SPL REPAIR TO BLDG NO P-36 (01 TO 15) AT SHIVAJI LINE, BLDG NO P-141 (01 TO 04) AT OLD KALINGA LINE, PROVN OF COVERED SHED NEAR BLDG NO P-84 AND CONSTRUCTION OF SHED AND OTHER CONNECTED WORKS AT STN MANDIR UNDER AGE B/R-I AT GE JHANSI

Amount

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 with water proofing compound finished fair and even complete all as specified and directed. Note :- water proofing compound shall be measured seprately.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1.6 finished fair and even complete all as specified and directed.

Rendering 10mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified and directed

Preparing newly plastered surfaces of new wall and applying two coats of weather proof exterior grade emulsion over and including a coat of exterior grade cement based primer complete all as sppecified and directed

Preparing newly plastered surfaces of wall and applying two coats of distemper oil emultion over a coat of wall care putty complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as sppecified and directed.

Preparing newly plastered surfaces of wall and applying three coats of white wash complete all as sppecified and directed.

M&L for preparation of existing surface of walls by complete removal of existing treatment and applying two coats of Oil bound distemper over and including a layer of wall care putty for complete smooth finish of surfaces complete all as specified and directed.

Demolition of cement concrete in ground floor including terrazo flooring and paving n exc 15cm thickness (below or above the ground level) built in cement mortar, complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for Non-skid cermaic coloured tiles (mat flooring) Size 300X300X7 to 8mm thick, in each floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Coloured Glazed ceramic tiles 450x 300 x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick rendering in CM 1:4 on wall complete all as specified and directed.

M&L floor Jointless Non-skid cermaic tiles 7 to 8mm thick (squre/rectanglar) are of each tiles 600X600, in each floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per Ser item No 14.00 above but in skirting including 10mm thick backing coat in CM 1:4 on wall complete all as specified and directed.

M&L for 100mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate), as in sub base complete all as specified and directed.

M&L for 75mm PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection, laid in alternate panels not more than 3 mtr in length, laid to slope 1 30 finished even and smooth without using extra cement with provision of forming joints duly filled with bitumen mastic, complete all as specified and directed. Note: Rate for forming joint and filling bitumen mastic shall be included in the same item.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removal to store complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for Refixing or removal to store complete all as specified and directed.

S&F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc, fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F in repairs 15 mm bore Bib taps, fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15 mm bore Bib taps long body fancy type cast copper alloy,chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15 mm bore stop/angle cock fancy type.chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15 mm bore concealed type stop cock fancy type,chromium plated with long sank crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F 500 litres capacity Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PVC float valve complete all as specified in SSR Part I including disconnectiong of existing tank complete all as specified and directed.

S & F in repairs 20 mm bore Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back, size 580x450mm excluding taps, waste chain and plug and porcelain stopper but including brackets, CP waste copling including PTMT PVC connection 600mm complete all as specified and directed .

S&F 15 mm brass mixture fancy type,chromium plated for mixing hot & cold water with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F Chromium plated shower rose 125 mm size with or without swivel joints, any size including fixing to steel pipe or union complete all as specified and directed.

Supply and Fix in repairs 10 Litres, PVC, valve less, syphonic action type, Flushing Cistern, high level, white inlet, ball valve, float, chain and pull, and brackets including PTMT PVC connection 600mm long complete all as specified and as directed.

S&F in repair of towel rail 20mm dia 600 mm long and wall bracket made of cast copper alloy, chromium plated, complete all as specified and as directed.

Supply & Fix in repairs Vitreous China Squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rests complete all as specified and directed.

M&L for Green marble 18/20 mm thick in steps, pillars, window cills, pillars, window cills, cooking platforms and like laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

Taking down eaves gutter and rain water pipes including all fittings any size and pattern complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls/trench complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls/trench complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single (Single "T) equal or unequal complete all as specified and directed.

S&F 75 mm bore PVC (SWR) junction single (Single 'T') equal or unequal complete all as specified and as directed.

S&F PVC Floor trap of 75 mm outlet with grating including jointing to waste pipe in run lead complete all as specified and as directed.

M & L for Plain Cement Concrete Type C1 (1:2:4)(using 20 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates hold fast and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work complete all as specified and as directed.

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sq M each (without taking off shutters from the frame) complete all as specified and as directed.

Taking down Chowkats or frames Not exceeding 1,5 Sq M each (without taking off shutters from the frame) complete all as specified and as directed.

Taking down shutters of any description exc 1.0 Sqm but not exceeding 2.00 Sq m each complete all as specified and as directed.

S&F Mild steel Angles, bars, flats etc, as in supports for stiffening of fencing, wall ties, hold fasts, clamps, plain angle cleats for securing purlins and similar small articles confirming to Fe 290. GdeE-165 complete all as specified and as directed.

S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for secunng glass etc complete all as specified and as directed.

S&F 35 mm thick factory made flush shutters solid core construction with block board core and plywood face panels, commercial type on both side complete all as specified and directed

S&F Solid PVC door frame of size 50mmx47 mm single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing complete all as specified in SSR Part-1 2010 section 8 complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2. 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & foing in frame at site as per specification & drawing complete all as specified and as directed.

S&F of 100mm butt hinges medium weight cold rolled mild steel ISI marked and fixed with mild steel wood screws or welded to angle frame, complete all as specified and directed.

S&F of 100 mm size butt hinges, extruded aluminum alloy with galvanized mild steel pin type B-21 anodized complete all specified and directed.

S&F of 75mm butt hinges medium weight cold rolled mild steel ISI marked and fixed with mild steel wood screws or welded to angle frame, complete all as specified and directed.

S&F of 200 mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed with screws, complete all as specified and directed.

S&F of 150mm long mild steel pressed handles, oval type, stove enamelled black and fixed with screws, complete all as specified and directed.

S&F of 300mm long mild steel, sliding door bolt plate type, stove enamelled black, with bright bolt not less than 12mm dia with and incl minimum of 6 bolts and nuts, complete all as specified and directed.

S&F 200 mm Aluminium alloy, anodised, sliding door bolt with hasp staple (bolt type) and fixing clips of sheet. cast or extruded sections and foong bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F of 150mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 100mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F of 150mm aluminum handle cast type anodized complete all specified and directed.

S&F of 100mm aluminum handle cast type anodized complete all specified and directed.

S&F of mild steel ordinary rat tail rod pattem springs of size 300mm including roller and roller plate complete all as specified and directed.

S&F for Door stopper 140 mm of aluminium alloy body anodised with tongue of rubber bush at one end fixed to door complete all as specified and directed.

Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and as directed.

S&F Box type steel windows with 80x40x1.25mm MSRectangular hollow section frame with side hung shutters (double shutters for glass and gauze) with out sash bars jointed together with and including grills using 12mm square bars @ 10cm C/C Ref TD No CEBZ/TD/14/2011 including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welded complete all as specified and directed.

S&F Box type steel Ventilator with 80x40x1 25mm MS Rectangular hollow section with side hung shutters (double shutters for glass and gauze) with out sash bars jointed together with and including grills using 12mm square bars @ 10cm C/C Ref TD No CEBZ/TD/14/2011 including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welded complete all as specified and directed.

Preparation of New or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary lint) over a coat of red oxide complete all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.71 mm nominal dia of wire and average width of aperture 1.40 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

S&F for stainless steel kitchen plate rack size 750x600x230 mm including foxing arrangement to walls with rawel plug or wooden plugs complete all as specified and as directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and waste cupling, wastepipe, including bedding in cement mortar to dwarf wall or including fooing cantilever brackets and connecting union to pipe overall size 915mm x460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

M&L for stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and SS wall mounting brackets, complete all as specified and directed.

Demolition of brick work or stone/ boulder Masonry, built in cement mortar including all quoins, pillars etc complete all as specified and as directed.

M&L for Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for Brick work with fly ash bricks, straight or curved on plan to any radius radius in half brick thick wall built in cement mortar 1:4 complete all as specified and as directed.

Demolition of RCC Not exc 15cm thickness Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work complete all as specified and as directed.

M&L for RCC Type B2 1:1.5:3 (20 mm stone agg) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, chajja, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L for mild steel deformed TMT bars 5 mm To 10mm dia (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column. hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs and lintels, chajja landingand similar work n exc 200mm thick complete all as specified and directed.

Dismantling of wall and ceiling board (fibre, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed

S&F grid false ceiling GI sysyem powder coated prelude (main runner sec 32 x 24 x 0.30x3600mm, cross tee 25x24x0.30x1200mm, wall angle 24x24x0.40x3000mm and including providing and fixing 4mm thick non asbestoss cement fibre designer (E-board) size 595x595mm in ceiling frame work, complete all as specified and directed.

Dismantling Asbestos Cement Corrugated or Semicorrugate in Roof covering complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for factory made PU coated, machine pressed precast concrete interlocking paver block of any shape and size confirming to IS 15658-2006 of 80mm thickness M-40 Grade with grey cement with pigment made of PVC moulded (or rubber mould) with vibrating system, with and including 50mm thick sand cushioning, including in CM (1:3) in edges of pavers, complete all as specified and directed. Note :- The cost of sand cushion is included in quoted rate.

Dismantling timber scantling 40 Sqcm and over in section in any position as in framed Junframed works such as roof purlins, rafters, fillets, ridges etc as in ceiling complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided all as directed and directed.

M&L mild steel work as roof trusses (framed) trussed, purlins, crane gantries rails and fastenings and heavy brackets framing (beams, tee, angle, channels or flat sections) etc complete all as specified and directed

Excavation im trenches not exceeding 1.5 meter wide and not exceeding 1 5 meter in depth for pipe line or for manholes not exceeding 10 Sqm on plan and not exceeding 1.5m in depth in hard/dense soil And getting out complete all as specified and directed.

All as per Ser item No 90.00 above but depth exc 1.5m and n exc 3.00m complete all as specified and directed.

Returning, filling in (soil) including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick in any type of soil complete all as specified and directed.

Removal of excavated material (soil) to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M&L Concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested in cement concrete 1.3:6 type C-2 (Nominal mix) using 20 mm graded crushed stone aggregate for 150 mm bore pipes complete all as specified and directed.

M&L Salt glazed stoneware (SGSW) drain pipes 150 mm bore laid and jointed on concrete bed, complete including testing etc complete all as specified and directed. Note : Concrete bed shall be measured and paid for separately.

M&L Cement concrete 1:3:6, type C-2 (Nominal mix) using 40 mm graded crushed stone aggregates in foundation filling and mass concrete complete all as specified and directed.

M&L Cement concrete M-15 (Nominal mix) using 20 mm graded crushed stone aggregate in coping, benching and the like including weathering, slightly rounded or chamfered angles as directed including form work and finishing all exposed surfaces complete all as specified and directed.

M&L for Precast cement concrete type B-1, 1:2:4 (Nominal mix) using 20 mm grade crushed stone aggregate, as in cover slabs (for manhole etc.) casted at site and setting in cement mortar 1:4 complete all as specified and directed.

Use & waste of form work to soffits of suspended slabs, floor slab etc not exc. 200 mm thick in flat complete all as specified and directed.

Use & waste of form work to edges of concrete flats etc exc. 5 cm but not exc. 10 cm wide/thick complete all as specified and directed.

Cutting into existing manholes for connecting new drains internal dia of pipe 150 mm, making good to pipes and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 12.4 type B-1 smooth finished, and reforming benching as required complete all as specified and directed.

S&F in replacement 75mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears fixed to walls with clamps and cement joints complete all as specified and directed.

S&F in replacement Cl bend or reducer/ taper of 100mm bore including cement joints complete all as specified and directed.

S&F 25mm thick flush shutter for cup board solid core construction with block board core and plywood face panels commercial type on both sides etc with and incl min 5 mm thick wooden beading fixed all around complete all as specified and directed.

S&F 25mm thick flush shutter solid core construction with block board core and plywood face panels commercial type on both sides etc, fixed with nails in any situation as in cup board shelves, complete all as specified and directed.

S&F 18mm thick prelaminated MDF board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in any situation as in cup board shelves/shutter or similar work, complete all as specified and directed.

S&F continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 30mm, complete all as specified and directed.

Demolition existing water proofing treatment by brushing with wire brush, cleaning of terracing by taking down cement concrete, existing plaster lime cova 80 to 100mm thick mud phuska/cement concrete/lime cova etc, cleaning of all foreign material such as fungus mass dust etc, roughing surface of corner to roof by wire brush complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in padding levelling etc and roof kerbs complete all as specified and directed.

Supply only liquid water proofing compound, mixed in CM as per manufacturer instruction, complete all as specified and directed.

M&L of water proofing treatment to non-accessible roof slab withproviding / applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers by Graco tex sprayer having sun reflective index (SRI) of 105 Mfd by Asian paint Ltd / Berger and Equivalent as approved by GE in three coats laid as per manuacturer's instructions complete all as specified and as directed with following course of description below :- (a) 10 mm thick plaster in CM 14 with WPC will be applied over the roof slab when concrete is green After the plaster is cured the roof will be tested for water tightness by ponding with water for seven days for any seepage is observed the rectification will be carried out by pressure grouting under the pressure of 5kg/sqcm using cement based cement grout. After the surface is repaireds the slab will be tested for water tightness again before proceeding with further treatment. (b) the surface of roof, parapet and gutters, drain mouths, etc: over which waterproofing treatment is to be applied shall be cleaned of all foreign matter such as, fungus, moss, dust etc by wire brushing and dusting For cast iron drain out lets a grove shall be cut around to tuck in the treatment Concrete angle-fets shall be provided at junctions between roofs and vertical faces of walls (parapet and other walls) around obstacles such as pipes, chimney stacks, etc and other similar situation to ease up about comers. (c) 1st coat of self priming of elastomeric waterproofing liquid(dilution with water in the ratio of 3:1). (d) 2nd & 3rd coat of undiluted elastomeric water proofing liquid(dry film thickness of complete allocation/system not less than 500 microns). (e) All joints and changes in direction should be curved with cement mortar 1:3 mixed with SBR latex 200ml per bag of cement and cured well before laying the roof treatment. Note: 1. fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers contain Tensile strength of 2.90Mpa, Elongation upto 350%, solid content 55.90 crack bridging ability upto 2.5mm. 2. Treatment shall be done through authorise representative of manufacturer and atleast 10 years water proofing warranty by manufacture

M&L for machine cut Kota stone satircase, step 18-20 mm thick and laid over and incl 15mm thick screed bed in CM (1:8), set and jointed with grey cement slurry mixed with pigment to match the shade of the slab, with and including Cutting Griding/mirror Polishing on Kota stone as per local trade practice, complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

M & L for reinforced cement concrete in nominal mix type B1 1:2:4 using 20 mm graded aggregate as in chajjas complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Use and waste formwork to fair finished surface of chullah hoods, chajjas, troughs and similar items including edges of flat concrete surface complete all as specified and directed.

M & L for machine cut granite (of any type) slab/ tiles 20mm thick, bedded and jointed in counter with gray cement slurry and pointed with white cement with admixture of pigments to match the shade of granite stone including grinding, polishing and making hole in platform for gas pipe with 1:4CM complete all as specified and directed.

Demolition of cement concrete of any description and in any position of WC’s/Bathroom etc in sunken portion area above ground floor, removing demolished material completely and old waste pipe from sunken portion and cleaning the side/bottom surface of sunken floor with wire brush, complete all as specified and directed.

M&L for application/forming of waterproofing liquid membrane moistening the prepared surface for proper dispersion and penetration and applying two component cementitious elastomeric water proofing coating damp block 2k as per manufacturers specifications. The treatment shall be carried out to the entire bottom surface and vertical surface upto the bottom height of wall tiles. Adequate curing to be done on vertical surfaces and ponding test for 48 hours on the bottom surface to be carried out complete all as specified and directed. NOTE : (a) Treatment shall be done through authorised applicator/representative of the manufacturer only. (b) Warranty for water proofing to be submitted by the contractor as per manufacturer norms

M&L for PCC 1:5:10 Type E2 using 40mm graded stone aggregate as in mass filling in two layer in sunken portion, complete all as specified and directed.

M&L for 50mm dia GI pipe as in spout to drain out if any leakage occures in the sunken portion, complete all as specified and directed.

M&L for rendering 15mm thick in 1:4 CM on fair faces of brick work or concrete surface wall and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick plastering in 1:6 CM fair faces of brick work or concrete surface wall and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in CM (1:3) on ceiling, finished even and smooth without using extra cement complete all as specified and directed

M & L for rendering 5mm thick in 1:4 CM for concrete surface of parapet wall finished even and smooth without using extra cement complete all as specified and directed

Demolition of brickwork or stone/ boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlars facings, dressed stonework and precast concrete articles, complete all as specified and directed

M&L for brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6, complete all as specified and directed

M&L for preparation of new plastered surface and applying two coats of oil bound distemper, over and incl a layer of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed.

M&L for preparation of new plastered surface and of wall and applying two coats of cement base paint , over over a coat of cement base primer over outer surface of wall, complete all as specified and as directed.

M&L for preparing old surfaces and applying one coat of oil bound distemper white or any tint on ceiling complete all as specified and directed.

M&L for preparing old painted steel surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old surface and applying one coat of white wash (lime) on walls including cornices plastered or un-plastered surfaces complete all as specified and directed .

All as per Ser item No 132 above but on ceiling complete all as specified and directed.

M&L for preparation of existing surface of walls and applying two coats of cement base paint over a coat of cement base primer complete all as specified and directed.

M&L for preparing new surfaces of steel of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed

S & F Pressed steel door frame of size 125x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed. Note : Cost of filling of PCC (1:3:6) type C-0 in hollow portion of frame id deemed included in these items

S & F Pressed steel door frame of size 105x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed. Note : Cost of filling of PCC (1:3:6) type C-0 in hollow portion of frame id deemed included in these items.

S&F 35mm thick Modular flush doors, solid core construction, with block board core and pre-lamination on both sides, complete all as specified and directed.

S & F 35 mm thick 2nd class hard wood glazed and skeleton shutters as in Doors open rebated and prepare to receive glass , gauze etc (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed.

S & F butt hinges 100 mm sizes medium weight, cold rolled mild steel fixed as in door chowkats complete all as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm with single side prelam PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, in opening as per specification & drawing complete all as specified and directed.

S & F factory Made Solid PVC Moulded Door Shutter with particle board core , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed

S & F Aluminium anodised, barrel tower bolts of extruded section of length 150 mm and fixed with cadimium plated wood series, complete all as specified and directed.

Taking down shutters n exc 1.00 sqm each complete all as specified and directed.

All as per Ser item No 144 above but exc 1.00 sqm and n exc 2.00 sqm in each complete all as specified and directed.

S&F of 20mm thick flush shutter/shelves for cupboard solid core construction with block board core and plywood face panels commercial type on both sides etc with and including min 5 mm thick wooden beading fixed all around complete all as specified and directed.

S & F in repair continuous (piano) hinges with 40 mm width of flaps (when open), mild steel, bright finish or electro galvanized complete all as specified and directed

S & F hasp and staple safety type aluminium with hinge pin including bolt to hinge plate of 100 mm size and fixed with screws complete all as specified and directed.

S&F of 40 mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, fancy type bright finished, complete all as specified and directed

S&F 20 mm dia stainless steel medium grade curtain rod medium grade steel with and including stainless and caps/knobs and stainless steel wall mounting brackets, complete all as specified and directed

S&F in replacement of stainless steel wire cloth 0.36 mm in nominal dia of wire average width of aperture 1.40 mm and fixed with steel beads to steel shutters or fixed with wooden beads to wooden joinery, in multi storey buildings, complete all as specified and directed

S&F of 3mm thick sheet glass ordinary quality glazing with oil putty or beads in square n. exc 0.5 Sqm in each pane complete all as specified and directed

S&F of 3mm thick figured glass pin headed glazing with oil putty or beads in square n. exc 0.5 Sqm in each pane complete all as specified and directed

S&F in replacement of stainless steel sink, 1.00 mm thick for kitchen with plug, with and including 40mm dia CP waste coupling, waste pipe of 750mm long, washers, cantilever brackets, connecting union etc overall approx size 550 mm x 450 mm with approx bowl size of 500 mm x 375 mm x 200 mm etc, complete all as specified and directed

S&F in replacement of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet (excluding flushing cistern and flush pipe) including lime concrete bedding, complete all as specified and directed

S&F in replacement of PVC connection 450mm long, 15mm dia PTMT (PVC), complete all as specified and directed

S&F in replacement of stainless steel kitchen plate rack made out of 1.00mm thick sheet of size 765x920mm and 220mm deep, weight not less than 7 Kg, complete all as specified and directed

M&L for medium grade galvanised steel water tubing with and including all fittings and fixtures, fixed to wall or laid in floors for 15 mm bore, concealed or exposed, complete all as specified and directed

M&L for medium grade galvanised steel water tubing with and including all fittings and fixtures, fixed to wall or laid in floors for 20 mm bore, concealed or exposed, complete all as specified and directed

M&L for cutting chases, pinning in for concealed water tubing, not exc 10 cm girth and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc complete all as specified and directed

S&F in replacement of bib tap, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all as specified and directed

S&F in replacement of long body bib tap, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all as specified and directed

S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, complete all as specified and directed

S&F in replacement of Stop cock with long shank and cup (concealed type), 15mm dia with wall flange, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe / unions, complete all as specified and directed

S&F in replacement of angular stop cock 15 mm dia with wall flange made of cast copper alloy, chromium plated fancy type, complete all as specified and directed

S&F in replacement of stainless steel grating of round shape of 150mm dia with hinge type openable jali with and including fixing in CM (1:4) to floor/nahani traps etc, complete all as specified and directed

Taking down eaves gutter and rain water pipes including all fittings any size and pattern complete all as specified and directed.

S&F of ring fit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and including rubber tighten gaskets, ring fit sockets etc, with and including all type of fitting i.e. tee, bend, junction etc, complete pipe duly laid in floor/trenches, complete all as specified and directed

S&F of ring fit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, Type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and including rubber tighten gaskets, ringfit sockets etc, with and including all type of fitting i.e. tee, bend, junction etc, complete pipe duly fixed to wall, complete all as specified and directed

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, complete all as specified and directed

M&L of water proofing treatment to roof slab with APP based modified polymeric membrane centre core 100mm micron HMHDPE outer film 20 micron each having thickness 3mm weight not less than 3kg/Sqm as per manufacturer’s instructions with torch applicationcomplete all as specified and directed by Engineer-in-Charge with following course of description below:- (a) 10 mm thick plaster in CM 1:4 with WPC will be applied over the roof slab when concrete is green. After the plaster is cured the roof will be tested for water tightness by ponding with water for seven days for any seepage is observed the rectification will be carried out by pressure grouting under the pressure of 5kg/sqcm using cement based cement grout. After the surface is repaireds the slab will be tested for water tightness again before proceeding with further treatment. (b) the surface of roof, parapet and gutters, drain mouths, etc. over which waterproofing treatment is to be applied shall be cleaned of all foreign matter such as, fungus, moss, dust etc by wire brushing and dusting. For cast iron drain out lets a grove shall be cut around to tuck in the treatment. Concrete angle-fillets shall be provided at junctions between roofs and vertical faces of walls (parapet and other walls) around obstacles such as pipes, chimney stacks, etc. and other similar situation to ease up about corners. (c) Bitumious based primer confiorming to IS: 3384 @ 0.3 kg/SM to be applied on prepared surface, till the surface is property. impregnated. (d) After the application of approved bituminous primer the water proofing membrane shall be laid on the primed surface by torch application method as per manufacturer's instruction. The overlap while toching shall be 100mm in longitudinal direction and 100 mm in transverse direction. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer and seling it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (e) All joints and changes in direction should be curved with cement mortar 1:3 mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane.

M&L for Apply a coat of bituminous aluminium paint @ 0.20 Kg/Sqm over APP membrance, complete all as specified and directed

M&L for Cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed; set jointed with grey cement and no pigment and pointed in neat cement slurry in floors, and cut and polished, complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) mixed with water proofing compound @ 0.20 Ltr/bags on roof surface/ vertical wall surface of sunken, when concrete is green, complete all as specified and directed. Note:- liquid WPC will be paid separately.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed.

M&L 75 mm thick cement concrete type C2 1:3:6 (using 40 mm graded stone agg) as in plinth protection and path laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface, complete all as specified and as directed. Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out,soft loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

FE-410 Gde Steel work in trusses, purlins post, gate etc including special shaped washer etc. complete using ERW or induction butt welded (framed), trussed, purlins, crane gantries, post,rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

M&L for sand filling under floor or in foundation including watering and consolidation etc complete all as specified and directed.

M&L Hardcore Broken stone or boulders of guage n.exc 63mm but n exc. 100 mm, deposited spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

M&L for 100mm th PCC 1:4:8 type D2 as in sub base of flooring complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in CM (1:6), complete all as specified and directed.

S&F of exposed frame false ceiling system with GI powder coated grid consisting of interlocking arrangement of main T runner of 15mm size, suspended at 1200mm C/C and cross T runner of 15mm size suspended at 600mm C/C supported by 1.5mm dia GI wire from roof/Slab/truss incl wall/perimeter runner/channel of 15 mm size with and incl 4mm thick pre-painted non asbestos fiber reinforced cement board (E-board), designer type of size 595x595mm, duly fixed in ceiling frame work, complete all as specified and directed.

Kota stone slab 20-25mm thick in riser of steps, skirting, dadoand pillar laid over and incl 10mm th cement screed base of CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

S&F of steel work in tubular trusses (round, retangular, square including gusset plate special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1998 grade St 240 complete all as specified and directed.

M&L for Cutting holes into 0r through brick walls built, in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime concrete and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and directed

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other to be fitted with washers and one hexagonal or square nuts complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary nut bolt ,reveting,gusset plate, welding for securing of stain steel pole and railing, accessories & stainless steel dash fasteners etc., of required size, on the top of floor or the side of waist slab with suitable arrangement,complete all as specified and directed.

M & L for Marble makrana white 20mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types and pointed in white or coloured cement to match as in flooring/tread over 15mm thick screed bed in CM 1:4.complete all as specified and directed.

M & L for 20mm thick marble machine cut in skirting/riser laid over cement screed and jointed with grey cement slurry including cutting and polishing of type and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc.complete all as specified and directed.

M&L for Point wiring with 1.5 Sqmm FRLS insulated, unsheathed, multistranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLS insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 18 SWG, with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with brass /GI screws for mounting switches, sockets, fan regulator, etc. complete all as specified and directed for the following points:-

One light/Bell point controlled by one switch

One ceiling fan controlled by one switch

One exhaust fan controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per Ser item No 193 above but with 4 sq mm FRLSH copper wire with 4 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on modular MCB protected plug and socket board complete all as specified and directed.

M&L for Circuit/submain wiring alongwith earth wire 2 runs x 6 sqmm + 1 run x 6 sqmm with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm concealed in wall/ floor etc complete all as specified and directed by Engineer-in-Charge. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

All as per Ser item No 195 above but 2runsX4 Sqmm +1runX4Sqmm complete all as specified and directed. Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length

Notes for item No. 193 to 196 (i) Quoted rate shall deemed to incude the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface. (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & caping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing caping may be used in that portion.

S&F, Switch piano type, single pole, one way, 6 amps, 240 volts, complete all as specified and directed.

S&F, Switch piano type, single pole, one way, 16 amps, 240 volts, complete all as specified and directed.

S&F, Socket, two-in-one, 5 pin, 6 Amp, universal type, 240 volts, complete all as specified and directed.

S&F, Socket, 6 pin, 6/16 Amp, multipurpose 240 volts, complete all as specified and directed.

S&F Bell push switch, single pole, one way, 6 Amps, 240 volts, complete all as specified and directed.

S&F electric bell of DINGDONG type, 240 volts, single pole and making all necessary connections, complete all as specified and directed.

S&F, angle holder, metal cased, bakelite body, 240 volts, complete all as specified and directed.

Supply and fix electronic fan regulator in 5 steps, 240V, 50Hz complete all as specified and directed.

S&F, Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed.

S & F 7W White LED retrofit lamp suitable for B-22 holder base with polycarbonate diffuser and aluminium heat sink complete all as specified and directed.

Supply and fix LED batten box type with CRCA sheet steel body pre-wired suitable for and including provision of 1x20 Watt (4 feet) retrofit LED tube with PC body and connecting up with twisted three core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix LED batten 9W/10W (2 Feet) complete with polycarbonate diffuser and built in with electronic driver including connecting up with twin core twisted flexible copper conductor cable form ceiling rose to connector of fitting complete all as specified and directed.

Supply and fix LED building security light fitting 25 watts with high efficiency long life LEDs with In-built electronic driver complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP 65degree of protection including GI pipe bracket made up of 25mm dia medium grade GI pipe of length 1.50m bent to required shape and fixing on walls with suitable MS clamps(02Nos) made up of 25mmx4mm MS flat, nuts, bolts and washers and provision of 3 core twisted flexible copper cable 0.5 sqmm from ceiling rose to connector of fitting complete all as specified and as directed.

Supply and fix in replacement of LED bulkhead luminaire in die-cast aluminium alloy body heat resistant prismatic glass cover, with specially designed gasket for minimum IP 55 degree of protection suitable for and including provision of 10W retrofit LED bulb, full white with B22 lamp holder complete all as specified and directed.

Supply and fix modular MCB protected plug and socket board in sheet steel enclosure with 25A rated mini MCB and 25A rated 3 pin plug, 240 V, 50 Hz complete including cutting the wall surfaces for flush mounting of socket board and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers with copper winding complete all as specified and directed.

Supply, installation & testing of Electric Water Heater storage type, vertical, 25 Liters capacity, minimum 5 Star rated, with heating element, PUF insulation, multifunction safety valve, adjustable knob for temparature setting and mild steel inner tank and outer body suitable for operating on 230V, 50 Hz, single phase AC supply including hot & cold water PVC connections and mounting on wall with suitable size & No. of anchor bolts complete all as specified and directed.

Supply and fix in replacement of MCCB / MCB distribution board, Vertical TPN, 4 way, 415 V, 3 phase, AC with MCCB as incomer and MCBs as outgoing in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface including taking down existing unserviceable MCB DB of any description complete all as specified and directed. Note: MCCB / MCBs shall be measured and paid separately.

Supply and fix MCB distribution board, SPN, 8 way 230 Volt in sheet steel powder painted enclosure double door type with IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separetely.

S& F MCCB TPN 100 Amp, 16 KA, 'C' curve, 415 V, 50 Hz complete all as specified and directed.

S& F MCB SPN 40 Amp, 10 KA, 'C' curve, 230 V, 50 Hz complete all as specified and directed.

All as per Ser item No 219 above but SP 6 to 32 Amp, 230 V complete all as specified and directed.

Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or strip and overall PVC sheathed, 16 sq. mm nominal cross section, 4 core in service connections as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc including taking down existing unserviceable service cable of any description complete all as specified and directed.

Material and labour for Double wall corrugated HDPE pipe, ISI marked of outer dia 50mm, inner dia 38mm with smooth internal and profiled external surface, non-pressure type, laid in trenches/floors/duct or fixed on walls /pole including all connections, accessories like socket, couplers, bends, etc for protection of LT cable XLPE grade 1100 volts complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for laying of GI Pipe and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including leveling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

M&L for Earthing complete with galvanised iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connecting to GI wire 4 dia mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electircal plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh,protection pipe, earth wire upto 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

M&L for Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 20mm bore complete all as specified and directed.

Supply and fix in replacement of Gun-metal, gate valves, with iron wheel head, screwed both ends for iron pipe ov sizes 20mm and fixed complete all as specified and directed.

Cutting and screwing of existing steel tubing for alterations or additions of size 40 or 50 mm done in position without taking down and inserting tee branch connection complete all as specified and directed.

Supply and fix in replacement of integrated LED batten 10 watt, 2 feet long, full white in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix in replacement of integrated LED batten 20 watt, 4 feet long, full white in Engineering plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply and fix in replacement of ventilating fan with plastic body with louvers, 250mm sweep, single phase, 230 volts, 50 Hz. including taking down existing unserviceable ventilating fan of any description complete all as specified and directed.

Supply and fix in replacment of MCB distribution board, SPN, 04 way in sheet steel powder painted enclosure double door type with minimum IP 43 degree of protection with built in copper bus bar, neutral link and earth link complete including cutting the wall surfaces for flush mounting of DB and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed. Note: MCBs shall be measured and paid separately.

S& Fin replacment of MCB TPN 63 Amp, 10 KA, 'C' curve, 415 V, 50 Hz complete all as specified and directed.

Taking down existing unserviceable service cable of any description and Supply and laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or strip and overall PVC sheathed, 16 sq. mm nominal cross section, 4 core in service connections as per IS 7098(Part 1) including connecting on LT OH line / LT panel /DB with suitable lugs, glands, binding wire etc complete all as specified and directed.

Supply and fix in replacement of Hot Press Molded SMC meter box of size not less than 700mm x 480mm x 210mm for accommodating 04 Nos of Single Phase energy meters including cutting the wall surfaces for flush mounting of meter box and making good with cement plaster, putty and paint to match with the existing surface all as specified and directed.

Taking down carefully the ceiling fan of any size 1200mm / 1400mm sweep, twin core cable and, dismantling fan blades and deposit to MES store Yard for servicing including supply and replacement of bearings/bushings, capacitor and terminal connector including filling cavities with filler, applying two coat of synthetic enamel spray paint of existing colour, suitable for any model of existing fan etc and incl writing MES No in figure and words in 25 mm wide by synthetic enamel paint of black colour on ceiling fan and Hanging ceiling fan in its existing or new location and connecting up including provision of desired cable from ceiling rose to connector of fan and testing for satisfactory functioning complete all as specified and directed. Note: (a) Rewinding if required shall be measured and paid separately. (b) The work is to be carried out in E/M store yard tto the entire satisfaction of Engr-in-Charge.

All as per Ser item No 237 above but of exhaust fan of any size up to 350mm sweep complete all as specified and directed. Note: Rewinding if required shall be measured and paid separately.

Material and labour for Rewinding of Ceiling Fan of size 1200mm / 1400mm sweep by shifting to workshop, cutting and removing of old burnt/damaged winding, cleaning of slots and other parts and rewinding the ceiling fan motor with super enameled copper winding wire of existing gauge with suitable class of insulation, applying varnish, heating, drying, assembling and testing for satisfactory performance complete all as specified and directed.

All as per Ser item No 239 above but exhaust fan of size up to 350mm sweep complete all as specified and directed.

M&L for Tubes, 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors of 20mm bore complete all as specified and derected.

Supply and fix in replacement of Gun-metal, gate valves, with iron wheel head, screwed both ends for iron pipe ov sizes 20mm and fixed complete all as specified and directed.

Cutting and screwing of existing steel tubing for alterations or additions of size 40 or 50 mm done in position without taking down and inserting tee branch connection complete all specified and directed.

M/S Ritu Tandon

M/s Jagdish Chandra Arora

UNIVERSAL ENGG CO

Flint India