REPAIR MAINTANANCE TO CERTAIN ROADS INCLUDING ROAD FURNITURE IN GRC AREA-I UNDER GE KAMPTEE

Amount

Repair to pot holes any depth, n. exc. 1 sqm each including sweeping with mechanical equipment and making the surface free from dust and mud or water, scoring sunken surfaces in roads, paths, etc. by using pressure air, cutting around edges to atleast 25 mm in depth making good by applying tack coat at 5 kg per 10 Sqm, putting in premixed bituminous macadam, well rammed and sealed with binder 9.8 kg per 10 Sqm, blinded with 0.09 cum of stone chippings of 6.3 mm size and again well rammed (including supply of premixed macadam, binder and chippings), depth of pot holes exc. 30 mm using paving bitumen, complete all as specified and as directed.

Material and labour for scarifying or picking gravelled, macadam or bituminous macadam surfaces in area n.exc 400 sqm and n. exc 50 mm deep and removal from site , complete all as specified and directed.

Material and labour for preparing black top surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surface with mechanical equipment, to remove all loose dirt etc. complete and applying evenly a priming/tack coat with bituminous primer over black top surface at 5 kg per 10 sqm using paving bitumen grade VG-10 on blacktop surface using mechanical sprayer and providing premix asphaltic semi-dense concrete 30mm consolidated thickness with 5.5% binder content (paving bitumen any penetration of grade VG-30) by weight of total mix and 2 % cement filler, rolled and compacted to required camber and gradient , using 8 to 10 tonne power roller complete all as specified ans directed. Note: The work shall be executed by using hot mix plant & mechanical paver. The rate quoted shall be deemed included for cement filler.

Material and labour for applying evenly a priming/tack coat with bituminous primer at 10 kg per 10 Sqm using paving bitumen grade VG-10 on unsurfaced WBM using mechanical sprayer complete all as specified and directed.

Material and labour for premixed bituminous macadam (consolidated thickness 75mm or less) using with 4% binder content (paving bitumen any penetration of Grade VG-30) by weight of total mix and rolled and compacted to required gradient and camber using 8 to 12 tonne power roller complete all as specified and as directed.

Material and labour preparation of road surface and applying thermoplastic reflective paint in marking minimum 2.5mm thick single coat as in centre line and edge line road marking of 150/100 mm width using HOT MARK thermoplastic modern propelled road marking machine as directd including all ingredients such as blinder, glass beads Titanium dioxide calcium corbonate inter filler thermoplastic requirement for glass beads shall be the table No 800.4 of MOT specification including spraying of glass beads etc. complete all as per manufacture instruction and as directed.

Spreading moorum/red bajri, in road berms 100mm spread thickness for light waring surface with moorum/bajri , spread, rolled and consolidated to gradient and camber required with light roller of capacity not less than 0.5 tonne, complete all as specified and directed.

Supply and fix 1000mm dia convex mirror made of PC material provided with suitable MS pipe post,duly powder coated for road turning, intersections, curves, T- junctions, parking lots etc. and also held ideal for surviliance , it should have clear definite mirror image having 130 degree of viewing angle. It is unbreakable and stronger than glass complete all as specified and as directed. Make:- GREENS/GREENLITE/3M and DARK EYE.

Supply and fix solar road stud having 3 LEDs of colours unbreakable poly carbonate shell & clear facings designated for maintenance free operation 100 % water proof design confirms to IP67, Dimension 125 x 125 x 25 mm with dual shank of 65 mm High efficiency mono- crystalline solar panel 3 V/ 120 mA, One Ni Mh LSD rechargeable battery (1.2 V / 800 mA) high temperature, Six super bright LEDs with 14,000 mcd, view distance upto 1000m, Flash rate 2 Hz or according to customers requirements, bearable weight 20 Tons, Colour: Red, Amber, Blue, Green and white, Working time 30 to 40 hours successively after the battery is fully charged. The electronic circuit is encapsulated with the battery in the body of solar stud, a non-invasive switch (optional) to avoid battery drainage during storage and transportation, Charging time: five to six hours/day, Working temperature: 40ᵒC - 75ᵒC, Lifetime: Three to five years, Easy installation, no maintenance, brightness sensitive auto-switch automatically turns on at night and turns off at dawn, high visibility LES's help ensure easy and safe night driving, ideal for highways, parking lots, roads and similar isolated or stand-alone traffice applications, Model No. DA 113, complete as per MORTH/ IRC specifications and manufacturers instruction, complete all as specified and directed.

Supply and fix aluminium road studs of size 110 x 128 x 30 mm with shank reflective , micro prismatic (red/ amber/ white) with MS zink coated nails of size 12 mm dia and 120 mm long having both as sides (Dual direction) high impact ABC 3 Nos containing 7 heads each i.e. 42 heads in retro-reflector etc. complete all as specified and directed. Model No. DA-972- Dark eye or equivalent as approved by GE.

vidhamal&sons

M/s SHREE SAIBABA CONSTRUCTION

Bidder Name

vidhamal&sons

M/s SHREE SAIBABA CONSTRUCTION

M/s KAMAL R AGRAWAL