NEW CONSTRUCTION OF AAM AADMI CLINIC AT VILLAGE SELBRAH BLOCK NAGAR PANCHAYAT DISTT BATHINDA

Select, At Par, Excess (+), Less (-) IOCL

Tender Inviting Authority: EXECUTIVE ENGINEER PROVINCIAL DIVISION, BATHINDA

NAME OF WORK:- NEW CONSTRUCTION OF AAM AADMI CLINIC AT VILLAGE SELBARAH BLOCK NAGAR PANCHAYAT DIST BATHINDA

Contract No: Composite Works

Name of the Bidder/ Bidding Firm / Company :

Sl. No. Work Name Item Code / Make Quantity Unit Rate Rs. P Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency BASIC RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category

Earth work in excavation in foundations trenches etc. in all kinds of soil where Pick-Jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm, layers with compaction including disposal of all surplus soil as directed within lead of 30 metres. Cum Excess(+) Full Conversion INR

Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar upto 40% taking outside the premises in 15 cm layers including ramming, watering and consolidated lead upto 1000 metres Labour Rate Only Cum. Excess(+) Full Conversion INR

Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar upto 40% taking outside the premises in 15 cm layers including ramming, watering and consolidated lead upto 1000 metres Cum Excess(+) Full Conversion INR

Cement Concrete 1:4:8 with stone ballast of size. 40 mm guage. using concrete mixing volumetric type Cum Excess(+) Full Conversion INR

First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth Cum Excess(+) Full Conversion INR

First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level. Cum Excess(+) Full Conversion INR

115 mm thick brick wall with every fourth course reinforced with hoop iron laid in1:4 cement mortar in superstructure 0.000 Sqm Excess(+) Full Conversion INR

Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering) Sqm Excess(+) Full Conversion INR

Centering and shuttering for sides and soffits of beam, beams, launching girders, bressumers, lintels. Sqm Excess(+) Full Conversion INR

Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc. Sqm Excess(+) Full Conversion INR

Centring and shuttering for parapet, fascias and other similar items including edges. Sqm Excess(+) Full Conversion INR

Reinforced cement concrete M-25 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth Cum Excess(+) Full Conversion INR

Reinforced cement concrete M-25 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure. Cum Excess(+) Full Conversion INR

Cold twisted detormed (Ribbed/Tor steel) Bars (Fe 500 grade as per IS 1786-2008) , for R.C.C works,where not including in the complete rate of RCC including bending and binding placing in position complete Qtl Excess(+) Full Conversion INR

Damp proof course 4cm thick of cement concrete 1:2:4 with 2 coats of bitumen 20/30 penetration at1.65 Kg per Sqm laid hot and sanded 0.999 Sqm Excess(+) Full Conversion INR

12.5 mm thick cement plaster 1:5 Sqm Excess(+) Full Conversion INR

20mm thick cement plaster 1:5 in two coat work Sqm Excess(+) Full Conversion INR

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish Sqm Excess(+) Full Conversion INR

Providing andapplying plaster of paris (ISI markedsuchasJK,Kohinoor,Maharajaetc.) punning 6mm thickness over plastered surface to prepare the surface even and smooth complete in all respect as per the directions of Engineer-in-charge. Sqm Excess(+) Full Conversion INR

Applying priming coat with cement primer in all shade on newly plastered or concrete exterior surface Sqm Excess(+) Full Conversion INR

Wall painting with plastic emulsion paint of approved brand and manufacturer togivean even shade (two or more coats) Sqm Excess(+) Full Conversion INR

Finishing walls with acrylic smooth exterior paintof requiredshadewithtwoormorecoats applied @ 1.67 litre/10Sqm over and includingbasecoatofwaterproofingCement Paint applied @ 2.20 Kg/10 Sqm Sqm Excess(+) Full Conversion INR

Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position 0.000 Qtl Excess(+) Full Conversion INR

Supplying and fixing of Japani sheet frames (Chowkat)consisting of 18gauge (1.25mm) thick steel sheet of the specified section (standard designlatest), including ironlugs(holdfasts) iron hinges conforming to PWD specifications including bolts for fixing steps, lock notch provision for receiving tower boltsand finished, fixed in position including the cost of cement concrete1:3:6for filling inth eframe and cement concrete 1:2:4 for lugs complete to the satisfaction of Engineer-in-charge

Door and window frame of size113mmx60mmx with 35mm wide single rebate Rmt Excess(+) Full Conversion INR

Doors and windows frame of size 151mm x 60mm with 35 mm wide double rebate weighing 3.95 kg per meter. Rmt Excess(+) Full Conversion INR

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In Charge. (Glazing and paneling to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug / neoprene gasket required Kg Excess(+) Full Conversion INR

Providing & fixing ACP Sheets of various thickness High Class ISI marked complete in all respect as per the directions of Engineer-in-charge (i) 6mm thick ACP Sheet 0.000 Sqm Excess(+) Full Conversion INR

Providing Polyester Powder coating 50micron any coloured specified to alumnum section of various sizes including carriage of material from market to workshop & workshop to site of work. 0.999 kg Excess(+) Full Conversion INR

Factory manufactured flushdoor fixed in position iron hinges, etc (excluding the cost of any fittings other than specified abovebut including labour for fixing the same in position 35 mm thick Sqm Excess(+) Full Conversion INR

Wire gauge Hollock wood door shutter without springs housed in chowkhat A 35 mm thick Sqm Excess(+) Full Conversion INR

Hollock wood doors shutter windows shutter includinghinges, screws, chocks, cheats,stopscordsetc.completefixedin position. panelled, glazed or glazed and panelled 35 MM thick Sqm Excess(+) Full Conversion INR

Providing &Fixing glass panes with nails and putty or wooden strip complete inall respect 5.0mm thick Plate glass (INDIAN) Sqm Excess(+) Full Conversion INR

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete (c) I.S.I Designation No. III (size of door 851mm to 1000mm) each Excess(+) Full Conversion INR

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :300mm x 16mm each Excess(+) Full Conversion INR

Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt) For shutter area above 0.50 Sqm 0.000 Sqm Excess(+) Full Conversion INR

Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consistingofwhite lead, linseedoil,Varnish, andChalkMitti includingfinishingthesurface to required finish complete. Sqm Excess(+) Full Conversion INR

Applying pink primer or aluminum priming coat on woodwork including preparation of surface knotting and stopping etc. Sqm Excess(+) Full Conversion INR

Applying priming coat with metal primer on new steel or iron work including preparation of surface. Sqm Excess(+) Full Conversion INR

Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. Sqm Excess(+) Full Conversion INR

Providing & fixing 16 gauge stainless steel pipe railing of grade 304 duly fixed on steps with the help of bolts grouted on steps with hand rail and newel post of 50mm dia Stainless steel pipe, Balusters of 40mm dia Stainless steel pipe and guard 3 Nos of 15mm dia Stainless Steel pipe complete in all respect kg Excess(+) Full Conversion INR

Base course of floor consisting of 100mm thick cement concrete 1:8:16 with stone aggregate 40mm gauge and 100mm sand filling using mechanical mixer for mixing of material Sqm Excess(+) Full Conversion INR

Conglomerate floor 40mm thick cement concrete topping 1:2:4 using mechanical mixer for mixing of material Sqm Excess(+) Full Conversion INR

Providing and Laying Out Door precast designer chequered tiles of any size & any shape 25mm thickness having top layer of white cement mixed with pigment, laid on 20mm thick bed of ordinary cement mortar 1:3 (1 ordinary cement: 3 fine sand), joints grouted with white cement slurry containing pigment to match the shade complete in all respect as per specifications and to the entire satisfaction of engineer-in-charge. Sqm Excess(+) Full Conversion INR

Marble stone flooring with 12-15 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Udaipur Green Marble Tiles of thickness 12mm to 15mm Slabs sizes above 0.50 Sqm Sqm Excess(+) Full Conversion INR

Providing and laying vitrified floor tiles indifferent sizes in light colour shades made usingFull Body Technology (thickness to be specifiedby the manufacturer) with water absorption’s lessthan 0.08% and conforming to IS : 15622 ofapproved make in all colours and shades, laid on20mm thick cement mortar 1:4 (1 cement: 4 finesand), complete. ( Full body vitrified tiles havepigment in entire body / thickness of tile whichmakes chips and scratches less noticeable and make na ideal choice for high traffic zones.) Sqm Excess(+) Full Conversion INR

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. A Size 600x600 mm Sqm Excess(+) Full Conversion INR

Providing and fixing mineral fibre false ceiling tiles at height upto 4 mtr With 16 mm thick beveled tegularmineral fibre Anti-microbial false ceiling tile of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, of 99%, Light Reflection Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portionof all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. Sqm Excess(+) Full Conversion INR

Providing and Fixing ceiling consisting of 12.5mm thick Gypsum Board of any size G.I. Cradling hanged from the ceiling by means of G.I.hanger complete asper drawings, specifications and to the entire satisfaction of engineer-in- charge. Sqm Excess(+) Full Conversion INR

Top Khurra 0.6mx0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50.00 thick cement concrete 1:8:16 each Excess(+) Full Conversion INR

Bottom khurra on ground 1.2m 0.6m consisting of bricks on edge laid in cement mortar 1:3 over 7.5 cm cement concret 1:8:16 including 12.5mm thick cement plaster 1:3 each Excess(+) Full Conversion INR

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified. Rmt Excess(+) Full Conversion INR

Providing and fixing 110 mm dia . U.P.V.C Rain water pipe of 4 kgf./Sqm as per IS:4985 including jointing during masonary complete as per specifications and to the entire satisfaction of Engineer-in- charge. Rmt Excess(+) Full Conversion INR

Providing and fixing 110 mm dia. U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. each Excess(+) Full Conversion INR

Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25 mm mud plaster 7.5 cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg. /Sqm top of R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing Sqm Excess(+) Full Conversion INR

Signage Excess(+) Full Conversion INR

Providing & fixing ACP Sheets of various thickness High Class ISI marked complete in all respect as per the directions of Engineer-in-charge. 3mm thick ACP Sheet Sqm Excess(+) Full Conversion INR

Writing matter on front signage Using high intensity Microprismatic grade retro reflective Sheeting Type IV as per ASTM D 4956 09 and as per IRC 67 2012 Sqm Excess(+) Full Conversion INR

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-35 grade machine made rubber moulded smooth finish with strong vibratory process or with vibrohydraulic compaction machine and of approved size and design / shape laid in ordinary Grey and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-Charge . IS Code: 15658 (2006) Sqm Excess(+) Full Conversion INR

Extra labour for projected nosing of stair case of any shape and design. Rmt Excess(+) Full Conversion INR

Providing and fixing commercial plywood 18mm thick Sqm Excess(+) Full Conversion INR

Providing & Fixing decorative high pressure laminatedsheet 1mmSF thick withhighdensityprotectivesurface layer and reverse side of adhesive bonding qualityconforming to IS : 2046TypeS, including cost of adhesive of approved quality. Sqm Excess(+) Full Conversion INR

Providingand fixingspecial qualitybright finished brass cupboard or ward robe lockswithfour leversof approvedquality includingnecessaryscrewsetc. complete in all respect as per the directions of Engineer-in-charge. Nos. Excess(+) Full Conversion INR

Providing & fixing 4" stainless steel tower bolts ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge. Nos. Excess(+) Full Conversion INR

Providing & fixing 6" stainless steel handles ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge. Nos. Excess(+) Full Conversion INR

Earth work in excavation in foundation trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2mtr depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15cm. layers with compaction including disposal of all surplus soil as directed within a lead of 30 metres. CUM Excess(+) Full Conversion INR

Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar upto 40% excaveted from foundation and taken only from outside the building plinth in 15cm layers including ramming, watering and consolidating lead up to 30mtrs CUM Excess(+) Full Conversion INR

Cement concrete 1:8:16 with 40mm gauge stone aggregate using concrete mixer volumetric type. CUM Excess(+) Full Conversion INR

1st class B.B work laid in cement sand mortar 1:6 foundation and plinth. CUM Excess(+) Full Conversion INR

Damp proof course 40mm thick of cement concrete 1:2:4 with water proofing compound as per manufacture guidelines. SQM Excess(+) Full Conversion INR

1st class B.B work laid in cement sand mortar 1:6 superstructure.(Ground Floor) CUM Excess(+) Full Conversion INR

12.5mm thick cement plaster 1:5 SQM Excess(+) Full Conversion INR

20mm thick cement plaster in 1:5 in two coats work. SQM Excess(+) Full Conversion INR

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish Sqm Excess(+) Full Conversion INR

Finishing walls with exterior decorative cement based paint such as snowcem, robbiacem etc. two or more coats to give an even shade SQM Excess(+) Full Conversion INR

Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position Qtl. Excess(+) Full Conversion INR

Furniture Excess(+) Full Conversion INR

Chair for Receptionist , Pharmacist & Lab Assistant Excess(+) Full Conversion INR

Chair for Receptionist , Pharmacist & Lab Assistant- Providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with back support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be made of black integral metal insert polyurethane arm completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-4 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standard. The pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle Dia. 650±15 mm and fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 460±10 mm(W) X 450±10 mm(D) and back size shall be 460±10 mm(W) X 400±10 mm(H) from seat. Seat height = 460±10 mm, overall height shall be = 810±10 mm of reputed brand/make or equivalent except Chinese complete as per approved drawings by furniture committee Nos. Excess(+) Full Conversion INR

Waiting Area chair 3 seater- Supplying & Placing three seater bench. The seat and back shall be made up of high quality cold rolled MS perforated sheet of 1.2mm thick, pressed and welded to form the shape. The seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. The armrest shall be made up of mild steel powder coated tube with 1.2mm thick. The base structure shall be supported by MS powder coated with 40-60µ (DFT). There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 440±10 mm(D) X 405±10 mm(H) from ground. Overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm of reputed brand/make except Chinese complete as per approved drawings by furniture committee Nos. Excess(+) Full Conversion INR

Waiting Area chair 2 seater - Supplying & Placing two seater bench. The seat and back shall be made up of high quality cold rolled MS perforated sheet of 1.2mm thick, pressed and welded to form the shape. The seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. The armrest shall be made up of mild steel powder coated tube with 1.2mm thick. The base structure shall be supported by MS powder coated with 40-50µ (DFT). There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 450±10 mm(D) X 430±10 mm(H) from ground. Overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1180±10 mm of reputed brand/make except Chinese complete as per approved drawings by furniture committee Nos. Excess(+) Full Conversion INR

Doctor Table- Supplying & Placing executive table with credenza unit in completely knock down conditions with table size - 1800mm x 750mm x 750 mm and side cabinet 900 mm x 400 mm x 750 mm that is to be assembled at site. The worktop shall have the size 1950mm X 900mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on CRCA powder coated rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick. The table shall be clad with 1mm thick modesty panel which provide structural support for the table. It should be 1mm thick with star perforation CRCA powder coated sheet in linear shape. The understructure shall consist of loop leg and C-type leg made up of CRCA powder coated triangular shape pipe having cross-section area 53mm X 53mm X 75mm with 1.6mm thick. There shall be shoe provided at the base to avoid scratches on the floor. Side top shall be provided with an overall size 900mm X 400mm X 750mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823. It shall be supported on peg which is mounted on credenza unit. The credenza unit shall have overall size 900mm X 400mm X 750mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 box drawer, 1 filing drawer and 1 shutter. The drawer shall be operated with roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The shutter shall be operated by SS handle and concealed crank hinge. The credenza unit shall be mounted over CRCA powder coated U shape leg having cross-section area 53mm X 53mm x 75mm with 1.6mm thick. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380 of reputed brand/make or equivalent except Chinese complete as per approved drawings by furniture committee Nos. Excess(+) Full Conversion INR

Main chair for Doctor- Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40Kg/m³ in back. The seat and back shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with full back support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be made black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled, confirming to ANSI/BIFMA Standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 470±10 mm(W) X 460±10 mm(D) and back size shall be 460±10 mm(W) X 610±10 mm(H) from seat & overall height = 1050±10 mm of reputed brand/make or equivalent except Chinese complete as per approved drawings by furniture committee Nos. Excess(+) Full Conversion INR

Visitor Chair for Doctor- Providing and supplying a visitor chair with ergonomic design, user comfort & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 32Kg/m³ in back. The same shall be upholstered with crape fabric tapestry 0.6mm thick and 235 GSM. The seat and back of chair shall be supplied with polypropylene beam on edges and the backrest shall be made by keeping the natural curvature of the spine. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine. The armrest shall be made of black integral polypropylene arm mounted on powder coated round pipe frame completely joint with seat and back. The frame structure shall be cantilever support type made up of MS CRCA powder coated round pipe of Dia. 25.4mm with 1.6mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor . The seat size shall be 480±10 mm(W) X 450±10 mm(D) and back size shall be 480±10 mm(W) X 400±10 mm(H) from seat & overall height = 820±10mm, overall depth = 600±10 mm of reputed brand/make or equivalent except Chinese complete as per approved drawings by furniture committee Nos. Excess(+) Full Conversion INR

Examination Table for Doctor Room - Providing and Placing in position Examination Table with two section top with fix mattress ( Overall size of the table shall be 1830 mm L x 560-600 mm D x 810-850 mm H). The examination table shall be made of sturdy structure and shall have a ratchet mechanism for tilting the backrest. Leg frame and intermediate frame shall be made of 40x40 section 2 mm thick M.S. ERW Tube. Nylon 6 leg shoe shall be provided to avoid wear and tear of the floor. Lying surface shall be made of 1.2 mm thick M.S. ERW Tube. Ratchet shall be made of 5 mm thick M.S. ERW tube and shall provide back tilt at 0º, 15º and 30º asjustment positions. Table shall be epoxy polyxter powder coated and shall have a maximum load bearing capacity of 135 kgs. The bed should be provided with 40 density 50mm thick PU foam mattress which should be covered by heavy helium material which is water proof, flame retardant, vapour & X-ray permeable. The zip & stiches for the mattress cover should be concealedof reputed brand/make or equivalent except Chinese complete as per approved drawings by furniture committee Nos. Excess(+) Full Conversion INR

Stool for Doctor, Pharmacist Room & in Sampling Room - Revolving Stool made of 32 od mm and 25 od mm MS pipe, top made of SS steel plate heavy gauge frame powder coating of reputed brand/make or equivalent except Chinese complete as per approved drawings by furniture committee Nos. Excess(+) Full Conversion INR

Storage for Medicine/ Customised lab table - Providing, supplying and placing storage almirah. The overall size of the Almirah shall be 600mm (W) X 900 mm (D) X 750mm (H). The Almirah shall be supplied with 2 nos. of wodden doors with 2 nos. of adjustable shelves i.e. 3 loading compartments. It Should be of 25mm thcik prelaminated Particle board of grade II of IS 12823 The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength complete as per approved drawings by furniture committee Nos. Excess(+) Full Conversion INR

Big Storage for Medicine 1 No. no in Pharmacy- Providing, supplying and placing steel almirah. The overall size of the Almirah shall be 915 mm (W) X 485mm (D) X 1980mm(H). The Almirah shall be supplied with 2 nos. of glass doors with 4 nos. of adjustable shelves i.e. 5 loading compartments. The glass used shall be 5mm thick clear. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-50µ thick of reputed brand/make except Chinese complete as per approved drawings by furniture committee. Nos. Excess(+) Full Conversion INR

Providing and fixing at site the Reception Table plan dimensions as 5’-6” x 1'9" & 2'9" x 1’5” and height 2’- 6” with storage, drawers, space for legs, etc complete as per drawing. The table should be sturdy and stable and will comprise of knot-free teak wood, wherever required, 19mm/ 12mm/ 6mm water proof ply and 1mm laminates of Make and Colour to be approvedby Architect/ Engineer-in-charge. The item also includes hardware such as drawer channels, handles, etc of make and design to be approved by Architect/ Engineer-in-charge. The item also includes all types of consumables such as nails, screws, fevicol, tape, etc and polishing, if required.Grooves, wherever required as per drawing, are also included in the item.complete as per drawing/design (Attached) as decided by Furniture Procurement Committee. Nos. Excess(+) Full Conversion INR

Providing and fixing at site the Pharmacy table plan dimensions as 1200 x 600 x 750 mm with projected shelve, storage, drawers, space for legs, etc complete as per drawing. The frame structure shall be made up of MS CRCA TATA/ BHUSHAN 0.8 mm thickness . The Counter should be sturdy and stable and will comprise of knot-free teak wood, wherever required, 19mm/ 12mm/ 6mm water proof ply and 1mm laminates of Make and Colour to be approvedby Architect/ Engineer-in-charge. The item also includes hardware such as drawer channels, handles, nails, screws, fevicol, tape, etc polishing and Grooves if required., wherever required as per drawing of reputed brand/make except Chinese decided by Furniture Procurement Committee. Nos. Excess(+) Full Conversion INR

Providing and placing moveable 3-fold screen of CRCA/MS fame with green coloured curtain, having arrangements that it can be removed for washing and refixed. The overall dimension of the 3-fold screen will be 1675mmx2450mm around examination table. The Curtain material should be of Cotton fabric and Specially coated which do not allow any bacteria hold on it. The MS frame will be 19.05mm (OD) x 1.22mm and base material 25mm (OD) x 1.22mm of MS powder coated in colour over priming coat complete as per approved drawings by furniture committee. Nos. Excess(+) Full Conversion INR

Providing and fixing Roller Blinds at the designated locations with fabric/ texture complete as per approved drawings reputed brand/make by furniture committee. Sft Excess(+) Full Conversion INR

Electrical Services Excess(+) Full Conversion INR

RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Excess(+) Full Conversion INR

Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½" deep for walls and CI 3" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- Excess(+) Full Conversion INR

Wiring fan point (With fan box) Each Excess(+) Full Conversion INR

Wiring light point Each Excess(+) Full Conversion INR

Wiring call-bell point Each Excess(+) Full Conversion INR

Wiring 6 Amp. wall socket point Each Excess(+) Full Conversion INR

Wiring 6 Amp. Plug control comprising wall socket point Each Excess(+) Full Conversion INR

Wiring 16/20 amp. power plug control point Each Excess(+) Full Conversion INR

RECESSED COMPUTER SUPPLY TERMINAL POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): Excess(+) Full Conversion INR

Wiring Computer supply terminal points recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10/16/20Amp. Switches and blanking plate etc., and covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):- Excess(+) Full Conversion INR

Wiring Computer terminal point having 3 Nos. 6Amp. 2/3 universal socket (shuttered), 1No. 16 Amp. switch with indicator and 1No. blanking plate (Modular accessories). Each Excess(+) Full Conversion INR

RECESSED AIR CONDITIONER SUPPLY TERMINAL POINT (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): Excess(+) Full Conversion INR

Wiring air conditioner supply terminal point recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 25Amp. combined/ universal Socket (shuttered) and modular motor starter 25Amp. (2Module), covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):- Excess(+) Full Conversion INR

Wiring AC supply terminal point having 1No. 25Amp. universal Socket (shuttered) erected at AC height and 1No. Motor starter 25Amp. erected at switchboard height. Each Excess(+) Full Conversion INR

RECESSED TV, TELEPHONE & NETWORKING SOCKETS OUTLET POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): Excess(+) Full Conversion INR

Supply and erection of TV socket, Telephone socket and Networking socket points in powder coated/anodized concealed metal boxes recessed in wall required for suitable number of modules (Modular accessories) for having TV sockets, Telephone sockets RJ11 & Networking socket RJ45 (one module), covered with Frame Plate and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- Excess(+) Full Conversion INR

Wiring Telephone socket point RJ11 (one module) Each Excess(+) Full Conversion INR

Wiring Networking socket point RJ45 (one module) Each Excess(+) Full Conversion INR

SUPPLY AND ERECTION OF WIRING ACCESSORIES: Supply and erection of switches, sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.:- Excess(+) Full Conversion INR

Ceiling Rose (Flush Piano type) Each Excess(+) Full Conversion INR

Call Bell 220/230 volts AC Ding Dong Each Excess(+) Full Conversion INR

COPPER WIRES & CONDUIT PIPE: Excess(+) Full Conversion INR

PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE: Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- Excess(+) Full Conversion INR

Overall size 1.5sq.mm (Un-sheathed) mtr. Excess(+) Full Conversion INR

Overall size 2.5sq.mm (Un-sheathed) mtr. Excess(+) Full Conversion INR

Overall size 4sq.mm (Un-sheathed) mtr. Excess(+) Full Conversion INR

Overall size 10sq.mm (Un-sheathed) mtr. Excess(+) Full Conversion INR

PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- Excess(+) Full Conversion INR

Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) Flushed mtr. Excess(+) Full Conversion INR

Heavy gauge PVC conduit pipe 40mm dia. (ISI marked) Flushed mtr. Excess(+) Full Conversion INR

Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) On Surface mtr. Excess(+) Full Conversion INR

Supply and erection of PVC flexible pipe complete without compression glands, locking arrangement, check-nuts as required:- Excess(+) Full Conversion INR

PVC flexible pipe 25mm dia. mtr. Excess(+) Full Conversion INR

PVC flexible pipe 40mm dia. mtr. Excess(+) Full Conversion INR

HEAVY GUAGE WELDED CONDUIT PIPES: Supply & erection of Heavy guage welded conduit pipe (ISI marked) as per IS:9537:Part-II for wiring purposes including bends, junction boxes, Steel hooks, GI saddle clamps and other petty materials etc., where necessary including painting as per PWD General Specifications:- Excess(+) Full Conversion INR

Supply & erection of 19/20mm dia. M.S. conduit pipe (1.6mm thick), white painted suspension rod for ceiling fan. mtr. Excess(+) Full Conversion INR

Copper Earthing- Earthing with 8 SWG (4mm dia.) electrolytic copper wire thimbled (1No. copper thimble with suitable size steel bolt, washers & double nut) with 30cm x 60cm x 2mm thick copper plate (made cylindrical) burried below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the copper wire run through 20mm dia. G.I. pipe (A-Class) recessed in wall and in floor etc., up to suitable Length in metre (including bore Length). G.I. pipe 20mm dia. (A-class) of suitable Length should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:- Excess(+) Full Conversion INR

Earthing with 8 SWG (4mm dia.) copper wire thimbled with 30cm x 60cm x 2mm thick copper plate burried 4.50 metre (14.76 feet) below ground level (up to 8metre in Length) with G.I. pipe 20mm dia. (A-class), 3metre long Each Excess(+) Full Conversion INR

Fixing additional Length of earthing with 8 S.W.G. (4mm dia.) (Flushed) copper wire in G.I. pipe with sockets, elbows, steel hooks and GI saddle clamps including painting etc.:- Excess(+) Full Conversion INR

Additional Length copper wire 8 S.W.G. (4mm dia.) in 20mm dia. G.I. pipe (On Surface) Each Excess(+) Full Conversion INR

Additional Length copper wire 8 S.W.G. (4mm dia.) in 20mm dia. G.I. pipe (Flushed) Each Excess(+) Full Conversion INR

MCB'S & MCB DISTRIBUTION BOARDS: Excess(+) Full Conversion INR

MINIATURE CIRCUIT BREAKERS: Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- Excess(+) Full Conversion INR

MCB Single Pole 6-32amp. (10kA, Curve-C) Each Excess(+) Full Conversion INR

MCB Double Pole 40amp. (10kA, Curve-C) Each Excess(+) Full Conversion INR

MCB Four Pole 50, 63amp. (10kA, Curve-C) Each Excess(+) Full Conversion INR

SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB/ RCBO/ RCCB's:Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, color- coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:- Excess(+) Full Conversion INR

TP&N Horizontal Double Door Distribution Board 4 way each Each Excess(+) Full Conversion INR

XLPE INSULATED UN-ARMOURED CABLES (LOOSE):- Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:- Excess(+) Full Conversion INR

Overall size 10sq.mm (2Core) Un-armoured (Loose) Mtr. Excess(+) Full Conversion INR

Overall size 25sq.mm (3½ Core) Un-armoured (Loose) Mtr. Excess(+) Full Conversion INR

DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES: Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:- Excess(+) Full Conversion INR

Double walled corrugated (DWC) HDPE pipe 63/51 mm (outer/ inner dia.) mtr. Excess(+) Full Conversion INR

MCCB's (MOULDED CASE CIRCUIT BREAKER): Supply and erection of Moulded Case Circuit Breaker (Panel mounting Cubical type) in the existing Cubical Panel (confirm to IEC:60947-2) having Ics=100% Icu, 100% neutral with spreader links and relevant PWD general specifications complete with G.I. Bolts, Nuts & Connection on both sides of MCCB with suitable size of thimbles etc:- Excess(+) Full Conversion INR

MCCB Four Pole 63/80/100amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting Each Excess(+) Full Conversion INR

MS SHEET ENCLOSURE FOR MCCB's: Supply & Erection of indoor type MCCB enclosure of suitable size having provision for MCCB with extended rotary handle. The Enclosure shall be made from 14/16 SWG CRCA sheet, confirming to IS 8623/1977-82. The door should be double folded without edge and the gasket should be ‘S’ type puffed neutral rubber gasket for long life. The hinges of the door should be bolted type with double hole arrangement. The Enclosure door lock should be quick openable type spring loaded. There should not be any special tool or key to open the lock. The Enclosure will be wall mounting type having provision for cable entry from bottom/top with cable glands etc. The sheet metal is sprayed with corrosion resistant etch primer. The finishing treatment shall be applicable with air drying paint (7/9 tank Powder coated process should present in company pemises) after necessary putty work:- Excess(+) Full Conversion INR

MS Sheet Enclosure having provision for MCCB 40-160Amp.with extended rotary handle (Approx. Size 500mm x 300mm x 200mm) Each Excess(+) Full Conversion INR

SHEET METAL IRON CLAD CHANGEOVER SWITCHES: Supply and erection of sheet metal Iron Clad Changeover Switch on existing surface with G.I. bolts & nuts/rag bolts and nuts etc., according to the size of holes in the body of the switch including connections with suitable size of thimbles and bonding to the existing earth as per PWD General Specifications:- Excess(+) Full Conversion INR

IC Four Pole Changeover Switch 32amp., 415volts Each Excess(+) Full Conversion INR

GI PIPE POLES & BRACKETS: Excess(+) Full Conversion INR

Supply and erection of G.I. Pipe 40mm dia. (A-class) Single arm bracket of suitable length give a total overhang at a tentative angle of 100/105º, the bracket should be fixed on the top of the GI pipe pole having top outer dia. 80mm/100mm with GI reducer of suitable size with two coats of an approved aluminium paint complete in all respect as approved by the Engineer-in-charge at site:- Excess(+) Full Conversion INR

Single Arm Bracket 1 metre Long with G.I. Reducer 80mm x 40mm Each Excess(+) Full Conversion INR

Supply and erection of LED batten 20 Watt LED (including constant LED driver) with High quality extruded aluminium with efficacy of LED fixture minimunm 100 lumens per watt and operating voltage between 140 to 270 volt, THD <10% ingress protection IP20 (as per latest BIS standards) surge protection - 2.5 KV and above (as per IS/ IEC standards) wattage of each low power LED less than 1 watt input AC frequency 50 Hz ± 3 % with 5 year warranty including their drivers complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter ION No:- AT/2021/GL/1410-1422 Dated:- 06.05.2021. Besides this the lighting fixtures manufactures should have in house NABL accredited labortary. Each Excess(+) Full Conversion INR

Supply and erection of LED batten 40 Watt LED (including constant LED driver) with High quality extruded aluminium with efficacy of LED fixture minimunm 100 lumens per watt and operating voltage between 140 to 270 volt, THD <10% ingress protection IP20 (as per latest BIS standards) surge protection - 2.5 KV and above (as per IS/ IEC standards) wattage of each low power LED less than 1 watt input AC frequency 50 Hz ± 3 % with 5 year warranty including their drivers complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter ION No:- AT/2021/GL/1410-1422 Dated:- 06.05.2021. Besides this the lighting fixtures manufactures should have in house NABL accredited labortary. Each Excess(+) Full Conversion INR

Supply and erection of Heavy duty Exhust Fans 300mm sweep 900RPM complete with aluminium louver shutter double ball bearing, longer life including flexible wire & petty material etc. for connections and testing complete in all respect as approved and desired by the Engineer in-charges at site. Each Excess(+) Full Conversion INR

Supply and erection of Slim Recessed mounted, Round downlighter 18 watt, Supply Voltage 140-270Volts AC supply, 50Hz ± 3% (including BIS Certified potted single diver with screen or laser printing logo LED driver) with CRCA sheet with control gear (IP 20 protection), THD<10%, CRI minimum 70, Low power LED with wattage Less 1 Watt, Surge Protection 2.5KV and above as per IS/ IEC Standards, efficacy of LED fixture minimum 100 lumens per watt, 5 year warranty including their drivers complete in all respects as approved and desired by the Engineer in-charge at site. LED Fittings as per specifications approved by Hon'ble Technical Advisor to Punjab Govt. vide Letter ION No:- AT/2021/GL/1410-1422 Dated:- 06.05.2021. Besides this the lighting fixtures manufacturers should have in house NABL accredited lab. Each Excess(+) Full Conversion INR

Supply and erection of Recessed Mounted 36 Watt LED 2x2 panel (including constant LED driver) with CRCA sheet having efficacy of LED fixture minimunm 100 lumens per watt and operating voltage between 140 to 270 volt, THD <10% ingress protection IP20 (as per latest BIS standards) surge protection - 2.5 KV and above (as per IS/IEC standards) wattage of each low power LED less than 1 watt input AC frequency 50 Hz ± 3 % with 5 year warranty including there drivers complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter ION No:- AT/2021/GL/1410-1422 Dated:- 06.05.2021. Besides this the lighting fixtures manufactures should have in house NABL accredited labortary. Each Excess(+) Full Conversion INR

Supply and erection of Surface Mounted 36 Watt LED 2x2 panel (including constant LED driver) with High quality extruded aluminium with efficacy of LED fixture minimunm 100 lumens per watt and operating voltage between 140 to 270 volt, THD <10% ingress protection IP20 (as per latest BIS standards) serge protection - 2.5 KV and above (as per IS/IEC standards) wattage of each low power LED less than 1 watt input AC frequency 50 Hz ± 3 % with 5 year warranty including there drivers complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter ION No:- AT/2021/GL/1410-1422 Dated:- 06.05.2021. Besides this the lighting fixtures manufactures should have in house NABL accredited labortary. Each Excess(+) Full Conversion INR

Supply and erection of Wall Fan Plastic Body 400MM, 16" including flexible wire & petty material etc. for connections and testing complete in all respect as approved and desired by the Engineer in-charges at site. Each Excess(+) Full Conversion INR

Supply and erection of LED Street Light 45watt, Supply Voltage 140-270Volts AC supply, 50Hz ± 3% (including BIS Certified potted single diver with screen or laser printing logo LED driver) with pressure die cast or extruded aluminium housing with control gear (IP 66 protection), THD<10%, CRI minimum 70, High power LED (with wattage 1 to 5 Watt) with mandatory secondary lenses, toughened glass fitting, 4 KV SPD within driver and 10KV external SPD, Min IK07, efficacy of LED fixture minimum 120 lumens per watt, 5 year warranty including their drivers complete in all respects as approved and desired by the Engineer in-charge at site. LED Fittings as per specifications approved by Hon'ble Technical Advisor to Punjab Govt. vide Letter ION No:- AT/2021/GL/1410-1422 Dated:- 06.05.2021. Besides this the lighting fixtures manufacturers should have in house NABL accredited lab. Each Excess(+) Full Conversion INR

Supply and erection of 3-Star rating AC Ceiling Fan 1200mm (48") suitable for 230 V single phase with double ball bearing, copper wound, full aluminium body, 3Nos. of blades, white in colour. The mounting type is down rod mount. The product should possess a minimum air deleivery of 218 CMM. The rated speed of the the product must be minimum of 350 revolutions per minute and 5Nos. of speeds. The approximate weight of the product should be 4Kg and 180gms.(without packing) or higher. The product should have a manufcaturer's guarantee /warranty of minimum 2 years. The product should be complete in all aspects with fan motor, bladeset, down rod, conopy set, shackle kit, twisted wire etc., including erection & testing of ceiling fan having connection with PVC insulated PVC sheathed two single core copper conductor (FR) cable 0.75 sq. mm complete in all respects as per satisfcation of the Engineer in-charge at site. Each Excess(+) Full Conversion INR

Supply & Installation of 12V. 150AH tubular battery including connection & testing charges etc. Complete in all respect as per entire satisfaction of the Engineer In Charge. Each Excess(+) Full Conversion INR

Supply & Installation of Stand for Inverter & 2 No. Batteries including connection & testing charges etc. Complete in all respect as per entire satisfaction of the Engineer In Charge. Each Excess(+) Full Conversion INR

Supply & Installation of 2KVA Sinewave Inverter including connection & testing charges etc. Complete in all respect as per entire satisfaction of the Engineer In Charge. Each Excess(+) Full Conversion INR

Networking Excess(+) Full Conversion INR

Supply, installation Testing and commissioning of 8 port Switch 10/100/1000. Complete in all respect as desired by the engineer in charge at site Nos Excess(+) Full Conversion INR

Supply, installation Testing and commissioning of 1 KVA UPS with input power factor -0.09, Output power factor - 0.8 OVCD inbuilt DC V 24v Efficiency: Above 90 %, Voltage range 140-300v AC, Frequency 50HZ +/-10%, Voltage 230 AC nominal, frequency (battery mode) 50HZ +/- 1HZ, transfer time 4-8 ms, Voltage mains AVR mode 230V AC normal, rating 1100VA, Type sealed lead acid 12V,7.2 Ahx2, Recharge time- 4-6 Hrs, Complete in all respect as desired by the engineer in change at site. Nos Excess(+) Full Conversion INR

S/I/T/C of intercom facility 1+1 Basic Plan Phone Ringer volume control switch Tone/ Pulse Switchable Redial Mute Flash Pause Intercom facility Call T, Holding the line / Music on Hold during call transfer Line use LED Indication, Secrecy during conversation between both phones, including connecting cables Nos Excess(+) Full Conversion INR

Supply Installation Testing and Commissioning of Token display system with micro controller based technology with display size 15”x6” height of 3-digit display is 4” in mild steel enclosure with acrylic front cover complete in all respect as desired by the engineer-Incharge Nos Excess(+) Full Conversion INR

Supply, installation Testing and commissioning of Wall Mount 6U x 450 W x 500 D. Front Glass Door ((tinted Toughened) with Lock & Key, 2 pairs of 19" Mounting Rails with U-Marking. Welded Side Walls, Min Accessories 1U Cable Manager (1). Hardware Packet (1 Pkt), 6 Socket 5 Amp Power Distribution Unit (1 No), Roof Mounted Fan Unit / 90 CFM /230V AC. as per DIN 41494. Complete in all respect as desired by the Engineer in change at site Nos Excess(+) Full Conversion INR

Supply and erection of telephone cable with solid bare copper conductor, special grade PE insulation, paired, polyster taped, nylon rip cord, FR PVC sheathed, conforming to TEC Specification No. G/WIR-06/03 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- Excess(+) Full Conversion INR

Telephone Cable 0.5 Sq.mm, 2 Pair mtr. Excess(+) Full Conversion INR

PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- Excess(+) Full Conversion INR

Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) Flushed mtr. Excess(+) Full Conversion INR

Heavy gauge PVC conduit pipe 40mm dia. (ISI marked) Flushed mtr. Excess(+) Full Conversion INR

Supply and erection of CAT 6 with 23AWG solid bare copper conductor, special grade PE insulation with star separator, 4pair Unshielded Twisted Pair (UTP) industrial cable, FR PVC sheathed, Class-E, 250 MHz of bandwidth, supporting data transfer speeds of up to 10 Gbps (10GBASE-T) for distances up to approximately 180 feet, cables are manufactured and tested to meet the ANSI/TIA 568-C.2 and ISO/IEC 11801 Class E standards left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- Excess(+) Full Conversion INR

CAT 6 LAN cable mtr. Excess(+) Full Conversion INR

Public Health Services Excess(+) Full Conversion INR

Sub Head-1 Internal Sewerage System Excess(+) Full Conversion INR

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. Single Socket Type B Excess(+) Full Conversion INR

110mm o/d SWR UPVC pipe lines laid complete mtr Excess(+) Full Conversion INR

90mm o/d SWR UPVC pipe lines laid complete mtr Excess(+) Full Conversion INR

Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. Excess(+) Full Conversion INR

For 110mm o/d pipes Excess(+) Full Conversion INR

Door Cap Nos Excess(+) Full Conversion INR

Door Elbow 90 Degree (All side socketed) Nos Excess(+) Full Conversion INR

Elbow 90 Degree (All side socketed) Nos Excess(+) Full Conversion INR

Vent Cowls Nos Excess(+) Full Conversion INR

Coupler Nos Excess(+) Full Conversion INR

P Trap / Floor Trap 110 mm x75 mm Nos Excess(+) Full Conversion INR

Single Tee With Door Nos Excess(+) Full Conversion INR

For 90mm o/d pipes Excess(+) Full Conversion INR

Door elbow 90 degree (all side socket) (Description Changed) Nos Excess(+) Full Conversion INR

Elbow 90 degree (all side socket) Nos Excess(+) Full Conversion INR

Vent Cowls Nos Excess(+) Full Conversion INR

Coupler Nos Excess(+) Full Conversion INR

Single Tee With Door Nos Excess(+) Full Conversion INR

Providing PVC solvent cement joints to SWR Pipes and specials including cost of PVC solvent cement and tools etc of approved make (to the approval of Engineer-in-charge) Excess(+) Full Conversion INR

110mm o/d nos Excess(+) Full Conversion INR

90mm o/d nos Excess(+) Full Conversion INR

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm. Excess(+) Full Conversion INR

100mm internal Diametre S.W.gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm Nos Excess(+) Full Conversion INR

Construction of brick masonry inspection chambers size as given below upto 0.60 metre average depth in 1:5 cement sand mortar, C.C.1:4:8 ( 150mm thick) in foundation, cement concrete 1:2:4 benching 12.50mm thick cement plaster 1:2 with a floating coat of 1mm thick of neat cement, R.C.C. 1:2:4 slabs 100mm thick cement concrete topping 50mm thick with 455mm x 455mm, 455mm x 610mm inside R.C.C. inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design. Excess(+) Full Conversion INR

450mm x 600mm inside with 455mm x 610mm cover and frame light duty double seal Nos Excess(+) Full Conversion INR

Sub Head-2 Internal Water Supply System Excess(+) Full Conversion INR

CONCEALED IN WALL: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-in- Charge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings, with one step CPVC solvent cement and testing of pipes complete as per direction of Engineer-in-Charge. Excess(+) Full Conversion INR

CPVC SDR 11 Pipe & fitting 16mm o/d mtr Excess(+) Full Conversion INR

SDR 11 CPVC pipes & fittings 20mm o/d mtr Excess(+) Full Conversion INR

CPVC SDR 11 Pipe & fitting 25mm o/d mtr Excess(+) Full Conversion INR

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes lines and making good the same to its original condition. Size 75mm x 75mm Excess(+) Full Conversion INR

20 & 25 mm pipe in wall mtr Excess(+) Full Conversion INR

Cutting holes upto 23cm square through B.B. in cement walls or stone masonary wall in cement for pipes, and making good the same & finishing according to existing finish where required. Excess(+) Full Conversion INR

Through wall 11.43 cm thick Detail as per Table-2 nos Excess(+) Full Conversion INR

Through wall 22.86 cm thick Detail as per Table-2 nos Excess(+) Full Conversion INR

Providing, fixing and jointing Cpvc Union Couplings with Upvc Pipes complete in all respect. Excess(+) Full Conversion INR

40mm i/d Cpvc Union Each Excess(+) Full Conversion INR

Sub Head - 3 Sanitary Installation Excess(+) Full Conversion INR

Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern ISI marked, PVC short bend 32 mm dia including cost of seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge. Detail attached as per Table-3 Nos Excess(+) Full Conversion INR

Providing and fixing in position Chinaware Floor Mounted One Piece EWC type with matching chinaware cistern 10 ltr. Capacity. (without cistern fitting) with P trap or S trap of approved make (to the approval of the Engineer-in-charge) and seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge. Excess(+) Full Conversion INR

Chinaware Floor Mounted One Piece EWC rim less type with matching chinaware cistern 10 ltr. Capacity. (without cistern fitting) size 69x36x74 cm with P trap or S trap and seat cover complete in all respect. Nos Excess(+) Full Conversion INR

Providing and fixing PVC accessory fittings in Chinaware flushing cistern 10 Litres capacity complete. Nos Excess(+) Full Conversion INR

Providing and fixing in position Metropole flush valve push type 32mm size dual flow (Concealed body) with exposed shut off provision and round plate complete in all respect. Nos Excess(+) Full Conversion INR

Providing and fixing jet spray with 2'-6" long PVC pipe.With PTMT nut Detail attached as per Table-3 Nos Excess(+) Full Conversion INR

Providing & Fixing in position C.P. Brass Hexa Nipple 15mm of approved make (to the approval of Engineer-in-charge ) complete in all respect. Detail attached as per Table-3 Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing and fixing in position vitreous Chinaware white lIndian make large flat back or angular lipped front urinal 375 x 390 x 590 mm of approved make (to the approval of the Engineer-in-charge) consisting of C.P. brass Urinal waste Coupling dome type 32mm outer length 75 mm , C.P. brass Urinal Spreader Ocular-Regular and C.P. brass tube connection 300 mm long complete. Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing and fixing partition for different type of urinals. A) 19 to 20 mm thick Granite stone partition ii) size 375mm x 750mm nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in all respect. Excess(+) Full Conversion INR

Size 550 mm x 400 mm x 815mm Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing and fixing vitreous chinaware standard pedestal of approved make (to the approval of Engineer-in-charge) for wash hand basin complete in all respect. Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respect. PVC tube connection of size 15 mm x 450 mm with PTMT nut nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing and fixing P.V.C Waste Pipe Collapsible 32mm complete in all respect. nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing and fixing in position towel rails / ring of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs embedded in walls with brass screws complete in all respect. Excess(+) Full Conversion INR

C.P. brass towel Ring Nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing and fixing in position paper holders of approved make (to the approval of Engineer-in-charge ) fixed in to wall with C.P brass screws complete in all respect. C.P. brass toilet paper holder Nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing and fixing in position C.P. brass soap dish of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect. Nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing & Fixing in postion 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge )complete in all respect. Excess(+) Full Conversion INR

C.P Brass bib cock foam flow without flange Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing & Fixing in postion stop cock / Angle valve of approved make (to the approval of Engineer-in-charge ) complete in all respect. Excess(+) Full Conversion INR

C.P.brass 15mm Angle valve without flange Nos "`"\ #,##0.00 Excess(+) Full Conversion INR

C.P.brass 15mm Concealed stop cock with flange Nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing & Fixing in position C.P. Brass flange Dome of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect. each "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing & Fixing in position C.P. Brass extension piece 25mm long to 100mm long of approved make (to the approval of Engineer-incharge )with various fixtures complete in all respect. C.P. Brass extension piece, 25mm long to 50mm long each "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on top complete in all respect (as required by the Engineer-in- Charge) (Size 600mm x 450mm) Nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing & fixing in postion C.P. brass Sink Cock swinging casted spout (table mounted) of approved make (to the approval of Engineer- in-charge) complete in all respect. Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing & Fixing in position C.P./Aluminium Khunti of approved make (to the approval of Engineer-in-charge ) fixed into wall with C.P. brass screws and rawl plugs etc. complete in all respect. C.P. Brass khunti with 3 pegs Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing and fixing in position SS Grating with frame of approved make (to the approval of engineer in charge) complete in all respects. Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing and fixing in position stainless steel sinks of approved make (to the approval of Engineer-in-charge) 1mm thick,grade-304 (18/8) with waste coupling complete in all respect. a) Rectangular Sink with Deluxe Border Single Bowl Overall Size 700 mm x 555 mm x 230 mm Nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank. Tripple Layer Tanks ltr "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing and fixing in position automatic brass Ball Cock in tanks. Plastic Ball Cock with rod and Plastic Ball Excess(+) Full Conversion INR

40 mm i/d Nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing and fixing in position cPVC. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect. Excess(+) Full Conversion INR

CPVC tank nipple 25mm i/d Nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing, fixing and jointing ISI Marked Gun- Metal peet valves (Heavy Pattern) as per IS 778 with hand wheels, on G.I. Pipe lines laid in the ground or inside buildings including all carriages complete. Excess(+) Full Conversion INR

25mm i/d cpvc peet valve heav ypattern. Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Construction of Plateform complete as per specification & as desired by Enginer-in-charge Excess(+) Full Conversion INR

For 1000 ltr Water Tank Nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing & Installation of SS table for Sample collection Room of Top size 6'-6"x2'-0"x 2'-9" high having provision of lab sink complete as per drawing & specifications as desired by Engineer-in-Charge kg "`"\ #,##0.00 Excess(+) Full Conversion INR

Sub Head-4 Flooring and Wall Tile Excess(+) Full Conversion INR

Base course of floor consisting of 100mm thick cement concrete 1:8:16 with stone aggregate 40mm guage and 100mm fine sand filling using mechanical mixer for mixing of material sqm "`"\ #,##0.00 Excess(+) Full Conversion INR

Cement concrete 1:2:4 With stone ballast or shingle mixing by mechanical means using concrete mixer volumetric type CUM "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., completewhite cement slurry in joints including corners angles and beading. sqm "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 600 x 300 mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. sqm "`"\ #,##0.00 Excess(+) Full Conversion INR

Sub Head -5 Drinking Water Coller & Air Conditioning System Excess(+) Full Conversion INR

Providing & fixing in position Water Cooler without Stablizer of approved make (to the approval of Engineer-in-charge ) including carriage complete in all respect. Excess(+) Full Conversion INR

Water Cooler Full Steel Body 40/80 ltr without Stablizer nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Supply and erection of Single phase copper wound Automatic voltage stablizer of suitable capacity electronically controlled circuit with input voltage 140-260 volts single phase AC supply and output voltage 220 ± 5% volts single phase AC supply having main silicon core copper wound step up transformer with suitable nos. of turns on primary side and secondary side the transformer should be fully insulated inside the MS sheet box of suitable size. There should be power control relay and single pole MCB (C-curve, 10kA) of suitable capacity complete with internal copper wiring along with amp. meter and volt meter, high voltage cut off 280 volt input (240 volt output) and 90 volt maximum boost and overloading protection to be provided:- i) Automatic Voltage Stablizer 2 KVA Each "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing & fixing in position UV filter having flow rate 200 ltr/hr with 3 stage purification process having 16 watt UV lamp and 35 Watt power rating of approved make (to the approval of Engineer-in-charge ) including carriage and fixing in position complete in all respect. Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing & installing & erection split type wall mounted air conditioner capacity 1.0 TR Rating Three star fixed speed confirming to IS: 1391 (Part-2) -1992 with amendments no. 1&2 fitted with Rotary compressor operating on Refrigerent R-32 reputed make:-Carrier, Toshiba, Mitsubishi Electric, Daikin, O General, Hitachi, or equivalent with 4.00 KVA voltage stabilizer With Copper Winding With range of 130 to 280 Volt of Reputed make, Bluebird, Packard,Logicstate etc. MCB arrangement for installing OD units on terrace including inlet and outlet copper tubes with proper insulation drainage arrangement cable link between ID unit and OD units stand for OD unit and connection of concealing of Copper pipes and drainage pipes within building, including stand, installing charges, GST& Contractor Profit complete in all respects. Excess(+) Full Conversion INR

1.0 TR Capacity (As per Detail) Each "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing & installing & erection split type wall mounted air conditioner capacity 1.5 TR Rating Three star fixed speed confirming to IS: 1391 (Part-2) -1992 with amendments no. 1&2 fitted with Rotary compressor operating on Refrigerent R-32 reputed make:-Carrier, Toshiba, Mitsubishi Electric, Daikin, O General, Hitachi, or equivalent with 4.00 KVA voltage stabilizer With Copper Winding With range of 130 to 280 Volt of Reputed make, Bluebird, Packard,Logicstate etc. MCB arrangement for installing OD units on terrace including inlet and outlet copper tubes with proper insulation drainage arrangement cable link between ID unit and OD units stand for OD unit and connection of concealing of Copper pipes and drainage pipes within building, including stand, installing charges, GST& Contractor Profit complete in all respects. Excess(+) Full Conversion INR

1.5 TR Capacity (As per Detail) Each "`"\ #,##0.00 Excess(+) Full Conversion INR

SubWork - 2 Excess(+) Full Conversion INR

Sub Head-1 Estate Water Supply Excess(+) Full Conversion INR

Excavation by mechanical means(JCB or Hydraulic excavator) in trenches for pipe lines with straight or open cutting in streets or open area including trimming and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation,watering , including the cost of dewatering of rain water, diversion for traffic, night signals. providing & fixing caution boards, crossing over trenches for access to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the town involving lead upto 15 meter complete in all respect. Excess(+) Full Conversion INR

Earth work upto 1.5 m. Depth All classes of soil except rocky cum "`"\ #,##0.00 Excess(+) Full Conversion INR

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes lines and making good the same to its original condition. Size 75mm x 75mm Excess(+) Full Conversion INR

40 mm pipe in wall (for 2 Connection mtr "`"\ #,##0.99 Excess(+) Full Conversion INR

EXTERNAL IN THE GROUND : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-in-Charge), having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, & testing of joints excluding cost of excavation complete as per direction of Engineer-in-Charge. Excess(+) Full Conversion INR

CPVC SDR 11 pipe & fittings 40 mm o/d (For 1000 ltr tank No. 1+ Tank No. 2) mtr "`"\ #,##0.99 Excess(+) Full Conversion INR

CPVC SDR 11 pipe & fittings 25mm o/d (For 500 ltr tank No. 1 to Tank No. 2) mtr "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing, fixing and jointing Cpvc Union Couplings with Upvc Pipes complete in all respect. Excess(+) Full Conversion INR

25mm i/d Cpvc. Union Each "`"\ #,##0.00 Excess(+) Full Conversion INR

Provision for 110mm PVC boreing up to 70 mtr deep, installing, lowering, commissioning of 2 BHP Submercible pumping set including Starter, all fitting etc. complete in all respects. (ISI Marked Make Lubi, crompton, KSB, Kirloskar) Nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Sub Work-3 Excess(+) Full Conversion INR

Sub Head-1 Estate Sewerage Excess(+) Full Conversion INR

Providing, laying in trenches to correct gradient and alignment and jointing of UPVC pipes having ISI specification IS:15328-2003 class-SN-8 marked make Supreme, Finolex, Kissan, Jain, Prince or equivalent good on them and laying the same in trenches to correct alignment and gradients, cutting and jointing, testing for water tightness and making good the leakages and defects including cost of specials (Specials and Solvent should be of same make as that of pipes) complete in all respects. Excess(+) Full Conversion INR

110 mm o/d pipes mtr. "`"\ #,##0.00 Excess(+) Full Conversion INR

160 mm o/d pipes mtr. "`"\ #,##0.00 Excess(+) Full Conversion INR

Excavation in trenches with straight or open cutting in streets, lanes or in open area with 3D/JCB or excavator including manually dressing bed, trimming sides and side slopes for sewers and manholes to full depths as shown in drawings,including, dressing to correct sections and dewatering, provision for diversion for traffic, protection of existing services i.e. telephone cables, electric lines, water supply lines and gas lines etc. night signals, profiles, pegs, sight rails, boning rods, watching, etc., fixing and maintenance of caution boards, fencing, refilling trenches, watering, ramming and restoration of surface to original level and removal of surplus spoil from the site of works, upto one chain (15m) complete in all respects. Excess(+) Full Conversion INR

For depth exceeding 3.0 m but not exceeding 4.5 m B.G.L. For all classes of soil except rocky cum "`"\ #,##0.00 Excess(+) Full Conversion INR

Providing and filling sand grading as per specifications or fine grade around the various sizes of G.I. pipes in external work. cum "`"\ #,##0.00 Excess(+) Full Conversion INR

Making soak pit 2.5 m outer Diametre 3.0 metre deep 230mm thick 1:5 brick work honey comb with bricks of Ist Class and S.W. drain pipe 100 mm Diametre, 1.8 m long complete as per standard design. Excess(+) Full Conversion INR

With F.P.S. bricks nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Provision for construction of New Septic Tank complete. nos "`"\ #,##0.00 Excess(+) Full Conversion INR

Sub Work-4 Excess(+) Full Conversion INR

Fire Fighting Arrangements Excess(+) Full Conversion INR

Providing and fixing of FIRE EXTINGUISHER CO2 type as per IS:15683 complete with all accessories as per manufactures sepcification. ISI Mark Complete in all respect. 4.5kg capacity Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing and fixing of FIRE EXTINGUISHER ABC powder type (Stored pressure) as per IS:15683 complete with all accessories as per manufactures sepcification. ISI Mark Complete in all respect. 4 Kg. Capacity Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Providing and fixing of FIRE EXTINGUISHER, Mechanical Foam Type 9 ltr IS: 15683 Stored Pressure type complete with all accessories as per Manufactures Specification. ISI Mark of approved make complete in all respect. Nos "`"\ #,##0.99 Excess(+) Full Conversion INR

Total in Figures

Quoted Rate in Figures Select

Please Enable Macros to View BoQ information