PROVN OF UG SUMP AT LOW LIFT PUMP HOUSE, SPL REPAIR TO BLDG NO P-50 AND CERTAIN MINOR WORKSAT LEIMAKHONG MIL STN

Amount

B/R work

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and pre-cast concrete articles and removing unserviceable materials from site of work complete all as specified and directed.

M&L for brick work with subclass ‘B’ bricks, (locally available best quality) old size bricks straight or curved on plan exc 6 m means radius, built in cement mortar (1:6) complete all as specified and directed.

M & L for brick work with sub class ‘B’ brick, old size (locally available best quality) straight or curved on plan to any radius in half brick thick wall built in cement mortar (1:4) complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work.complete all as specified and directed.

M & L TMT mild steel bars 10 mm dia and over ,cut to length,bend to shape required, including cranking ,bending spirally for hooping for columns,hooking ends and binding with the including mild steel wire(annealed) not less than 0.9mm dia or securing with clips.complete all as specified and directed.

M&L for RCC M-15 (Nominal mix) using 12.5mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), fair finished surface of concrete complete all as specified and directed.

Taking down cement mortar plaster including raking out joints, hacking for key, scrubbing down with water etc.complete all as specified and directed.

M&L for rendering 15mm thick other than fair faces of brick work in cement mortar (1:4) using water proofing compound @2% by weight of cement as per manufacture instruction and finishing the surface even and smooth without using extra cement all as specified.(Using Dimapur Sand) [Note: WPC will be measured and paid separately)

M&L for rendering 15mm thick on fair faces of brick work in cement mortar (1:4) using water proofing compound @2% by weight of cement as per manufacture instruction and finishing the surface even and smooth without using extra cement all as specified.(Using Dimapur Sand) [Note: WPC will be measured and paid separately)

M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces in CM 1:6 finishing even and smooth without using extra cement. (Using Dimapur sand).complete all as specified and directed.

M & L for rendering 15mm thick plaster in cement mortar (1:4) on fair faces of brick work or on concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. (Using Dimapur Sand)

Supply only water proofing compound

M&L for rendering 5mm thick on fair faces of brick work or concrete surfaces wall or ceiling in CM 1:3 finishing even and smooth without using extra cement. (Using Dimapur sand).complete all as specified and directed

Demolition, Cement concrete (unreinforced) in ground floors and pavings n.exc 15 cm thickness below or above ground level complete all as specified and as directed by the Engineer-in-Charge.

M&L for 75mm th PCC 1:3:6 type C-2 using 40mm graded agg finished even and smooth w/out using extra cement complete all as specified and directed.

Forming contraction (Dummy) joints 65 mm deep x 10 mm wide and filled with sealing compound of grade 'A'complete all as specified and directed.

M& L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust complete all as specified and directed

M& L for Brushing neat cement slurry with 3.0 kg of cement per sq. metrecomplete all as specified and directed

M&L for Joint free Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store & rubish of the permises.complete all as specified and directed

M & L for non skid coloured ceramic tiles 7 to 8mm thick jointless (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L PCC 1:3:6 type C2 (40mm graded aggregate) 75mm thick as in sub base.complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in levelled course finish even and fair for tile finishes specified and directed

M & L for Glazed Coloured Ceramic tiles in vertical surface 350x250x7mm / 450x350x7mm thick jointless set and joint in neat cement slury and pointed in white or colour cement to match over and including 10mm thick plaster in CM 1:4 as backing coat to receive tiles complete all as specified and directed.

M&L for Joint free Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in Skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including rendering 10 mm thick on fair faces of brick work in CM (1:3) for receving vertical dado tiling complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors laid bedded and pointed in any mortar complete all as specified and directed.

M & L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , complete all as specified and directed.. .

M&L for screed bed 20mm thick in CM 1:3 complete all as specified and directed.

M&L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10mm thick cement screed in cm 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing ,complete all as specified and directed.

Taking down chowkat or frames w/o taking off shutter from the frame exceeding 1.5 Sqm not exc 4.0 Sqm each.complete all as specified and directed.

Taking down chowkhat without taking of shutter n exc 1.5 Sqm eachcomplete all as specified and directed.

Taking down shutter of any description exc 1sqm but not exc 2 Sqm each and removing unserviceable materials from site of work complete all as specified and directed.

M&L for taking down and refixidng in same opening wood shutter exc 1 sqm but not exc 2.00 sqm including easing & adjusting and refixing with same hardware etc.complete all as specified and directed.

S&F 2nd class hardwood plain solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints.complete all as specified and directed.

M&L 30mm thick Flush shutter solid core construction with block board core and plywood face panels commerical type on both sides.complete all as specified and directed.

M&L 25mm thick Flush shutter solid core construction with block board core and plywood face panels commerical type on both sides for cupboard.complete all as specified and directed.

S&F 35mm thick 2nd class HW glazed skeleton shutters open rebated and prepared to receive glass gazed etc but divided into squares with plain chamfered or rounded mitred and rebated sash bar any numbers edges of framing plain chamfered or rounded fitted with cut and mittered beads for sceuring glass guage etc. size of members as specified in SSR pt-I section 8 clause 8.20(a) fitted to chowkhats.complete all as directed and as specified.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm single piece extruded PVC profiles reinforced with 19 x 19mm MS square tube provided with EPDM rubber gasket weather seal through out the frame and the profile mitre cut at two corners and joined by inserting 2 nos 150mm long brackets of 15 x 15mm MS square tube inside 19 x 19mm MS square tube suitably screwed.complete all as directed and as specified.

Supply & fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes of size 15 x 15mm for top and bottom rails and 19 x 19mm for stiles, MS frame covered with 5mm thick single piece extruded PVC profile 'C' channel having a 5mm thick PVC sheet strip of 20mm width struck inside with solvent cement, forming stiles, and 5mm thick single piece extruded PVC profile for top rail, lock rail & bottom rail on either side, and 10mm (5mm x 2) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail; panelling of 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with PVC sheet beading, and joined together with solvent cement adhesive etc all as per manufacturer's instructions and drawings as shown in SSR Part-I 2009 complete all as specified and directed.

S&F in door or window frame of any description with aluminum sections, coloured powder coating not less than 50micron, and fixing in positions including all necessary cleats, lugs, beading, and jointing arrangements, complete all specified & directed.

S& F aluminium anodised sliding window, 3 track system and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc including all fitting . complete all as specified and directed.

Dismantiling wrought iron or mild steel work including of any description not otherwise provided for.complete all as directed and as specified.

S&F for framed work such as grills, grattings, etc. With ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of watertanks and similar work conforming to Fe-290, Gde-E-165.complete all as specified and directed.

M&L for 4.8mm thick plain tinted sheet ordinary quality in squares exc 0.5 Sqm each pane for aluminium window, complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wireand average width of aperture 1.40mm and fixed with stainless steel wire staples.complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue with hard drawn steel spring with 140mm overall length of cover plate. complete all as directed and as specified.

S&F 75mm butt hinges medium weight cold rolled mild steel.complete all as directed and as specified.

S&F MS butt hinges of size 100mm medium weight, cold rolled.complete all as directed and as specified.

S&F 150mm aluminium anodised of extruded section barrel tower bolts.complete all as directed and as specified.

S&F 200mm aluminium anodised of extruded section barrel tower bolts.complete all as directed and as specified.

S&F 150mm long alumiunium handles cast type anodised.complete all as directed and as specified.

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolt of extruded section or cast aluminium alloy and fixed 300mm long complete all as specified and directed (Make : CLASSIC or equivalent ISI marked)complete all as directed and as specified.

S&F mild steel helical door spring 300mm long ordinary rat tail pattern including roller plate.complete all as directed and as specified.

Supply and fixed 50 mm but hinges medium weight cold rolled mild steel. complete all as directed and as specified.

Supply and fixed 2nd class HW small fittings such as brackets of any type, latch and hing block, saved door and window stops and the like including all necessary labours articles n exc 200 cu cm each.complete all as directed and as specified.

S&F mild steel flat iron as in holdfast including screwing or welding.complete all as directed and as specified.

M&L provding cement concrete 1:3:6 type C1 using 20mm graded stone agg as in hold fast complete all as specified & directed.

Dismantling boarding any description in any position.complete all as directed and as specified.

M&L 18/19mm particle board medium density flat pressed single line layer type or three layer type with BWR type adhesive fixed with screws to timber frame work.complete all as directed and as specified.

M&L 0.9mm decorative laminated type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions.complete all as directed and as specified.

S&F 30m wide continuous (piano) hinges, mild steel, bright finish or electrogalvanised .complete all as directed and as specified.

S&F 40mm dia cupboard knobs fixed with nuts, screw and washer of mild steel bright finish.complete all as directed and as specified.

S&F Magnetic door catches of standard size for cupboard doorscomplete all as directed and as specified.

S&F in repair vitreous china squatting pan, orissa pattern size 580x440 white with integral foot rest (excluding flushing cistern and flush pipe) complete fixed.complete all as directed and as specified.

S&F, in repair light coloured vitreous china WHB white oval shape of 550mmx400mm (minimun) on new brackets excluding taps, waste china & plug including bracket etc complete all as specified and directed.

S&F in repair for Pillar taps, 15mm dia cast copper alloy with capstan heads chromium plated but fancy type down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts, screwed for iron pipe and fixed complete all as directed and as specified.

S&F PVC (SWR) floor trap with grating with incl jointing to waste pipe fixed in cement concerete (1:2:4) diameter of outlet pipe 75mm.

S&F PVC connection 15x600mm long with PTMT nuts & bolts Make: Prayag/Jindal

S&F in repair bib fancy type tap cast copper alloy CP brass 15mm bore of pipe complete all as specified.

S&F in repair for stop valve 15mm dia fency type chromium plated with long sank and cup concealed type complete all as specified and directed.

S&F in repair for brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union any colour for fixing with 15mm pipe.complete all as specified and directed.

S&F in repair CP brass towel rail 20mm dia 60cm long incl bracket fency type heavy weight as approved complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm incl existing and taking down complete all as specified.

S&F as in replacement stainless steel plate rack of size 24" x 36" x 10" complete all as specidfied and directed. (Make: Blue Star cat No KPR-312 or equivalent in Nirali/Jain Brothers/Prayag)

S&F as in repair shelf of PTMT fixed with and including chromium plated brass screw and wooden/plastic cleats ( min weight 300 gms). Make :- Prayag.

Taking up or down 15mm dia steel tubing and connections including cleaning for re-fixing or removal to store.complete all as specified and directed.

S&F tube medium grade galvanized with all fittings and fixed to walls or laid in floors of 15mm bore including cutting chasing in walls etccomplete all as specified and directed.

Refixing of 15mm steel tubing and including cleaning in positon (walls, ceiling and floor etc complete all as specified and directed.complete.

Cutting chases, pinning in, making good to facings of brick walls where required and pointing in CM 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed water conduit wiring, etc., and making good, cutting not exc 10 cm girth.complete all as specified and directed.

Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal to store.complete all as specified and directed.

S&F tube medium grade galvanized with all fittings and fixed to walls or laid in floors of 20mm bore including cutting chasing in walls etc

Refixing of 20mm steel tubing and including cleaning in positon (walls, ceiling and floor etc complete.

S&F in repair gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe of bore 20mm

S&F PVC soil, waste and rainwater (SWR) drainage pipes 110mm bore single socketd in any length with rubber rings joints fixed to wall and laid in floors weight of pipe not less than 0.70 Kg/Rmcomplete all as specified and directed.

S&F PVC soil, waste and rainwater (SWR) drainage pipes 75mm bore single socked in any length with rubber ring joints fixed to wall and laid in floors weight of pipe not less than 0.70 Kg/Rmcomplete all as specified and directed.

S&F PVC (SWR) branch bends any radius 110mm bore of pipecomplete all as specified and directed.

S&F PVC (SWR) branch piece single 'T' equal or unequal for 110mm borecomplete all as specified and directed.

S&F PVC (SWR) branch piece single 'T' equal or unequal for 75mm borecomplete all as specified and directed.

S&F PVC (SWR) branch bends any radius 75mm bore of pipecomplete all as specified and directed.

S&F PVC (SWR) vent cowl for 110mm bore pipecomplete all as specified and directed.

S & F in repairs fancy type decorative Drapary rod of 20mm dia for window and doors with curtain rings and decorative doom holders fixed to wall with screw complete.complete all as specified and directed.

M/L PCC (1:2:4) type B1 using 20mm graded stone aggregate as in benching of draincomplete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms moulds, mitered /stopped ends etc. complete all as specified and directed.

Demolition of cement concrete of any description in any position, concrete filling in sunken floor.complete all as specified and directed.

M&L for 15mm thick rendering to sides and bottom of sunken slab in CM 1:3 with water proofing compound, finishing the surfaces even and smooth without using extra cement,complete all as specified and directed.(WPC shall be measured seperately.

M&L for cement concrete type B0 using 12.5 mm graded aggregate in sunken floors 30mm thick complete all as specified.

S&F GI spouts 40mm dia projecting ateastn 20 cm clear of the wall.complete all as specified and directed.

M&L for applying two coats of hot bitumen 85/25 grade @ 1.70 Kg/Sqm over vertical surfaces and floor of sunken slab after laying all CI connection branch pieces etc after covering joints with PCC 1:2:4.complete all as specified

M&L PCC 1:7:12 type F 2 with bricks as in filling of sunken slab after laying carrying out required tests for CI pipes joints.

M&L for preparation of surfaces plastered or unplastered new surface on wall and applying two coats of oil bound distemper over a coat of 1mm thick wall care white putty all as specified and directed.

M&L for complete removal of existing finish, scrapping and making good surfaces on old surface of walls and applying two coat of oil bound distemper over a coat of 1mm thick wall care white putty all as specified and directed.

M& L for preparation of new surface including necessary scaffolding and applying finishing walls with Acrylic Smooth exterior paint of required shade New work (Two ormore coat applied @ 1.67 ltr/10 sqm over andincluding priming coat of exterior primerapplied @ 2.20 kg/10 sqm) complete all as per manufacturers instructionscomplete all as specified

M&L for removal of existing finish and preparation of old plastered surface including necessary scaffolding and applying two coats of acrylic exterior paint over a coat of primer (brand apcolite Apex manufactured by Asian or Brand weather coat manufactured by Berger or equivalent as approved by GE) complete all as per manufacturers instructions.

M&L for preparation of surfaces plastered or unplastered new surface on ceiling and applying three coats of white washing all as specified and directed.

M&L for preparation of surfaces plastered or unplastered old surface on ceiling and applying one coat of white washing all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new or previously untreated wood surfaces of any description not other wise described over 10 cm with or girth complete all as specified and directed.

M&L for applying one coats of synthetic enamel paint including preparation of old decorated wood surfaces of any description not other wise described over 10 cm with or girth complete all as specified and directed.

M&L for preparation of newly painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick set jointed with grey cement and pigments and pointed in neat cement slurry in floors including 20mm thick sreed bed in CM 1:6complete all as specified and directed.

Excavation over area n.exe 1.5m deep and getting out soft/loose soil.complete all as specified

Excavation over area exe 1.5m but n exc 3m deep and getting out soft/loose soil.complete all as specified

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm as in soft/loose soil.complete all as specified

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point.complete all as specified

M & L for hardcore of broken stone boulders exc. 63mm but not exc 100mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and remmed to a true surface, complete all as specified

M/L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate in foundation, filling and mass concrete complete all as specified.

M & L reinforced cement concrete (design mix M 30) (20mm graded aggregates) in foundation including rafts, footings, foundation beams, plinth beam etc.complete all as specified and directed.

Use and waste of formwork to sides of concrete foundation ,footing,base of column ,raft beams , sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter to rough finish surface of concrete flat. complete all as specified and directed

M&L reinforced cement concrete (design mix M 30) Walls, retaining walls, basement walls, ballast walls and the like any thickness above top of footings including attached pilasters and buttresses complete all as specified and directed

Use and waste of formwork to Formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc vertical or to better complete all as specified and directed

S & F 100 mm dia non return cast iron sluice valvecomplete all as specified and directed.

Supply & Laying,100mm Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floorsas specified and directed .

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L for PCC 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in foundation complete all as specified and as directed.

S & F steel work in tubular or square trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and as directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sucnk) forming holes with any attachement Fe 410W (Gde-E-250).complete all as specified and as directed.

S&F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified.

E/M Work

Material and labour for point wiring surface type with two single core 1.5 Sq mm (nominal area) FRLS PVC insulated and unsheathed,multi-stranded, copper conductor cable in and including suitable size PVC casing capping with all fittings and fixing accessories and suitable size PVC box for mounting switches, regulatorete including multi-strand PVC insulated unsheathed stranded copper cable as earth continuity conductor of size 1.5 Sq mm and connecting to light fitting/fans etc complete all as specified and directed for following : - ( colour code to be followed). Make - Havells / Polycab/ KEI/ Nicco/ Finolex

(a) One light point controlled by one, one way switch.

(b) One celling / exhaust fan point controlled by one, one way switch.

(c) One socket outlet 5 Amps 5 Pin on independent board

(d) One socket out let 5 Amps 5 pin on same board

(e) One bell / buzzer point controlled by one, one way switch.

All as per item No 137 here in before but with cable size 2.5 Sq mm for one 5 pin 15 Amps socket out let on independent board and multistrand insulated copper earth continuity conductor of size 2.5 sqmm all as specified and directed ( circuit to be laid seperatly ) Make - Havells / Polycab/ KEI/ Nicco/ Finolex

M/L for modular switch 6 Amps, single pole, 1 way,1 module . Make - Indo Asian / Legrand / Havells/Schneider

M/L for modular socket outlet 2/3 pin 6 Amps combined 2 module Make - Indo Asian / Legrand / Havells/Schneider

S & F modular socket multipurpose 3 pin 6/16 Amps 2 module. Make - Indo Asian / Legrand / Havells/Schneider

S/F ceiling rose , 3 phase/pvc/polycarbonate, isolated body Make - Indo Asian / Legrand / Havells/Schneider

S/F modular switch 1way, 16 Amps,1 module Make - Indo Asian / Legrand / Havells/Schneider

S/F modular Bell push 6A 1 module Make - Indo Asian / Legrand / Havells/Schneider

S&F modular white cover plate with frame of 8 module.

S&F modular white cover plate with frame of 6 module.

S&F modular white cover plate with frame of 3 module.

S&F modular white cover plate with frame of 1 module.

S & F blank speacer plate for single module Make - Indo Asian / Legrand / Havells/Schneider

S&F sheet metal enclosure (for DB's when MCBs to be used), single pole and neutral double door with rated bus bar 200 amps, 8 way, 240 Volts without MCB all as specified. ( Make - Indo Asian / Legrand / Havells/Schneider

S &F MCB SPN 40 Amps 240 volts 10 KA rating ( Make - Indo Asian / Legrand / Havells/Schneider )

S&F MCB SP 63 Amps 240 Volts 10 KA rating ( Make - Indo Asian / Legrand / Havells/Schneider )

S&F MCB SP 06 to 32 Amps 240 Volts 10 KA rating ( Make - Indo Asian / Legrand / Havells/Schneider )

S/F PVC Board 30 x 25 x 5 Cm depth complete . Make - Presto plast / Presto teak/ Modi / Plaza

Supply and fix lamp holer ,PVC/Polycarbonate type with cord grip cap suitable for pendent fitting including lamp lap.complete all as specify and directed.

S&F sheet metal enclosure (for DB's when MCCB/MCBs to be used), Triple pole and neutral double door, IP-54 ,1 way, 415 Volts with rated bus bar of size phase 150 Amp and neutral 300 Amps including MCCB 4 pole,160 Amps, 25 KA complete all as specify and directed..( Make - Indo Asian / Legrand / Havells/Schneider

S&F LED tube light fitting 20W LED 6500K basic all purpose surface and wall mounted LED robust and high perfomance batten LED luminair comprises of extruded channel in thermally conductive material glare and smooth lightwith complete . Make: CG: CCS-103-20-40-SL-DP-NWH/ Philips/Surya /Havells.

Supply ,laying and testing cable XLPE insulated,screened ,PVC bedded,galvanized steel strip or wire armoured electric power cables heavy duty 1100 volts grade with stranded aluminium conductor of size 25 sqmm 4 core.complete all as specify and directed.

Taking down ceiling/exhaust fan including dismantling all necessary electrical connections to facilitate repairs to ceiling/wall complete all as specify and directed.

Hanging only ceiling fan wall fan and connecting up ceiling rose or connecting to fan all as specified and directed.

Fixing only exhaust fan and connecting up ceiling rose or connecting to fan and making a whole cutting on the wall for fixing exhaust fan all as specified and directed.

S/F moduler fan step regulator,120 watt,2 module complete all as specified and directed.

6. M & L for sub main wiring with 2 single core 10.0 Sqmm PVC FRLS insulated unsheathed cable multi-stranded copper conductor drawn through and including PVC casing/capping of suitable size with all fittings and fixing accessories on roof, walls, ceiling etc. including 6.0 Sqmm PVC insulated unsheathed one core multistranded copper conductor earth wire complete all as specified and directed. (Note: Two run of single core cable and one run earth wire will be measured as one length)

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, poles struts, laying of cables/pipes, etc. not exceeding 10 sqm on plan and not exceeding 1.5m in depth and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in ;layers not exceeding 25cm as in soil complete all as specified and directed.

Removing excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5mtr above the starting point as in soils complete all as specified and as directed.

Supply and spresd sand in trenches as sand cushioning to underground cable for protection with dry fine sand and provide required cover after punning down 18CM will be measured and paid complete all as specified and directed.(Note:-Thickness of sand cushion after punning down will be measured and paid.)

Supply and laying well burnt sub class 'B' bricks (designated 75) locally available best quality, laid dry in trenches for protection of underground cable all as specified and directed.

Supply and fixing single pointed air termination aluminium rod, 12 mm dia, 300 mm long.complete all as specified and directed.

Supply and fixing aluminium strip 25 mm X 3 mm complete with saddles and fixing screws for fitting the strip.complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanized earth wire 4mm dia by means of galvanized iron or steel bolts nuts check nuts and washers and other end connected with earthing testing point including providing suitable testing points as directed including funnel, watering pipe of 20mm bore, light grade galvanized iron pipe, wire mesh charcoal of coal dust and common salt in alternative layer all around the earth electrode compacted thickness 15cm with concrete pit in PCC 1:3:6 type C1 50mm thick pre cast RCC 1:2:4 type B1 cover slab set in CM (1:4) re-enforcement with 8mm dia deformed bars @ 15cm C/C and suitable handle of 10mm dia MS round bars, including earth work in hard/dense soil as required complete all as shown in electrical plate No 3 of MES Schedule Part I and testing on completion all as specified and as directed.

S&F Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed.

S &F MCB SPN 32 Amps 240 volts 10 KA rating ( Make - Indo Asian / Legrand / Havells/Schneider )

S&F LED light fitting 1 x 22 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose .complete all as specified and directed.

S&F of 1100 volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheating of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than one meter apart including 4 mm suspension wire one twin core cable 2 core flat of 10 sqmm size Make - Havells / Polycab / KEI / Nicco/ Finolex. complete all as specified and directed

S&F ceiling fans 1200 mm sweep, 240 Volts, 50HZ, 3 blade with standard super silent motor including provision of 3 core flexible copper conductor cable of size 23/0.19 from ceiling rose to ceiling complete fixing arragement etc complete all as specified and directed. (Make: Havells Cat No. SS 390 or equivalent in Usha/Havells/ Bajaj/ Orient)

M/s RS Enterprises & Supplier

M/S BIJOYA LAXMI ENTERPRISE

MAURYA CONSTRUCTIONS

M/s Ritz Marketing

MANI PRASAD GUPTA

L BINOD CONSTRUCTION CO