Construction of 1 No of C-Type Qtrs for Civil Judge (Senior Division ) at Khandapada.

Earth Work in exavation of foundation in hard soil within initial leads of 50m & lifts of 1.5m including dressing and levelling of bed etc. and adding contractor's profit and over head charges, etc. complete in all respect for the work as directed by the Engineer-in-charge.

Supplying & Filling foundation trenches , plinth & ditches with clean coarse river sand well watered and rammed in layers not exceeding 23 c.m. in depth with all lead and lift including cost, conveyance, loading, unloading, stacking, royalties and all cost & conveyance of water, cost of all Labour,labour ess,T&P required for the work etc. complete in all respect as directed by the Engineer- in -charge.

Providing and laying plain cement concrete of proportion (1:3:6) in foundation and floors using 4 cm. size hard crusher broken granite stone aggregate and screened and washed sharp sand for mortar of approved quality and from approved quarry including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm. thick in each layer including all cost, conveyance, royalties and cost of all labours,labour cess, T&P etc complete as per specification & direction of the Engineer-in-charge.

Providing lifting hoisting and laying Reinforced cement concrete of M 20 using 12 mm to 20 mm. (½ to ¾) size (20 mm not to exceed 25) hard crusher broken granite stone aggregate of approved quality from approved quarry including hoisting lowering laying and compacting concrete watering curing centering shuttering and finishing the exposed surfaces smooth with all cost conveyance royalties taxes of all materials with all labour,labour cess and T and P required for the work etc. complete in all respect but excluding the cost and conveyance of MS rods or Tor steel and binding wire of 18 to 20 gauge and labour charges for straightening cutting bending binding and tying the grills and placing in proper position and as per the direction of the Engineer in charge.

Column Super Structure Ground Floor

First Floor

Plinth Band

Lintel Band Ground Floor

First Floor

Roof Beam Ground Floor

First Floor

Chajja & Shelves Ground Floor

Stair case & Step Ground Floor

Roof Slab Ground Floor

First Floor

Supplying Cutting, straightening coiled or bent up M.S. Rod or tor steel of primary steel producers such as SAIL / TATA / RINL / JINDAL STEEL / SHYAM STEEL (grade Fe-500D) etc. including bending, binding, welding and jointing if necessary and tying the grills and placing in position as required for R.C.C. Work and for providing fan hooks as required, hoisting, lowering, laying including all cost, conveyances of M.S. Rod or tor steel and binding wires of 18 to 20 gauge and labour required for the work for bending, binding and tying the grills in all floors with labour cess etc. (payment will be made on standard weight of B.I.S. for M.S. Rods or tor steel only) etc. complete as per specification & direction of the Engineer-in-charge.

First Floor

Fly Ash brick masonry in cement mortar (1:6) in Foundation and plinth using Fly Ash bricks of 25 x 12 x 8 cm size having a crushing strength of not less than 75 kg./sqcm with dimensional tolerance ± 2% including splays cutting circular moulding chamfering and corbelling and similar such type of works with all necessary projections watering and curing after immersing the bricks in water at least for six hours before use including all cost, conveyance, royalties with all labour,labour cess and T & P required for the work complete in all respect as per specification and direction of tne Engineer-in-Charge.

Fly Ash brick masonry in cement mortar (1:6) in Super structure using Fly Ash bricks of 25 x 12 x 8 cm size having a crushing strength of not less than 75 kg./sqcm with dimensional tolerance ± 2% including splays cutting circular moulding chamfering and corbelling and similar such type of works with all necessary projections watering and curing after immersing the bricks in water at least for six hours before use including all cost, conveyance, royalties with all labour,labour cess and T & P required for the work complete in all respect as per specification and direction of tne Engineer-in-Charge.

First Floor

Terrace

Providing 12mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with all cost, conveyance, royalties, with cost of all labour,labour cess, T&P, and scaffolding required for the work etc. complete in all respect and specification and direction of the Engineer in charge.

First Floor

Terrace Floor

Providing 16 mm thick cement plaster with cement mortar of mix (1:6) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with all cost, conveyance, royalties, with cost of all labour,labour cess, T&P and scaffolding required for the work etc. complete in all respect as per direction of the Engineer-in-charge .

First Floor

Providing 6 mm thick cement plaster with cement mortar of mix (1:4) with screened and washed sharp sand for mortar and finished smooth to the rough surface of walls in all heights after racking out joints including watering and curing, rounding of corners, providing grooves where ever necessary with all cost, conveyance, royalties, with cost of all labour,labour cess, T&P and scaffolding required for the work etc. complete in all respect as per direction of the Engineer-in-charge .

First Floor

Supplying, fitting & fixing of Vitrified colour printed series tiles of thickness 8mm to 10mm in floors of size 600mm x 600mm of approved make confirming to IS:13755 laid on 20 mm thick cement mortar (1:4 ) (1 cement : 4 course sand) and filling joints with white cement of approved quality including cost of all materials, labour, labour cess, T&P etc. required for the work all complete as per direction of the Engineer-in-charge

First Floor

Supplying, fitting & fixing of Vitrified Tiles in Dado colour printed series tiles of thickness 8mm to 10mm in dadoes, skirting and risers of steps of size 600mmx 600mm of approved make confirming to IS:13755 laid on 12 mm thick cement mortar (1:3 ) (1 cement : 3 course sand) jointed with slurry mixed with pigment to match the shades of the tiles including rubbing and polishing etc. complete including cost of all materials, labour , labour cess, T&P etc. required for the work all complete as per the direction of the Engineer-in-charge

First Floor

Supplying, fitting & fixing of Granite Tiles of minimum 20mm thick and size above 0.40 sqm of approved make in floors over 20mm thick bed of cement mortar 1:4 jointed with cement slurry mixed with pigments to match the shade of the tiles, including rubbing & polishing etc. complete including cost, conveyance, taxes & royalties of all materials, labour with T&P complete in all respect and as per direction of the Engineer-in-charge

Finishing surface of walls with cement based wall putty (water based) of approved make and finished smooth and even surface to receive painting including sand papering, cost of scaffolding, staging charges with cost, conveyance, taxes of all materials, cost of all labour, T&P etc. complete as per the direction of the Engineer-in-charge

First Floor

Priming one coat with any approved primmer including cost of primmer & labour to give an even shade with cost,conveyance & taxes of all materials & labour with T&P required for the work etc. complete in all respect as per specification & direction of the Engineer-in-charge.

First Floor Outside

First Floor Inside

Terrace

Painting two coats with approved quality of Plastic Paint over the interior surface of the walls with one coat of wall Primer including all labour charges cost, conveyance & taxes of all materials,labour,T&P required for the work etc. cmplete in all respect as per specification and direction ofthe Engineer-in-Charge.

First Floor

Painting two coats with any approved colour of weather seal coat to out side surface of wall of approved shade and quality etc including sand papering, polishing the surface, all cost, conveyances of all materials and cost of all labour, labour cess with T&P etc, complete as per specification & direction of the Engineer-in-charge.

First Floor

Terrace

Supplying of MS Grills/shutter of approved quality and design to windows and openings and staircase railing and parapet railings etc including making holes in walls and RCC structures or wood work etc in proper position making good the damages of walls or RCC or other structures complete including bending or cutting sizes or grooves in chowkhats with all cost and conveyance of all materials labour , labour cess with T&P required for the work and royalities etc.complete (including screws) in all respect in all floors as per the direction of Engineer-in-Charge .

Grill

First Floor Door

Grill

Supplying, fitting and fixing hand railing of Stainless steel of 304 grade using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm x 2mm @ 0.90mtr. C/C and stainless square pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as per approved design and specification, buffing, polishing etc with all cost, conveyance, taxes of all materials, cost of all labour, T&P etc. required for the complete in all respect as per direction of the Engineer-in-charge.

First Floor

M.S Truss made out of Square Hollow Section of different sizes of grade YST-310.as per approved design and specification, buffing, polishing etc with all cost, conveyance, taxes of all materials, cost of all labour, T&P etc. required for the complete in all respect as per direction of the Engineer-in-charge.

Ground Floor

First Floor

First Ground Floor

First Floor

Priming One Coat with approved Primer of approved colour, shade to Doors, Windows shutter & Grills including sand papering, polishing the surface, cost, conveyances of all materials and cost of all labour etc, complete as per specification & direction of E.I.C.

First floor

Painting two coats of enamel over a coat of priming paint to new M.S. iron work including cost primer,sand papering,polishing the surface with cost,conveyance & taxes of all materials & labour with T&P required for the work etc. complete in all respect as per specification & direction of the Engineer-in-charge.

First floor

Providing and laying grading conc. 25 mm (avg. thickness) cement concrete of required slope of mix 1:2:2 (1cement:2sand:2 graded stone aggregate of 10 mm nominal size) mixed with approved water proof compound as per manufacturer's specification on top of slab including cement slurry, all complete, including the cost of water proofing admixture, which should be approved by the Engineer-In-Charge prior to material procurement by the contractor.

First floor

Providing fitting and fixing of false ceilling with Aluminium anodised T Section No. 3215 with 2'-0" center to center, L section No. 1705 upto 15 micron on 4 walls to be fixed by means of steel screw and P.V.C plug and the Aluminium grid 2'-0"x2'-0" suspended from ceiling etc complete Data for 14'-6" x 14'-6" = 210.25Sft or 19.53 Sqm

First floor

EI WORKS Recessed wiring to Group -B light /Call bell point with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked in 20 mm dia flexible non-mettalic conduit with 6Amp, 250V Modular switch ISI marked and ceiling rose ISI marked mounted on metal box having front Modular cover of suitable size, metal box with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accessories and connection. (Make of wire-L&T/ Anchor/ Havells/ V-Guard/ RR KABEL) )

Recessed wiring to Group -C light /Call bell point with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked in 20 mm dia flexible non-mettalic conduit with 6Amp, 250V Modular switch ISI marked and ceiling rose ISI marked mounted on metal box having front Modular cover of suitable size, metal box with 1.5 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire including all accessories and connection. (Make of wire-L&T/ Anchor/ Havells/ V-Guard/ RR KABEL) )

Recessed wiring to submain in 2 x 1.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISImarked confirming to IS-694/1990 in 20 mm dia flexible non-mettalic PVC conduit 1.6 mm thick alongwith 1 x 1.5 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire as equired.(Makeof wire Finolex/L&T/Anchor/Havels/V Guard)

Recessed wiring to submain in 2 x 2.5 sq.mm FR PVC insulated single core multistrand copper conductor of ISImarked confirming to IS-694/1990 in 20 mm dia flexible non-mettalic PVC conduit 1.6 mm thick alongwith 1 x 1.5 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire as equired.(Makeof wire Finolex/L&T/Anchor/Havels/V Guard)

Recessed wiring to submain in 2 x 4 sq.mm FR PVC insulated single core multistrand copper conductor of ISImarked confirming to IS-694/1990 in 20 mm dia flexible non-mettalic conduit 1.6 mm thick alongwith 1 x 1.5 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire as equired.(Makeof wire Finolex/L&T/Anchor/Havels/V Guard)

Recessed wiring to submain in 4 x 6 sq.mm FR PVC insulated single core multistrand copper conductor of ISImarked confirming to IS-694/1990 in 32 mm diaflexible non-mettalicconduit 1.6 mm thick alongwith 2 x 4 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire as equired.(Makeof wire Finolex/L&T/Anchor/Havels/V Guard)

Recessed wiring to submain in 4 x 10 sq.mm FR PVC insulated single core multistrand copper conductor of ISI marked confirming to IS-694/1990 in 40 mm dia non-metalic heavy duty PVC conduit 1.6 mm thick along with 2 x 4 sq.mm FR PVC insulated single core multistrand copper conductor as earth wire as equired. (Make of wire- Finolex/Anchor/Polycab/ HAVELLS/RR KABEL or equivalent) (Make of conduit-AKG/Anchor/Kinjal or equievalant)

Supply and drawing of TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated shielded with fine tined copper braid & protected with FR PVC sheath in existing surface / recessed STEEL / PVC conduit as required.

Recessed wiring for 2 x 6 amp socket outlet controlled by 2 nos 6Amp, 250 V clip in type switch ISI marked mounted on single G.I moular box with face plate & cover of suitable size including all accesories and connection on separate board as per direction of Engineer in Charge.

Supply and fixing of 6Amp plug with 6Amp switch on existing board (Modular type)

Supplying,fixing of 1x16A Plug on the separate board with complete fitting by 01 no of 16A switch & socket(modular type)( flame retradant type)) with suitable size modular box & cover( falme retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg- in-charge..

Supplying,fixing of TV socket(modular type)( flame retradant type)) with suitable size modular box & cover( falme retradant type) including supplying of all required accessories of ISI marked as approved as per direction of engg- in-charge..

Supplying,fixing of 3x6A Plug on the separate board with complete fitting by 01 no of 16A+3 nos 6A switch & socket(modular type) (anti bactorial & flame retradant type) with suitable size modular box & metallic cover plate ncluding supplying of all required accessories of ISI marked as approved as per direction of engg-in-charge(Make- Legrand / Roma/ Havells)

Recessed wiring for A.C/ Power socket outlet with industrial type socket outlet, plug top and metal chained cover in sheet steel enclosure ,20A/32A SP MCB including all accesories and connection as per direction of Engineer-in-charge.

Supply, Installation, Testing and Commissioning of ceiling fan 1200mm sweep,BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated single core multiatrand copper conductor etc. as required.

S/F of 16" wall mounted fan complete with all connection (Usha/Havells/Bajaj)

Supplying, installation, of exhaust fan of 300 mm sweep 1400 rpm with louvers (MakeHavells/almonard/cromptron/Halonix/bajaj make or any other equivalent reputed make star rated as approved) of exhaust fan in the existing wall, including fixing & conntection .as required as per direction of Engg.-in-Charge

Supply and fixing CALL bell (Ding dong type) /Buzzer on the existing switch box/cover of Anchor make .as required as per direction of Engg.-in-Charge

S/F of 20watt LED tube light with all connection(Havells/Crompton/Bajaj)

SITC of Sleek LED 25 watt surface/recess square type fitting with extruded polycarbonate housing,High optically efficient diffuser, complete with all accessoriesetc. directly on wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. ( Make :Make: PHILIPS/BajajHavells/Crompton make)

SITC of Indoor type wall concealed foot light with LED Similar to Legrand Myrius CAT NO. 673036 with metal box complete as required or equivalent.

Providing & fixing of LED type 5w Mirror Light including making connections using copper lugs etc. complete as required.

Supply and Fixing of Surface mounted indoor / Outdooe type 10W BULK HEAD LED Luminaire with LED Lamp Similar to WIPRO Cat No. LW07-141-XXX-57-G1 / JAQUAR / Philips / Halonix / Panasonic or equivalent.

Supply and fixing of following TPNDB MCB distribution board 250V on surface/recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (but with out MCB/ RCCB/ Isolator) (make-Legrand Ekinox3 ETPN/Scnider Acti 9./Eq Make)4way

Supply and fixing of 5Amp to 32A rating 240 V/415 V "C" series MCB suitable for lighting and other loads of the following poles in the exiting MCB DB ISI marked complete with connections testing and commissioning etc. (Make-Legrand DX3/Scnider Acti 9/L&T)63A FP MCB C Series

5-32A SP MCB C Series

Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc (But wih out charcoal and salt) as required.

Supplying and laying 25 mm x 5 mm copper strip on surface or in recess for connection etc as required.

Supply, installation of 2.5 KVA/36V inverter of Luminous Make with 2 Nos of 200 AH Battery Cruze+ 3.5 KVA-36V

SITC of MAIN PANEL with 125 A 4P MCCB 25 KA -1 No as incomer,4 Nos 63A FP MCB 10KA, 2 Nos 32 DP MCB and Surge Protection Device with E.C Busbars .

Supply of 25sqmm 31/2core Allm. armoured XLPE insulated cables ISI marked.(Make- Gloster/ Polycab/ Havells/KEI or eq. model)

Laying of one number of PVC insulated and PVC sheathed / XLPE power cable of 1.1KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation, sand cushing, protective covering and refilling the trench etc. as required.

Supply and making end termination with brass compression gland and aluminium logs for 4 X 16sqmm size of PVC insulated and PVC sheathed / XLPE aluminium cable of 1.1kv grade (without cost of cable ) as required.3 1/2 x 25sqmm

Supply and laying of Double WALL CORRUGATED (DWC) HDPE of size 63/51mm including transportation

Supply and installation of Rubber Mats 12mm thick of size 2000mm x 1000mm x 12 mm thick Electrical tested with test certificate.

Supply and fixing of fire buckets with angular fabricated stand to fix 4 buckets in each stand for Electrical fire protection as per standards of Electrical Inspectorate.

Supply and fixing of Co2 fire extinguisher with mounting clamps with pressure test certificate .

Supply and fixing of shock treatement charts duly laminated along with separate colour single line diagram laminated, to be fixed in Electrical control panel room.

Supply and fixing of first aid box with medicines complete with medicine with three years expiry date to be fixed in Electrical control panel room.

Supply and fixing of A,C with indoor and outdoor unit 1.5 TR high wall 5 star non-inverter type split A.C machine (BTU/Hr-18000)with copper condensor & evaporator having ambient temperature 52 degree celcius with comprehensive 1 year warranty,5 years warranty on PCB, 5 years warranty on compressor (Make:As approved by PWD or Govt of Odisha.)

Supply of 4 KVA Voltage stabilizer with all accessories as required as per the direction of Engineer-in-charge. (Make-V-Guard/Microtek or Eqv.)

REFRIGRANT PIPING - Supply,installation of hard/soft copper refrigerant piping of size 5/8 inch and 1/4 inch for suction and liquid line with 3 corex4 sqmm FRLS Copper control cable alongwith 25mm weather proof closed cell nitrile insulation ,complete with fitting of bends and other nesessary material to complete the job. Make of cabel-RR Kabel/KEI/Finolex/Polycab/Gloster or Eqv) incl Drain Pipe

Supply of Elegant look 60 W AIO LED Solar Street lights having extruded alluminium housing 150Wp or more highly efficient Mono Crystalline Panel/Laminates fixed on the top of the luminaire housing maintenance free 12 8 volts 54 Ah or more LiFePO4 battery BIS certified BMS MPPT charge controller PIR sensor to provide 2 days 48 hrs back up . The luminaire is having IP 66 protection for critical components IK 07 and having lumen output of 9000 lumen as LM 79 Lenses should be provided on the LED chip for better lighting dstribution to avoid glare on human eyes Both the luminaire and Mono Crystalline Panel must be manufactured in India. warranty certificate on their companys letterhead by mentioning minimum warranty period as 5 years Make As approved by Govt of Odisha or PWD

Supply of 6 mtr long HOT DIP galvanised Octagonal pole having 3.0mm thick, 70mm of top and 135mm bottom with base plate of (220x220x12 ) mm thick and foundation bolt with Anchor plate complete with nut bolt and with sowrd type single decorative arm as per the direction of engineer in charge ( MAKE-BAJAJ/UTKARSH/VALMONT/Equi)

Providing and Construction of Electrical Foundation using RCC strcuture M-25 Grade (1:1.5:3) with PCC bed on sand fillling and required excavation, labour, transportaion towards approach road side ,suitable adapator with G.I clamping arrengement and anchor fistner on the bridge with the barricate etc. complete as per directions of Engineer-in-charge

Supply and fixing Earthing with G.I earth pipe 3mtr. Long 40mm dia ISI marked including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required Standard earthing as per Govt. spcn.

S/F of 25 X5 mm GI flat

S/F. of 75Wt. LED Street light fittings complete with G.I. bracket. Of Philips/Crompton/Bajaj category ISI marked as per direction Engineer-In-charge

Supply and fixing of 15 Ltr. Geyser category ISI marked as per direction Engineer-In-charge(Make : As approved by Govt of Odisha)

LA Supply , Installation, Testing & commissioning of 3 mtr vertical air terminal with mounting accessories on the flat surface to meet the requirements of IS/IEC 62305. Tested for Electrical , mechanical and chemical as per IEC 62561. Tested for 100kA lightning current. (Make:OBO/Stromking/ Satalite-3/Indilac)

Providing and fixing of G.I. tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)

Providing and fixing of G.I. tape 20 mm x 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)

Reveting, sweating and soldering of copper / G.I. tape ( with another copper / G.I. tape, base of the finial or any other metallic object) as required.

Supply , Installation, Testing & commissioning of Roof conductor holder for parapet- Polyamide Conductor holder: With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder. Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance. Tested as per IEC 62561. (Make:OBO/Stromking/ Satalite-3/Indilac)

SS Screw M10 x 50 mm with PVC wall Plug

PVC Sleeve

Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc (But wih out charcoal and salt) as required.

Supplying and laying 25 mm x 5 mm copper strip on surface or in recess for connection etc as required.

MV Inspection and 3phase Service Connection

PH WORKS Supplying all materials, labour, T&P and providing and fixing to wall or ceiling and floor pvc pipes conforming to ASTM-D-1785/89 (Sch-80) and pipe fittings of the following nominal bore with clamps including making good the wall, ceiling and floor all complete as per specification and direction of the Engineer in charge(Supreme/Ashirvad/Oriplast).

25mm Dia CPVC pipe

25 mm Dia ASTM (Sch-80) Pipe

32 mm Dia ASTM (Sch-80) Pipe

first floor 20mm Dia CPVC Pipe

25mm Dia CPVC pipe

25 mm Dia ASTM (Sch-80) Pipe

32 mm Dia ASTM (Sch-80) Pipe

2nd floor 32 mm Dia ASTM (Sch-80) Pipe

40 mm Dia ASTM (Sch-80) Pipe

supplying all materials, labour, T&P and cutting holes through existing brick work including making good the damages in cement mortar (1:4) for taking G.I. Pipes and fittings/ P.V.C. pipes and fittings etc. all complete as per P.H. specification and direction of E.I.C.

250 mm thick wall in FF

Supplying all materials, labour, T&P and cutting hole in R.C.C floors, roofs, etc upto 19 cm thick for passing GI pipes / PVC pipes and fittings etc and repairing the holes after insertion of pipes etc with cement concrete (1:2:4) including finishing complete so as to make it leak proof as per direction of the Engineer in charge.

in first Floor

Supplying all materials, labour, T&P and cutting grooves in pucca floors and walls for taking GI/ PVC pipes and making good the damages as per the direction of the Engineer in charge.

in first Floor

Supplying all materials, labour, T&P and fitting and fixing brass/CP fittings of the following nominal bore with supply of all jointing materials complete as per specification and direction of the Engineer in charge 15mm dia CP Bib cock (FLR-CHR-5047N Jaquar make)

15mm dia long body Bib Cock cock (Jaquar)-CON-CHR-107KN

15mm dia CP Sink Cock (FLR- CHR- 5347 NJaquar make)

20mm dia CP concealed stop cock(Jaquar)CON-CHR-087KN

15mm dia. C.P angle stop cock (Jaquar)-CON- CHR-053KN

15mm dia CP Pillar cock (Jaquar)CON-CHR- 021KN

15mm dia CP Health faucet.ALD-CHR-579

15mm dia Two way Bib Cock (Jaquar)-CON- CHR-041KN

15mm CP revolving shower with 15mm x 225mm long CP shower arm

25mm dia brass or gun metal full way valve(shakti make)

32mm dia brass or gun metal full way valve(shakti make)

40mm dia brass or gun metal full way valve(shakti make)

15mm dia CP Flange

15mm dia CP Extention Nipple

125mm CP grating

Supplying all materials,labour,T&P and fixing Rotational moulded polyethylene cylindrical vertical water storage tanks conforming to IS : 12701--1996 including cutting holes through the tank and fixing mild steel tubes and fittings and providing extra sockets and jam nuts, fixing ball valve etc, including hoisting upto a height of 5 metres above ground level and placing the tank to the required position and providing 1st class Fly ash brickwork in cement mortar (1:6) of 0.46m height in staging and in circular protection wall to support the tank, 12mm thick cement plaster (1:6) over brickwork, R.C.C slab of size 1.60mx1.60m and 0.10m thick, R.C.C beam of 0.25mx0.30m and 2.60m average length in cement concrete(1:2:4) using 12mm size h.g chips including centering and shuttering, watering, curing, conveyance of all materials to worksite etc all complete as per specification and direction of the Engineer in charge. Fixing 2000 Ltr Roto-moulded water storage tank (Syntax Make) on the roof of 2nd floor.

Supplying all materials labour Tand P and fitting and fixing U PVC SWR soil waste ventilating pipes and fittings of the following outside diameter conforming to ISI No. 13592/1992 to walls with nails bobbins and wooden plugs or laying in trenches including jointing with supply of approved rubber lubricant by non heat application method/as per manufacturers specification testing earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the Engineer in charge (Supreme/Ashirvad/Oriplast).

50mm dia U-PVCClass-IV pipes

110mm U-PVC door tee

110mm U-PVC Plain tee

110mm U-PVC door bend

110mm U-PVC plain bend

110mm dia U-PVC 'P' trap

110mm dia U-PVC Plain Shoe Bend

110mm dia U-PVC offset with out ear

110mm dia U-PVC cowl

110mm dia U-PVC Clamp

75mm dia U-PVC Door Bend.

75mm dia U-PVC Plain Bend.

110x75mm dia Reducer

Supplying all materials, labour, T&P and cutting holes through existing brick or laterite masonry wall for taking HCI pipes and fittings including making good the damages etc all complete as per PH specification and direction of the Engineer in charge. 250mm to 375mm thick wall

Supplying all materials, labour, T&P and cutting of R.C.C roof or cornice for taking H.C.I pipes and making good the damages etc all complete as per P.H.Specification and direction of the Engineer in charge.

Supplying all materials labour TandP and fixing the following vitreous china Wash Down Water Closet European type WC pan with integral Por S trap to the floor with wooden plug and chromium plated pedestal screws including jointing the trap with soil pipe in cement mortar (1:1) fixing plastic seat and cover for wash down water closet with chromium plated brass hinges and rubber buffers including polishing etc all complete as per specification and direction of the Engineer in charge. Orrisa pan (Parryware/Hindware/Somany/Cera/Kerovit)

Supplying all materials labour TandP and fixing the following vitreous china Wash Down Water Closet European type WC pan with integral Por S trap to the floor with wooden plug and chromium plated pedestal screws including jointing the trap with soil pipe in cement mortar (1:1) fixing plastic seat and cover for wash down water closet with chromium plated brass hinges and rubber buffers including polishing etc all complete as per specification and direction of the Engineer in charge.

Supplying all materials, labour, T&P and fitting and fixing 10 litres capacity low level flushing cistern with a pair of cast iron or M.S brackets complete with fittings such as siphonic arrangements 15mm nominal size brass/pvc ball valve with polythene float CP brass handle, unions and couplings for connection with inlet, outlet and overflow pipes,32mm dia CP flush bend,15mm dia pvc inlet connection pipe including cutting holes and making good the same and connecting the flush bend with cistern and closet and connecting the inlet pipe with supply main etc all complete as per specification and direction of the Engineer in charge 10 litres capacity pvc low level cistern with 32mm dia CP long flush bend Slimline white (Parryware/Hindware/Somany/Cera/Kerovit)

Supplying all materials labour Tand P and fixing wash basins with hole for pillar taps with cast iron or M S brackets painted white including cutting holes in walls and making good the damages with supply of wooden plugs screws and cement etc fixing pedestal for wash basin recessed at the back for the reception of pipes and fittings, fixing PVC waste pipe of 32mm nominal diameter for wash basin including brass check nut complete fixing pillar taps capstan head screw down high pressure lettered Hot and Cold with long screws shanks and back nuts of 15mm dia nominal bore fixing 15mm dia PVC inlet connection pipe and making connection with pillar cocks and supply mains for wash basin fixing 32mm dia CP brass waste etc all complete as per specification and direction of the Engineer in charge. 550mmx440 mm size wash hand basin With porcelain pedestal (Parryware make)

Supply all materials and labour for fitting and fixing of following size white glazed vitreous chinaHalf Padestal wash hand basin of approved make in all floor of approved quality including cutting the walls & floor and making good the damages with cement concrete (1:2:4) etc. including all taxes, duties, transportation etc. all complete as per direction of EIC. (Make:JAQUAR/HINDWARE/CERA/PARRYWARE) Half pedestal basin FNS-WHT-40801 Wall Hung Basin with Fixing Accessories Size: 620x480x185 mm & FNS-WHT-40305Half pedestal with Fixing Accessoriesfor 40801

Supplying all materials, labour, T&P and fixing wash kitchen sink/laboratory sink With sink cock with cast iron or M S brackets painted white including cutting holes in walls and making good the damages etc all complete as per specification and direction of the Engineer in charge 600x450x250 mm SS sink

Supplying all materials,labour, T&P and fixing standard sized CP towel rail complete with CP brass brackets fixed to wooden plugs with CP screws as per specification and direction of the Engineer in charge 25mmx600mm long CP towel rail

CP Towel ring

Supplying all materials ,labour ,T&P and fixing CP Soap Holder complete with CP brass brackets fixed to wooden plugs with chromium plated brass screws etc.all complete as per specification and direction of Engineer-in-charge. CP soap holder

Supplying all materials, labour, T&P and fixing standard sized glass-shelf with CP brass brackets and guard rails complete fixed to woden plugs with CP screws as per specification and direction of the Engineer in charge.600mmx125mm glass shelf with CP/NP guard rails

Supplying all materials, labour, T&P and fixing mirror of superior glass mounted minimum 5m thick on 6mm thick A.C sheet or plywood sheet and fixed to wooden plugs with CP screws and washers complete as per specification and direction of the Engineer in charge. Mirror(Bevellededge) 600mmx450mm.

Design Mirror

Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12mm size hard broken granite chips including watering, curing, conveyance of all materials to worksite, payment of royality, taxes etc all complete as aper specification and direction of the E.I.C.

First floor

Supplying all materials, labour, T&P and providing ceramic tiles in floors, treads and landing on 25mm thick bed of cement mortar 1:1 (1 cement:1 sand) joined with neat cement slurry mixed with pigment to match the shades of the tiles including rubbing and polishing complete as per direction of the Engineer in charge. size 30 x 30 cm Kajaria / equvalent to be pree approved . ground floor

First floor

Supplying all materials, labour, T&P and providing 12mm thick cement plaster (1:4) on brickwork including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge Ground floor .

First floor

Supplying all materials, labour, T&P and fixing porcelain glazed tiles in dados skirting on 12mm thick cement plaster (1:3) jointed with neat cement slurry mixed with pigments to match the shades of the tiles including rubbing and polishing complete as per direction of the Engineer in chargeKajaria / Somany of size 30 cm x 45 cm size in Ground floor

First floor

Factory made single leaf rigid FRP(alternately called GRP) sandwich composite door shutter of 32mm thick laminated with two GRP skins with wood grain finish fabricated using UV-stabilised Isopthalic Gelcoat and one layer of 450 gsm E-glass Chopped Strand Mat (CSM) impregnated with orthopthalic palyester resin. The thickness of the skins shall not be less than 3.00mm Expanded Polystyrone(EPS) structural foam panel of 29mm thickness and a density of 20kg/cu.mtr shall be used as core material. Wooden reinforcements made of seasoned sal wood block of cross section not less than 28mmx32mm and also necessary sal wood reinforcements for fitting the metal fittings such as tower bolts, aldrops, handles etc shall be provided. A structural adhesive compatible with (EPS) foam shall be used for bending the core material, the sal wood reiforcements and the skins. The material and process for manufacturing the door shutters shall conform to RV-TIFAC composites Design Centre's standards and specifications and the door shutters tested in conformation to IS: 4020-1998. The finish of door shutter will be plain colour white/ Ivory/ Beige/ Light grey/ Mahogany/ Teak wood or any other colour using high quality pigments. Three heavy whight mild steel butt hinges type-I(ISI marked) size 100mm are to be fitted on one side of shutter with FRP frame of size 45x90mm. (Darwaja /Exon Door make)5x0.75x2.10=

Supplying all materials, labour, T&P and constructing gully trap chamber of the following inside size with 8cm thick R.C.C precast cover slab in cement concrete (1:2:4) mix using 12mm size h.g chips, foundation concrete (1:4:8) using 40mm size hard granite metal on bed and around trap, KB brickwork in cement mortar (1:6) in F&P and inside 12mm thick cement plastering (1:3) finished with a floating coat of neat cement including fixing 100mmx100mm size HCI gully trap,150mmx150mm size CI grating etc all complete as per approved drawing, specification and direction of the Engineer in charge. Inside size 250mmx250mm

Supplying all materials, labour, T&P and constructing inspection chamber of the following size with cement concrete(1:3:6) using 40mm size hard granite metal on bed, 1st class fly ash brickwork in cement mortar(1:6), moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size h.g chips, 12mmthick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, RCC cover slab in (1:1.5:3) using 12mm size h.g chips with RCPC man hole cover, earthwork in excavation in all kinds of soil and refilling the cavity around the chamber including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge. Inside size 760mmx760mmx460mm

Supplying all materials, labour, T&P and constructing man hole chamber of the following size with cement concrete(1:3:6) using 40mm size hard granite metal on bed, fly ash brickwork in cement mortar(1:6), moulding and shaping the channel inside and benching with cement concrete (1:2:4) using 12mm size h.g chips,12mmthick cement plaster (1:3) with punning to inside, cement flush pointing (1:3) to outside, R.C.C cover slab in (1:1.5:3) using 12mm size h.g chips with RCPC man hole cover, earthwork in excavation in all kinds of soil and refilling the cavity around the chamber including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge. Inside size 910mmx910mmx910mm

Cost of R.C.P.C.Cover.

Supplying all materials, labour, T&P and constructing soakway pit of the following size with dry brick walling from bottom upto invert of inlet pipe and 1st class K.B brickwork in cement mortar (1:6) for the remaining height at top, cement concrete (1:4:8) using 40mm size hg chips on bed, 12mm thick cement plaster (1:4) inside and outside over masonry brickwork, gravel backing in the rear of well steining, RCC cover slab in cement concrete (1:2:4) using 12mm size hg chips fitted with iron lifting handles including earthwork in open well excavation in all kinds of soil and refilling of cavity around the pit & painting the iron works, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per approved specification and direction of the Engineer in charge Brick masonry soakway pit 1.40m dia x 2.00m deep

Supplying all materials labour TandP and laying in trenches to level or slope unplasticized PVC pipes conforming to IS: 4985/2000 of the following outside dia for class 3(0.60mpa) including jointing with supply of approved solvent cement by non heat application method as per manufacturers specification providing and laying in trench cement concrete (1:4:8) with 40mm size hard granite metal in the Type C1 standard bedding surrounding or encasing including concrete for bedding and curing etc all complete as per PH specification and direction of the Engineer in charge.

160mm dia U-PVC Alround Concrete

Earth work in excavation of foundation in all kinds of soil within 50m initial lead and 1.5m initial lift including rough dressing & breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3m in depth and as per direction of the Engineer-in-Charge.

Extra lifts of 1.50 mtr or part thereof over the initial lift of 1.5 mtr in all kinds of embankments and road works and ordinary earthwork in general.

Supplying all materials, labour, T&P and providing cement concrete (1:3:6) with 4cm size hard granite metal including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12m size hard broken granite chips including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing brick work with K.B bricks having crushing strength not less than 75kg/cm² with dimensional tolerance ± 8 percent in cement mortar (1:4) including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing 12mm thick cement plaster (1:4) on brickwork including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing cement punning including watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing rigid and smooth centering and shuttering for R.C.C works including false work and dismantling them after casting including conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing M.S reinforcement for R.C.C work including cutting, bending, binding, and tying the grills and placing in position including cost of binding wire 18 to 20 gauge, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing cement concrete (1:2:4) with 12mm size hard broken granite chips for R.C.C works including hoisting, laying, watering, curing, conveyance of all materials to worksite, payment of royalty, taxes etc all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and providing,fitting and fixing 100mm x 100mm x 100mm SW Tee in wall including filling the recess with cement concrete (1:3:6) with 12mm size h.g chips all complete including watering, curing, conveyance of all materials to worksite, payment of royalty all complete as per specification and direction of the Engineer in charge

Supplying all materials, labour, T&P and making MS step iron in 20mm diameter MS steel bars and fixing into walls of man hole/septic tank duly embedded in cement concrete (1:3:6) complete as per specification and direction of the Engineer in charge.

Filling in foundation and plinth with excavated materials, moorum including watering and ramming as directed by the Engineer in charge

Sinking of 150mm dia Tube well through DTH Rig. Labour for drilling a perfectly vertical bore hole of specified dia for a specified depth below ground level through consolidated and unconsolidated rock with down the hole hammer drilling rig or combination rig as required to suit the site condition as per the direction of the Engineer in charge including use of own rig with its accessories, tools and plant and consumables etc for lowering of 200mm/150mm dia G.I/P.V.C/M.S casing pipes for housing fitted with socket and with or without well screen as per the necessity for soft, medium, hard and boulder formation (G.I/P.V.C/M.S casing pipes if required to prevent collapse of overburden is to be provided by the contractor including lowering and withdrawing after completion of the tube well), 200mm dia to 400mm dia in overburden portion including packing of gravel supplied by the contractor for 400mm dia bore only

45mtr to 150mtr

Lowering the following size of G.I/P.V.C/M.S housing pipes with or without slotted pipes as per the necessity from ground level up to 45.00m depth and fitted and fixed up in perfectly vertical position including cutting and threading of pipes and slotted pipes and supplying and fixing all jointing materials, tools and plant etc all complete and keeping the top of casing pipe threaded including plugging tube wells to prevent entry of foreign materials.

45 mtr to 150 mtrs

Cost of 150mm dia PVC ASTM (Sch-80) pipe

Cleaning and developing the tube well with supply of compressor worked till clear and adequate discharge is obtained from the tube well including supply and use of all necessary equipment and labour as per direction of the Engineer in charge

Supplying all materials and labour,tools and plant and providing sanitary sealing by cement concrete grouting of annular space around GI/PVC/MS housing pipe upto 5 mtrs below ground level(as per drawing)to plug the bore hole excluding cost of cement all complete as per direction of the Engineer in charge. Minimum one metre of casing pipe to be inserted in the bore into the rock the bottom to ensure sanitary sealing(excluding cost of cement which willbe supplied by the Department).

Supplying all materials and labour,tools and plant and providing sanitary sealing by cement concrete grouting of annular space around GI/PVC/MS housing pipe upto 5 mtrs below ground level(as per drawing)to plug the bore hole excluding cost of cement all complete as per direction of the Engineer in charge. Minimum one metre of casing pipe to be inserted in the bore into the rock the bottom to ensure sanitary sealing(excluding cost of cement which willbe supplied by the Department).

DOL control panel

2.50 sqmm cable

32mm dia steel short piece

32 mm dia HDPE Pipe

Bore Cap

C.I.Bracket

Rope Wire

Labour charges for lowering of submesible pumpset with pipes and cables etc. with testing and commissioning at site.

Supply all materials,labours,T&P and construction bore well protection chamber of the inside size 650x650x1000 height with cement concrete ( 1;3;6) using 40 mm size hard granite metal on foundation,1st class fly ash brickwork incement motar(1:3),with base cement concrete (1:2:4) useing 12 mm size h.g chips ,12 mm thick cement plaster (1:4) inside and out site ,R CC cover slab in (1:1.5:3) using 12 mm size h.g chips earthwork in excavation in all kinds of soil and refiling the cavity around the chamber including watering ,curing,convayance of all materials to worksite,payment of royalty,taxes etc all complete as per approved specification and direction of the engineer-in -charge. Bore well protection chamber.

Please Enable Macros to View BoQ information