100mm dia.

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm all complete.

With available beading

Easening of wooden doors/windows of any size and thickness by removing the doors /windows shutters making necessary repairs like plaining the edges as required so as to ensure smooth functional operation of the door/window and replacing the M.S.butt hinges wherever required etc,. all complete as directed by the Engineer-in-charge.

Door shutter

Window shutter

Providing and fixing mosquito proof mesh of approved make, netlon or equivalent with necessary velcro and fixing to the existing frame with necessary adhesive all complete as directed by Engineer-in-Charge

Providing necessary repair and easening of M.S.Gate of size 3.65X1.10 metre by taking out the shutter (either by cutting/ burning the hinges using gas welding machine at site or by removing the shutter after removing the hinges as the case may be)and re-aligning the same for easy operation complete as per the directions of Engineer-in-Charge.

Clearing of weeds and cleaning of entire external portion and terrace of E-1 staff quarters by removing dry leaves, vegetation debris and other deposited / accumulated materials etc including disposal of rubbish to dumping ground up to a distance of 50m outside the periphery of building etc. complete as per the direction of the Engineer-in- charge.

Cleaning of entire internal portion of E-1 staff quarters with approved soap solution and mopping of floors and cleaning of dados and flooring of toilet & kitchen including cleaning of wash basin, water closet etc. by applying suitable cleaning agent / chemical of approved quality including removal of stains and making clean & neat the tile surfaces as directed by the E.I.C.(Cost included removal of all the accumulated waste materials, cobwebs ,dirt and dust) complete as per the direction of Engineer-in-charge.

Providing general Pest control treatment for the entire E-1 staff quarters by using gel and spray treatment with a warranty of 4 months all complete as directed by the Engineer-in-charge.

Credit for old dismantled/unserviceable material received from dismantling as and where condition (cost includes the dismantling of the materials): -

Old bib cock/Stop Cock /pillar cock (Cost includes dismantling of the materials)

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading in the dumping grounds etc. all complete as directed by the Engineer-in-charge.