Supply of Spares of coal mills (HP-1103) to RGTPP, Khedar, Hisar on annual contract basis.

Supply of Spares of coal mills (HP-1103) to RGTPP Khedar Hisar on annual contract basis, For Qty & detail please refer Annexure-1 of NIT in detail

Air Restriction Ring Large Size (Length Approx. 1800mm, Width 60mm, Thickness 28mm) (1 Set= 8 Nos.)

Air Restriction Ring Small Size (Length Approx. 1800mm, Width 35mm, Thickness 28mm) (1 Set= 8 Nos.)

Shroud Plate1360x120x10 (1 Set= 8 Nos.)

Vane Wheel Segment for Coal Mill (HP-1103), (1 Set= 8 Nos.)

Roller Retainer Ring For coal mills MOC: 16Mn

Mill Bowl hub Clamping Ring MOC- 16 Mn (1 Set=4 Nos.)

Scrapper With Liner Plate long, MOC:IS 1030, Gr-II, (Cast Steel) MOC of linear ISS 276 ASTM grade-3

Scrapper With Liner Plate, Short, MOC:IS 1030, Gr-II, (Cast Steel)MOC of linear ISS 276 ASTM grade-3

Journal Housing Liner Upper, MOC: Cast Steel as per IS 1030 Grade-2

Journal Housing Guard/Liner Lower, MOC- SS-304

Coal Mill Coupling Complete K3741.18.0

Tapper Bolt with SS Washer & Nuts for motor coupling

Locking Plate of Grinding Rolls L=274mm, T=32mm

Journal Bearing Keeper MOC: En24 Forged, OD-456mm, ID-105mm, PCD-232 mm, 8 nos. of holes of Size M32, thickness-40mm

Wear Resistant weld overlay plate with carbide layer of 6mm for Coal Mill, carbide layer on inner side of curved portion Dimensions-height:1500mm, width-1000mm, thickness-10mm (1 Set= 6 Nos.)

MS Flange for hot air diaphragm MOC- Mild Steel, Thickness-10mm, ID- 805mm, OD-944mm, PCD-890mm, No. of Holes-20 Nos. of size-M18.

Ventury Outlet for Coal Mill HP-1103 MOC- Carbon Steel

Filter Disc with Teflon Ring ID: 71mm, OD: 155mm, T: 8mm, Media: SS35 um {Required for round the clock filtration of lube oil (Servo Mesh XP-320) of coal Mills HP-1103}

Ventury Outlet Collar for Coal Mill HP-1103 MOC- Carbon Steel

Cover for Hot Air Diaphragm, MOC- Al Sheet, 2mm, OD-900mm

Ventury vane for coal mill, hardness= 60-62 HRC , hard thickness=15mm (1 Set=4 Nos.)

Seal Wear Ring of Coal Mill Journal Assembly Shaft, OD-470 mm, ID-390 mm, Width- 102 mm, MOC-SS304

Journal Housing Seal Cover for Journal Assembly of Coal Mills MOC:IS1020 Cast Steel/EN24

Wearable Adjustable Shrink (adjustable Orifice) for Coal Mill HP-1103, Coal PipeOD-710mm, Model-SMK Type-B {Wearable adjustable shrink to be supplied with 2 no. extra flange for connection/ installation with PC Pipe}

Mill Discharge valve (MDV) without power cylinder for Coal Mills HP-1103

Feeder Outlet gate without actuator

Mill Body Deflector Support Plate MS, 1 Set= 3 Nos.

Roller Liner Device For Coal Mill

Separator Body Liner-I, MOC: Ni Hard along with Weld plugs

Separator Body Liner-II, MOC: Ni Hard along with Weld plugs

Separator Body Liner-III, MOC: Ni Hard along with Weld plugs

Separator Body Liner-IV, MOC: Ni Hard along with Weld plugs

Separator Body Liner-V, MOC: Ni Hard along with Weld plugs

Separator Body Liner-VI, MOC: Ni Hard along with Weld plugs

Separator Body Liner-VII, MOC: Ni Hard along with Weld plugs

Separator Body Liner-X, MOC: Ni Hard along with Weld plugs

Separator Body Liner-XI, MOC: Ni Hard along with Weld plugs

Separator Body Liner-XII, MOC: Ni Hard along with Weld plugs

Liner RLD Type-I, MOC: Ni Hard along with Weld plugs

Liner RLD Type-II, MOC: Ni Hard along with Weld plugs

Liner RLD Type-III, MOC: Ni Hard along with Weld plugs

Liner RLD Type-IV, MOC: Ni Hard along with Weld plugs

Liner RLD Type-V, MOC: Ni Hard along with Weld plugs

Vane of Deflector Door MOC- High Alloying Wear Resistance Material Hardness:- 55-62 HRC (1 Set=40 Nos.)

Seals of hot shut off gate- L2000 mm, Width 115mm, Thickness-1.5mm, MOC-SS-304

Seals of hot shut off gate-L1800mm, Width 115mm, Thickness-1.5mm, MOC-SS-304

Seal Air Assembly for Gear Box For Coal Mill

Pyrite Chute/ Tramp Iron Spout for Coal Mill HP-1103 MOC- SS-304

Lower Skirt for Coal Mill HP-1103 (MOC:Carbon Steel) 1 Set= 4 Nos.

Idler Roller for RC Feeder Model:CS2036, 1 Set=12 Nos.

Bushing For RC Feeder and Coal MillGT1651807

Feeder Outlet Hopper of RC Feeder

Clean Out Conveyor Chain with Scrapper, MOC: Cast Alloy steel, Pin: En-08, 1 Set= 82 Pieces, 72 Chain links and 10 Chain scrapper

Expansion bellow for Pulverized Fuel Piping Specification: 04 Congulations (SS 304, Thickness-2mm). Medium: Coal+ Hot Air. Maximum Air Flow per Mill:125 Tonne per Hour. Pipe OD-710mm, Thickness of Connection end-16mm (Mild Steel). Position of fitment: Horizontal.

ERW Coal Pipe, Grade-API 5L, OD of Pipe-710mm, Thickness of pipe-16mm

Bearing Housing For RC Feeder and Coal Mill GT1651907

Eccentric Bearing Housing For RC Feeder and Coal Mill

L-150 coupling with rubber spider

Journal assembly top cover plate for coal mill HP-1103

Drive proket shaft for feeder outlet gate

Gear for feeder outlet gate

Gear for COC gearbox NDE

Helical gear both end set for COC gearbox

Shaft for COC chain reducer gearbox

COC coupling

Helical gear small DE for RC feeder gearbox

Helical gear NDE for RC feeder gearbox

Gear for COC gearbox DE

Cover for coal feeder outlet gate, GT1620607

Reducer body for coal feeder outlet gate, GT1621007

Reducer Cover for coal feeder outlet gate, GT1621207

Cover for Coal feeder inlet gate, GT161-C0607

Reducer body for coal feeder inlet gate, GT161-C0707

Reducer Cover for coal feeder inlet gate, GT161-C0907

Tube bleeder housing for coal feeder, GT1652907

Tube bleeder for coal feeder, GT1653007

Coal Feeder inlet end door (Complete)

Coal feeder discharge end door (Complete)

Trunion Bushing Journal K3741.14.4.0 , 600 MW ID-216 mm, OD-254 mm, Length – 325 mm, MOC of Tube: Seamless ASME SA 106 Gr. B, MOC of rubber:- Ethylene Acrylic Elastomer of Shore Hardness 50-55 A

J and J ENGINEERS (BID ID -1327978)

RAJU ENGINEERING WORKS PRIVATE LIMITED (BID ID -1327335)

UNITECH ENGINEERS (BID ID -1325154)

Shiv Shakti Engineering Works (BID ID -1326673)

ALFA ENGINEERING (BID ID -1327811)