Increasing Capacity and other work

Amount

Work No. 01 Part-A- Providing following materials by the Contractor.

33 KV ‘XLPE’ C/J Kit 3x300mm² Outdoor

33 KV ‘V’ Type Cross Arm 100x50x6mm, MS Channel ( 7.9 Kg/m)

33 KV Polymer Pin Insulator

Number Plate

Danger Board with Clamp

Barbed wire

Bolts, Nuts, & Washers

X-arm clamp with nut bolt for ST Pole 11 mtr with nut bolt by 50x8 mm MS flat Iron make

X-arm clamp with nut bolt for PCC Pole 9 mtr with nut bolt by 50x8 mm MS flat Iron make

Stay set with Clamp for ST Pole 11mtr. with Nut and Bolt by 50x8 mm MS Flat Iron make.

Stay set with Clamp for PCC Pole 9 mtr with Nut and Bolt by 50x8 mm MS Flat Iron make.

Stay Rod 20x1800 mm

Stay wire 7/8 SWG

MS Earthing Rod 20x2500 mm

33 KV Polymer Disc Insulator 70 KN B&S Type

Disc fitting 70 KN B&S Type for DOG

P.G. Clamp for DOG

‘E’ Bracket for 33 KV

M.S. Angle Iron 65x65x6mm bracing with clamps

33 KV. Top channel ( 125x65mmX3200 mm ( 10.7 Kg/m) with clamps

33 KV Guarding angle

GI Wire 5 mm

33 KV Guarding angle Clamp with nut bolt for ST Pole 11mtr. with Nut and Bolt by 50x8 mm MS Flat Iron make.

33 KV Guarding angle Clamp with nut bolt for PCC Pole 9 mtr. with Nut and Bolt by 50x8 mm MS Flat Iron make.

F-bracket with nut bolt for ST Pole 11 mtr & PCC Pole 9 mtr with nut bolt by 50x8 mm MS flat Iron make

Part-B Work Shifting,loading and carriage of following materials on private truck at store centre Maharajganj & Un-loading of the same with proper stacking at work site .

P.C.C. Pole 9 M long

S.T. Pole – 11 Mtr. Long

33 KV ‘XLPE’ Cable 3x300mm²

ACSR ‘Dog’ Conductor

Laying of 33 KV 3x300 mm² ‘XLPE’ cable of double circuit (220X2 Mtr)cable by digging pit & making trench in Proper size(1.2M depth x1M wide) below ground level by fixing bricks(4½˝)on both side of trench wall and 9˝ brick work at the centre of the trench along the cable.Fixing brick slab on top after filling sand around both the cable including cost of bricks/ HDD Method by drilling machine as per site requirement.

Laying of 33KV ‘XLPE’ cable in air after providing 6” dia. M.S pipe 3 m long Complete work.(Rs 1475/mtr)

Providing & Cable jointing charges of 33 KV XLPE Cable Outdoor.

GI Pipe Earthing Complete for Cable jointing Kit with materials

Fabrication of 13 M long S.T. pole by welding 3.0 M long 5" dia M.S. pipe & Flat Iron 50x6 mm 12" long by providing M.S. pipe and all other materials by the contractor and only S.T. poles 11 Mtr. Long will be provided by the department.

Erection of Single pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories for double circuit ( 'V' type cross arm 100 x 50 x 6 mm, M.S. Channel (7.9 Kg./M) clamps with bolt and nut, composite polymer pin insulator, danger board with clamp, barbed wire earthing, etc. complete as per RESSPO).

Extension of 9 mtr PCC Pole for proper clearence for existing lines by 33 KV Top channel with clamp with complete work as per proper specification.

Erection of Double pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, barbed wire earthing, etc. complete as per RESSPO) .

Erection of Four pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, barbed wire earthing, etc. complete as per RESSPO) .

Erection of Single pole structure on 11mtr ST. (SP-55) Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories for double circuit ( 'V' type cross arm 100 x 50 x 6 mm, M.S. Channel (7.9 Kg./M) clamps with bolt and nut, composite polymer pin, insulator, danger board with clamp, Alluminium paint, red oxide paint, barbed wire earthing, etc. complete as per RESSPO.

Erection of Double pole structure on 11 mtr ST Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Alluminium paint, red oxide paint, barbed wire earthing, etc. complete as per RESSPO) .

Erection of four pole structure on 11 mtr ST Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Alluminium paint, red oxide paint, barbed wire earthing, etc. complete as per RESSPO) .

Laying, spreading, lifting and final sagging of 3 phases of ACSR Dog conductor in accordance with profile and sag chart including binding, Jumpering and fixing of P.G. Clamp as per requirement in 03 Nos. conductor in parallel.

Grouting of stay rods (20 x 1800) mm including all work of excavation, cement concrete in size (0.60 x 0.60 x 0.30) m in ratio 1:4:8 cement, sand, 40mm brick ballast) as per drg including back filling, proper ramming etc. Fixing tightening & nozzling of stay wire with stay rod with the poles of required tension as per drawing.

Painting of S.T Pole 11 mtr. Long with Alluminium paint and red oxide paint etc.

Chopping of branches of trees of eucalyptus, Neem, Keekar and other kind of trees along the route of the line and disposal of the same at suitable place.

Guarding between two poles like single poles, double poles, four poles, dense area etc. to guard LT, 11 KV Line telephone and river crossing, road crossing etc. with G.I. wire no. 6 SWG and G.I. wire no. 8 SWG, cutting, fabrication and fixing of guarding channel 75 x 40 x 3010 mm with clamps nut & bolts etc. as per drawing.

Work No. 02 Part-A- Providing following materials by the Contractor.

33 KV ‘XLPE’ C/J Kit 3x300mm² Outdoor

33KV ‘V’ Type Cross Arm 100x50x6mm, MS Channel ( 7.9 Kg/m)

33 KV Polymer Pin Insulator

Number Plate

Danger Board with Clamp

Barbed wire

Bolts, Nuts, & Washers

X-arm clamp with nut bolt for ST Pole 11 mtr with nut bolt by 50x8 mm MS flat Iron make

X-arm clamp with nut bolt for PCC Pole 9 mtr with nut bolt by 50x8 mm MS flat Iron make

Stay set with Clamp for ST Pole 11mtr. with Nut and Bolt by 50x8 mm MS Flat Iron make.

Stay set with Clamp for PCC Pole 9 mtr with Nut and Bolt by 50x8 mm MS Flat Iron make.

Stay Rod 20x1800 mm

Stay wire 7/8 SWG

MS Earthing Rod 20x2500 mm

33 KV Polymer Disc Insulator 70 KN B&S Type

Disc fitting 70 KN B&S Type for DOG

P.G. Clamp for DOG

‘E’ Bracket for 33 KV

M.S. Angle Iron 65x65x6mm bracing with clamps

33 KV. Top channel ( 125x65mmX3200 mm ( 10.7 Kg/m) with clamps

33 KV Guarding angle

GI Wire 5 mm

33 KV Guarding angle Clamp with nut bolt for ST Pole 11mtr. with Nut and Bolt by 50x8 mm MS Flat Iron make.

33 KV Guarding angle Clamp with nut bolt for PCC Pole 9 mtr. with Nut and Bolt by 50x8 mm MS Flat Iron make.

F-bracket with nut bolt for ST Pole 11 mtr & PCC Pole 9 mtr with nut bolt by 50x8 mm MS flat Iron make

Part B Work Shifting,loading and carriage of following materials on private truck at store centre Maharajganj & Un-loading of the same with proper stacking at work site .

P.C.C. Pole 9 M long

S.T. Pole – 11 Mtr. Long

33 KV ‘XLPE’ Cable 3x300mm²

ACSR ‘Dog’ Conductor

Laying of 33 KV 3x300 mm² ‘XLPE’ cable of double circuit by digging pit & making trench in Proper size(1.2M depth x1M wide) below ground level by fixing bricks(4½˝)on both side of trench wall and 9˝ brick work at the centre of the trench along the cable.Fixing brick slab on top after filling sand around both the cable including cost of bricks/ HDD Method by drilling machine as per site requirement.

Laying of 33KV ‘XLPE’ cable in air after providing 6” dia. M.S pipe 3 m long Complete work.(Rs 1475/mtr)

Providing & Cable jointing charges of 33 KV XLPE Cable Outdoor.

GI Pipe Earthing Complete for Cable jointing Kit with materials

Fabrication of 13 M long S.T. pole by welding 3.0 M long 5" dia M.S. pipe & Flat Iron 50x6 mm 12" long by providing M.S. pipe and all other materials by the contractor and only S.T. poles 11 Mtr. Long will be provided by the department.

Erection of Single pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories for double circuit ( 'V' type cross arm 100 x 50 x 6 mm, M.S. Channel (7.9 Kg./M) clamps with bolt and nut, composite polymer pin insulator, danger board with clamp, barbed wire earthing, etc. complete as per RESSPO).

Extension of 9 mtr PCC Pole for proper clearence for existing lines by 33 KV Top channel with clamp with complete work as per proper specification.

Erection of Double pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, barbed wire earthing, etc. complete as per RESSPO) .

Erection of Four pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, barbed wire earthing, etc. complete as per RESSPO) .

Erection of Single pole structure on 11mtr ST. (SP-55) Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories for double circuit ( 'V' type cross arm 100 x 50 x 6 mm, M.S. Channel (7.9 Kg./M) clamps with bolt and nut, composite polymer pin, insulator, danger board with clamp, Alluminium paint, red oxide paint, barbed wire earthing, etc. complete as per RESSPO.

Erection of Double pole structure on 11 mtr ST Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Alluminium paint, red oxide paint, barbed wire earthing, etc. complete as per RESSPO) .

Erection of four pole structure on 11 mtr ST Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above , grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast),back filling of earth ,proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Alluminium paint, red oxide paint, barbed wire earthing, etc. complete as per RESSPO) .

Laying, spreading, lifting and final sagging of 3 phases of ACSR Dog conductor in accordance with profile and sag chart including binding, Jumpering and fixing of P.G. Clamp as per requirement in 03 Nos. conductor in parallel.

Grouting of stay rods (20 x 1800) mm including all work of excavation, cement concrete in size (0.60 x 0.60 x 0.30) m in ratio 1:4:8 cement, sand, 40mm brick ballast) as per drg including back filling, proper ramming etc. Fixing tightening & nozzling of stay wire with stay rod with the poles of required tension as per drawing.

Painting of S.T Pole 11 mtr. Long with Alluminium paint and red oxide paint etc.

Chopping of branches of trees of eucalyptus, Neem, Keekar and other kind of trees along the route of the line and disposal of the same at suitable place.

Guarding between two poles like single poles, double poles, four poles, etc. to guard LT, 11 KV Line telephone and river crossing, road crossing etc. with G.I. wire no. 6 SWG and G.I. wire no. 8 SWG, cutting, fabrication and fixing of guarding channel 75 x 40 x 3010 mm with clamps nut & bolts etc. as per drawing.

Work No. 03 Shifting & loading of following materials on private truck at store centre Maharajganj & carriage up to 33/11 KV Sub-Station Koluhi, Distt- Maharajganj & Un-loading of the same with proper stacking (Distance about 0 to 55 km)

11 KV ‘XLPE’ power cable.

33 KV ‘VCB’ complete with all structure.

33 KV C.T.Structure

33 KV Fuse Set

33 Line Type Isolator

33 Bus Type Isolator

33 KV Post Insulator

Structure for Above

33 KV Single T/F Control pannel

33 KV lightening arrester

33 KV LA Structure.

Repairing of plinth and foundation for 10 MVA transformer as per required specification. Dismantling of T/F all connection.

Dismentling of existing 2 no body and 1 no Neutral earthing safely of existing 5 MVA power transformer earthing for installation of new 10 MVA T/F and re-earthing of new 10 MVA T/F by old earth strip including providing required length of GI Earth strip .The earthing of 10 MVA T/F Included all work completed as per required specification of RESSPO norms.

Providing 33 KV. Top channel for cable stand & neutral earthing

Dismentling of HT jumpers, 11 KV C/J kit and different earthing of 5 MVA T/F drain out T/F oil after closing valve and opening of radiator for shifting of existing 5 MVA T/F from plinth about 30 mtr. Distance & resetting of All accessories etc. complete work.

Digging of pit for taking out of old & used running condition 11 KV cable safely.

Grouting of M.S. channel 3.2 mtr long for cable stand and welding of M.S. flat at equal distance for fastening cable by clamp with nuts and bolts mounting of cable at cable stand and connection of jumpers.

Providing & Jointing charges of 11 KV “XLPE” C/J kit 3 x 300 mm2 Indoor/Outdoor type

Laying of 11 KV “XLPE” power cable 3 x 300/185 mm2 including digging of pits of size 0.5 x 0.5 mtr. covering of cable with sand and 1st class brick around the cable.

Laying of 11KV ‘XLPE’ cable in air after providing 6” dia. M.S pipe 3 m long Complete work.

GI Pipe Earthing Complete for Cable jointing Kit with materials

Neutral earthing of 10 MVA T/F Complete including cost of GI Strip, GI Pipe 1.5" dia and 30' long and other earthing materials(Delta type).

Providing and Making connection of 24 Volt battery and battery charger with cabinet.

Jumpring from 33 KV Bus bar to post insulator, bus isolator, VCB, CT and LA to 10 MVA transformer etc.( Providing alluminium Lug and PG Clamp)

Installation of 33 KV control panel for “VCB” with complete earthing with installation of battery and battery charger in control room and making connection.

Erection,Installation and grouting of “VCB” Structure mounting and fitting of “VCB” on erected structure with complete earthing.

Erection,Installation and grouting of “CT” Structure mounting and fitting of “CT” on erected structure with complete earthing.

Erection,Installation and grounting of Fuse Set structure. mounting and fitting of Fuse Set on erected structure with complete earthing.

Erection,Installation and grounting of LA structure. mounting and fitting of LA on erected structure with complete earthing.

Mounting and fitting of equipment on erected structures.

33 KV line isolator 400 Amp

33 KV Bus – Isolator 400 Amp.

33 KV Post Insulator

Painting of erected structure in switchyard (Applying on coat of good quality red oxide primer then two coat of good quality of high class luxol aluminium paint)

Providing following control cable and its laying from switchyard to control room 33 KV panel by digging trench in switchyard including cost of sand and 1st class bricks with covering and making connection complete and including cost of laying.

Size 2 x 2.5 mm2

Size 4 x 2.5 mm2

Dismantling of existing pale fencing and resetting after completion of transformer work.

Carriage of old and used 11 KV ‘XLPE’ power cable from 33/11 KV Sub-Station Koluhi, Distt-Maharajganj to store center Maharajganj

Akash Traders

INDIA SUPPY CORPORATION