PROVN OF PRE- FAB LIVING -IN ACCN AT AFS MUMBAI UNDER GE(AF)THANE

Amount

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft/loose soil , complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation, etc or for the shafts, well, cesspits, manholes, pier holes, etc n exc 10 Sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil , complete all as specified and directed by Engineer-in-Charge.

M & L Cement concrete type D2 1:4:8 (40 mm graded aggregate) as in foundations, filling and mass-concrete , complete all as specified and directed by Engineer-in-Charge.

M&L Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement Mortar 1:6, complete all as specified and directed by Engineer-in-Charge.

M&L cement concrete 75 mm thick, type D2 1:4:8 (40 mm graded stone aggregate) in sub base of flooring , complete all as specified and directed by Engineer-in-Charge.

M&L 100 mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregates ) as in hard standing etc , including necessary form work, finished even and smooth without using extra cement , complete all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in plinth protection finishing even and smooth without using extra cement , complete all as specified and directed by Engineer-in-Charge.

Use & Waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and directed by Engineer-in-Charge.

M&L for TMT steel bars 10mm dia and over cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securing with clips in main bar , complete all as specified and directed by Engineer-in-Charge.

M&L for TMT steel bars 8mm dia cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securing with clips in stirrups, complete all as specified and directed by Engineer-in-Charge.

M&L reinforced cement concrete Design Mix M-30, as in foundation including rafts, footings, foundation beams, plinth beams bases for columns, etc: basement slabs, under-reamed piles and mass concrete, complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil, complete all as specified and directed by Engineer-in-Charge.

Spreading and levelling of soft/loose soil in floor in layers n exc. 25 cm thick including well ramming watering as required , complete all as specified and directed by Engineer-in-Charge.

Removing excavation material exc 250m but n.exc 500 m and depositing where directed at a level n.exc 1.5 mtr above the starting point , complete all as specified and directed by Engineer-in-Charge.

M&L for 15 mm thick cement plaster on stone or concrete surfaces in CM 1:4 mixed with water proofing compound @ 200ml by weight of cement, complete all as specified and directed by Engineer-in-Charge. complete. [Note:- WPC shall be measured and paid separately ]

Supply of liquid water proofing compound as per manufacturer instruction, complete all as specified and directed by Engineer-in-Charge.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 Litres/10sqm over and including priming coat of exterior primer applied @ 0.90 Ltr / 10sqm over new surfaces, complete all as specified and directed by Engineer-in-Charge.

M&L Hardcore of Broken stone or boulders gauge exc 63 mm but n exc. 100 mm , deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface ,complete all as specified and directed by Engineer-in-Charge.

M&L cement concrete 100 mm thick, type D2 1:4:8 (40 mm graded stone aggregate) in sub base of flooring, complete all as specified and directed by Engineer-in-Charge.

S&F machine pressed precast coloured concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness, M-35 Grade with mixture of grey cement and pigment over 20mm thick sand ( sand paid separately) ,complete all as specified and directed by Engineer-in-Charge.

Sand filling under floors or in foundation including watering and consolidation, 20 mm thick ,complete all as specified and directed by Engineer-in-Charge.

M&L for PCC type C-2 1:3:6 (40mm graded aggregate) as in foundations, filling and mass concrete, complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete bed to drain pipes in PCC 1:3:6, type C2 (using 40mm graded stone aggregate), for 150mm dia drain pipe including packing under and haunching against the sides of pipes with concrete after they are laid and tested, complete all as specified and directed by Engineer-in-Charge.

M&L for reinforced concrete pipe of 150mm bore of pipe, class NP-2, laid and jointed in cement mortar (1:1) complete with collars ,complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:2:4) type B-2( using 40 mm graded aggregate) as in benching to surface channels for manholes or drains etc, complete all as specified and directed by Engineer-in-Charge.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred / stopped ends etc complete all as specified and directed by Engineer-in-Charge.

M&L, rendering 10 mm than fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement , complete all as specified and directed by Engineer-in-Charge.

M&L for pre-cast reinforced cement concrete 1:2:4, type B1 (using 20mm graded stone aggregate) as in manhole cover with plain fair surface including chamfers, weatherings, throatings, necessary form work and set in CM (1:6), placed in position ,complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:2:4, Type B-0 (using 12.50mm graded stone aggregate) as in coping, including necessary formwork, weathering, slightly rounded or chamfered angles and throating ,complete all as specified and directed by Engineer-in-Charge.

M & L for Mild Steel TMT Bar 8mm dia as in reinforcement, cut to length, bent to shape required, including cranking bending and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips ,complete all as specified and directed by Engineer-in-Charge.

M/L for cutting into existing manholes for connecting new sewer line of dia 150mm, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required ,complete all as specified and directed by Engineer-in-Charge.

Supplying & Laying, connecting and testing GI pipe 80 mm bore medium grade including necessary fittings in trenches, complete all as specified and directed by Engineer-in-Charge.

All as per above item No 32 here-in-before but of size 50 mm bore , complete all as specified and directed by Engineer-in-Charge.

All as per above item No 32 here-in-before but of size 40 mm bore ,complete all as specified and directed by Engineer-in-Charge.

All as per above item No 32 here-in-before but of size 25 mm bore, complete all as specified and directed by Engineer-in-Charge.

All as per above item No 32 here-in-before but of size 20 mm bore ,complete all as specified and directed by Engineer-in-Charge.

Supply and fix Sluice Valve Class PN 1.6 80 mm dia with iron wheel head, gaskets nuts, bolts, washers ,complete all as specified and directed by Engineer-in-Charge.

Supply and fix gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe of sizes 50 mm dia, complete all as specified and directed by Engineer-in-Charge.

Supply and fix gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe of sizes 40 mm dia ,complete all as specified and directed by Engineer-in-Charge.

Supply and fix gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe of sizes 25 mm dia ,complete all as specified and directed by Engineer-in-Charge.

M&L chamber of size 1200x1200x900mm including unserviceable rusted MS cover complete without disturbing the existing pipe lines valves and provide valve chamber including necessary earth work in any type of soil PCC 1:1.5:3 in base concrete brick work in CM (1:6) with 10mm thick plaster internally and 15mm thick externally in CM (1:4) 6mm thick MS sheet cover with hinges and locking arrangements fixed to angle iron frame made out of 502x50x6mm MS complete with 2 coat of synthetic enameled paint over a coat of red oxide on all steel work and 2 coats of white washing on plastered surface of valve chamber of any sizes ,complete all as specified and directed by Engineer-in-Charge.

Material and Labour for cutting bituminous surfaces road to a depth of n exc 60cm and not exceeding 60cm in width for taking out or laying of GI tubing and refilling the same with necessary making good works ,complete all as specified and directed by Engineer-in-Charge.

Construction of Pre-Fab Structure Supply & erection of Pre-fabricated Galvanized Insulated Contenarised Portable Accommodation Cabin of Size 40 feet X 20 feetX 10 feet, with sloped roof on top side to accommodate 14 persons etc., complete all as specified and shown on drawing inclusive of all fittings and fixtures mentioned on drawings and mentioned below along with base frame made with MS hollow box section of size 100mm x 50mm x 3mm thick with internal grid, sides wall made of rock wool sandwiched in between external GI sheet & inside 8mm laminated particle board, ceiling top made with 50mm thick rock wool with 8mm laminated sheet, flooring 19mm cement fibre sheet with 2mm PVC carpet on top including outside & inside colour in four layer of (1st layer - Zinc based primer, 2nd layer - epoxy primer, 3rd and 4th layers - Epoxy paint) as approved by GE including all electric wiring, fittings and fixtures . (a)Point wiring of ISI mark-Make-Polycab. (b) Switches, sockets and combination 5A -14 Nos (make Anchor) . (c) Tube light LED 20 Watts 4' long -14 Nos. (d) Tube light LED 10 Watts 2' long -10 Nos. e) Exhaust fan 380 mm-05 nos (e) SPN DB 8 way Double door -01 No. ( f) MCB SPN40Amp-01 . (g) Bulk head -01 Nos. (h) MCB SP 6-32 Amp -06 No.Make as pore Approved List. Internal fitting and furniture like attach beds with storage, plastic chairs & tabled for all occupants including provision of overhead storage arrangement for all occupants, aluminium doors and sliding window made of powder coated aluminium with grills should be insulated galvanised with weather sheds outside, all as per attached drawings, Note:- B/R and E/M fittings all as per Drawing and as when required it should be vary according to site requirement with out any extra cost, the rate should be inclusive of all , complete all as specified and directed by Engineer-in-Charge. Make : Hindustan Prefab Ltd. (HPL)/ Boroplast / Everest industries Ltd / Epack Prefab / Pressmach Insfrastacture / Loom Crafts or any MES authorised company .

Supply & erection of Pre-fabricated Galvanized Insulated Contenarised Portable toilet Cabin of Size 24 feet X 12 feet X 10feet with sloped roof on top side to toilet annexe etc, complete all as specified , directed and shown on Drawings including all fittings and fixtures mentioned in Drgs and as mentioned below with base frame made with MS hollow box section of size 100mmx50mmx3mm thick with internal grid, sides wall made of rock wool sandwiched in between external GI sheet & inside 4mm ACP sheet, ceiling top made with 50mm thick rock wool covered with 4mm ACP sheet, flooring 19mm cement fibre sheet with 2mm PVC carpet on top, toilet partition made made of 12 HPL board of approved shade, including outside & inside colour as approved by GE and also including provision of 05xWCs( Pedestal pattern) with PVC flushing Cistern, 05xBathrooms including taps , soap tray , 02xUrinal with springlers and down pipe, 02x Wash Hand Basins and two looking mirrors ,all sanitary fittings & fixtures makes as per list of manufacturers and 02 Nos 750 Ltr capacity water storage tanks with provision of electric wiring, fittings and fixtures (a)Point wiring of ISI mark-Make-Polycab. (b) Switches, sockets and combination 5A - (make Anchor) . (c) Tube light LED 20 Watts 4' long -3 Nos. (d) Ceiling fan 1200mm sweep-14 Nos. (e) SPN DB 12 way Double door -01 No. ( f) MCB SPN 6-32 Amp-01 . (g) Bulk head -02 Nos. (h) MCBSP 6-32 Amp -01 No. (j) AC Point with AC-02 Nos.Make as pore Approved List and aluminium doors & sliding window made of powder coated aluminium with grills should be insulated galvanised with weather sheds outside, all as per attached drawings, Note:- B/R and E/M fittings all as per Drawing and as when required it should be vary according to site requirement with out any extra cost, the rate should be inclusive of all , complete all as specified and directed by Engineer-in-Charge. Make : Hindustan Prefab Ltd. (HPL)/ Boroplast / Everest industries Ltd / Epack Prefab / Pressmach Insfrastacture / Loom Crafts or any MES authorised company

Removing excavated material n. exc. 50 M away, depositing as directed at level n. exc. 1.5 M above starting point complete all as specified and directed .

M&L for providing crushed stone sand cushioning to UG cable including punning down of sand in layers complete all as specified and directed

Supply and laying unreinforced precast concrete cable cover factory made embossed the mark “LT CABLE” class LV type1 flat size 250x150x40 mm laid in trenches complete all as specified and directed

Supply and lay in trenches / along the wall / floor pipes GI light grade of size 100 mm with and including all fittings and accessories complete all as specified and and directed for cable protection complete all as specified and directed

Supply and lay cable XLPE Insulated armoured, heavy duty electric power cables (heavy duty) 1100 Volts grade cross sectional area with stranded aluminium conductor of size 50 sq mm 3.5 Core complete all as specified and directed.

S & F outdoor Heat shrinkable end termination kit for 1100 volt grade cable complete with jointing material and accessories suitable for 3.5 core 50 XLPE armoured aluminium conductor LT cable of including cutting and taking out of unserviceable cable end termination jointing kit complete all as specified and directed .

Supply, install, testing and commissioning of factory made and CPRI tested outdoor type floor mounted on PCC Plinth. LT panel board cubicle type panel board suitable for 415 volts, 3 phase, 4 wire, 50 Hz AC supply system having bus bar chamber with air insulated PVC sleeved with heat shrink of colour code on copper bus bar of rating 350 Amps for phases and 250 Amps for neutral fixed on porcelain insulators. The panel shall be weather proof, dust and vermin proof IP-54 class protection and fabricated out of 3.0 mm CRCA sheet duly powder coated after seven tank process and pedestal of size 50 x 50 x 6 mm thick MS angle iron frame work. the panel shall be both front and back openable type adequate space all around accessories such as LT switchgear and measuring instruments on both sides including internal wiring in the panel with PVC insulated multi stranded copper conductor cable 1100 Volt grade marked or PVC sleeved copper strips of appropriate size as per standard in practices and including comprising of followings accessories all as specified and directed. INCOMING (a) MCCB 415 Volts, 200 Amp, rating 4 Pole (triple pole and neutral)(Service Breaking Capacity 35 KA-01 No (b) Digital volt meter 0-500 Volts-01 (c) Digital Ampere meter 0-100 Amps with and including CTs-01 No OUTGOING (a) MCCB 415 Volts, 100 Amp, rating 4 Pole (triple pole and neutral), (Service Breaking Capacity 25 KA - 03 Nos. (b) Internal wiring of panel with stranded copper cable of suitable size (c) Neon phase indicating lamp(Set of three)-01 Set (d) Stencilling of panel board including marking of distributions

M&L Earthing complete with galvanised electrode 60×60cm ×6mm size &galvanised earth lead 4.0mm dia by means of bolts, nuts and washer with galvanised plate buried in ground not less than 1.5 Mtrs deep with PCC chamber complete all as specified and as directed means of bolts, nuts, check nuts and washers of brass check nuts and washers of brass including necessary earth work, PCC chamber , CI cover with frame, funnel, mesh, Earth lead protection pipe, 7.5 Meter Earth Lead etc all as shown in electrical plate No 3 in SSR Part-I and connected to earth test point/LT Panel/Transformer including testing on completion all as directed by Engr in-Charge

Jay Jyotirling construction co. (BID ID -3339474)