ADDN/ALTN AND SPECIAL REPAIRS TO BLDG NO. P-67 (SAILORS AND MD ACCOMMODATION) AT HQ 31 WEU

Amount

SCHEDULE 'A' PART I (B/R WORKS) Taking down cement plaster on brick or concrete surfaces etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed.

M&L for 15 mm thick ready mixed cement based plaster in CM 1:4 with 40 % fly ash on fair faces of brickwork or concrete surfaces finished the surfaces even & smooth including Make Easy plast from wall plast chemplast, Ready Plast from ultra tech or Asian smart care ready mixcomplete all as specified and directed.

M&L for 10 mm thick Polymer modified ready mixed cement based plaster in CM 1:6 with 40 % fly ash on fair faces of brickwork or concrete surfaces finished the surfaces even & smooth Make Easy plast from wall plast chemplast, Ready Plast from ultra tech Or asian smart care ready mix complete all as specified.

M&L for 5mm thick ready mix plaster ceiling surface finished even &smooth with complete all as specified and directed

Supply only integral water proofing compound

Chipping, removing carefully loose/damaged concrete including plastering (total thickness upto 60mm ) from surfaces of RCC members, in any location by low impact Hammer/Breaker without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land complete all as specified and directed. Note : Hard concrete shall not be removed by force

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit or Asian smart care polymer modified ready mixupto 20mm thickness including levelling, profiling etc complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from M/s. Krishna Conchem (Molith-PMM) OR Polymer mortar HB of Dr Fixit Or asian smart care polymer modified ready mix while the bonding agent is still tacking, exceeding 20mm thickness and not exceeding 40mm thickness in two layers, each layer not exceeding 20mm, including levelling, profiling etc, complete all as specified and directed.

M&L for cleaning existing reinforcement with wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hour between the coats, complete all as specified and directed. [Note :- Mode of measurement: superficial area covered between the end to end reinforcement bars (i.e., concrete area excluding all side covers will be measured.

M&L for Anticorrosive Treatment to Reinforcement using IPNET-RB of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces complete all as specified and directed. Note :- Mode of measurement: superficial area covered between the end to end reinforcement bars (i.e., concrete area excluding all side covers) will be measured.

M & L preparing new surfaces of walls applying two coats of oil bound distemper over 3mm thick wall care putty over a coat of alakali resistant primer complete all as specified & directed by EIC.

M & L for preparing old decorated surfaces of wall (plasterered or unplastered or complete removal of existing treatment) & applying two coats of oil bound distemper over 3mm thick wall care putty over a coat of primer complete all as specified.

M & L for preparing old decorated surfaces of ceiling (plasterered or unplastered or complete removal of existing treatment) & applying two coats of oil bound distemper over 3mm thick wall care putty over a coat of primer complete all as specified.

M& L for preparation of old decorated surfaces of wall and applying two coat of white wash on walls complete all as specified and directed

M& L for preparation of old decorated surfaces of wall and applying two coats of white wash on ceiling complete all as specified and directed

M&L for preparation of new plastered surfaces of wall applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed.

S & F in repairs 19 mm thick alumnium powder coated curtain rails with fixing brackets stops rollers etc complete all as specified and directed

S & F in repairs Vitreous China wash basin, white, flat back, size 580x450 mm including brackets, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F floor door stopper aluminium body over length of cover plate 140 mm and tonque anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

Taking down carefully aluminium sliding window shutters including existing rubber gasket complete and re-fixing the shutters in same existing position after replacement of broken glass/stainless steel wire mesh with rubber gasket and area of window exc 1.20 sqm but not exc 3.78 Sqm in each including necessary scaffolding etc complete all as specified and directed.

Taking down carefully aluminium sliding window shutters from the frames or chowkhat and supply and fix New locking arrangement in place of old one and re-fixing the same shuters in existing position after repair work or replacement of new locking arrangement and necessary scafolding etc complete all as specified and directed

S&F standard aluminum section powder coated(min thickness 50 micron) in partition / frame and door shutter, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or Bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc completed all as specified and directed (Aluminum section shall be of make Jindal / Hindalco / Indalco). Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

S & F in repairs aluminium anodised grill DG-104/DG-102 10 mm dia of extruded aluminium section of suitable size and frame including fixing with U clip or F section beading complete with all fitting and fixture and drilling required in RCC section in rectangular or arch type balcony opening of the building complete all as specified.

Supply only 4.00 mm thick sheet glass, ordinary quality, in squares not exc 0.5 Sqm each pane, complete all as specified and directed.

S&F inrepair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) not exceeding 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) exceeding 1.5 Sqm but not exc 4 Sqm each complete all as specified and directed.

S& F second class hard wood , plain ,soild ,straight chowkats and frames, wrought , rebated on soild rounded or chamfered , put together with gule pinned at joints etc complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with Square tube, supply and fixing in opening as per specification given under SSR Part II 2020 including making good the disturbed surface all as specified and directed. Make: SYNTEX/SHALIMAR/RAJSHRI

M&L for factory made solid PVC panel type PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2020 complete all as specified and directed. Make : SYNTEX/SHALIMAR/RAJSHRI

S&F 35 mm thick plain , framed ,panelled shutters ( any number of panels),in 2nd class hardwood,with panels of timber flat on both sides (feather edged) ,or of veenered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats complete all as specified and directed.

S & F 35 mm thick glazed and skeleton shutters, in 2nd class hardwood, open rebated and prepared to receive glass, gauze etc, (without sash bar )edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24(a) Complete al as specified and directed

M& L for preparation of newly or previously untreated surfaces of wood or wood based surfaces of any description not other wise described , over10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer etc complete all as specified and directed.

M& L for preparation of old surfaces wood or wood based surfaces of any description not other wise described , over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer etc complete all as specified and directed.

S&F extruded aluminum alloy handles (150mm ) fabricated type anodised complete all as specified and directed.

S&F hinges (125 mm) stainless steel medium weightcomplete all as specified and directed.

S&F aluminum anodised barrel tower bolts (150 mm ) of extruded sectioncomplete all as specified and directed.

S&F 300 mm Aluminium alloy , anodised , sliding door bolt with hasp, staple (bolt type ) and fixing clips of sheet , cast , exctruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar, bedding, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 10 mm thick vitrified tiles (square/rectangualr) light shade polished area of each tiles not exceeding 0.36 Sqm, in floors over screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed.

Description all as per Serial item No 40.00 above here-in-above but screed bed or bedding layer of mortar 10 mm thick in cement mortar 1:4 on walls surfaces, such as skirting, to slab etc. complete all as specified and as dircted.

M&L for coloured Non-skid ceramic tiles 7 to 8mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directed.

S& F coloured glazed ceramic tiles 350 x 250 x 7mm/450x350x7mm thick in dado/ skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match, over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M & L for machine cut cudappah stone slab as in window cills and jambs 20 mm thick to full thickness of wall fixed in steps over cement screed bed 20mm thick in CM 1:4 and jointed with grey cement paste and slurry including rubbing and polishing complete all as specified and directed.

M & L for Granite (of any type) tiles 20 mm thick over screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6, set machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over 10mm thick backing coat in CM 1:4 including rubbing and polishing complete all as specified and as directed. Note: For stairs and steps treads full length kota slab with double line groove cuts at edges shall be provided.

M& L for machine cut kota stone slab flooring 20-25 mm thick over screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfacey mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. Note : For stairs and steps risers full length kota slab shall be provided

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations over rendering 10 mm thick in CM 1:6 on brickwork or concrete surfaces complete all as specified and directed.

S&F in repairs 15mm bore bib taps cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F in repairs 15mm bore stop valve cast copper alloy screwed high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union complete all as specified and directed.

S&F in repairs 15mm bore pillar taps,chromium plated, cast copper alloy screwed high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union complete all as specified and directed.

S & F in repairs 10 litres PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repairs Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) complete all as specified and directed

M&L in repairs Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and as directed.

S & F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F cast iron Nahani trap 100mm dia out let including grating connecting jointing to waste pipe with lead jointing and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces complete all as specified and as directed .

Disconnecting following size of existing tanks, stacking safely for re-use (or lowering if required) and hoisting, reconnecting and refixing in position complete all as specified. (a) up to 1000 litres capacity.

Taking up or down steel tubing and connections, including cleaning serviceable pipe for refixing and balance under schedule of credit all as specified and directed

(a)15mm bore

(b) 20 mm bore

S&F GI Steel tubing medium grade with all fitting & fixed complete to walls & ceiling or laid in floors complete all as specified for the following size :-

(a)15 mm bore

(b) 20 mm bore

Fixing only GI steel tubing medium grade with all fitting & fixing to walls/ceiling or laid in floor and complete all as specified for the following size :-

(a)15 mm bore

(b) 20 mm bore

Taking down pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc, including cleaning or refixing or removal to store(measured overall as fixed along the centre line over fittings and accessories)

S & F 110mm bore PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

All as per item No. 62.00 above, above but 75mm dia

S&F PVC (SWR) bends of 110mm bore.

S & F 75 mm dia bend

S&F 75mm bore PVC (SWR) branch piece single (Single Y ) equal or unequal

S&F 110mm bore PVC (SWR) branch piece single (Single Y ) equal or unequal

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm. complete all as specified and as directed

M&L for special treatment of sunken portion of WCs and Bath room as per following stages: Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc . Stage 2:- Providing 10mm thick plaster in CM 1:4 with chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd Stage 3:- Applying Dr Fixit Primseal primer or STP Ltd(and allow to dry for 8 hours) under touch dry condition Stage 4:- Applying two coats of water proofing decorative elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP(The surface after painting one coats shall be allowed to dry of 6 hours before next coats) all as per manufacturer instruction Stage 5:-Again rendering 10mm thick in CM 1:4 mixed with Dr Fixit Pidicrete URP or plaster seal of STP Ltd. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP. Stage 7:- Making holes in wall and fixing 600mm long 20mm dia GI spout for draining the surplus water if any.

M & L for cement concrete 1:5:10 Type E2 (using 40mm graded stone aggregate) as in filling in sunken floor etc complete all as specified and directed.

S & F Wash down water closet (Pedestal pattern), complete white (excluding fixing bolts, flushing cisterns and flush pipe) complete all as specified and directed by EIC.

M&L for PCC (1:2:4) type B-0, using 12.5mm graded stone aggregate as in levelling course over RCC roof surface to achieve required slope, benching etc including making rounded or chamfered on edges mixed with WPC as per manufacturer's instructions, complete all as specified and directed.

M&L cement plaster (1:3) with 10 mm thick to be finished smooth without using extra cement mixed with WPC @ 2% by weight of cement, , complete all as specified and directed. Note : WPC shall be measured and paid separately as supply only.

Supply only liquid water proofing compound, complete all as specified and directed.

M & L for APP modified roof treatment over existing roof slab etc including taking down and work to be executed through approved authorised applicator of the membrane manufacturer with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sqm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sq cm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%. (d) Over the membrane provide a finishing with solar reflective bitumen aluminium paint @ 0.10 Kg/Sqm as prescibed by manufacturer.

Dismantling boarding any description fixed in any position with nails complete all as specified and directed .

S&F 18/19 mm thick prelaminated particle board both sides , interior grade , of approved shade and pattern fixed with screws to timber frame with beading piece for cupboard and shelves complete all as specified

S & F for continuous (piano) hinges, mild steel, bright finish or electrogalvanised width of flaps 30mm (when open) complete all as specified and directed.

S & F for 125mm aluminium handles, cast type, anodised complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving not exc 15 cm thick (above or below ground level) and removing the debris outside MD land complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection 75mm thick, with expansion joints & top surface finished even and smooth without using extra cement etc complete all as specified and directed.

M& L for Chequered cement concrete tiles 20cm x 20 cm x 25 mm thick, set, jointed and pointed in neat cement slurry with grey cement and no pigment in floors with mixture of white cement and no pigment over screed bed or bedding layer of 15 mm thick cement mortar 1:6 complete all as specified and directed.

M & L for Antitermite treatment along the external wall below concrete for masonry apron using chemical emulsion @ 2.25 litre per linear meter incl drilling and plugging 12 mm dia holes in appron complete all as specified and directed.

M & L for Antitermite treatment of soil under existing floors using emulsion @ one litre per hole 300 mm drilling apart including drilling and plugging 12 mm dia holes with cement mortar 1;2 (1 cement 2 coarse sand ) to match the existing floors complete all as specified and directed

M & L for treatment at point of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre complete all as specified and directed

M&L for Providing and fixing SS of Grade 304 railling made of hollow tubes channels Plates etc Including welding, grinding, buffing & polishing and making curvature and fitting the same with necessary SS nuts and bolts complete incl fixing with railing with necessary accessories dash fasteners SS bolts of required size on the top of floor or the side of waist slab with suitable arrangements etc complete all as specified and directed.

S & F PVC water tank of capacity 2000 litres including all fittings complete all as specified and directed

SCHEDULE 'A' PART I (E/M WORKS) M & L for point wiring with PVC insulated FRLS unsheathed 1100 Volts grade single core multistranded copper conductor cable 1.5 Sqmm drawn in and including PVC conduit concealed in wall ceiling with all accessories, fittings, PVC junction boxes etc, with suitabe sunk pressed steel boxes for modular fittings not less than 1.6 mm thick, including Modular cover plate of suitable size etc with necessary fixing accessories and earth continuity conductor cable of 1.5 Sqmm size connected to common earth and earth dolly including 1.6 mm thick pressed steel terminal boxes concealed in wall mounting switches / sockets / fan regulators fixed with Cadmium plated machine screws complete including taking down old u/s wiring of any type & including fittings such as ceiling roses, pendants, regulators, sockets, light fittings etc all as specified for one light / fan / bell point controlled by one switch.

-Ditto- all as per item No 88.00 above but for one 5A 2pin/3pin socket out let multipurpose on the same board with other switches.

-Ditto- all as per item No 88.00 above but for one 5A 2pin/3pin switch socket out let multipurpose on independent Board.

-Ditto- all as per item No 88.00 above but wiring complete with 2.5 Sqmm for 3 pin 15A socket multipurpose on independent board

-Ditto- all as per item No 88.00 above but wiring complete with One light point controlled by two 2-way switches, with cables 1.5 sq. mm size complete all as specified and directed.

S&F modular type 6A two way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed.

S&F modular type 6A one way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed.

S&F modular type 2/3 pin combined shuttered type 6 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed.

S&F modular type 2/3 pin combined shuttered typr 16 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed.

S&F modular type 16 A one way SP switch 1 module confirming to IS: 3854-1997 with finguer proof terminal complete all as specified and directed.

S&F modular type 120W step fan regulator of 2 module size conformng to IS: 11037-1984 complete all as specified and directed.

Supply & Fix Modular Bell push flush type 6 Amp, 1 module, 230 Volts complete all as specified and directed.

Supply and fix bell ding dong AC 230 V single pole. complete all as specified and directed.

S & F Modular Blank plate 1 module suitable for Modular switch boards all as specified and as directed

S & F Modular cover plate 12 modules

S & F Modular cover plate 8 modules

S & F Modular cover plate 3 modules

S & F Modular cover plate 2 modules

S & F Modular cover plate 1 module

S&F ceiling rose three terminal, 230 Volts PVC / Polycarbonate body, complete all as specified and directed.

S&F in Repairs/Replacement Surface and wall mounted Pre-coated CRCA housing box type suitable for T8 LED tube light 18/20 watts, 230 volts, End caps made up with engineering plastic & 1.5 sqmm 3 core PVC insulated copper conductor cable including fixing arrangements and taking down old rusted bracket fittings complete all as specified and directed. Make : Bajaj - BLRB-DB 118 I or equivalent of Crompton/wipro/Jaquar

S&F in repairs Highly effcient ULTRON LED tube with Polycarbonate T8 housing designed for high performance 18/20 Watt with in built driver with metal heat sink, double sided connection, 230 volts including fixing arrangements and taking down old unserviceable tube rod complete all as specified and directed. Make : Bajaj - BLRB 18W CW LED or equivalent of Crompton/wipro/Jaquar Note : LM 79 & LM 80 Test certificate from NABL certified Lab shall be submitted by the contractor for LED luminaire along with warranty certificate for 3 years from OEM

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC made out of engineering plastic batten with white acrylic cover sleek designb& high efficiency for wall & surface mounted applications comprising with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make : Bajaj Cat No. BLRB 20 CW LED/ Halonix Cat No. HLB-07-10-CW-IP or Equivalent Note : LM 79 & LM 80 Test certificate from NABL certified Lab shall be submitted by the contractor for LED luminaire along with warranty certificate for 3 years from OEM

S & F LED light fitting 1X10W Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make - Bajaj Cat No. BIBWP 10W LED/ Halonix Cat No. HLBH-02-10-CW or Equivalent Note : LM 79 & LM 80 Test certificate from NABL certified Lab shall be submitted by the contractor for LED luminaire along with warranty certificate for 3 years from OEM

S & F Angular Holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings etc. all as specified and directed. Make : Anchor/ Leader/ Maru

S & F LED Light Bulb 8/9 watt, Pin type of white colour, 230 V complete all as specified and directed. Make : Wipro/ Bajaj/ Philips

Taking down old unserviceable ceiling fan 1200 mm sweep by disconnecting the electric power supply, unscrewing the bolts and nuts, removing the blades and transporting to workshop to undertake repairs by rewinding of burnt out winding using suitable gauge copper wire, replacement of worn out capacitor 2.5 mfd - 01 No., PVC canopy - 02 No's and bearing including scrapping of old paint and applying two coats of synthetic enamelled white paint over a coat of red oxide primer complete and refixing back at site complete all as directed.

Taking down old unserviceable Exhaust fan 300 mm sweep by disconnecting the electric power supply, unscrewing the bolts and nuts, removing the blades and transporting to workshop to undertake repairs by rewinding of burnt out winding using suitable gauge copper wire and bearing including scrapping of old paint and applying two coats of synthetic enamelled grey paint over a coat of red oxide primer complete and refixing back at site complete all as directed.

Supply & fix Heavy Duty metallic Exhaust fan high speed type of sweep 300 mm, speed 1400 RPM, air delivery 1300CMH, power 70W (approx) comprising of double ball bearing, blades,louvers complete mounting anchor fasteners, aluminium louvers made of aluminium sheet of 0.5 mm thickness, provision of three core 1.5 Sqmm PVC insulated copper cable from ceiling rose to fan etc complete all as specified and directed. Make-:Crompton/ Orient/ Almonard/ Bajaj Note -: The Contractor shall submit 1 years warranty certificate from OEM of exhaust fan.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed. Make :- Almonard/ Orient/ Bajaj

S&F single pole and neutral enclosure with a two pin and earth and metal clad plug socket complete with one single pole MCB 20 Amp 240 Volts complete all as specified including concealing in wall and directed. Make :- LEGRAND/ SCHEINDER/ L&T

S & F MCB DB, 12 way, SPN, double door, 240 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections complete including taking down old u/s DB's all as specified and directed. Make : Legrand/ L&T/ Schneider Note: Quoted rate shall be deemed to include for provision of copper bus bar of 200 Amps rating.

S & F MCB SPN 40 Amps, 240 / 415 Volts, 50 Hz, 10 KA Breaking capacity 'C' Series complete all as specified and directed. Make - Legrand/ L&T/ Schneider

S & F MCB SP 5 to 32 Amps, 240 / 415 Volts, 50 Hz, 10 KA Breaking capacity 'C' Series complete all as specified and directed. Make - Legrand/ L&T/ Schneider

M&L in repairs for sub main wiring with two single core 6.0 Sqmm PVC insulated FRLSH multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 6 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed. (Make :- PRESFIT/ PRECISION - Casing caping), (Make :- FINOLEX/ KEI/ POLYCAB - PVC Copper wire) Note : Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

M&L in repairs for sub main wiring with two single core 4.0 Sqmm PVC insulated FRLSH multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 4 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed. (Make :- PRESFIT/ PRECISION - Casing caping), (Make :- FINOLEX/ KEI/ POLYCAB - PVC Copper wire) Note : Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

M&L in repairs for sub main wiring with two single core 1.5 Sqmm PVC insulated FRLSH multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 1.5 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed. (Make :- PRESFIT/ PRECISION - Casing caping), (Make :- FINOLEX/ KEI/ POLYCAB - PVC Copper wire) Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

Supply and fixing in replacement of LED security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection 4 kv surge in built protection complete all as per directed by Engr- in – charge. Make : Bajaj/Crompton/wipro/Jaquar Note : LM 79 & LM 80 Test certificate from NABL certified Lab shall be submitted by the contractor for LED luminaire along with warranty certificate for 3 years from OEM

S& F in replacement of GI steel tubing medium grade 40 mm dia and length up to 1.5 meter bent to shape of offset angle upto 45degree for fixing of security /street light fittings including MS clamps made of 32mm x5mm flat iron, nuts , bolts, etc all as directed by Engineer in charge. Make : Tata/ Jindal/ BST

Supply and fix indoor type vermin and weatherproof totally inclosed cubical type front operated, sufficient ventilation on sides cubicle type fabricated out of 2 mm thick CRCA sheet duly treated with seven tank process and painted epoxy powder coated siemens grey colour and with industrial type built in locking arrangement. The Panel indoor type cubical panel board IP 52 free standing floor mounted (CPRI approved manufacturers). The panel to be prewired with PVC insulated copper conductors appropriate current carrying capacity for connecting the incoming and out going MCCBs and MCBs. including disconnecting the LT panel and taking down the unserviceable cables and including MCBs. Energy meters of the panel shall be taking down and kept in safe custody for re-installation of site. Disconnecting the incoming and out going cable connection and dismantling the unserviceable conventional type industrial meter board and removing from site for further disposal and making LT UG cable connection complete of suitable size and comprising of following items:-

Excavation in trenches not exceeding 1.50 m wide and n.exc 1.5 m in depth for foundation of poles, cable etc, not exc 10 sqm on plan and getting out in soft/loose soil including taking out brick protection etc complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed.

Removing excavated materials (soils) not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified and directed.

M & L for sand cushioning by spreading in trenches crushed sand by gently by punning down manually as in cable protection all as specified and as directed by Engineer -in-charge. Note: Punned depth only will be measured for payment. Note:Punned depth only will be measured for payment

Supply and laying un-reinforced precast concrete cable cover class LV, type-I, flat size 250 mm x 150 mm x 40 mm laid in trenches all as specified and directed. Make : National/ Mehtab Tiles

Supply and Laying or fixing or passing through pipe, XLPE/PVC insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 25 Sqmm 4 core including necessary connection and providing cable lugs & Glands etc as required complete all as specified and directed.

M&L for cutting existing road/hard and dence soil not exc 45 x 60 cm in wide & depth getting out excaveted materials for laying GI tube; returning filling & well ramming watering finishing surface 10 cm from top using PCC 1:3:6 not less than 4 inch thick; including removal of surplas soil all as per directed.

S&F of HDPE pipe 50 mm dia, PN-10 for laying in ground, road crossing etc for cable protection including necessary fittings, clamps for supports, etc complete all as specified and directed. Make : Prayag/ Sudhakar/ Apollo

M&L for earthing using GI earthing strip 32 x 6mm complete with galvanised steel earth plate electode 600mmx600mmx6mm thick buried directly in ground, earth pit not less than 2.25 meters deep below ground level connection to and including GI strip of size 32x6mm to the extend 7.5 mtr as earth lead by means of GI bolts, Nuts etc. with provision of charcoal and salt all as per electrical plate No 3 of SSR Part I including water arrangement with GI Pipe 20 MM dia (medium Grade), earth lead protection pipe 50mm madium grade with bends, elbow etc. from earth plate to test point, excavation and earth work returning, filling, ramming and removing of soil to distance not exc 50mtr, make good to match with existing surface making PCC pit (Earth chamber) having internal size 30cm x 30cm x 30cm and outer size 60cm x 60cm x 60cm with RCC reinforced cover 50mm thick with one lifting handle made of 8mm dia MS bar funnel wie mesh and testing on completion including making test point on wall as per plate No. 3 of SSR Part I specification all as specified and directed.

Vishal Builders

Joy builders

R.C. Magla and Co.