Spl repair to bldg No P-25 to P-27 (Cook House) under AGE B/R-I, GE Gurdaspur.

Amount

Demolition mud phuska in roofs any thickness including plastering and leeping complete all as specified and directed.

Dismantling of roof brick tiles fixed in cement mortar in single layer roughening the surface of old concrete floor picking sweeping clean and washing down with water to remove dust/mud etc and brushing neat cement slurry @ 3kg/Sqm all as specified and directed by Engineer-in-Charge.

M&L for cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate finishing the surface even and smooth without using extra cement using complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non woven fabric (weight not less than 150 gms/ Sqm) including bitumen primer @ 0.40 kg /Sqm by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed over a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surfaces all as per manufacturer's instructions.

M&L for 40mm thick brick tiles laid over 15mm thick ready mix mortar bedding layer in grouting and pointing with CM (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed by Engineer-in-Charge.

All a per Srl item No 05 above but except tiles (old serviceable dismantled tiles obtained from Srl item No 01 shall be reused after necessary cleaning of mortar)

M&L for PCC 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in roof kerbs, kerb, coping etc. complete all as specified and directed.

M&L for removing existing pointing and flush pointing to bricks laid flat or brick tiles in pavings and pointing in CM (1:3) complete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound.

Demolition of cement concrete in ground floor & paving n.exc 15cm above ground level all as directed.

M&L for cement concrete type 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection thickness of 75mm finishing the surface even and fair with joints to full depth at corners, along the wall and @ 3 meters c/c filled with mastic mortar complete all as specified

M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match existing surface including 15 mm thick in ready mix mortar including dismantling existing tiles complete all as specified.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick in ready mix mortar and including demolition of existing tiles and screed complete all as spcified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles in vertical surface of size 450X300x7mm thick joint free on and incl 10mm thick screed bed in cm(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles including demolition of existing tiles and screed complete all as speciifed and directed by Engineer-in-Charge.

Demolition Stone slabs and tiles of any description or thickness in floors, aprons, counter platforms etc.

S&F machine cut kota stone slab flooring 20-25mm thick over cement screed 15mm thick in ready mix mortar jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) in floor, stair, skirting etc. complete all as specified and directed by Engineer-in-Charge.

Labour only for grinding of existing kota stone slab flooring including rubbing and polishing complete all as specified and directed.

M & L for green marble work 14-16 mm thick (table rubbed and polished) in steps, jambs, Shelves, pillars window cills, cooking platforms, stair case and like and pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade incl 20mm thick ready mix mortar complete all as specified and directed.

Demolition of RCC as fascia, projection, chajja, parapet, shelves etc of any description complete all as specified and directed by Engr-in-charge.

Form work to rough finished surface of concrete flat to soffits of shelve, chajja, fins etc including supports over hangs upto 12m height all as specified & directed.

M&L for TMT bars 6 to 8mm dia cut to length bent to shape as required including crancking spirally for hooking ends and binding with and including MS wire annealed n.less than 0.9mm dia complete all as specified.

M&L for RCC in 1:2:4 type B-0(using 12.5 mm graded stone agg) as in chajjas facia, shelves, lintel etc and similar work all as spd.

S&F steel window box type made of ERW tube hollow P section of size 60mmX25mm double rebated outer frame comprising double shutters i.e. guaged skelton & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI, 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 incl one shop coat of priming and two coat of synthetic enamel paint including taking down old existing window complete: :- (i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii) MS Tower bolt 150mm long-02 Nos per leaf (iv) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (v) Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). Note: Wire cloth, glass shall be measured and paid for separately

S&F box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises of glazed shutter, frame of ERW tube and flat iron, 2mm thick welded/ screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD1019/08 sheet 1/3 to 3/3 dt 01 May 2008 incuding cutting and making good dismantled portion in PCC 1:2:4 type B-1incl one shop coat of priming and two coat of synthetic enamel paint including taking down old existing window complete all as specified and directed. Note : Sheet glass and wiremesh shall be measured and paid separately

S&F 3mm thick silicon hard coarted transparent polycarbonate sheet glass ordinary quality and glazing with silicon and filling gap with oil putting in squares n exc1.00 Sqm each fix on steel, wooden etc frame complete all as specified and directed.

S&F in repair 3mm thick silicon hard coated transparent polycarbonate sheet glass ordinary quality and glazing with silicon and filling gap with oil putting in squares n exc1.00 Sqm each fix on steel, wooden etc frame complete all as specified and directed.

S&F cutrain rod 20mm dia of mild steel, chromium coated with brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed.

M&L for 12 mm thick rendering of ready mix mortar of approved make on brick work/stone/concrete wall etc. internal surfaces finished even and smooth without using extra cement of any shape, any size incl taking down existing plaster of any size incl raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for 5 mm thick rendering of ready mix mortar of approved make on brick work/stone/concrete wall etc. internal surfaces finished even and smooth without using extra cement of any shape, any size incl taking down existing plaster of any thickness incl raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for 15 mm thick rendering of ready mix mortar of approved make on brick work/stone/concrete wall, facia, projection etc. external surfaces finished even and smooth without using extra cement of any shape, any size incl taking down existing plaster of any thickness raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for preparation of newly plastered surface and applying three coat of colour wash on wall complete all as specified and directed.

M&L for preparation of newly plastered surface and applying two coats of Oil bound distemper on wall over a coat of primer on wall complete all as specified and directed.

M&L for preparation of newly plastered surface and applying three coat of colour wash on ceiling complete all as specified and directed.

M&L for preparation of newly plastered surface and applying two coats of cement base paint on wall complete all as specified and directed.

Preparation of old surface including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots on existing distempered surfaces and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty on wall complete all as specified and directed.

M&L for preparation of old surface including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. on existing surfaces making good holes, cracks, etc and applying two coats of colour wash on wall complete all as specified and directed.

M&L for preparation of old surface including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots. on existing distempered surfaces making good holes, cracks, etc and applying two coats of colour wash on ceiling complete all as specified and directed.

M&L for complete removal of existing treatment, preparation of old surface and applying two coats of cement base paint on wall making good holes, cracks, etc complete all as specified and directed.

M&L for preparation of old painted steel surface exc 10cm width or girth and applying one coat of synthetic enamel paint ht upto 12m complete all as specified and directed.

M&L for preparation of old painted wooden surface exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking down chowkats with shutter n.exc 1.50 Sqm each without taking off shutter all as directed by Engineer-in-Charge

All as per Srl item No 41 here-in-before but exc 1.50 sqm but n.exc 4 sqm.

Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed.

S&F factory made single extruded WPC ( wood polymer composite) solid door frames/ chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as directed by Engineer-in-Charge. .

S&F 30 mm thick factory made single extruded WPC solid plain flush door shutter comprising of virgin polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws all as directed by Engineer-In-Charge.

S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hinges, lock strike, plate etc complete of size 105x60mm all as spd including one shop coat of priming and two coats of synthetic enamel paint and filling PCC 1:2:4, type-B0 (using 12.5mm graded crushed stone aggregate) in the frames complete all as specified and directed by Engineer-in-Charge.

S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hinges, lock strike, plate etc complete of size 125x60mm all as spd including one shop coat of priming and two coats of synthetic enamel paint and filling PCC 1:2:4, type-B0 (using 12.5mm graded crushed stone aggregate) in the frames complete all as specified and directed.

S&F 35 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides incl smooth finishing of sides lcomplete all as specified and directed.

S&F 35mm thick factory made glazed and skeleton shutters 2nd class hard wood, open rebated and prepared to receive glass, gauze, etc. but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc , sizes of members of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a) complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F aluminium anodized barel tower bolt of extruded section 150mm long complete all as specified and directed.

S&F aluminium alloy handle fabricated type anodized of size 150 mm long complete all as specified and directed.

S&F 100mm size extruded aluminium alloy butt hinge with galvanised mild steel hinge pin type B-21 fixed with metal surface through screw complete all as specified and directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs, including roller and roller plate joint through welding/ bolt in metal/wooden frame be carried out or necessary alternative arrangements to be done complete all as specified and directed.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of primer all as directed.

S&F 18 mm thick plywood, grade BWR, laminated on both side with wooden decorative choice lamination in glossy finishes , Incl fire resistant, moisture resistant type fixed with screws to timber/steel frame work Incl 6mm thick teak wood lipping fixed with nails on all sides on cupboard, kitchen cabinets and like complete all as specified and directed by Engineer-in-Charge.

S&F in repair 25 mm thick block boards, grade 1 quality, interior grade, laminated on both side with wooden decorative choice lamination in glossy finishes fixed with screws to steel frame work for shelves etc. Incl 6mm thick teak wood lipping fixed with nails on all sides on cupboard, kitchen cabinets and like complete all as specified and directed by Engineer-in-Charge.

S&F mild steel work Fe 290 (Gde -E-165) in framed work as in door frame, shutter or gates of angle iron or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or orther covering doors etc to be prepared for hanging or sliding with and including steel hanging door fittings and hanging also fastening complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in back filling of of chowkhats/frame complete all as specified and directed.

M&L for cutting holes in brick walls but depth of embedded portion of holddfasts or lugs measured from the face of the jamb into the wall exc half bricks but n exc full bricks built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed by Engineer-in-Charge.

S&F 100mm size medium weight mild steel butt hinge fixed with metal surface through bolt or weld with screw complete all as specified and directed.

S&F aluminium alloyed handle fabricated type anodized of size 100 mm long complete all as specified and directed.

S&F 75mm size hasp and staple safety type aluminium anodised hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings including taking up and down complete all as specified and directed.

Re-fixing old steel tubing including fittings 15mm bore in new or old position including cleaning the same incl taking down complete all as specified and directed

S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings including taking up and down complete all as specified and directed.

S&F rotational moulded polytheylene white triple layered white water storage tanks of capacity 1000 litres (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank and 20mm dia brass float valve with polythene float and flynut complete all as specified.

S&F in repair gun-metal, globe or gate valves,20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair bib taps (long nose) cast copper alloy 15mm bore fancy type chromium plated alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair stop valves or angle valve cast copper alloy 15mm bore fancy type chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair pillar taps (long nose), cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed.

S&F stainless steel tubular 20 mm dia towel rail 60 cm long fixed to wall complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC low level duel type flushing cistern 10ltr capacity, with syphonic, action PVC float valve, and 32mm bore PVC flush pipe etc complete all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with PVC `P’ or `S’ trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 complete all as specified and directed. Note:- Flush pipe and flushing cistern to be measured and paid separately.

S&F in repair vitreous China wash basin, with pedestal white flat back, size 550x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, 32mm dia CP brass waste coupling with 32 mm dia waste pipe complete all as specified and directed.

Dismantling of cast iron, PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches all as directed by Engineer-in-Charge.

S&F PVC (SWR)pipes 110mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height complete all as specified and directed.

S&F in repair PVC (SWR ) bends, 110 mm bore any radius complete all as specified and directed.

S & F Stack clamps (110 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

M&L in repair PVC(SWR) floor trap incl jointing with solvent cement 100mm dia complete all as specified and directed.

M&L for chipping off existing loose, damaged concrete from RCC members of all affected RCC columns, beams, slabs and chajjas on external and internal facades, etc for providing PMM (Polymer modified cementitious mortar):- (i) Dry sub strate surface and free of debris & dust. (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of n exc 50 mm thickness. Note : Application of PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as rcommended by manufacturer complete all as specified and directed. Note: - Cost of formwork, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars et

M&L for brick work with fly ash brick, straight or curved on plan exc 6m mean radius built in ready mix mortar brick in fixed complete all as spcified and directed by Engineer-in-Charge.

S&F in repair stainless steel cockroach trap with hole, round 100mm dia complete all as specified and directed

S&F pre-painted coloured galvantume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick having tensile strength of 550 Mpa as in roof covering/cladding to walls,fixed with self tapping screws including taking down AC sheets all as specified and directed.

Dismantling framed work of timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed.

S&F of Rolled mild steel Gde Fe-410-W Gde E-250 Quality-A in roof trusses (framed), trussed, purlins crane gantries, joist, channel, steel tube, rails & fastenings & heavy brackets framimg (beam, tee, angle, coulmn, gusset plates, channel, hollow square/rectangular or flat section) including distance pieces, cleats with riveted, bolted or welded attachment etc. complete all as specified and directed by Engr-In-Charge.

M&L for preparation of new steel surface exc 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, crumple joint etc. fixed with self tapping screws as specified etc. as required including taking down existing steel sheets etc complete all as specified and directed by EIC.

Bailing out sludge from manholes of any size manually or with the help of pump as per site condition and disposal of sludge, solids foul material obtained to any distance exc 500 mtr in low lying area, including removing and refixing manhole covers and flushing with adequate water the depth of manhole not exc 1.0 m all as directed by Engineer-in Charge.

M&L for precast RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in cover slab for manhole and similar work etc complete all as specified and directed.

M&L for TMT bars 6 to 8mm dia and over cut to length bent to shape required including crancking spirally for hooking ends and binding with and including MS wire annealed n.less than 0.9mm dia complete all as specified.

M&L cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L for chequered cement concrete tiles with grey cement and pigment 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry incl 15mm thick ready mix mortar screed bed complete all as specified and as directed by Engr-in-Charge.

S&F in repair stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc. with bowl size 560mm x 405mm x 250mm with coupling and necessary fixing arrangment complete all as specified as directed.

E/M PORTION Taking down carefully aluminium/copper point wiring for light, fan, bell, socket of point complete fittings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making goods disturbed surfaces of walls, floors etc.

M&L for point wiring with PVC insulated and PVC unsheathed multistranded FRLSH copper conductor cable of size 1.5 Sqmm including concealed PVC conduit fittings and making good to the disturbed surfaces with continuous earth wire of copper 1.5 Sqmm dia to common earth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing to CI/MS boxes for mounting of accessories like surfaces sockets and regulators etc. complete all as specified for One light / Fan/ bell point controlled by one way switch complete all as specified and directed.

All as per Srl item No 101here-in-before but one 5 pin socket outlet 5 amps on same board.

All as per Srl item No 101 here-in-before but 5 amps socket outlet on independent board.

All as per Srl item No.101 here-in-before but wiring with 2.5 Sqmm FRLSH copper wire including one earth wire 2.5 sqmm of copper for 15 Amps 3 pin socket outlet .

M&L for sub main wiring with two single core multi stranded PVC insulated, unsheathed copper conductor of grade 1100 Volt, FRLSH cable of size 6 sqmm (Red for phase and black for neutral) and including electrical grade PVC conduits of desired colour not less than 1.2mm thick and 32mm wide and 6 sqmm multistranded copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly complete and taking down old unsedrviceable wiring complete all as specified and directed. Note :- (a) Cost of making good the disturbed surface plastering/ filling putty alongwith matching with the existing colour with MES approval make of distemper is deemed to be included in the quoted rate by contractor. (b) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano flush type single pole one way 5 amps.

S&F socket outlet 3 pin 5 amps flush type.

S&F switch flush type 15 amps single pole one way.

S&F socket outlet 3 pin 15 amps flush type.

S&F in replacement surface mounting universal batten housing made of powder coated CRCA sheet suitabe for and upto 1 x 18/ 20W LED tube rod and taking down old unserviceable fitting complete all as specified and directed by Engineer-in-Charge.

S&F LED tube light 20W ultra bright LED polycarbonate tube light with high efficiency suitable for fitting into tube light batten fitting complete all as as specified and directed by Engineer-in-Charge.

Taking down carefully ceiling fan complete fittings at site, removing fans are deposting to MES store yard and refixing after completeion of work at the site.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose to connector to fan complete including replacement of one pair of canopy complete all as as specified and directed by Engineer-in-Charge.

S&F in replacement of fan regulator electronic type 5 step 100 watt, 240 volt and connecting complete all as as specified and directed by Engineer-in-Charge.

S&F for lamp holder PVC body angle type including 9 watt LED bulb polycarbonate body complete all as as specified and directed by Engineer-in-Charge.

M&L for ceiling rose, surface bakelite 65 x50mm three terminal.

S&F in replacement GI pipe bracket made out of GI pipe light grade 32 mm dia and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 32mm thick with nut & bolts, washers complete including dismentling the existing GI pipe bracket and drilling of holes for nuts & bolts etc complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply and fixing in repair sheet metal enclosure for DB’s when MCB’s to be used of 240 volt 8 way with 200 amps rated bus bar SPN double door complete all as specified and directed. (Note :- All the connection of incoming and out going wire in MCB will be made with thimble with suitable size).

S&F in repair MCB single pole 6 amps to 32 amps complete all as specified and directed.

All as per Srl item No 120 here-in-before but single pole and neutral 40-63 amps series.

Material and labour for distribution board made out of CRCA sheet DB vertical type double door TPN 4 Way MS sheet including fixing in the wall, cutting chases, grounting and necessary patch work and white wash to match with the existing including making connections all as directed containing the folowings:- Note :- All the connection of incoming and out going wire in MCCB and MCB will be made with thimble with suitable size as directed. (a) MCCB 4 Pole 63 Amps 16 KA breaking capacity with thermal release: 01 No (In coming). (b) Bus bar 200 amp rated made out of Aluminium on insulated duly insulated wire adhesive tape RYB & black-4 Nos. (c) MCB SPN 40 Amp- 4 Nos, MCB SP 40 Amp- 04 Nos (Out going). (d) Connection from MCCB to bus bar will be made with aluminium strip of suitable sizeas directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm ×60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54cm x 54cm x 5cm including 8mm dia TMT bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia MS bar, funnel & wire mesh, excavation and earth work in soft loose of soil including dismantling existing complete all as specified & directed by Engr-in-charge.

A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender to the tune of Rs. 48560. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

VOHRA CONSTRUCTION CO (BID ID -3285467)

talwinder singh and co (BID ID -3285380)

buta singh and sons (BID ID -3281600)