PIPE LINE & STRUCTURE PAINTING JOB AT HALDIA TML

SURFACE PREPARATION FOR 1650-HALDIA TERMINAL — SURFACE PREPARATION: HAND TOOL CLEANING USING WIRE BRUSH ETC. CONFORMING TO SSPC-SP-2 OR ST2 STANDARD SCOPE OF WORK:1. VENDOR HAS TO CARRY OUT THE SURFACE PREPARATION AS PER THE STANDARD GIVEN IN INSULATION SPECIFICATIONS. . THE SURFACE HAS TO BE CAREFULLY PREPARED BEFORE APPLICATION OF THE PAINT/INSULATION. TOTALLY REMOVE ANY LOOSE OR DAMAGED COATING (I.E. COAL TAR ENAMEL, BITUMEN OR ANY OTHER PAINT,ETC.),RUST,MOISTURE,GREASE AND ANY OTHER FOREIGN MATTER. TO REMOVE OIL,GREASE,ETC. AN ORGANIC SOLVENT MAY BE USED LIKE PETROLEUM SPIRIT OR ETHANOL. AS PER ATTACHED SPECIFICATION WHEREVER REQUIRED SURFACE SHOULD BE CLEANED TO STANDARD ST-2 HAND TOOL CLEANING ALL TOOLS AND TACKLES,MACHINES,MANPOWER,AND ANY CONSUMABLES/NON CONSUMABLES FOR SURFACE PREPARATION ARE IN

SPLY & APLY OF ONE COAT — SUPPLY AND PAINTING OF ONE COAT-MASTIC PRIMER-1 X 100 MICRON HAS TO BE APPLIED (SINGLE COAT).SUPPLY AND APPLICATION OF ONE COAT OF 100 MICRON SELF PRIMING SURFACE TOLERANT EPOXY HIGH BUILD MASTIC COATING WITH POLYAMIDE AMINE CATALYST PRIMER OF APPROVED MAKE TO THE PIPELINES OF VARYING SIZES FROM 2'' TO 24''. RATE TO INCLUDE WASTAGES, MIXING THE PAINT PROPERLY AS PER MANUFACTURER'S SPECIFICATIONS, APPLYING WITH BRUSH/ CONVENTIONAL /AIRLESS SPRAY GUN TILL 100 MICRON DFT OF PAINT THICKNESS IS OBTAINED, TESTING FOR THICKNESS.

SPLY & APLY OF 2 COATINGS — SUPPLY AND PAINTING OF 2 COATINGS OF ACRYLIC POLYURETHANE FINISH PAINT WITH EACH COAT OF 30-40 MICRONS DFT

BAND PAINTING ON THE — "BAND PAINTING ON THE PIPELINES AS PER INDUSTRY QUALITY CONTROL MANUAL (IQCM). PIPELINES SHALL BE COLOUR CODED TO INDICATE THE PRODUCT THAT IS BEING CARRIED. COLOUR CODING FOR ALL PRODUCTS SHALL HAVE BAND(S) OF 100 MM ON EACH SIDE WITH A GAP OF 300 MM IN BETWEEN. THE PRODUCT CARRIED SHALL BE WRITTEN IN A GAP OF 300 MM IN BLACK LETTERS FOR WHITE OILS IN THE DIRECTION OF FLOW. THE SIZE OF LETTERS SHALL BE HALF THE DIAMETER OF THE PIPELINES. THE WIDTH OF THE ARROW SHALL BE ONE THIRD OF THE DIAMETER OF PIPELINE AND 300 MM LONG ARROW SHALL BE PAINTED AFTER EACH BAND ON THE PIPELINE WITHRESPECTIVE COLOUR CODE IN THE DIRECTION OF FLOW."

SURFACE PREPARATION FOR 1650-HALDIA TERMINAL — SURFACE PREPARATION: VENDOR HAS TO CARRY OUT THE SURFACE PREPARATION AS PER THE STANDARD GIVEN IN INSULATION SPECIFICATIONS. . THE SURFACE HAS TO BE CAREFULLY ARE IN VENDOR’S SCOPE PREPARED BEFORE APPLICATION OF THE PAINT/INSULATION. TOTALLY REMOVE ANY LOOSE OR DAMAGED COATING (I.E. COAL TAR ENAMEL, BITUMEN OR ANY OTHER PAINT,ETC.),RUST,MOISTURE,GREASE AND ANY OTHER FOREIGN MATTER. TO REMOVE OIL,GREASE,ETC. AN ORGANIC SOLVENT MAY BE USED LIKE PETROLEUM SPIRIT OR ETHANOL. AS PER ATTACHED SPECIFICATION WHEREVER REQUIRED SURFACE SHOULD BE CLEANED TO STANDARD ST-2 HAND TOOL CLEANING ALL TOOLS AND TACKLES,MACHINES,MANPOWER,AND ANY CONSUMABLES/NON CONSUMABLES FOR SURFACE PREPARATION

PROVIDING & APPLYING ONE — Provide and apply one coat of inorganic zinc Phosphate primer of approved make on the cleaning surface of Structure and accessories and as specified (Min. DFT per coat by brush is 50 micron). Inclusive of all other incidental charges and testing charges as per IS Codal provisions in this connection all complete.

SPLY & APLY ONE COAT HB — Provide and apply one coat of polyamide cured high build epoxy coating based on laminar micaceaous iron oxide pigments (Epiguard high built M.I.O. brown or equivalent of approved per IS Codal provisions in this connection all complete. make) over the steel surface and as directed. (Minm. DFT per coat by brush 100 micron). Inclusive of all other incidental charges and testing charges as

SPLY & APLY 2 COATS — Provide and apply 2 (two) coats of Alyphatic Isocynate cured polyurethene paint of approved make over the surface at the locations over the steel surfaces as directed by Engineer (Minm. DFT per coat by brush 40 micron). Inclusive of all other incidental charges and testing charges as per IS Codal provisions in this connection all complete.