SPECIAL REPAIR TO BLDG NO. NP-46 AND PROVN OF URINAL/ TOILET BLOCKS INLUDING CERTAIN REVENUE WORK AND MINOR WORK UNDER AGE B/R-I AND AGE E/M OF GE (WEST) PATHANKOT

Amount

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete over screed bed or bedding layer 20 mm thick in cement mortar 1:6 complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Dismantling of floor hearth and wall tiling incl cement morter bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for coloured joint free Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) are of each tile exc 0.11 Sqm but n. Exc. 0.18 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or bedding layer with CM 1:6 complete all as specified and directed.

M & L for coloured Glazed ceramic tiles in vertical surfaces 350 x 250 x 7mm/450 x 350 x 7mm set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

Demolition of concrete of any description and in any position not otherwise specifically provided for (cinder concrete/lean concrete in Sunken floor) complete all as specified and as directed.

M & L for providing water proofing treatment with APP based polymeric membrane minimum weight 3 Kg/sqm and minimum thickness 3mm, reinforced with polyester non woven fabric (weight not less than 150gm/sqm) applied over one coat of oil based bitumen emulsion primer @ 0.3 liter/sqm(or as per the manufacturer instructions) including cleaning of surface throughly from dust, dirt and dismantling of old membrane any type and providing 15mm thick rendering in CM 1:4 with WPC (as per manufacturer instructions) followed by new membrane with torch application with 10 cm overlaps on sides and end joints. A coat of blown bitumen 85/25 @ 1.2 kg/sqm to be applied on top of memberane and providing 25 mm thick sand cushioning to recieve lean concrete in sunken floor complete all as specified and directed. Note:- 1. WPC will be measured and paid separately. 2. Membrane and bitumen primer should be the same manufacturers.

M & L for PCC (1:5:10) type E2 (using 40 mm graded stone aggregate) as in filling and mass concrete complete, all as directed and as specified.

M & L for 25mm thick plain cement concrete (1:2:4) type B0 using 12.5 mm graded agg as in levelling course complete all as specified and directed.

M & L for providing water proofing treatment with APP based polymeric membrane minimum weight 3 Kg/sqm and minimum thickness 3mm, reinforced with polyester non woven fabric (weight not less than 150gm/sqm) applied over one coat of oil based bitumen emulsion primer @ 0.3 liter/sqm(or as per the manufacturer instructions) including cleaning of surface throughly from dust and dirt and providing 15mm thick rendering in CM 1:4 with WPC (as per manufacturer instructions) followed by new membrane with torch application with 10 cm overlaps on sides and end joints. Finally painting the surface with bituminous aluminium paint @ 100gm/sqm complete all as specified and directed. Note:- 1. WPC will be measured and paid separately. 2. Membrane and bitumen primer should be the same manufacturers.

Supply only liquid water proofing compound complete all as specified and directed.

Dismantling stone slabs and tiles laid dry or laid dry and pointed any description or thickness in floors, aprons etc complete all as specified and directed.

M & L for 25mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Demolition of stone/brick masonry in CM or cement/ lime mortar complete all as specified and directed.

M & L for Brickwork with sub-class `B’ burnt bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

M & L for brick work with sub class ‘B’ burnt old size brick, straight or curved on plan exc 6.0 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for brick work with fly ash old size bricks,straight or curved on plan exc 6m mean radius built in CM 1:6 complrte all as specified and as directed.

M & L for brick work with fly ash old size brick having crushing strength not less than 75Kg/sqcm, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 complete all as specified and as directed.

M & L for brickwork with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4, surfaces finished even and smooth(without using extra cement) complete all as specified and directed.

M & L for rendering 15 mm thick on other than fair faces of brick surfaces/stone masonry in cement mortar (1:6) finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 5 mm thick on chajjas, facias, ceiling and the like in cement mortar (1:3), finished even and smooth on new concrete surfaces, complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including mixing of liquid water proofing admixture in the proportion as mentioned in manufacturer's instructions, complete all as specified and as directed. Note:- Water Proofing Admixture to be measured & paid for separately as supply only.

Taking down chowkat or frames with shutter (W/O taking of shutter from the frame) area exc 1.5 Sqm but n. exc 4.0 sqm each complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be coucred with heat moulded wood grain printed PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail & bottom rail on either side as gap insert for top rail bottom rail panelling of wood grain printed PVC sheet to be fited in the MS frame welded/seald to the stiles & rails with suitable PVC sheet beading and jointed together with saluent cement suppling & fixed in the framed site as per specification & drawing.

S & F of PVC door frame of size 50mmx47mm made out of 5mm wood grain printed PVC sheet reiforced with MS squre tube complete as per specification, drawing and as per directed.

S & F of Aluminium anodised barrel tower bolts of extruded section 125mm long complete all as specified and directed.

S & F of Aluminium handles cast type anodised of 125mm complete all as specified and directed.

S&F butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 100mm size complete all as specified and directed.

S & F steel window/Ventilator factory made out of box type and shutter (double shutter) with sash bar made out of section using flash butt welding, hinges shall be provided to both shutters complete including all fittings including grills(12mm sq bar), glazing(3mm thick sheet glass), guaging(0.56mm nominal dia of wire and average width of aperture 1.18mm) and two coat synthetic enamel paint over a coat of red oxide primer all as per drg No CEPZ/TD/245/01 Sh 1/1, CEPZ-TD/246/01 Sheet 1/2 and Sheet 2/2 all as specified and directed by Engr-in-Charge.

Taking down eves gutter and rain water pipes (any size or pattern), including all fittings, head shoes, bends, swan-necks atc., incl cleaning or refixing or removal to store (mesured overall as fixed along the centre line over fittings the accessories) complete all as specified and directed.

S & F cast iron soil, waste and vent spun pipes 100 mm bore in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S & F cast iron soil, waste and vent spun pipes 75 mm bore in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

S & F 100 mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S & F 75 mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S & F 100mm bore cast iron bends (any radius) with duck’s foot or heel rest complete all as specified and directed.

S & F 75mm bore cast iron bends (any radius) with duck’s foot or heel rest complete all as specified and directed.

S & F 100 mm bore stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S & F 75 mm bore stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

M & L for 100 mm caast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified and directed.

M & L for 75 mm cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified and directed.

M & L for extra over cast iron 100 mm bore pipes and fittings if lead joint is provided in lieu of cement joint complete all as specified and directed.

M & L for extra over cast iron 75 mm bore pipes and fittings if lead joint is provided in lieu of cement joint complete all as specified and directed.

Taking up or down steel tubing 15mm bore and connections, including removal complete all as specified and directed.

Taking up or down steel tubing 20mm bore and connections, including removal complete all as specified and directed.

S&F of 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed.

S&F of 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floor complete all as specified and directed.

S & F in repairs vitreous china wash down water closet pan (Pedestal Pattern ) white including fixing bolts, plastic water closet seat, white, closed pattern, solid type with flat bottom, and cover and mild steel chromium plated hinging device complete and including making good to floor to match with adjoining surfaces complete all as specified and as directed

S & F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including provision of lime concrete bedding, making good to floor and all fittings (excluding flushing cistern and flush pipe) complete all as specified and as directed.

S & F in repairs PVC 10 ltrs capacity valveless symphonic action type low level flushing cistern including flush pipe, cantilever brackets incluiding taking down existing cistern etc complete all as specified and as directed

S&F in repairs vitreous china under counter wash basin with fixing accessories, oval shape white of size 595 x 420 x 200 mm, incl 32mm dia brass chromium plated waste coupling (Make :ALD-705 of Jaquar or Technocommercially equivalent in any of the make mentioned in list of products.) and cast iron brackets complete all as specified and as directed. Make : CNS-WHT-705 of Jaquar or Technocommercially equivalent in any of the make mentioned in list of products.

S & F Vitreous China urinal, half stall type white with CP grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in white cement complete all as specified and as directed.

S & F in repairs vitreous China urinal partition wall complete all as specified and as directed.

S&F of CP Pillar taps 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repair angle valve/stop cock, chromium plated with Chromium head and wall flange suiable for 15mm bore fancy type, high pressure complete all as specified and as directed.

S&F of angle valve/stop cock, chromium plated with Chromium head and wall flange suiable for 15mm bore fancy type, high pressure complete all as specified and as directed.

S&F of stop valve fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) capstan head serewed down for 15 mm dia iron pipe complete all as specified and as directed.

S & F in repair push cock fancy type cast copper alloy, chromium plated serewed down for 15 mm dia iron pipe complete all as specified and as directed.

S & F stainless steel jet with 1.0m long flexible PVC tube suitable to fix in the pedestal pan closet complete all as specified and as directed.

S & F in repairs brass chromium plated two in one tap screwed for 15mm dia bore iron pipe complete all as specified and directad Make: FLR-5041N of Jaquar or Technocommercially equivalent in any of the make mentioned in list of products.

S & F brass chromium plated two in one tap screwed for 15mm dia bore iron pipe complete all as specified and directad Make: FLR-5041N of Jaquar or Technocommercially equivalent in any of the make mentioned in list of products.

S & F 15mm bore dia of pipe bib taps cast copper alloy, fancy type chromium plated, with capstan head screwed down, screwed for iron pipe of brass ferrule complete all as specified and as directed.

S & F urinal spreader cast copper alloy chromium plated for fixing with 15 mm dia pipe complete all as specified and directed.

S & F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S & F in repairs CP Grating with hole /with out hole of dia 125 mm complete all as directed in repairs

S & F PTMT grating doom with hole /with out hole 100 mm dia PTMT (Min wt. 25gms) complete all specified and as directed.

S & F brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges all as specified and directed.

S & F swivel shower of PTMT any colour for fixing with 15mm pipe.(minimum weight 40 gms) complete all as specified and directed.

S & F shower arm 15mm size,195mm long with bend of 45degree with flange of PTMT any colour complete all as specified and directed. (Minimum weight 40gms)

S & F shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and directed. (Minimumweight300gms)

S & F in repairs looking mirror of size 900mm x 600mm, 4.0 mm thick mounted 6mm thick plywood/asbestos sheet building board complete all as specified and as directed.

S&F of rotational moulded polythylene water storage tanks (cylindrical vertical) triple layered ISI marked with closed top hosted and fixed in position all as specified 500 liter capcity complete all as specified and directed.

S&F of rotational moulded polythylene water storage tanks (cylindrical vertical) triple layered ISI marked with closed top hosted and fixed in position all as specified 1000 liter capcity complete all as specified and directed.

S & F for gun metal, globe or gate valves for 20mm bore pipe with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S & F for PVC ball valves high pressure with epoxy coated aluminium rod & high density plastic ball screwed for 20 mm bore iron pipe and fixed complete all as specified and directed. (Minimum weight 20mm-210gms)

M & L PVC (SWR) floor trap 75mm diameter of outlet,plain with grating incl jointing with solvent cement complete all as specified and directed.

M & L PVC (SWR) multi floor trap 75mm diameter of outlet, with grating incl jointing with solvent cement complete all as specified and directed.

S & F PVC (SWR) pipes 75mm dia single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S & F PVC (SWR) bends any radious 75 mm dia complete all as specified and directed.

S & F PVC (SWR) 75mm bore 'T' equal or unequal complete all as specified and directed.

S & F PVC (SWR) 110mm bore 'T' equal or unequal with access door complete all as specified and directed.

S & F PVC (SWR)vent cowl of 110 mm bore complete all as specified and directed.

S & F PVC (SWR) bends any radious 110 mm dia complete all as specified and directed.

S & F PVC (SWR) bends any radious 75 mm dia with access door complete all as specified and directed.

Excavation in any type of soil for post holes (or similar holes) each not exceeding 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface complete all as specified and directed.

S & F rolled mild steel section as in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410-W(Gde-E-250) quality-A complete all as specified and directed.

Fixing only chain link MS galvanised fencing mesh size 75mm x 75mm made with 3mm dia GI wire including line wires any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and directed.

Supply only chainlink MS galvanised fencing, any size or type complete all as specified and directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for mild Steel round bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete Fe-410-W(Gde E-250) quality-A or Fe 290 (Gde-E-165) complete all as specified and directed.

S & F Galvanized, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of posts, straining bolts,standard bolt, including securing or tying at crossing with and including provision of galvanized mild steel wire staples or steel pins, etc complete all as specified and directed (Each line of wire to be measured for the purpose of payment).

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm not exc 10 cm long and 11 to 15 mm dia of shank complete all as specified and directed.

S & F hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

M&L for Punched tape concertina coil of 730 mm dia, 56 loops, 2.5mm core wire, heavy galvanised (wire-275 GSM), tensile strength of wire 1400-1500 N/Sqmm, weight 11.00 Kg/coil, stretchable length 10.0 m including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and as directed.

M&L for two coat of synthetic enamel painting over and including a coat of red oxide including preparation of new steel surface not exc. 10cm in width and girth complete all as specified and directed.

M&L preparation of new steel surface of any description, over 10cm in width or girth not other wise described and applying two coat of synthetic enamel paint over and including a coat of red oxide primer complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

M&L for Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying of cables and pipes etc. n exc 10 sq m on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified and directed.

Returning filling in and including spreading, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed.

Removing excavated material (soil) to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for Earth filling spreading and levelling in layers n exc 25 cm thick and well ramming incl watering as required complete all as specified and directed.

M & L for Cement Concrete 1:4:8 type D-2 using 40mm grded crushed stone agg as in fdn filling and mass concrete complete all as specified and directed.

M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 6 m to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per srl item No. 107.00 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for RCC (nominal mix), type B1 (1:2:4) using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M & L for RCC (nominal mix) type B-1, (1:2:4) using 20 mm graded stone aggregate as in chajjas and the like complete all as specified and directed.

M & L for RCC (nominal mix) type B-1, (1:2:4) using 20 mm graded stone aggregate as in beams, cantilevers lintel over 1.5 m long span and the like complete all as specified and directed.

M & L for RCC (nominal mix) type B1(1:2:4) 20 mm graded stone aggregateas in slab supported on wall , beams and columns in floors, balconies, canopies, deck slabs and in shelves and like etc complete all as specified and directed.

M & L for RCC M-25 (Design mix) using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M & L for RCC M-25 (Design mix) using 20 mm graded stone aggregate as in chajjas and the like complete all as specified and as directed.

M & L for RCC M-25 (Design mix) using 20 mm graded stone aggregate as in beams, cantilevers lintel over 1.5 m long span and the like complete all as specified complete all as specified and as directed.

M & L for RCC M-25 (Design mix) using 20 mm graded stone aggregate as in column, pillar, post etc. complete all as specified an as directed.

M & L for RCC M-25 (Design mix) using 20 mm graded stone aggregateas in slab supported on walls , beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and as directed.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and directed.

M & L for formwork to chullah hoods, chajjas, troughs and similar items including edges with rough finished flat surfaces of concrete, complete all as specified and directed.

M & L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide with rough finished flat surfaces of concrete, complete all as specified and directed.

M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. ; with rough finished flat surfaces of concrete, complete all as specified and as directed.

M & L for formwork to sides of square or rectangular pillars, posts, struts, piers, columns and stanchions with rough finished flat surfaces of concrete, complete all as specified and as directed.

M & L for preparation of new plastered surfaces of wall and applying two coat of cement base paint over a coat of primer/chalk whiting of any colour complete all as specified and as directed

M & L for preparation of new undecorated plastered or un plastered surfaces of walls and applying three coat of white wash on walls complete all as specified and as directed

M & L for preparation of new undecorated plastered or un plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed

M & L for 75mm thick Cement Concrete 1:4:8, type D-2, using 40mm graded stone aggregate as in sub base complete all as specified and directed.

M & L for hardcore of broken stone boulders gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6 type C-1 (20mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and as directed.

Concrete bed to 150mm bore drain pipes including packing under and hunching against the sides of pipes after they are laid and tested, in cement concrete M-7.5 (Nominal mix) type D-2 (using 40mm graded crushed stone aggregates) complete all as specified and as directed.

Unplasticisted PVC drainage pipe 160mm dia type 'B' with wall thickness 4mm (min) of pressure rating 4KN/Sqm laid in tranches and jointed with cement solvent including testing complete all as specified and directed complete all as specified and directed.

M&L for 150mm dia reinforced concrete pipes Class NP-2, laid and jointed complete with collars complete all as specified and directed.

M&L for Cement concrete M-15 (Nominal mix) type B-1 using 20mm graded crushed stone aggregate as in coping, benching and the like including weathering, slightly rounded or chamfered angles as directed including necessary form work and finishing all exposed surfaces, complete all as specified and as directed.

M&L for Precast RCC 1:2:4, type B1 (using 20mm graded aggregate) as in cover slabs for Man holes etc set in CM 1:4 complete all as specified and as directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

M&L for mild steel work as in frame for man hole covers complete all as specified and directed

M&L for Septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, fly ash brick work , RCC M-25 Design Mix in Walls , Base Slab , Baffle walls and Roof Slab including beams etc with vent shaft , manhole openings with cover connection etc., complete with effective depth of 1.5 meter and overall depth of 3 meter for 25 user as shown in Drg no CEPZ/C-TD/013/13 sheet 3/5 complete all as specified and as directed.

M&L for Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 2.4 M dia X 3.0 M effective depth as shown in Drg no CEPZ/C-TD/013/13 sheet 1/5 complete all as specified and as directed.

M & L for chequred cement concrete tiles 30 cm x 30 cm x 25mm thick , set, jointed and pointed in neat cement slurry in floors with grey cement and pigments over and including 20 mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes complete all as secified and as directed.

M & L for machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade with grey cement and no pigment complete all as secified and as directed.

M & L for sand filling under floors or in foundations including watering and consolidation complete all as secified and as directed.

M & L for point wiring for one light/one fan controlled by one switch with 1.5 PVC insulated unsheathed multistrand copper conductor FRLS cable with and including PVC concealed conduit heavy duty 20 mm dia having thickness not less than 1.8 mm with all fittings including anodised pressed steel sunken box having thickness not less than 2mm with 3mm thick bakelite laminated sheet ISI marked for switches and sockets , including 1.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly, including cutting chiseling for concealed piping and making good disturbed surface to match with the existing surface complete all as specified and directed.Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green).

M & L for point wiring with 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable with in and including PVC concealed conduit heavy duty 20mm dia having thickness not less than 1.8 mm with all fittings including anodised pressed steel sunken box having thickness not less than 2mm with 3mm thick bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed. Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black,Earth- Green).

S & F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S & F switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

S & F socket outlet 2 in 1, 5 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S & F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

S & F ceiling rose 65 x 50mm three terminals complete all as specified and directed.

S & F of LED Lamp, B22 type ,14 watt,complete all as specified and directed.

S & F energy saving decorative LED box type (4 Feet), 230 volts, light fitting extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories prewired without tube and making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as spd and directed by Engr -in -charge.Make of LED Fitting:- CROMPTON DMLN1LT8-16 or Technocommercially equivalent in any of the make mentioned in list of products.

S & F energy saving LED rod 20 watt (4 feet), 230 volts, 6500 K energy efficient tube light complete all as spd and directed. Make of LED Rod:- CROMPTON LTT8-20 or Technocommercially equivalent in any of the make mentioned in list of products.

M & L for providing/ cutting the round/ square hole of required size in wall finishing the distrubed surfaces as per existing finishes complete all as spd and supply and fixing propeller PVC type AC ventilating fans, Single phase, 230 volts 150 mm sweep complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated three core 1.5 sqmm copper cable FRLS from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as spd and directed by Engr-in-charge.

S & F of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 4 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S&F of MCB SP 240 volts any rating from 6 to 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F of MCB SPN 240 volts any rating from 6 to 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S & F bldg secuirty light fitting energy saving high efficiency LED street light fitting 25 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 32 mm dia bent to shape having length not less than 1.5 mtr fixing with clamp etc and making connections using cord flexible 3 core copper cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage. Make: CROMPTON CAT REF. LSTS-25-CDL or technocommercially equivalent in any of the make mentioned in list of products.

M & L for earthing complete with galvanised steel earth plate electrode , 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point , GI tubing 15 mm bore light grade protection pipe , GI watering pipe 20mm bore light grade with funnel and wire mesh, 15mm thick layer of charcoal & salt packed around the earth plate includeing PCC (1:2:4) pit and 4 cm thick cover of precast RCC 1:2:4 (Nominal mix ) reinforced with XPM having weight not less than 4 kg /sqm including suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover including earth work in any type of soil , removal of surplus soil to a distance n.exc 50m, RFR and connecting , testing on completion complete all as shown on electric plate No 03 of SSR -2009 Part I complete all as specified and directed.(Note: Excavation and earth work is deemed to be included in the rates quoted).

Supply, laying & testing of XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 Volts grade, of size 16 Sqmm 2 core complete all as specified and directed. Note:- Earth work including excavation, returning filling , removing, sand cushioning, GI pipe,brick covering for mechanical protection of cable etc will be measured and paid separately under respective items of schedule.

Supply, laying & testing of XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 Volts grade, of size 10 Sqmm 2 core complete all as specified and directed. Note:- Earth work including excavation, returning filling , removing, sand cushioning, GI pipe,brick covering for mechanical protection of cable etc will be measured and paid separately under respective items of schedule.

Sand cushioning for under ground cable upto 8 cm before laying the cable and 15 cm after laying and stretching the cable and punned down to form a bed. The punning upto 18 cm shall be done by hand complete all as specified and directed. Punned thickness 18 cm shall be considered for payment purpose.

Material and labour for sub class 'B' bricks well burnt old size laid dry flat perpendicular to the length of cable for protection of cable complete all as specified and directed.

Supply and fixing of GI tubing medium grade of 40 mm nominal bore of pipe in trenches/under roads/ under culverts/under paths/under floor/on walls /with pole in new position with screwed sockets joints, together with all tube fittings (such as bends, elbow, tees, short places connections back nuts, diminishing places, caps, plugs and union etc) complete all as specified and directed .

Material & labour for Cutting existing steel tubing 50/40/25/20mm dia for alterations or additions (Each cut measured) including threading of existing pipes placing new Tee of required size tapping connection for new pipe line complete all as specified and directed. (cost should be inclusive of earthwork)

Supply, laying & testing GI water tubing 20 mm bore medium grade, ISI marked with screw and socket joints with all fittings, fixtures like bend, sockets, union, nipple etc laid in trenches or floors, complete all as specified and directed.

All as per Srl item no. 163.00 here-in-before but 15mm bore complete all as specified and directed.

S & F gun metal gate valve for 15mm bore pipe with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Supply and fixing of GI tubing medium grade of 40 mm nominal bore of pipe in trenches/under roads/ under culverts/under paths/under floor/on walls /with pole in new position with screwed sockets joints, together with all tube fittings (such as bends, elbow, tees, short places connections back nuts, diminishing places, caps, plugs and union etc) complete all as specified and directed .

Material & labour for Cutting existing steel tubing 50/40/25/20mm dia for alterations or additions (Each cut measured) including threading of existing pipes placing new Tee of required size tapping connection for new pipe line complete all as specified and directed. (cost should be inclusive of earthwork)

Supply, laying & testing GI water tubing 20 mm bore medium grade, ISI marked with screw and socket joints with all fittings, fixtures like bend, sockets, union, nipple etc laid in trenches or floors, complete all as specified and directed.

All as per Srl item no. 168.00 here-in-before but 15mm bore complete all as specified and directed.

S & F gun metal gate valve for 15mm bore pipe with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Notes :- (a) The contract sum shall be arrived at after deduction of amount of Schedule of Credit. (Rs. 16,188.00). (b) PERFORMANCE SECURITY :- (Refer condition 19 of IAFW-2249) The performance security for an amount equivalent to 5% (Five percent) of the accepted contract sum shall be delivered by the successful bidder immediately after the date of intimation letter of acceptance and all provisions shall be applicable as per condition 19 of IAFW 2249.

kay gee construction co

Ambika Construction Co

JANDIAL ENTERPRISES

VIKRAM SINGH MANHAS

Pathania Builders

M/s. G M Builders & Contractors

kamal electric works