SPL REPAIR TO BLDGS NOS P1 TO P6 AT TARN TARAN UNDER GE AMRTISAR

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings not excceding 15cm thickness (above or below ground level) complete all as specified and directed.

Demolition of reinforced cement concrete as in any description and in any position complete all as specified and directed.

Reinforced Cement Concrete type B1 1:1.5:3 (M20) (nominal mix ) (using 20 mm graded stone aggregate) in Beams, cantilevers, lintels etc.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhanges similar items for rough finished surface all as specified & directed.

Material and Labour , TMT bars 10mm dia and over cut to length, bent to shape required including bending, cranking etc and binding with and including MS wire (annealed) not less than 0.9mm dia, complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete complete all as specified and directed.

Material and Labour , vitrified ceramic tiles dark shade 08 to 10mm thick (square/ rectangular) polished, area of each tile n. exc. 0.36 sqm laid in floors etc. set & jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in cement mortar (1:6) including necessary cutting as per site requirement complete all as specified and directed.

Ditto as items No 07 above but as in skirting over rendering 10mm thick in cement mortor 1:4 .

Material and Labour , non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.11 sqm but n exc 0.18sqm laid in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement complete all as specified and directed.

Material and Labour , glazed ceramic coloured tiles 450mm x 350mm x 7mm thick on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed.

Material and Labour ceramic coloured exterior elevated tiles 450mm x 350mm x 7mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed.

Material and Labour , 50mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge

Demolition brickwork or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Material and Labour , for brick work with sub class ‘B’ old size bricks straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and directed.

All as per item above but except bricks. (Old serviceable bricks retrieved from demolition of brick work shall be re-used after cleaning).

All as per item above but except bricks in cement mortar (1:4). (Old serviceable bricks retrieved from demolition of brick work shall be re-used after cleaning).

Taking down cement plaster of any description on brick or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Material and Labour , rendering 12 mm thick on brick work or concrete surface in cement mortar (1:6) finished fair and even complete complete all as specified and directed.

Material and Labour , rendering 15mm thick on brick work or concrete surface in cement mortar (1:4) finishedfair and even complete complete all as specified and directed.

Material and Labour for complete removal of existing treat andapplying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces.

Material and Labour complete removal of existing treatment on wall and applying two coats of oil bound distemper over one coat of 3mm Birla wall care putty complete all as specified and directed.

Material and Labour preparing newly plastered or pointed surface of wall and applying two coats of distemper oil emulsion over a coat of Chalk whiting,on plastered surfaces, preparatory to distempering complete all as specified & directed.

Material and Labour for Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces incl preparation of old decorated surface.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50sqm but not exceeding 4.00sqm each and removing from site complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50sqm each and removing from site complete all as specified and directed.

Taking down shutter and removing from site of any description size but exc 1 sqm and n.exc 2 sqm complete all as specified and directed.

Supply and fixing in repair door closer hydraulically regulated, (Alminium die cast body) designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed, complete all as specified and directed.

Supply and fixing Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed make-Godrej, complete all as specified and directed.

Supply and fixing Anodised aluminium frame for doors,windows,ventilators,side hunge one or more rebates including necessary jointing cleats,glazing clips, ruber neoprene packing anodised aluminium snap beading screw Tee etc section for weighing not less than 1.4 kg/RM complete all as specified and directed

Supply and fixing Anodised aluminium door shutters powder coated (minimum thickness of powder coating shall not be less than 50 micron), aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified Note : Each panel shall be measured separetely. Glass pane shall be measured and paid separetely.

Supply and fixing Providing and fixing powder coated(Min thickness of powder coating shall be 50 micron) aluminum windows shutter of size min 18mmx50mm for sliding type windows of standard tubular sections of approved make having glazed panels or glazed and gauzed panels of appropriate size running on seperate tracks in the channel conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth,rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. All the panels shall be of appropriate size having overlaps as required and including all required beadings, clips, rollers, rubber gaskets, cleats,complete and powder coating in approved shade and colour. Note:- Each panel shall be measured separetely. Glass pane and wire mesh shall be measured and paid separetely.

Supply and fixing Anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with CP brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixinf approved anodised aluminium standard section around the opening, all complete as per requirements and direction of Engr-in-charge.

Supply and fixing Sheet glass, 5.5mm thick ordinary quality, in squares,exceeding 0.50 sqm in each pane including rubber packing and aluminium beading with and incl solar control film 25 Micron reflective type sticked to glass panes as per instructions of manufacturer complete all as specified and directed

Supply and fixing figured glass, 5 mm thick ordinary quality, in squares Not ,exceeding 0.50 sqm in each pane including rubber packing and aluminium beading with and incl solar control film 25 Micron reflective type sticked to glass panes as per instructions of manufacturer complete all as specified and directed

Supply and fixing 10mm thick PVC insulation panels with EPS stuck to 1mm printed PVC sheet suitably placed in aluminium door complete all as specified

Supply and fixing Brass mortice lock, 4 levers, verticle type, size 100 mm, complete all as specified and directed.

Supply and fixing, aluminium handles anodised cast type 125mm long allcomplete all as specified and directed.

Supply and fixing, aluminium anodised barrel tower bolt of extruded section 150mm long all as specified & directed by Engineer-in- charge.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

Supply and fixing factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed..

Supply and fixing 100mm long butt hinges mild steel medium weight cold rolled complete all as specified and directed. .

Supply and fixing Sheet 4.0 mm thick frosted glass, squares exc 0.5 sq. m each pane, complete all as specified and directed.

Taking down steel water tubes of size 15mm bore and connection including cleaning for refixing or removal to store complete all as specified and directed. .

Taking down steel water tubes of size 20mm bore and connection including cleaning for refixing or removal to store complete all as specified and directed. .

Supply & fixing, steel water tubes of size 15mm bore (medium grade) galvanised with all fittings and fixed complete to walls and ceiling or laid in floors/ concealed in walls allcomplete all as specified and directed.

Supply & fixing, steel water tubes of size 20mm bore (medium grade) galvanised with all fittings and fixed complete to walls and ceiling or laid in floors/ concealed in walls complete all as specified and directed. .

Re-fixing old steel water tubes of size 15mm bore in new/ old location using new fittings fixed complete to walls and ceiling or laid in floors/ concealed in walls complete all as specified and directed. .

Re-fixing old steel water tubes of size 20mm bore in new/ old location using new fittings fixed complete to walls and ceiling or laid in floors/ concealed in walls complete all as specified and directed. .

Dismantling PVC water storage tank of capacity exc 500 litre but n. exc 1000 litre and removing from site complete all as specified and directed.

Supply & fixing, rotational moulded polyethylene water storage tank of capacity 1000 litres (cylindrical vertical double layered with closed top) hoisted and fixed in position as per specified SSR part-I complete all as specified and directed. .

Supply and fixing in repair ball valve 20mm dia high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of brass ferrule complete all as specified and directed.

Supply & fixing in repair stop valve cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or brass ferrule 20mm bore complete all as specified and directed..

Supply and fixing PVC valve less, syphonic action type low level flushing cistern of capacity 10 Ltrs with inlet, ball valve, float and handle and fixed to EWC on existing brackets, fixed in repairs.

Supply and fixing in replacement vitreous china wash down water closet pan (pedestal pattern) white with trap including connection to existing out joint pipe, flushing pipe or cistern, antisyphonage pipe, including making good to floor etc complete all as specified and directed.

Supply and fixing in repair plastic water closet seat white closed pattern with flat botom and cover mild steel chromium plated or aluminium plated or aluminished hinging device complete all as specified and directed.

Material and Labour , 75mm dia cast iron floor trap with grating including jointing to waste pipe with run lead joint and embedded in cement concrete (1:2:4) type B-1 using graded stone aggregate complete all as specified and directed.

Supply and fixing in repairs 15mm bore Bib taps with flange chromium, plated cast copper alloy, fancy type with cruttch or butterfly handle screwed down screwed for iron pipe or for brass ferrule.

Supply and fixing in repair vitreous china washbasin, white, flat back, size 550 x 400mm, including brackets & incl 32mm bore waste fitting brass, CP for glazed ware basin etc with long screwed shanks and fly-nuts flange end bedded in red lead cement and other end fixed including pedastal for washbasin complete all as specified.

Supply and fixing in repairs pillar taps cast copper alloy 15mm bore with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and fix health faucet (hand spray) chromium plated fancy type with 1 metre long PVC flexible pipe 15mm bore covered with chromium plated flexible tube connected to 15mm bore iron pipe incl holder for holding faucet fixed to wall with screws complete all as specified and directed.

Supply and fixing, soap dish fixed to walls with chromium plated brass screw complete all as specified and directed.

Supply and fixing, toilet paper holder of CP fixed to wall with chromium plated brass screw complete all as specified and directed..

Supply & fixing in repairs chromium plated stop valve concealed type with long shank, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for unions suitable for size 15mm bore complete all as specified and directed. .

Supply & fixing in repair stop valve/angle valve fancy type brass CP screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or brass ferrule 15mm bore complete all as specified and directed..

Supply & fixing, PVC connection 15mm size 600mm long with PTMT nuts complete all as specified and directed..

Supply & fixing in repair brass chromium plated tubular towel rail , 20mm dia D-type, 60cm long between flanges complete all as specified and directed.

Supply and fixing in repair brass CP wall mixer with bend pipe for overhead screwed down for 15mm iron pipe complete all as specified and directed.

Supply and fixing in repair chromium plated shower rose 125mm size with or without swivel joints including fixing to 15mm bore pipe complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/ slabs/ blankets any thickness including cover fillets complete all as specified and directed.

Material and Labour for Providing and fixing Gypsum board 12 mm thick Seamless calcum silicate in ceiling made out of 1800x1200 size board of siliceous and calcareous material reinforced with fixed with screw , GI frame work for seameless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws as 450mm centre to centr/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre andas per manufacturers instructions incl preparation of new surfaces & applying two coat of OBD on ceiling over chalk whitening complete all as specified and directed.

Supply and fixing in reapair 25mm dia stainless steel Curtain rods/ rails, with brackets, stops, rollers, finials, 1 pair of decorative knobs for each curtain rod etc complete all as specified and directed.

Dismantling of brick tiles single layers on roof, jointed and grouted / pointed in cement mortar including cleaning serviceable tiles and stacking properly for re-use, disposal of unserviceable tiles and debris /rubbish from site complete all as specified and directed.

Demoliton of mud in roof any thickness including mud plastering and removing debries of the premises where directed complete all as specified and directed.

Material and labour PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in roof kerbs, sloping padding and finishing the surface even and smooth (without using extra cement) complete all as specified and directed.

Material and labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm includingcleaning surfaces etc complete all as specified and directed.

Material & Labour for APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( Wt not less than 150 gms /sqm ) laid on bituminous surfaces by forced application over entire roof area, sunken portion with overlapping 100mm to eiher side complete all specified.

Material and labour for 40 mm thick brick tiles laid over and including 15mm thick bedding layer in cement mortar 1:6 and jointed, grouted and flush pointing as work proceed in CM 1:3 complete all as specified.

All as per Srl item above here-in-before but except tiles.Note : (i) Serviceable brick tiles obtained from shall be reused.

Dismantling of PVC pipe of 75/100mm dia fixed with cement joint complete all as specified and directed.

Supply and fixing PVC (SWR) 110mm dia mtr pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Supply and fixing PVC (SWR) 110mm dia mtr bends any radius complete all as specified and directed.

Supply and fixing PVC (SWR) 100mm junction single,(Single T) equal or unequal complete all as specified and directed.

Supply and fixing PVC (SWR) 100mm junction double, (double T) equal or unequal complete all as specified and directed.

Supply and fixing PVC (SWR) 75mm junction single,(Single T) equal or unequal complete all as specified and directed.

Supply and fixing 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors ccomplete all as specified and directed.

Material and Labour PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description in any position complete all as specified & directed.

Dismantling timber scantling 40 sqcm and over in section in any position complete all as specified and directed.

Material and Labour , roof trusses framed, framed purlins, crane gantries, rails and fastenings (beams, tee, angle, channel or flat sections) including distance pieces conforming to Fe 410-W Gde E-250 complete all as specified.

Dismantling asbestos cement (corrugated, semi corrugated etc.) sheets in roof covering complete all as specified and directed.

Supply and fixing, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete complete all as specified and directed.

Supply and fixing, pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified.

Material and Labour for preparation of new steel and iron surfaces of any description, over 10 Cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide premier.

All as per above item but single coat on old steel surfaces incl preparation.

Excavation in trenches n. exc 1.5 m wide for foundations, pipe line etc. and not exceeding 1.5 m deep and getting out in soft/ loose soil complete all as specified and directed..

Material and Labour for precast cement concrete 1:1.5:3 type A-1 using 20mm graded aggete as in cover slabs (for manholes etc.) including necessary form work and set in cement mortar 1:6 all as per specified and directed.

Demolition and breaking up 150mm bore drain pipes (salt glazed stoneware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

Supply and fixing for Reinforced concrete pipes 150 mm bore , class NP3, laid and jointed complete with collars complete all as specified and directed.

Material and Labour for Cement concrete type C2 (1 : 3 : 6) using 40mm graded stone aggregate as in concrete bed to SGSW/RCC drain pipe 150mm internal dia in any depth including packing under, and haunching against the sides of pipes after they are laid and tested all as specified.

Material and Labour for Plain cement concretetype C-2, 1:3:6 using 40 mm graded stone aggregate as in foundation of drain, complete all as specified.

Material and Labour for Brick work work with sub claas B bricks straight or curved on plan exc 6m mean radius built in C M (1 : 4) all as per spcified and directed.

Material and Labour for PCC type B1 1:2:4 using 20mm graded stone aggregate as in surface channels and drain complete all as specified and directed.

Material and Labour for PCC type B0 (1 : 2 : 4) using 12.5mm graded stone aggregate as in Manhole / drain coping including necessary form work complete all as specified and directed.

Material and Labour for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:3 with using water proofing compound and finished even and smooth without using extra cement complete all as specified and directed. (Waterproofing compound measure and paid separately)

Material and Labour for steel TMT bars, 6 to 8 mm dia, cut to length, bent to required shape including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (aanealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed..

Removal of surplus spoil to a distance n.exc 50 m and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified and directed..

Material and Labour for Plain cement concretetype C-2, 1:3:6 using 40 mm graded stone aggregate as in foundation of drain, complete all as specified.

Extra for forming fair finished drain orchannel 40 cm inner girth in cementconcrete, using ex- tra cement, includingforms, moulds, mi- tred/stopped ends etc.

Material and Labour Brick work with sub class ‘B’ brick in cm 1:4 straight or curved on plan to any radius in half brick thick wall and flush pointing as the work proceeds with same mortar.

Material and Labour for brick work with sub class 'B' bricks (Old size brick) Straight or curved on plan exc 6mtr mean radius built in cement mortar 1:4 and external face of brick work pointed flush in the same mortar as the work proceeds, complete all

Material and Labour for Plain cement concretetype B-0, 1:2:4 using 12.5 mm graded stone aggregate as in surface channels and benching to drains complete all as specified.

Material and Labour for Flush pointing to brick walls in cement and sand mortar (1:4) completes all as specified.

Supply and fixing Mild steel TMT bar 10mm dia and above cut to length, bent to shape rquired including cranling , bending spirally for hooping for column , hooking ends and binding with mild steel wire not less than 0.9mm dia as specified.

Material and Labour pre cast reinforced cement concrete (1:2:4) B-1 Type using 20mm graded stone aggregate as in manhole cover and set in cement mortar (1:4) including necessary form work, complete all as specified

Material and Labour for Chequered cement concrete tile 20cmx20cmx25mm thick with grey pigment cement and pigment,set and jointed over 20 mm screed bed in CM 1:6 and pointed in neat cement slurry in floor complete as directed.

Material and Labour for 100 mm thick PCC 1:4:8 type D-2(40 mm graded stone agg) in sub base coarse complete

Material and Labour for Providing, cement concrete 1:2:4 type B-1(20 mm graded stone agg) in roof kerbs or mud stops, rounded or chamfered on edges , in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, kerbs , and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Material and Labour Septic tank of 50 users incld escavation in ordinary soil, PCC foundation, brick work in CM (1:4), RCC main hole cover, vent shaft and sludge chambers extra complete all as per specified.

Material and Labour Soakage well 2.4mtr dia x 3.0mtr depth,exccavation in ordinary soil, PCC in founbdation, Honey combed and soild Bk work in CM (1:4), RCC slab,filling with Bk bats complete all as per specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials and making good disturbed surfaces of walls, floors, etc.complete all as directedNOTE: Cost of unserviceable materials will be charged from the contractor against Schedule of Credit.

Taking down carefully existing serviceable Ceiling fan/Wall mounted fan, ceiling cable end, etc., removing the fan for keeping in safe custody, hanging the ceiling fan with down rod after rewiring including clamps, hooks, holdfasteners etc and connecting up, including making electric connection from ceiling rose or connector to fan complete all as directed

Taking down carefully existing serviceable exhaust fan, ceiling cable end, etc., removing the fan for keeping in safe custody, fixing the exhaust fan after rewiring and connecting up, including making electric connection from ceiling rose or connector to fan complete all as directed

Taking down carefully Split type AC of any capacity by disconnecting from the either terminals, ceiling cable end, etc., including all fittings and fixtures by unscrewing, removing the AC & deposit to store yard, making good to disturbed surface of wall complete as directed by Engr-in-Charge

Material and Labour for point wiring complete with 1.5 sqmm single core PVC insulated sheathed multi-stranded, copper conductor FRLS grade cable of 1100 volts grade conforming to IS:694 drawn through existing metallic/rigid PVC concealed conduit, medium grade, ISI marked, not less than 20mm bore with conduit accessories concealed on wall and ceiling/roof etc, with provn for fixing modular metal flush boxes not less than 1.0 mm thick of suitable modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, sheathed, 1100 volt grade,multistranded single core green colour copper conductor for earth continuity connected to earth dolly complete all as directed. (a) Fan point/ exhaust fan point / one light point / bell/ buzzer controlled by one switch/ bell push.

(b) One socket outet point 5 amps on the same board.

(c) One socket outet point 5 amps on the independent board.

All as Ser item 126 here in before but with 2.5 sq mm wire and earth wire of 2.5 sq mm for 3 Pin 15 Amp modular type socket outlet.

Material and Labour for point wiring complete with 1.5 sqmm single core PVC insulated sheathed multi-stranded, copper conductor FRLS grade cable of 1100 volts grade conforming to IS:694 drawn through and including non metalic rigid new PVC conduit, medium grade, ISI marked, not less than 20mm bore with conduit accessories concealed on wall and ceiling/roof etc, with provn for fixing modular metal flush boxes not less than 1.0 mm thick of suitable modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, sheathed, 1100 volt grade,multistranded single core green colour copper conductor for earth continuity connected to earth dolly complete all as directed. (a) One light point/Bell/Fan point controlled by one switch.

(b) One 3 pin 5 Amps socket outlet on independent board.

(c) One 5 Amps outlet point on same board with other switches/sockets

All as per ser item No 130 here in above but point wiring with 2.5 Sqmm FRLS cable and 2.5 sqmm cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board.(i) The wiring shall be done in proper colour coding using red, yellow and blue for phase, black for nuetral and green for earth wire.(ii) Modular metal flush boxes concealed in wall with suitable cover plate for mounting switch, sockets, regulator etc. and cost of cutting chases & making good as existing to disturbed surface with cement mortar, if required any shall be deemed to included in the quoted rates.(iii) Modular fittings/fixtures such as switch, socket, regulator, etc., shall be measured and paid separately as under relevant item.

Supply and fixing modular switch 1 way 6A, 240 volts, 1 module complete all as specified and directed

Supply and fixing modular socket, 6A, 240 volts, 2/3 pin combined 2 module, flush type all as specified and directed

Supply and fixing modular switch 1 way 16A, 240 volts, 1 module complete all as specified and directed

Supply and fixing modular socket, 6A/16A, 240 volts, 2/3 pin combined 2 module flush type all as specified and directed

Supply and fixing modular fan step regulator, 2 module, 240 Volts, 50 Hz, suitable for ceiling fan all as directed

Supply and fixing ceiling rose surface PVC/Polycarbonate, isolated body with face Bakelite 65 x 50 mm three terminal, 240 volts, AC single phase complete all as specified

Supply and fixing steel metal enclosure single pole & neutral with a 2 pin and earth plug and socket complete with one single pole MCB SP 20 Amp, 240 volts complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC, 6500K, decorative box type with driver, double sided connection, LED tube light connecting up with 3 core flexible copper conductor cable (1.0 mm² size/core) from ceiling rose complete all as specified and directed.

Supply and fixing PLUTO NEO LED luminaire 600mm x 600mm, 2X2 36/40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply and fixing Air fresh fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, single phase, 1200 RPM, Copper winding of sweep 300 mm complete fixed/grouted to wall with suitable bolts, nuts etc., and connecting up with & including 3 core flexible copper conductor cable (1.0 mm² size/core) from ceiling rose to exhaust fan and writing MES No. including cutting hole suitable for fixing exhaust fan complete all as specified and directed

Supply and fixing heavy duty exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, single phase, 1200 RPM, Copper winding of sweep 350 mm complete fixed/grouted to wall with suitable bolts, nuts etc., and connecting up with & including 3 core flexible copper conductor cable (1.0 mm² size/core) from ceiling rose to exhaust fan and writing MES No. including cutting hole suitable for fixing exhaust fan complete all as specified and directed

Supply and Laying in trenches/drawn through pipes or in road crossings/paths/drains/ ducts/floors/along poles/equipments etc., of LT cable under ground, heavy duty, armoured, XLPE insulated with multi-stranded aluminium conductor cable conforming to IS-7098 Part-I (1998), 1100 Volts grade of 70 Sqmm 3½ core nominal cross sectional area including necessary double compression copper gland and connecting up using suitable size aluminium lugs testing, incl taking down old unsv one from site complete all as specified and directedNOTE: Excavation & earthwork will be measured and paid separately

Supply and Laying in trenches/drawn through pipes or in road crossings/paths/drains/ ducts/floors/along poles/equipments etc., of LT cable under ground, heavy duty, armoured, XLPE insulated with multi-stranded aluminium conductor cable conforming to IS-7098 Part-I (1998), 1100 Volts grade of 35 Sqmm 3½ core nominal cross sectional area including necessary double compression copper gland and connecting up using suitable size aluminium lugs testing, incl taking down old unsv one from site complete all as specified and directedNOTE: Excavation & earthwork will be measured and paid separately

Supply & laying double wall corrugated (DWC) high density poly ethylene (HDPE) of size 63 mm dia including all necessary fittings, PN-4 rating, pressure 6 Kgf/cm², conforming to IS-16205 (Part-24) with high ring stiffness & cursh resistance capacity, etc., laid in trench for protection of submersible flat cable complete all as directed.

Excavating in trenches not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for foundation for erection of poles, stays, laying cables, stays etc and getting out in soft/loose soil and in road cutting complete all as specified and directed

Returning, filling in excavated material/soil including spreading, leveling, watering and well ramming in layers n exc 25cm in soil complete all as specified and directed

Removing excavated material/surplus soil not exceeding 50 meters and depositing where directed at a level not exceeding 1.5 meter above starting point

Supply and fixing lamp holder, PVC / polycarbonate type insulated body with back plate suitable for batten / angle fittings complete all as specified and directed.

Material and Labour for distribution board, vertical, made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, VTPN 4 way , 3 phase , 415 volts grade with insulated rated bus bar assembly with isolated neutral bar,door earthing, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-08 Mechanical impact resistance, door earthing flush to wall, including testing suitable for fixing MCCB, MCB TPN/TP/SPN/SP etc, including dismantling of old UNSV one of any type/size from site and making good to disturbe surface wall complete all as directed (1.) MCCB 100 Amps , 25 KA, TP 415 Volts

Material and Labour for distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, SPN 12 way, 240 volts grade with 200 Amps insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-08 Mechanical impact resistance, flush to wall, including testing suitable for fixing MCB SPN, SP etc, including dismantling of old UNSV one of any size/type from site and making good to disturbe surface wall complete all as directed NOTE: Necessary blank plates if required any to cover the blank MCB's place in DB and the rate shall be deemed to included in the quoted rates.

Supply and fixing MCB of SP 5 to 32 Amps current carrying capacity, 240 V, 10KA 'C' curve fixed in the MCB DB complete with connection testing & commissioning complete all as directed

All as per ser item No. 35 above but for MCB SPN 40 to 63 Amps, 415 V grade

Supply and fixing Dusk & dawn roadway luminaries 45 Watt, 230 V AC, 5700K outdoor type with epoxy black powder coated sheet, high pressure die-cast aluminum hosing and heat resistant complete with impact and corrosion resistant including thermal management in multiple optics, PF>95%, THD<10%, Lumen>4500 lm with IP 65/66 protection complete incl connecting wire with flexible PVC insulated copper cables from ceiling rose to fitting including driver, lamp bracket made of 32mm bore galvanised iron light grade pipe made to shape having overall length not exceeding 1.5 mtr, through mild steel clamp of 25mm width and four Nos. nuts, bolts & washers of 12mm dia, 100mm long fixed to wall with all other fittings complete and testing all as specified and directed.

Supply and fixing storage electric heater (Geyser), flexible mounting of capacity 25 ltrs, single phase, 240 volts, AC, white colour, with incoloy heating element and PUF insulation, ISI marked BEE 5 star rated complete with high precision & externally adustable capillary thermostat for temp regulation, backup safety overheating capillary therrmal cut out at 95ºC, temperature display, etc., including provn of new suitable holding clamp, MS bolts, grouted to wall and connecting up including 3 core sheathed multi-stranded flexible copper conductor cable connected with 15/16 Amp plug top and provn of water connections with new PVC steel braided inlet/outlet connection pipe 15mm dia, 450mm long with two numbers brass union, NRV of suitable size, check/end nuts with washers, 15mm dia 100mm long nipples (02 Nos) for hot water and cold water connections including writing MES No. and making good to the disturbed surface in cement morter as required and testing complete all as directed NOTE: Cost of flexible copper cable of 3 core, PVC steel braided inlet/outlet pipe of 15mm dia, 450mm long with brass union, NRV, check/end nuts, nipples, MS bolts, etc., and minor parts, if any, other than those are not specified in the schedule and required for smooth functioning of geyser will be deemed to be included in the quoted rate

Supply and fixing in replacement, Sub main wiring with two single pole 6 sqmm (nominal area) stranded copper conductor FRLS PVC insulated and unsheathed cable drawn in and including non metalic PVC rigid conduit medium grade of suitable size with all standared fitting, on surface including one run of continuous PVC insulated standed copper conductor PVC insulated stranded copper conductor FRLS cable 6 sqmm (nominal area for earth continuty, including taking out and removal of old sub main wiring, complete all as specified and directed Note:- 1 Two runs of 6 sqmm main cable one run of 6 sqmm for earth cable & conduit shall be measured as one unit one running meter.

Supply and fixing in replacement, Sub main wiring with two single pole 4 sqmm (nominal area) stranded copper conductor FRLS PVC insulated and unsheathed cable drawn in and including non metalic PVC rigid conduit medium grade of suitable size with all standared fitting, on surface including one run of continuous PVC insulated standed copper conductor PVC insulated stranded copper conductor FRLS cable 4 sqmm (nominal area for earth continuty, including taking out and removal of old sub main wiring, complete all as specified and directed Note:- 1 Two runs of 4 sqmm main cable one run of 4 sqmm for earth cable & conduit shall be measured as one unit one running meter.

Supply and Fixing bus bar enclosure 800 mm x 600 mm x 200 mm made out of 3.15 mm thick CRCA steel duly powder coated and including 200 amp, 25 kA MCCB 4 pole, thermal magnetic based fitted in bus bar enclosure using 400 Amp rated bus bar, 25x10mm aluminium and RYB indication lamps duly protected by 2A SP MCB outdoor type welded to suitable size MS angle iron frame and embedded in PCC 1:2:4 type B-1 ; Complete all as specified and as directed by the Engineer-in-charge.Note - Height of the enclouser from ground level 0.5 meter complete all as specified and directed

Material & Labour in replacement Earthing complete with galvanized steel earth plate electrods of size 60cmx60cmx6mm thick burried directly in ground vertically(earth pit not less than 2.25 mr deep below normal ground level) with top edge of the plate not less than 1.5 mr below normal ground level connected to galvanized iron or steel earth wire 4 mm dia by means of bolts nuts check nuts and Gl washers of Galvanised iron protected by steel pipe 15mm (light grade) all as shown in elecrrical plate No.3 of SSR Part-l and connecting to earthing test point (earth test point to be provided at 5 mtr distance from earth pit) and testing on completion including necessary excavation and earth work. The rate also include charcoal dust and salt in alternate layers 25 mm dia light grade Gl pipe, funnel, wire mesh. Concrete 1:3:6 type C-1 for pit and RCC pit cover. The extra cost of the water- ing pipe,bends, elbows shall be included in the unit rate. Note: RCC pit cover shall be precast of RCC 1:2:4type B-1 80mm thick reinforced with XPM weighing not less than 4 Kg/Sqm complete all as specified and directed

M/s. M Company (BID ID -3383575)