Special Repair (Alteration and Modification) of HOD Room (Geography Department) in the Institute of Mountain Environment Building at Bhaderwah Campus Univeristy of Jammu CIVIL AND SANITARY WORK

Amount

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead as directed by engineer incharge.

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within the campus as per direction of Engineer-in-charge:In cement mortar

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m. (stacks of cleaned bricks shall be measured) : in cement mortar

Dismantling tile work in floors and roofs laid in cement mortar including Stacking serviceable material and disposal of unserviceable material within the campus as directed by engineer incharge .For thickness of tiles 8 mm to 25 mm

Fixing chowkhat in existing opening in brick/RCC wall with dash fasteners/chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhats and 2 nos. on each vertical member of window chowkhats), including cost of dash fasteners/chemical fasteners.

Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay (non modular) bricks

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as tomake it leak proof.

Half brick masonry with common burnt clay (non-modular) bricks of class designation7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Extra for half Brick masonry in superstructure above plinth level upto floor V level.

15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 4 ( 1 cement : 4 coarse sand)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as perarchitectural drawings and the directions of Engineer-in-Charge (glazing,panelling and dash fasteners to be paid for separately.) a) For fixed portion Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15) Powder coated aluminum (minimum thickness of powder coated 50 microns)

--------------do------------- b) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15) Powder coated aluminum (minimum thickness of powdercoated 50 microns)

Providing & laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen & the like consisting of: First Layer Applying cement slurry @ 4.40 kg/sqm. mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. Second Layer 20mm thick plaster 1.3 mixed with water proofing compound acro-1 in recommend proportion including rounding off junction of vertical and horizontal surface. Third Layer Applying blown or residual bitumen applied hot @ 1.70 kg/sqm on area both horizontal and vertical portion as directed by engineer incharge. Fourth Layer 3mm thick ACP SHEET (overlapping of joint of ACP sheet should be 100mm wide and pasted to each other with bitumen @ 1.70 kg/sqm on both vertical and horizontal surface .

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineerin-plate etc. complete as per the direction of Engineer-in-chargeWith Stainless Steel cover plate minimum 1.25 mm thickness.

Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer,(having brand logo with IS: 3564, embossed on the body,door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm),with double speed adjustment with necessary accessories and screws etc.complete :

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodized (anodic coating not less than grade AC 10 as per IS : 1868) aluminum lever handles of approved quality with necessary screws etc. complete.

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°,landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiralstair cases upto five level including curing but excluding the cost of centring, shuttering,finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing inposition and binding all complete upto floor v level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 infoundation and plinth and super structure upto floor v level Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Providing and laying double charge vitrified tiles in floors/skirting in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete(Make kajaria/somany/nitco/Johnson/RAK) Size of tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete of size 300x450/300x600 of minimum thickness 5mm .(Make Kajaria/rak/Johnson/sonmany/Nitco)

Providing and laying in floors /skirting polished antiskid Ceramic floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS:15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4( 1 cement : 4 coarse sand) including pointing the joints with whitecement and matching pigment etc., complete. (Make kajaria/somany/Nitco/Johnson/RAK) In colour such as White, Ivory, Grey, Fume Red Brown

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) and curing complete, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20/12.5 mm nominal size stone aggregate and 1:5:10 brick aggregate of minimum thickness 65mm .

Providing and applying white cement based putty of 1mm thick of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.(Make JK/Birla/Asian)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer(Asian/Nerolac/Berger).

Distempering with 1st quality Acrylic/oil bound washable distemper (ready-made) having VOC content less than 50 grams/litre of approved manufacturer and of required shade and colour complete as per manufacturers’ specifications, one or more coats on old work(Asian/Nerolac/Berger).

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work. (Asian/Nerolac/Berger).

Providing/Fixing glazing in aluminium door /window/ventilater shutters an d partition with PVC/Neoprene gasket etc complete as per architectural drawing and direction of engineer incharge (cost of aluminium snap beading shall be paid in basic item )with glass panes 5.0 thick float glass.

SANITARY WORK Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid , 10 liter low level white vitreous china flushing cistern and 40mm CP flush bend with fittings and C.I. brackets flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.(Make Cera hindware, parryware)

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste Coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 550x400 mm with 1 no.of 15 mm C.P. brass pillar tap.(JAGUAR/Hindware/Parryware/Cera)

Providing and fixing white vitreous china pedestal for wash basincompletely recessed at the back for the reception of pipes and fittings. (Hindware/Parryware/Cera)

Providing and fixing 600 x 450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete as approved by engineer incharge.

Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete as approved by engineer incharge.

Providing and fixing toilet paper holder with necessary screw etc C.P. brass

Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.(Make Astral/Prince/Supreme/finolex) A) PVC BEND 110 mm dia

----------------do--------------- 75 mm dia

B) Single tee with door 110mm dia

-------------do----------------- 75 mm dia

C) PVC Single Junction tee with door 110 x 110 x 110 mm dia

------------do----------------- 75 x 75 x 75 mm dia

D) PVC collar 110 mm dia

------------do----------------- 75 mm dia

E) PVC cowls 110 mm dia

--------------do---------------- 75 mm dia

F) PVC Door bend 110 mm dia

-------------do------------------ 75 mm dia

Providing and fixing PVC trap of self cleaning design with screwed down are hinged grading with or without vent arm complete including cost of cutting and making wood the walls and floors .(Make Astral/Prince/Supreme/finolex) 100mm inlet and 100mm outlet

-----------do-------------- 100mm inlet and 75mm outlet

Providing and fixing C.P CIRCULAR Type towel ring with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms as approved by engineering incharge.

Providing and fixing C.P towel rail complete with end brackets fixed to wooden cletes with C.P brass screws with concleded fitting arrangements

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.(Jindal/Tata/Lotus/Suyraprakash) 15 mm dia. nominal bore

------------do-------------- 20 mm dia. nominal bore

Providing and fixing ball volve ( brass) of approved quality with lever handle. 20mm nominal bore as approved by engineer incharge.

Providing and fixing G.I. Union in G.I. pipe including cutting andthreading the pipe and making long screws etc. complete (new work) 20 mm nominal bore

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931(hindware/Jaguar/Cera/Parryware.)

Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. (hindware/Jaguar/Cera/Parryware.)

Providing and fixing 15 mm nominal bore C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931 (hindware/ Jaguar/ Cera/Parryware.)

Providing and fixing 15 mm nominal bore C.P. brass angle valve forbasin mixer and geyser points of approved make conforming to IS : 8931 (hindware /Jaguar /Cera/Parryware.)

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes of minimum pressure 4kg per cm sq.conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (Astral/Prince/Supreme/Finolex) (i) Single socketed pipes 75 mm diameter

------------do------------- 110 mm diameter

Providing and fixing PVC p TRAP of approved quality (110 x 110) Make (supreme/finolex/prince/astral)

P/F Stainless steel grating 100mm dia

P/F stainless steel soap dish with necessary screws

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour: Waste coupling 31mm of 79 mm length and 62 mm breadth weighing not less than 45gms.

P/F PVC flush bend pipe for Europeon seat

P/F C.P jet (heavy duty) With PVC connection pipe to be fixed Europeon type wc seat

Providing and fixing uplasticized PVC connection pipe with brass unions 15 mm nominal bore of length 45cm to 60cm

Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg. (Jaguar/Hindware/PARRYWARE/Cera)

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarsesand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floatingcoat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover withframe (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

Constructing brick masonry manhole chamber for underground C.I Inspection chamber and bend with common burnt clay bricks of class designation 7.5 in cement mortar 1:4, C.I Cover with frame (light duty), 455 x 610 mm internal dimension, total wieght of cover with frame to be not less than 38 kg, RCC top slab with 1:1.5:3 mix, foundation concrete 1:5:10 inside plastering 12 mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design. Inside Dimension 500 x 700 mm and 40 cm deep for single pipe line with one or two inlets.

P/L cement concrete 1:4:8 mix 150mm thick all around PVC pipe including bed concrete as per standard design. 110mm dia or more.

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:3:6 or richer mix (i/c equivalent design mix)

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed by th engineer incharge. All kind of soil

Rattan Chand