Hubballi Division-Miscellaneous annual maintenance activites for Hubli Railway station (including HUbli Yard, 2nd entry, 3rd entry buildings and other service buildings in station area) (Special work-11)

Item Breakup - B-SCH-B

"Maintenance , repair / replacement in Per each 624.00 respect of 1) Masonry works - brick work, Team/day concreting,grouting, plastering, pointing, flooring / dado work, Open drainage works, roof leakages etc. 2) Carpentry works - Wood work, doors & windows,cup boards, frames, shutters fittings & fastenings,rafters, reapers, wooden furnitures, roof sheeting etc.3) Plumbing works- Day to day maintenance and repair works in Plumbing related. By supplying multi skilled team. Each team of Multi skilled man comprises of 2 members of mason or carpenter or plumber or combination as per requirement with all Contractors tools, transportation, lead & lift,equipment's & scaffolding arrangements, safety equipment, maintenance of tools & other equipments etc. Material required for repair / replacement / other petty repair works will be supplied by the Railway at free of cost at work spot and as decided by Engineer in charge. The rate is for any one team of multi skilled members. Note: 1) Each member of team should report to SSE/Works - In charge on or before 9hrs on required working days as required by Railways 2) The Contractor should attend the maintenance, repair / replacement works with number of labour specified - one team of 2 nos for each category of work as directed by the Engineer in charge 3) A day to day register shall be maintained for this purpose and the same should be produced to the SSE/Works - In charge when ever required and produced the same for making payment 4) If any complaint / deficiency noticed in the working of the labourer, they should replaced with new person as per the direction of the Engineer in charge,. 5 ) Two times maintenance cost (per team / per day) will be imposed as penalty for the deficiency in working by the contractor's labour 6) The contractor should comply with existing laws and acts of Govt. of India and State Govt. Law and acts in engagement and working with labour 7) Mobile phone communication facility should be provided by the contractor to the each team for communication with departmental officials for instructions." Total 1378971.36

Item Breakup - D-SCH-D

of 88 mm, weighing not less than 190 gms. HUBLI DIVISION-ENGG/SOUTH WESTERN RLY 17.81 Providing and fixing floor mounted, white Each 5 18212.9 91064.5 vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china 108 cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 18.0 WATER SUPPLY 18.7S C.P.V.C. PIPES Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 18.7 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. ( Internal work - Exposed on wall ) 109 18.7.1 15 mm nominal dia Pipes Metre 200 286.8 57360 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & 18.8 fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 110 18.8.1 15 mm nominal dia Pipes Metre 300 497.8 149340 111 18.8.2 20 mm nominal dia Pipes Metre 400 537.6 215040 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This 18.9 includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 112 18.9.2 20 mm nominal dia Pipes Metre 200 274.3 54860 113 18.9.3 25 mm nominal dia Pipes Metre 250 355.4 88850 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and 18.10 making good the walls etc. ( Internal work - Exposed on wall ) 114 18.10.6 50 mm dia nominal bore Metre 20 1048.35 20967 Providing and fixing G.I. pipes complete with 18.12 G.I. fittings including trenching and refilling etc. External work 115 18.12.6 50 mm dia nominal bore Metre 50 762.15 38107.5 18.15S BRASS FITTINGS Providing and fixing brass bib cock of 18.15 approved quality : 116 18.15.1 15 mm nominal bore Each 100 353.25 35325 Providing and fixing brass stop cock of 18.16 approved quality : 117 18.16.1 15 mm nominal bore Each 100 353.25 35325 HUBLI DIVISION-ENGG/SOUTH WESTERN RLY Providing and fixing gun metal gate valve 18.17 with C.I. wheel of approved quality (screwed end) : 118 18.17.1 25 mm nominal bore Each 50 622.4 31120 119 18.17.4 50 mm nominal bore Each 5 1026.65 5133.25 Providing and fixing brass ferrule with C.I. 18.20 mouth cover including boring and tapping the main : 120 18.20.1 15 mm nominal bore Each 100 329.3 32930 Providing and fixing uplasticised PVC 18.21 connection pipe with brass unions : 18.21.1 30 cm length 121 18.21.1.1 15 mm nominal bore Each 100 85 8500 Providing and fixing C.P. brass shower rose 18.22 with 15 or 20 mm inlet 122 18.22.1 100 mm diameter Each 150 193.95 29092.5 123 18.22.2 150 mm diameter Each 50 222.35 11117.5 18.49S C.P. BRASS FITTINGS Providing and fixing C.P. brass bib cock of 18.49 approved quality conforming to IS:8931 : 124 18.49.1 15 mm nominal bore Each 100 506.8 50680 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS 18.50 standards and weighing not less than 810 gms. 125 18.50.1 15 mm nominal bore Each 100 820.7 82070 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS 18.51 standards and weighing not less than 690 gms. 126 18.51.1 15 mm nominal bore Each 100 798.95 79895 Providing and fixing C.P. brass stop cock 18.52 (concealed) of standard design and of approved make conforming to IS:8931. 127 18.52.1 15 mm nominal bore Each 100 670.45 67045 Providing and fixing C.P. brass angle valve for 18.53 basin mixer and geyser points of approved quality conforming to IS:8931 128 18.53.1 15mm nominal bore Each 100 574.3 57430 18.54S PTMT FITTINGS Providing and fixing PTMT, push cock of 18.57 approved quality and colour. 18.57.1 15 mm nominal bore, 98 mm long, weighing Each 100 112.8 11280 129 not less than 75 gms 19.0 DRAINAGE 19.1S STONE WARE PIPES AND FITTINGS Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed 19.6 with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 130 19.6.4 300 mm dia. R.C.C. pipe Metre 20 994.3 19886 131 19.6.7 600 mm dia. R.C.C. pipe Metre 20 2243.4 44868 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb 19.32 shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) Each 3 26861.9 80585.7 132 bricks of class designation 7.5 21.0 ALUMINIUM WORK 21.1S General HUBLI DIVISION-ENGG/SOUTH WESTERN RLY Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ 21.1 neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : 21.1.1 For fixed portion 21.1.1.1 Anodised aluminium (anodised transparent or Kg 500 495.05 247525 133 dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings 21.1.2 wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 21.1.2.1 Anodised aluminium (anodised transparent or Kg 350 598.6 209510 134 dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene 21.3 gasket etc. complete as per the architectural drawings and the directions of engineer-in- charge . (Cost of aluminium snap beading shall be paid in basic item): 21.3.1 With float glass panes of 4.0 mm thickness Sqm 100 1176.8 117680 135 (weight not less than 10kg/sqm) 22.0 WATER PROOFING 22.1S General 22.5 Providing and laying water proofing Sqm 60 617.05 37023 treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 136 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. HUBLI DIVISION-ENGG/SOUTH WESTERN RLY 22.22A P r o v i d i n g and applying fibre reinforced Sqm 200 563.1 112620 elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric water proofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted 137 elastomeric water proofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in- Charge. STRUCTURAL GLAZING ALUMINIUM 25.0 COMPOSITE PANEL 25.1S General 25.6 Providing and supplying Spandrel Glass Sqm 50 2450.15 122507.5 Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of 138 grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of relevant Item*). "(i) Coloured tinted float glass 6 mm thick substrate with reflective soft coating on face # 2, having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement. HUBLI DIVISION-ENGG/SOUTH WESTERN RLY 25.8 Design supply & installation of suspended Sqm 30 9502.35 285070.5 Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2 mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The 139 complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T& P,scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors,SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured. Total 31101764.15