SPECIAL REPAIR OF JCO OR MD ACCN P-21 11 QTRS AND CIVIL MD ACCN P-45 05 QTRS, P-46 11 QTRS, P-87 ,2 QTRS AND P-84 GARAGE AND OR MD ACCN P-25 08 QTRS, P-26 08 QTRS AND P-27 03 QTRS AT AHRR UNDER GE EM RR HOSP, DELHI CANTT-10

Amount

Demolition of brick work or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified.

M&L for brick work with sub class 'B' Bricks straight or curved on plan exc 6m mean radius, built in CM 1:6, complete all as specified and as directed.

M&L for brick work with sub- class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster on walls and ceiling of any description including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed.

M&L for 15mm thick rendering on brick or concrete wall surfaces in cement mortar 1:6, finished the surface even and fair without using extra cemnent, complete all as specified and as directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers i.e.. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) mixed with WPC finished even and fair etc complete all as specified and directed. (Note:- WPC shall be measured and paid separately.)

M&L for 5mm thick rendering on concrete ceiling surfaces in cement mortar 1:3, finished the surface even and fair without using extra cemnent, complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceilings and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying 1-2mm thick cement base wall care putty exterior grade on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of acrylic smooth exterior paint of required shade over one coat priming of exterior primer complete all as specified and directed.

M&L for complete removal of existing treatment from internal surfaces of walls by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed.

M&L for complete removal of existing treatment from internal surfaces of ceiling by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed.

M&L for complete removal of existing treatment from from external surfaces of walls by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty exterior grade on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of acrylic smooth exterior paint of required shade over a coat of exterior grade primer complete all as specified and directed. Note for item No 8 to 13: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of these items.

Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing) and rubbish off the premises, complete all as specified & directed.

M&L for Glazed ceramic tile 8 to 10 mm thick (square/ rectangular) of light shade, area of each tile not exceeding 0.36 Sqm, as in floor etc, set & jointed in neat cement slurry and pointed in white/ colour cement to match over & including 15mm thick screed bed or bedding layer in CM 1:4 for laying floor finishes, complete all as specified and directed.

M&L for Glazed ceramic tile 8 to 10mm thick (square/ rectangular) of light shade, area of each tile not exceeding 0.36 Sqm, as in dado/skirting etc, set & jointed in neat cement slurry and pointed in white/ colour cement to match over & including 10mm thick rendering in CM 1:3 as a backing coat on walls for fixing of tiles complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick of size 300mmx300mm as in floors etc, set and jointed in near cement slurry and pointed in white or colour cement to match over & including 15mm thick screed bed or bedding layer in CM 1:4 for laying floor finishes, complete all as specified and directed.

M&L for glazed ceramic coloured wall tiles of size 600mm x 300mm, 7mm to 8mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering on fair faces of brick work on concrete surface in cement mortar 1:3 for backing coat complete all as specified.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, complete all as specified.

M&L for cement concrete 1:5:10, type E2 (using 40mm graded aggregate), as in sunken flooring, complete all as specified and directed.

M&L for rendering 15mm thick cement screed in CM 1:4 on brick or concrete surfaces using integral water proofing (3% by weight) for floor and sides of wall, complete all as specified and directed.

Supply only liquid water proofing compound, complete all as specified.

M&L for sealing of pipe peneration toilets core cutting & sunken slab treatment in following stages:- supply and apply solvent free, moisture intensive epoxy resin based patch repair putty Sikagrade-694F (I), yeild : 0.6 Ltr/kg suitable for submerged condition having compressive strength of 40 N/mm2 (1 day) according to IS 9162-1979 on pipe peneration surface. The putty shall be appllied to a groove thickness of minimum 20mm on pipe peneration joints to concrete etration of surface of sunken portion and M&L for glass fibre reinforced acrylic modified cementtitious coating system as Top cost : Sika Top Seal - 107 @ 1.5 kg/sqm over reinforcement : Sika Fab-1 over base coat : Sika Top Seal-107 1.5 kg/sqm etc all as specified and directed system should have compressive strength 20 N/mm2, Bond strength 2.0 N/mm2 including providing 40mm bore GI pipe spout pipe, complete all as specified and directed. Note: (a) Entire work shall be carried out through manufacturer or its authorised representive. (b) The contractor shall furnish a 10 years guarantee for effectiveness of water proofing.

M&L for 25mm thick PCC 1:2:4 type B1 (using 20mm graded stoe aggregate) as in sub base to floor tiles, complete all as specified.

Demolition of stone slabs or tiles of any description or thickness in any position laid, bedded and pointed in any mortar, complete all as specified & directed.

M&L for 18 to 20mm thick granite (of any type) tiles as in flooring, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete, over & including 15mm thick screed bed or bedding layer in cement mortar (1:4) for laying floor finishes, complete all as specified & directed. Note: - (a) "Minimum rate of granite should not be less than Rs.150 Per Sqft excluding GST”

M&L machine cut kota stone slab flooring 20 to 25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including screed bed and bedding layer of 15 mm thick in CM 1:4, complete all as specified.

M&L machine cut kota stone slab flooring 20 to 25mm thick riser of steps with single piece. Skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 10mm thick rendering in CM 1:3 as a backing coat complete all as specified and directed.

M&L for 18-20mm thick marble makrana green machine cut in floor, landing etc and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 15mm thick screed bed or bedding layer in CM 1:6, complete all as specified and directed.

M&L for 18-20mm thick marble makrana green machine cut in skirting/ dado, riser of steps with single piece laid over cement screed bed of bedding and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 10mm thick rendering in CM 1:4 as a backing coat on walls for fixing of tiles complete all as specified and directed.

Providing edge moulding to 18-20mm thick granite/marble stones of any description of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed.

Taking down chowkats or frames including shutter (without taking off shutters from the frame) area not exc 1.50 Sqm each, complete all as specified and directed.

Taking down chowkats or frames including shutter (without taking off shutters from the frame) area exc 1.50 Sqm but n.exc 4.00 sqm each, complete all as specified and directed.

S&F factory made solid WPC (wood polymer composite) door frame 125mmx65mm double rebated made from WPC (single extruded process) material comprisin of virgin PVC polymer of K value 57-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk / weat husk) and non toxic additives fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 780 kg/cum, having good screw holding capacity (screw withdrawl strength of min 990 N), min compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixing in position with SS Dsh fasteners/ hold fast of required dia and length, complete all as specified and directed

S&F factory made single extruded WPC (wood polymer composite) solid door frame of size 100mmx65mm comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fiber (wood powder/ rice husk/ wheat husk) and non toxic additives (max toxicity index of 12 for 100gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750 kg/cum, screw withdrawl strength of 2200 N (face) 1100n (edge) min compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant, complete all as specified and directed

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed. (Note: stainless steel butt hinges shall be paid separately)

S&F Providing 35mm thick FACTORY MADE B/S PRELAM WIRE MESH SOLID PVC DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15mm x 15mm for top, lock & bottom rails. M.S. frame shall have a coat of metal primer of approved make and manufacturer. 19mm x 19mm M.S. square tubes shall be covered with heat moulded Prelam sheet 'C' channel made from 5mm (±0.25) thick PVC Sheet of Density 600 Kg /Cum Manufactured by an ISO-9001-2015 certified Company, of size 35mm thickness, 115mm width out of which 100mm shall be flat and 15mm shall be bent in 90° angle on either side forming stiles,one of the 90° bend edge is cut from stiles as well as rails to nail from inner side of door to hide wire mesh fixing steel screws. 5mm (±0.25) thick 140mm wide PVC sheet out of which 125mm shall be flat and 15mm shall be bent in 90° on the inner side to form top and bottom rail and 155 mm wide PVC sheet out of which 100 mm shall be flat and 15mm shall be bent in 90° on both side to form lock rail. An additional 5mm (±0.25) thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent cement adhesive. Panel will be of GI /SS wire mesh of 24 gauge to be fitted inside area of stiles & rails. The wire mesh in top, bottom & lock rail is sealed with 15mm x15mm tube with steel screw of size 13/6 mm.10mm (5mm x 2nos) thick PVC strip of 25mm width is to be stuck & nails on both side of G.I. wire mesh interior at the top, bottom & lock rail. 10mm thick (5mm x 2nos) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardware’s should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings.

S&F factory made single extruded WPC (wood polymer composite) soild plain flush door shutter of 30mm thick comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fibers (wood powder/ rice husk / weat husk) and non toxic additives (max toxicity index of 12 for 100gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750 kg/cum, screw withdrawl strength of 2200 N (face) 1100N (edge) min compressive strength of 58 N/mm2, modulus of elasticity 900 N/MM2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed countersunk SS screw, complete all as specified and directed

S&F 150mm long stainless steel barrel tower bolts, complete as specified and directed

S&F 200mm long stainless steel barrel tower bolts, complete as specified and directed

S&F 150mm size stainless steel handles, complete all as specified and directed

S&F 250mm long stainless steel sliding door bolt with staple (bolt type) and fixing clips and fixing bolts and sliding bolts, complete all as specified and directed

S&F butt hinges, stainless steel 100mm size, complete all as specified and directed

S&F 140mm floor door stopper of stainless steel body and tongue with hard drawn steel spring fixed in floor, complete all as specified and directed

S&F aluminium window as per TD drg No. CEDZ/TD-316 with following specifications :- (i) Outer frame of size 40mmx114mm with 1.3mm thickness, corner 45 degree cut & aluminium welded. (ii) Center mullion of size 40mmx65mm. (iii) Welded shutter (02 Nos) of size 40mmx60mmx1.3mm thickness 45 degree cut mechanically joint with 6mm allen key bolt clamp with 5mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock, aluminium kobra hinges 2 Nos per shutter. (iv) 12mm SS 202 grade round bar safety grill at 100mm cc distance modified to 150mm cc distance in front of handle, welded at both ends with 6mm SS 202 grade round bar. (v) Welded wiremesh shutter (2 Nos) of size 40mmx18mmx1.3mm thickness 45 degree cut with 0.45mm nominal dia of SS wire mesh, SS 75mm long hinges & PVC magnet. (vi) Entire window shall be powder coated with pure polyster coat of any shade as approved by GE. (vii) Window shall be installed with silicone complete all as specified and directed.

S&F aluminium window as per TD drg No. CEDZ/TD-316 with following specifications :- (i) Outer frame of size 40mmx114mm with 1.3mm thickness, corner 45 degree cut & aluminium welded. (ii) Center mullion of size 40mmx65mm. (iii) Welded shutter (02 Nos) of size 40mmx60mmx1.3mm thickness 45 degree cut mechanically joint with 6mm allen key bolt clamp with 5mm clear glass both side EPDM rubber gasket metal body hand lever type single point lock, aluminium kobra hinges 2 Nos per shutter. (iv) 12mm SS 202 grade round bar safety grill at 100mm cc distance modified to 150mm cc distance in front of handle, welded at both ends with 6mm SS 202 grade round bar. (v) Welded wiremesh shutter (2 Nos) of size 40mmx18mmx1.3mm thickness 45 degree cut with 0.45mm nominal dia of SS wire mesh, SS 75mm long hinges & PVC magnet. (vi) Entire window shall be powder coated with pure polyster coat of any shade as approved by GE. (vii) Windwo shall have provision for installation of window AC/Desert Cooler and provision of windwo glass shutter, wiremesh, grill and necessary fittings and locking arrangements for subject portion will be modified as per ground requirement during the execution as per directions of Engr-in-charge. (viii) Window shall be installed with silicone, complete all as specified and directed.

S&F factory made solid WPC (wood polymer composite) door frame 62mmx32mm single rebated made from WPC (single extruded process) material comprisin of virgin PVC polymer of K value 57-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk / weat husk) and non toxic additives fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 780 kg/cum, having good screw holding capacity (screw withdrawl strength of min 990 N), min compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixing in position with SS Dsh fasteners/ hold fast of required dia and length, complete all as specified and directed

S&F factory made WPC (wood polymer composite) soild plain board of 18mm thickness comprising of virgin PVC polymer of K value 57-60 (suspension grade) calcium carbonate and natural fibers (wood powder/ rice husk / weat husk) and non toxic additives made from extrusion process WPC foam sheet single extruded (inner) with density not less than 650 kg/cum, having screw withdrawl capacity ( screw withdrawl strength of 2000 N (face) 1100N (edge) min compressive strength of 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed countersunk SS screw, complete all as specified and directed

S&F 100mm size stainless steel handles with matt finish fixed with screws, complete all as specified & directed.

S&F magnetic catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions, complete all as specified and directed.

S&F hasp & staple, 125 size, safety type stainless steel hinges pin including bolt, to hinge plate and fixed with screws, complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flaps (when oepn) 40mm, complete all as specified and directed.

S&F in repairs stainless steel of grade SS-304 for curtain rod of 20mm nominal bore & 1.6mm thick of fancy type including brackets, side knobs etc, fixed to walls, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, complete all as specified & directed.

Taking up or down 20mm bore steel tubing and connections, complete all as specified & directed.

S&F 20mm outer dia CPVC pipes SDR 11 with and including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F 20mm outer dia CPVC Union complete all as specified and directed.

S&F 20mm outer dia CPVC Brass Elbow complete all as specified and directed.

S&F 20mm outer dia CPVC Brass Tee complete all as specified and directed

S&F 20mm bore GI tubing medium grade galvanised, with all fitting (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed complete to walls and ceilings or laid in floor, complete all as specified and directed.

Refixing of 20mm bore tubes, 'medium grade', galvanised, with all fitting; (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors, complete all as specified.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends to edges of landings, steps, cills, sunsheds,shelves, lintels etc. and cutting chases for concealed water tubing or cocealed conduit wiring, etc nad making good, cutting n,exc 10 cm girth (brick wall), all as specified and directed.

S&F in repair white vitreous china wash hand basin full pedestal (flat back) of size 550 x 400 mm fixed on and including new brackets complete including 32 mm size brass chromium plated waste coupling, pvc waste pipe of adequate length etc, complete all as specified and directed.

S&F in repairs Brass CP wall mixer 2-in-1 for mixing hot & cold water screwed down for iron pipe 15mm bore and fixed complete all as specified and directed.

S&F in repairs stop valves, cast copper alloy, fancy type, chromium plated with long shank & cup with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15mm bore, complete all as specified & directed.

S&F in repairs PVC connection 600mm long, 15mm dia PTMT (PVC heavy duty), complete all as specified and directed.

SF in repairs brass CP mixer for mixing hot & cold water for WHB screwed down for iron pipe and fixed complete all as specified and directed.

SF in repairs brass CP mixer for mixing hot & cold water for sink screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repair bib taps cast copper alloy CP fancy type with crutch or butter fly handles screwed down screwed for iron pipe or brass femule and fixed 15mm bore complete all as specified and directed.

S&F in repair chromium plated shower rose with arm or without swivel joints any size including fixing with 15mm pipe complete all as specified and directed.

S&F in repair brass CP tubular towel rail 10-12mm dia D type 60cm long between flanges complete all as specified and directed.

S&F in repairs white vitreous china squatting pan ‘ORISSA’ pattern of size 580 mm x 440 mm white with integral foot rests with ‘P’ or ‘S’ trap, front or back inlet including all connection and provision of lime concrete base complete all as specified and as directed..

S&F in repairs PVC low level flushing cistern, valve less, Syphonic action type, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 32 mm dia of required length and making connection complete all as specified.

S&F in repair soap dish brass chromium plated complete all as specified and directed.

S&F in repair 200x200mm high quality glass corner shelf made of 5mm thick of glass including u type CP brackets complete all as specified and as directed.

S&F in repairs sinks with drainage board made of stainless steel 0.8mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified & directed.

S&F waste coupling of PTMT (half or full threaded) for sink, minimum weight 60gms, suitable for discharge pipe of 32mm bore dia, complete all as specified & directed.all as specified.

S&F 32mm dia of adequate length PVC waste pipe including tail for stainless steel sink etc, complete all as specified.

S&F in repairs heavy duty stainless steel peg set of minimum size 450mm x 50mm with 6 pegs fixed on to walls/ doors with screws and necessary fittings, complete all as specified and directed.

Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks etc, complete all as specified & directed.

S&F 110mm bore white coloure PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls, complete all as specified & directed

S&F 110mm bore white coloure PVC (SWR) bends any radius, complete all as specified & directed

Taking up cast iron water mains (including all fittings) 100mm bore, with spigot and socket ends and lead joints including burning out joints and recovering lead, all as specified.

Taking up cast iron water mains (including all fittings) 75mm bore, with spigot and socket ends and lead joints including burning out joints and recovering lead, all as specified.

S&F of upvc 100mm waste and vent pipes in any length jointed neatly fittings with solvent cement and rubber ring joint as per manufacturers instructions to be laid in trenches or in floors complete all specified and directed.

S&F of upvc 100mm waste and vent pipes in any length jointed neatly fittings with solvent cement and rubber ring joint as per manufacturers instructions fixed to walls complete all as specified and directed.

S&F of upvc 75mm waste and vent pipes in any length jointed neatly fittings with solvent cement and rubber ring joint as per manufacturers instructions to be laid in trenches or in floors complete all specified and directed.

S&F of upvc 75mm waste and vent pipes in any length jointed neatly fittings with solvent cement and rubber ring joint as per manufacturers instructions fixed to walls complete all specified and directed.

S&F of upvc 100mm bend pipe(any radius), with or without acess door , diminishing pieces or tapersfitting jointed neatly fitted with solvent cement and rubber ring joint as per manufacturers instructions complete all specified and directed.

S&F of upvc 100mm tee single with or without acess door, (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branch fittings jointed neatly with solvent cement and rubber ring joint as per manufacturers instructions complete all specified and directed.

S&F of upvc 75mm tee single with or without acess door, (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branch fittings jointed neatly with solvent cement and rubber ring joint as per manufacturers instructions complete all specified and directed.

S&F of upvc 75mm floor trap with cp brass grating including jointing to waste pipes with solvent cement and rubber ring joint as per manufacturers instructions complete all specified and directed.

S&F of upvc 100mm floor trap with cp brass grating including jointing to waste pipes with solvent cement and rubber ring joint as per manufacturers instructions complete all specified and directed.

S&F of upvc 75mm vent cowl including jointing to waste pipes with solvent cement and rubber ring joint as per manufacturers instructions complete all specified and directed.

S&F of upvc 100mm vent cowl including jointing to waste pipes with solvent cement and rubber ring joint as per manufacturers instructions complete all specified and directed.

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified.

S&F in repair 1000 litres capacity double layer, rotational molded, polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe, complete all as specified and directed.

S&F in repairs 20mm bore pipe gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, all as specified.

S&F in repairs 40mm bore pipe gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, all as specified.

Dismantling brick tiles or terracing tiles single layer on roofs, complete all as specified & directed.

Demolition of mud/ mud phuska in roofs any thickness, including plastering and leaping if any and removal of mud /mud phuska to a distance exc 250 M and n exc 500 M, complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in roof padding including finished even & fair without using extra cement, complete all as specified and directed.

M&L for screed bed 10mm thick (average) on concrete surfaces in CM 1:3 on roof mixed with WPC and finishing the surface even & fair without using extra cement complete all as specified and directed (WPC shall be measured and paid seperately).

M&L for priming roof surfaces and applying water proofing treatment over roof including preparation & cleaning of roof surface comprising of the following complete all as specified & as directed:- (a) Applying oil bound bituminous primer at the rate of 0.4 Ltrs/sqm as per IS 3384-1986 on prepared surfaces. Surfaces shall be kept free till the moment, the primer is impregnated and the solvent oil in primer is evaporated. (b) Applying one coat of hot straight run bitumen @ 1.2 Kg/sqm of grade 85/25 confirming to IS-73. (c) Laying 3 mm thick APP polymeric water proofing membrane of weight not less than 3.6 kg/sqm, black finish reinforced with non woven polyester matt, with a thermo fusible finish, torching overlaps with a propane or a butane gas torch, with a overlap of 75 mm at sides and 100 mm at the ends and sealing including applying a coat of cold emulsion bituminous primer, all as per manufacturer's instruction including preparation of surface. Note: Water proofing treatment shall be got carried out through manufacturer or their authorised applicators. Contractor shall give 10 years guarantee for effectiveness of water prrofing treatment. An amount of 2.5% of workdone value of this item shall be retained from the contractor payment for a period of 10 years reckoned from date of physical completion of the work or in lieu contractor may deposit bank FDR for the said tory for 10 years which shall be released by GE on the expiry of satisfactory completion fo 10 years period, complete all as specified and directed.

M&L for precast PCC tiles macine pressed of size 25cm x 25cm x 20-22mm thick and joints grouted flush in cement mortar 1:3 mixed with integral water proofing compound over 20mm thick screed bed or bedding layer of mortar in cement mortar 1:6 complete all as specified and directed.

M&L for chipping of spilled and loose concrete and cleaning rust from reinforcement by sand blasting scrubing down concrete surfaces with wire brushes cleaning with water allow to dry and applying a layer of Zinc rich epoxy primer as an anti rust on all exposed reinforcement followed by a layer of binding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited and applying two layers of guniting over steel welded mesh 2mm dia of wire and aperture 75mm. Thickness of guniting ranging from 20 mm to 40 mm in cement mortar 1:2 using OPC 53 grade cement mixed with polycreate mixture @ 2% by weight of cement or as per manufacturer's instruction and finally applying cement plaster over guniting surface of required thickness to give even, uniform and smooth finishes confirming to proper geometrics in cement mortar 1:3 to match the existing surfaces as in sides, soffits of the slabs, chajjas, fins, facias, parapets, linetls, columns and beams etc complete including necessary scafolding, shuttering, chasing to brick work or RCC members at any height upto 6 storied buildings including removal of all small trees/ shrubs etc , complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil, all as specified.

Demolition of cement concrete (unreinforced) in ground floor and in paving n exc 15 cm thickness (below or above ground level), complete all as specified & directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate), as in foundations, filling and mass concrete complete all as specified.

Demolition and breaking up drain pipes (SGSW, AC or reinforced concrete) set in cement mortar of 200 mm internal dia of Pipe, complete all as specified & directed.

M&L for 200 mm size reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and directed

M&L PCC (1:3:6) type C-2 as in cement concrete bed to drain/ sewage pipe including packing under and haunching against the sides of pipes of pipe 200 mm internal dia after they are laid and tested complete all as specified and directed

M&L for cement concrete type B-2 1:2:4 (40mm graded aggregate) in surface channels and drains complete all as specified and directed

M&L for returning, filling in, including spreading, levelling, watering and well ramming in layers n, exc 25 cm soft/ loose soil, complete all as specified and directed

Removing excavated materials to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L for PCC type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in coping, band, plinth coarse, plinth band etc. incl use and waste of form work and finishing the surface smooth with slightly rounded or chamfered angles and throating as ordered complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to fecilitate demolition) complete all as specified and as directed

M&L for RCC type B1 1:2:4 (using 20mm graded crushed stone aggregate) as in slab supported on walls, beam and columns in floors, roofs, landing, balconies , canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required incl cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F TMT bars 6 to 8mm dia and over, cut to length, bent to shape required incl cranking bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for formwork to sofits of suspended slab such as roof slab, floor slab, landing and similar work not exc 200mm thick rough finish of surfaces, all as specified.

M&L for precast cement concrete Type B1 1:2:4 (20mm graded aggregate) in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, ater troughs,mangers, shelves and similar articles with plain fair faces,including chamfers,weatherings,throat- ing etc. and setting in cement mortar 1:6 complete with joints to match the surface complete all as specified.

M&L for 75 mm thick PCC type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection laid in bays n. exc. 2 sqm each, finishing the surface of concrete topping even & fair, without using extra cement filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand (all by weight), complete all as specified and directed.

M&L for 75mm thick cement concrete type D- 2, 1:4:8 (using 40mm graded aggregate) as in sub base, complete all as specified.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block with lacquer finish of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks with lacquer finish as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed.

M&L for rubber moulded glossy finish chequered cement concrete tiles of size 30 cm x 30 cm x 20-22 mm thick, in gray cement with pigment, set, jointed in neat cement slurry & pointed in coloured cement, as in floors / path / hard standing, laid over and including screed bed and bedding layer of mortar 15mm thick in CM 1:4 for laying floor finishes, complete all as specified and directed.

Taking down steel rolling shutter of any description incl all fittings and fixtures of openign size area min 10.5 sqm complete all as specified and directed.

S&F steel rolling shutters 1.25mm thick lath, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated but gear operated type with bevel gear box and crank handle, complete all as specified and directed.

M&L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10cm width or girth including preparation of steel surfaces complete.

S&F for stainless steel plate rack of size 90x80x25 cm depth size made out of 1mm thick sheet complerte all as specified and directed by Engineer-in-Charge.

M&L vitreous china water closet padestal pattern white including seat cover white colour for pedestal pan with hinges fixed in repairs complete all as specified and directed.

S&F in repair hand shower (health faucet) with 1.0 m long flexible tube, wall hook and wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified.

Material and labour for expose the first joint of masonry structure at ground level horizontally. the plaster must be knocked off at least 50 cm beyond the visibly penetrated area.damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. Drilling holes :- Drilling holes 10mm diameter in masonry structure along the side of the joint as per manufacturers instruction so as to cross the brick/block at the intervals spacing of 15-30 cm depending on extent of rising dampness as per recommendation of engineer in charge. Cleaning of holes :- Clean the holes by air blower prior to fixing nozzles. Install latex polymer packer injection packers 9.8mm diameter,10cm long in the holes and tighten. fix the packer securely using sealant.

Supply and apply of a 3 part , very low viscous , elastic polyacrylic injection resin with a versatile and adjustable reaction time having mixed viscosity : 3-11 m.pa.s at +20 deg c , reaction time : adjustable according to ambient temperature and execution requirement between 8-50 mins , ph- 9-10 , tested as per wissbau no. 2002-094-(1a)- function test with re-injectable hose system. The holes should be drilled until a depth of approx. 5 cm ( for a 6 cm thick wall) before the end of the wall is reached. Pump injection of polymer resin compound at > 20 bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas. If voids in masonry being injected contain insufficient moisture to activate the grout inject a small amount of water prior to injecting the grout. When movement stops or polymer compound appears at the packer move to the next packer and inject. If the dampness if heavy, inject similarly at the next joint line. Chemical use fosroc or equivalent.” Note :-Qty will be paid for the actual weight of the chemical used not for the diluted weight of the chemical with the water/admixture.

Description of Work / Item(s)

Amount

Taking down old unserviceable point wiring with and including existing conduit / batten type (light, fan, socket or power point) complete such as tube light any type switches, ceiling rose, pendent holder, regulator and socket etc and removing the material from site with chasing and cutting surface of wall / floor/ ceiling etc complete all as directed.

Taking down existing sub main wiring aluminium/copper 4/6/10sqmm of 3 runs complete all as directed.

Material and labour for point wiring complete with 1.5 Sq mm (nominal area) FRLS PVC insulated un-sheathed and stranded copper conductor cable ISI marked including cutting and chasing and PVC concealed conduit ISI marked of size 20 mm bore medium grade and PVC conduit fittings such as tees, bends, elbow, reducers including FRLS PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Modular Metal flush box, cover plate and other accessories of suitable size for fixing Modular switches / sockets / fan regulator of any type etc and making good surface as original by plastering and whitewash/ colour/ distemper etc, complete all as directed for one light point / fan point / exhaust fan point / bell / buzzer controlled by one 1-way Modular switch/ bell push. No cutting and chasing will be allowed in the roof slab for Fan point.

All as per srl item No. 3 here in before but point wiring for one socket outet point 5 amps on the same board.

All as per srl item No. 3 here in before but point wiring for one socket outet point 5 amps on the independent board.

All as per srl item No. 3 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for 15 Amp power point.

All as per srl item No. 3 here in before but point wiring for one light point controlled by two Nos of two way switches

All as per srl item No. 3 here in before but point wiring for one socket outlet for TV and cable outlet socket

Material and labour for Sub main wiring with 2 run of 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in and including PVC conduit with wall thickness 1.6mm thick and including 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB/Panel to sub DB complete all as directed. Note : 1. The two run of 4 Sqmm wire, one run of 4 Sqmm earth wire and 1 mtr PVC conduit pipe will be measured as one unit.

Material and labour for Sub main wiring with 2 run of 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in and including PVC conduit with wall thickness 1.6mm thick and including 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB/Panel to sub DB complete all as directed. Note : 1. The two run of 6 Sqmm wire, one run of 6 Sqmm earth wire and 1 mtr PVC conduit pipe will be measured as one unit.

S&F in repair modular switch, 06 Amps, single pole, one way, 250 volts, one module and IP 20 protection complete all as specified & directed

S&F in repair modular switch, 06 amps two way,SP,one module 230 volts AC all as specified and directed.

S&F in repair modular switch, with indicator, 16 Amps, single pole, one way, 250 volts, one module complete all as specified & directed

S&F in repair modular socket outlet 05 Pin, 06 Amps, 02 module with shutter complete all as specified & directed

S&F in repair modular socket outlet 02 in 01, 03 pin, 06 Amps and 16 Amps, 02 module with shutter complete all as specified & directed

Supply and fixing in replacement Modular Bell push switch, single pole, one way, 6 Amps, one module complete all as directed.

S&F in repair ceiling fan regulator, stepped type of 0 to 04 rotary steps, electronic, 02 module, humfree, AC, 230 volts, 100 watts, duly ISI marked complete.

Supply and fixing cable outlet socket for TV complete all as specified and directed.

Supply and fixing Telephone outlet socket including metal flush box and other connecting accessories complete all as specified and directed.

Supply and fixing rigid PVC conduit pipe of 20mm dia including tee, bends, saddles and other connecting accessories for TV and Telephone including cutting and chasing in wall and making good all the disturbed complete all as directed.

Supply and fixing multipurpose cable lead for TV complete all as specified and directed.

Supply and fix in replacement of Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps with and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed.

Supply and fix in replacement of MCB protected modular AC/Geyser box complete with and including 6 pin socket, plug top, modular cover plate, mini MCB SP 20 Amp capacity and PVC gang box etc, complete all as specified and directed by by Engineer-in charge.

S&F in replacement surface/wall mounted 20 watt LED batten, luminaire made up of extruded aluminium housing with PC diffuser. The luminaire should be IP 40 from dust. the LED used should have CRI ≥ 80 and CCT 6500K, luminaire system efficacy of ≥ 120 lumen per watt. Luminaire shall have life class of min 50000 burning hours. The electronic driver used shall have power factor ≥ 0.95. Fixture must have voltage range protection from 140-270 V along with inbuilt surge protection of min 2.5 KV. The luminaire shall pass insulation resistance test ≥ 2M Ohm .The luminaire working temp range should be from 0-50 °C. The luminaire shall passed electric strength test. The LED luminaire & its driver shall be of the same make. Manufacturer shall have inhouse lab approved by NABL as per 2019 standard.

S&F in replacement surface/wall mounted 10 watt LED batten, luminaire made up of extruded aluminium housing with PC diffuser. The luminaire should be IP 40 from dust. the LED used should have CRI ≥ 80 and CCT 6500K, luminaire system efficacy of ≥ 120 lumen per watt. Luminaire shall have life class of min 50000 burning hours. The electronic driver used shall have power factor ≥0.95. Fixture must have voltage range protection from 140-270 V along with inbuilt surge protection of min 2.5 KV. The luminaire shall pass insulation resistance test ≥ 2MΩ. The luminaire working temp range should be from 0-50 °C. The luminaire shall passed electric strength test .The LED luminaire & its driver shall be of the same make . Manufacturer shall have inhouse lab approved by NABL as per 2019 standard.

Supply and fix in replacement Building security light with high efficient high power LED street light 40 watt, having sensor ON/OFF the fitting automatically in the absence/presence of sunlight, with lens with pressure die cast aluminium housing and enclosed with toughened glass IP-66 including service bracket 1.2 mtr long by using 32 mm bore GI pipe and fixing accessories ( Clips, Fasteners, Nut, Bolts etc) Temparature (CCT- 5700K to 6500K) , PF>0.9 and Voltage rated 220V to 240V etc complete all as directed.

Taking down carefully ceiling fan of any size, sealing cable end, dismantling blades & removing fan and blades to store complete all as directed.

M&L for painting of ceiling fan complete with synthetic enamel paint by spraying including filling cavaties with filter one coat after cleaning all as directed

Hanging only with fixing accessories ceiling fan and connecting with and including 3 core flexible copper cable from ceiling rose to fan all as directed

Supply and fix in replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, recessed on wall, SPN 12 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc and making all necessary connections complete all as directed.

All as srl item no 30 here in before but of SPN 08 way type.

All as srl item no 30 here in before but of SPN 04 way type.

Supply and fix in replacement Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, recesses on wall, VTPN 4 way, 240 volts with bus bar rating 415 Amps, dust and vermin proof suitable for incorporation of MCCBs 4 pole, MCB TPN and MCBs etc and making all necessary connections complete all as directed.

All as srl item no 33 here in before but of VTPN 08 way type.

M&L in replacement MCB 6 to 32 Amp, B Curve type, 10kA, single pole with over load and short circuit protection complete all as directed.

Supply and fixing in replacement MCB, SPN type of 40 to 63 amps capacity, 240V, 10 KA with all connections complete all as directed.

All as srl item no 36 here in before but of 40 to 100 amps capacity, 415V 10 KA and TPN type.

Supply and fixing in replacement of MCCB 415V,4 pole 100 Amps, 16 kA with over load and short circuit protection complete all as directed.

Taking down carefully exhaust fan any size, seling cable and depositing to store complete all as directed.

M&L for painting of exhaust fan complete with synthetic enamel paint by spraying including filling cavaties with filter one coat after cleaning all as directed.

Fixing only exhaust fan and connecting up including provision of cable from ceiling rose to fan all as directed.

Supply and fix 9 W LED Bulb luminaire, B-22 base 6500K as specified by the Engr-in-charge.

Supply & Fix in replacement Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings all as directed by Eng- in Charge.

Supply & fix in replacement Bell Buzzer, Ding Dong single phase AC Supply 230 volts,

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of 6 sqmm area.

Dismanteling & re-fixing of Geyser including connection pipe, fastener, nut and bolts all as specified and directed.

M & L Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3 mm thick buried directly in ground earth pit not less than 2.25 mtr deep below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire all by means of nuts and bolt check nuts and washers of galvanised iron sheet all as shown in electrical plate Nos 5 of SSR Part - I and connected to and including earthing test point complete including testing filling of adequate quantity of charcoal dust and common salt including refilling earth and removal of surplus soil up to 50 mtrs PCC 1:3:6 type CI chamber precast RCC cover 40 mm thick reinforced with 6 mm dia MS bar 3 Nos both way with handle made but at 6 mm dia MS bar water pipe with wire mesh and connecting testing etc complete all as specified and directed.

Excavation in trenches in any kind of soil not exceeding 1.5 metre deep and not exceeding 1.5 metre wide for laying of pipes in trenches and getting out in soft and loose soil complete all as specified & directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick each, after laying of pipeline complete all as specified & directed.

Removing excavated surplus material to a distance not exceeding 50 metres and depositing where directed, at a level not exceeding 1.5 metre above the starting point, complete all as specified & directed.

Dismantling and taking out any type of water supply distribution mains/pipes of size ranging from 100 mm to 200 mm bore with all fittings complete all as specified & directed by Engr-in-Charge.

S&F DN 200 mm PVC-O pipe, Class 500, PN 16, IS 16647 : 2017 including specials, i.e. bend, elbow, tee, gasket, titan joints, spigot flange, nuts, bolts, washers, clamps etc. complete all as specified & directed.

S&F DN 160 mm PVC-O pipe, Class 500, PN 16, IS 16647 : 2017 including specials, i.e. bend, elbow, tee, gasket, titan joints, spigot flange, nuts, bolts, washers, clamps etc. complete all as sspigot flangepecified & directed.

S&F DN 110 mm PVC-O pipe, Class 500, PN 16, IS 16647 : 2017 including specials, i.e. bend, elbow, tee, gasket, titan joints, spigot flange, nuts, bolts, washers, clamps etc. complete all as specified & directed.

Taking out GI Tubing 80 mm bore, laid in trenches/, under the roads or fixed on roof and wall with and including all old fittings and connections, complete all as specified and directed.

All as per item No 55 here-in-before but for pipe of size 50 mm bore.

All as per item No 55 here-in-before but for pipe of size 40 mm bore.

All as per item No 55 here-in-before but for pipe of size 25 mm bore. Note for Srl item 51 to 58:- Excavation shall be carried out by manually by laboour and Excavator/JCB shall not be allowed to use. Excavation & earth work shall be measured and paid separately under relevant items, Dismantling and refixing of chequered tiles, interlocking tiles, making holes through walls or ground, making branches with any size as per existing site and make good are deemed to be included in quoted rate. If during testing any leakage is found or damaged to any utility then contractor should replace the same without any extra cost.

M&L GI tubing 80 mm bore, medium grade, ISI marked with and including all fittings i.e. tee, elbow, reducer, union, nipple, socket etc, in new or old position fixed complete to walls, floor or laid on floor/ trench complete all as specified and directed.

All as per item No 59 here-in-before but for pipe of size 50 mm bore.

All as per item No 59 here-in-before but for pipe of size 40 mm bore.

All as per item No 59 here-in-before but for pipe of size 25 mm bore.

M&L in replacement the CI Sluice valve of 200 mm rising PN 1.6 as per IS;14846 including CI flange with gasket of matching hole to fix easily to the existing system complete all as specified and directed.

All as per srl item No 63 here-in-before but of size 150 mm bore.

All as per srl item No 63 here-in-before but of size 100 mm bore.

All as per srl item No 63 here-in-before but of size 80 mm bore.

S&F in replacement gun metal gate valve/stop valve of 50 mm bore dia ISI marked to IS:778-1984 Class-I screwed in bonnet, non rising stem screwed ferrule ends with iron wheel head as per IS-554 complete all as specified and directed.

All as per Item No. 67 but 40mm bore

All as per Item No. 67 but 25mm bore

M&L for cutting of existing old rusted branch from header and make branch by dressing & welding with 200 mm pipe line & making good including all necessary connections to avoid any leakage complete all as specified and directed.

M&L construction of valve pit chamber of internal size 900x900x1200mm including necessary excavation, returning filling in, & removal of surplus soil to a distance not less than 250M, 100mm thick PCC(1:4:8) type D2 (using 40mm graded stone aggregate ) in foundation, 23 cm thick brick work in CM (1:4), PCC (1:2:4) type B1 (using 20mm graded stone aggegate) for coping inclduing necesary form work, 15mm thick plastering in CM (1:4) including 5mm thick M S Sheet cover fixed on MS angle iron 50x50x6mm, painting with two coats of synthetic enamel paint over a coat of red oxide primer on all steel/iron surfaces and provision of suitable locking arrangement complete all as specified and directed.

M&L for road cutting of average size 0.40m x 0.60 m for laying any type of pipe, including excavation, returning filling in, spreading, levelling well ramming in layers, soling with broken boulders/stones, WBM 7.5 cm thick coarse aggregate received from dismantling the existing road, premix carpeting 25mm thick using ready mix patch repair work, complete all as specified & directed. Note: Road cutting to be done by road cutting machine only and contractor shall make good the road after laying of pipe.

M&L PCC 1:2:4 type B-2, using 40 mm graded stone aggregate including, provision of necessary form work / brick work where required and finishing fair to the exposed surfaces including demolition of old PCC to facilitate laying of Pipes, complete all as directed.

M/s Innovative Coolings and Constructions (BID ID -3258195)

M/S Chhavi Constructions Co (BID ID -3257795)

M/S Parshant Associates (BID ID -3252848)

M/s Innovative Coolings and Constructions (BID ID -3258195)

M/S Chhavi Constructions Co (BID ID -3257795)

M/S Parshant Associates (BID ID -3252848)