REPAIRS TO COMPOUND WALL DRAIN FENCING PATH/HARD STANDING ETC AT CERTAIN OTM ACCN AT AUNDH UNDER GE MH RH KIRKEE

Amount

Demolition of brick work, PCC block masonry or stone boulder masonry built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles.

M&L for Pre-cast cement concrete block masonry of PCC 1:3:6 Type C1 using 20mm graded stone aggregate with solid blocks straight or curved on plan , exc 6m mean radius and exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

M & L for precast cement concrete solid block masonry exceeding 10 cm in width and set in cement mortar 1:6 but except precast cement concrete solid block. old solid block obtained from demolition shall be reused complete all as specified and directed.

Taking down cement plaster in any description incl racking out joints hacking for key and scrubbing down with water etc removing rubbish out side the premises complete all as specified and directed by Engineer-in-charge

M&L rendering 15 mm thick plaster on fair face of brick work or concrete surface in CM 1:4 and surface finished even and fair complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preparation of old plastered surfaces of wall and applying one coat of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

Dismantling fencing, wire mesh any type complete all as specified and directed by Engr in Charge

Dismantling wrought iron or mild steel work of any description not otherwise provided for in any position complete all as specified and directed by Engr-in-Charge.

S & F hot rolled low tensile structural steel of grade E165 as per IS 15911: 2010 as in hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. Wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar works complete all as specified and as directed.

M & L for cement concrete M-10 grade (Nominal Mix) using 40 mm nominal size graded crushed stone aggregate in foundation, filling and mass concrete for fencing post complete all as specified and as directed.

Supply only galvanized steel chain link fence fabric of mesh 50 x 50 mm, made out of 2.50 mm nominal dia of mesh wire complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

S&F mild steel bars 10mm dia as in bearing bars for chain link fencing complete all as specified and directed.

S & F in repair galvanized steel barbed wire with two strands of line wire of dia 2.24 mm and barbed with point wire of dia 2 mm at 75 mm spacing straining and fixing to any type of standards, rails, straining bolts including securing or tying at crossings with and provision of galvanised iron binding wire, GI staples or steel pins, etc. complete all as specified and as directed. Note : Two strand of line wire will be measured as one unit length.

Restraining & rescuring including making good staples etc. galvanized steel barbed wire with two strands of line wire of dia 2.24 mm and barbed with point wire of dia 2 mm at 75 mm spacing straining and fixing to any type of standards, rails, straining bolts including securing or tying at crossings with and provision of galvanised iron binding wire, GI staples or steel pins, etc. complete all as specified and as directed. Note : Two strand of line wire will be measured as one unit length.

S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in framed work such as grills, grating, etc., with ends of bars of shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework water tanks and similar work complete all as specified and directed by Engineer-in-charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

S & F for steel work of grade-3 as per IS 10748 in tubular trusses including special shaped washer etc. complete using ERW or HRIW welded tubes conforming to IS 1161: 2014 (Yst 240 Grade) complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws including dismantling old roof sheet of CGI/PGI complete all as specified..

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall, fixed with self tapping screws including dismantling old roof sheet of CGI/PGI complete all as specified.

M&L for preparation of untreated new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint ( 1st grade quality ) over a coat of red oxide primer complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing the same off the premises complete all as specified and directed.

M&L 75mm thick PCC M-7.5 grade (nominal mix) using 40 mm graded stone aggregate as in sub base all as specified.

M&L for Sand filling under floors or in foundation including consolidation. The thickness of sand cushion should not be less than 25mm for laying paver blocks.

M&L for 80mm thick coloured rubburised, glossy finish colour machine pressed interlocking pattern paver block any shape and size conforming to IS 15658-2006 of M-40 Grade incl all as specified and directed by Engineer-in Charge.

S&F Pre Polished Chequered cement concrete tiles glossy and rubburised finish colour 30cm x 30cm x 25mm thick, set, jointed and pointed in near cement slurry in floors over and including 15mm thick screed bed in CM 1:4 under tiles incl all as specified and directed by Engineer-in Charge.

M&L for 75mm thick PCC M-10 grade (nominal mix) using 40mm graded stone aggregate as in plinth protection/path finishing cement concrete surface even and smooth without using extra cement complete.

S&F in repair 75 mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, fixed on walls complete all as specified.

M & L for cement concrete in surface channels and drains in M15 grade (Nominal Mix) using 40 mm nominal size graded crushed stone aggregate complete all as specified and as directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitered/ stopped ends etc. complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in any position below or above ground floors, not exceeding 15 cm in depth and removing the material of the premises complete all as specified and as directed.

M & L for precast cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 complete with joints to match complete all as specified and as directed.

S&F TMT bars 6 to 8mm dia bar, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Demolition of Stone slabs and tiles of any description or thickness laided bedded and pointed in cement mortar in floors, aprons etc.

M&L Coloured Glazed ceramic tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm / 450 x 300 x 7mm thick, on vertical surfaces such as skirting, dados etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 10mm thick rendering as in backing coat in CM 1:4 complete all as specified and directed.

M&L for 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete fixed over and including backing coat of 10mm thickin CM 1:4 all as specified

M & L for ceramic fully vitrified tiles, coloured ceramic floor tiles (group B Ia), 300 mm x 300 mm x 10 mm in floors laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 set and jointed in neat cement slurry and pointed in epoxy mortar to match complete all as specified and directed.

S&F in repair Drain cover of size 600x600mm thickness 60-70 mm with fine finished with perforated holes 20/25mm and set the same at the site including removing old from site in any position complete all as specified and directed by Engr-in-Charge

S&F in repairs Medium duty precast cover slab of size 300x300mm thickness 60-70 mm with fine finished at the same at the place including removing old from site in any position complete all as specified and directed by Engr-in-Charge

Demolition of cement concrete (un reinforced) any description in any position not otherwise described including removing the spoil off the premises complete all as specified.

M & L for precast cement concrete louvers and jallies, 25 mm thick (measured solid) in cement concrete M-10 grade (Nominal mix) using 12.5 mm nominal size coarse aggregate including all mouldings but excluding frame and fixed in position using cement mortar 1:4 complete all as specified and as directed.

MANIYA CONSTRUCTION CO

V.R.PRAJAPATI AND CO.

M/S JAYCONSTRUCTION CO

Aishwarya Constructions

MAHESH DADAJI BACHHAV

L.K.R.TIWARI CONSTRUCTION

S.R.M.K Enterprises