Repairing and Renovation works of Boys Hostel at Fakhruddin Ali Ahmed Medical College and Hospital, Barpeta

Amount

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood

Providing and fixing 6mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 9.21.2 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Providing and applying white cement based purity of average thickness 1 mm of approved brand and manufacture , over the plastered wall surface to prepare the surface even and smooth.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Providing and fixing bright finished brass double acting spring hinges with necessary brass screws etc. complete : 150 mm

Providing and fixing bright finished brass flush bolts with necessary brass screws etc. complete : 250 mm

Providing and fixing factory made laminated veneer lumber glazed shutter conforming to IS: 14616 and TADS 15:2001 (Part B), using 4 mm thick float glass panes for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, all as per directions of Engineer-in-charge (Note:- Butt hinges and necessary screws shall be paid separately) 30 mm thick shutters

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 9.120.1 30 mm thick plain PVC door shutters

Suppply , Installation, Testting and Commissioning of 1200 mm sweeep, BEE 5 star rated ceiling fan with Brush Less Direct Currrent (BLDC) Motor, class of insultation :B ,, 3 nnos blades, 30 cm long down road ,2 nos. canopies ,shackle kit , safety rope , copper winding, Power factor not less than 0.9, Service Value (CMM/W ) minimum 6.85 , Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 3742019) , THD less than 10%, remote or electronic regulator unit for spend control and all remaining accessories including safety pin, nut bolts, washers , temperature rise =75 degree C (max) , insulation resistance more than 2 mega ohm , suitable for 230 V , 50 HZ, Single phase AC supply , earthening etc. complete as required .

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 5 A to 32 A rating , 240 /415 V,10 KA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Double pole

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm)

6 Module (200mm X75mm)

12 Module (200mmX150mm)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A Switch.

15/16 A Switch.

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet.

wiring for circuit / Submain wiring alongwith earth wire with the following sizesof FRLS PVS insulated copper conductor , single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mmm + 1 X 1.5 sq. mm earth wire.

2 X 2.5 sq. mmm + 1 X 2.5 sq. mm earth wire.

2 X 4 sq. mmm + 1 X 4 sq. mm earth wire.

Earthingwith G.I. earth pipe 4.5 metre long, 40 mm dia including accessories , and providing masonry enclosure with cover plate havinng locking arrangement and watering pipe etc. with chharcoal/ coke and salt as required.

Providing and lying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and refilling as required.

Supplying fitting and fixing of LED aluminium excruded smart bright batten tube light fitting (4 ft) as required and as directed by the department.

Supplying fitting & fixing of LED bulb 9W non dimmable in the existing batten / angle holder as required and as directed by the departments (philips or eqvt. Make)

Supplying fitting & fixing of wall mounted fan (plasttic) as required and as directed by the department (Orient/ Havellls /Crompton/ Usha or eqvt.Make.)

Supplying installation testing and coommissioning of pressure dia castt powder coated aluminium allloy hoousing forested PC diffuser IPSC/IP66 protectionn of street light including connection with 2.5 sq. mm 3 core PVC insulated rounded copper conductor Model No - SL90WLED757PASYBOTGGEM) (Havellls make ) as required and as directed by tthe ddeptt.

Supplying , installation, testing and commisiion of LED 50 W flood light of LED / MH/ HPSV luminiaries complete with all accessories such as balllast, capacitor , ignitor and driver as requuired complete with necessary suppport / foundation with 2.5 sq. mm PVC insulated S.C . copper conductor as required and as directed by the department ,( Havelles/PHILIPS/WIPRO/BAJAJ/CROMPTON/ HP/ SOLAR/JAQUAR make)

Sri Dhrubajyoti Kakati

SUKUMAR ENTERPRISE