752799 A ADDN ALTN CUM SPECIAL REPAIR TO OFFRS JCO ORs MD ACCN AT GOPALPUR MIL STN

Amount

SCHEDULE "A" :

Item No. 01 :- Demolition of cement concrete(unreinforced) in ground floor or paving not exc 15 cm thick(below or above Ground Level) complete all as specified and directed.

Item No. 02 :- Demolition of unreinforced cement concrete in ground floor, paving exc 15 cm thick complete all as specified and directed.

Item No 03 :- Dismantling floor, hearth or wall/roof tiles including cement mortar bedding (but not backing) and rubbish off the permises complete all as specified and directed.

Item No 04 :- Demolition of reinforcement cement concrete above ground floors n exc 15 cm thickness (Reinforcement cut as required to facilitate demolition) such as cooking platform, chajjas etc complete all as specified and directed.

Item No 05 : Post construction Anti termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

Item No 06 : All as per item No. 05 above but along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

Item No 07 : Post construction Anti termite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

Item No 08 : Post construction Anti termite Treatment for switch boards including removing the cover carefully and inserting adequate amount of chemical (powder) and closing the cover complete all as specified and directed.

Item No 09 : M&L for 10 mm thick Light shade coloured designer double charged vitrified ceramic tiles, not exceeding 0.36sqm, in floors etc over and including 15mm thick screed bed in CM 1:6 set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.

Item No 10 : M&L for 10 mm thick Light shade coloured designer double charged vitrified ceramic tiles, not exceeding 0.36sqm in vertical surface such as skirtings, dados etc over and including 10mm thick rendering in Cm 1:4 set & jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Item No 11 : - M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm in floors etc over and including 15mm thick screed bed in cement Mortar 1:6 set & jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed.

Item No 12 : - M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm in floors etc over and including 15mm thick screed bed in cement Mortar 1:6 set & jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed.

Item No. 13:- M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring, surface finished even and rough to receive the topping layer complete all as specified and directed.

Item No. 14:- M&L Prepolished (mirror finish) Machine cut kota stone slab flooring 18-20 mm thick as in risers, steps & skirting, over and including 10 mm thick screed bed in cement mortar 1:4 laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing & rounding to edges complete all as specified and direct (Kota stone should be single piece in tread and riser).

Item No. 15:- M&L for glazed ceramic coloured tiles 350x250x7mm/450 x 300 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including 10mm thick rendering in CM 1:4 complete all as specified and direct. Note- The size of tiles (except thickness) may be varied during execution without any price adjustment

Item No 16 :- BLANK

Item No 17 : - Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Item No. 18 :- M&L Brick work using fly ash bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Item No. 19 :- M&L Brick work using fly ash bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 in half brick thick wall complete all as specified and directed.

Item No 20:- M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base complete all as specified and directed.

Item No. 21 :- M & L 75 mm thick PCC 1:3:6 type C-1 using 20 mm graded aggregate as in plinth protection finish even & smooth without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling compreising of one part of heated bitumen 80/100 gde and three part of sand (all by weight) complete all as specified and directed.

Item No 22 : - M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span, coping, benching, bed block, lintel band, plinth courses etc and similar work including weathering,slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

Item No 23 : - M&L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab, chajjas, shelves and similar work including necessary form work and set in CM 1:4 complete all as specified and directed.

Item No 24 :.Taking down cement plaster any description on brick or stone walls, ceiling/roof etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Item No 25 : - M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surface of wall finish even and smooth with out using extra cement complete all as specified and directed.

Item No 26 : - M&L for rendering 15 mm thick in cement mortar 1:4 in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement of approved makes complete all as specified and directed.

Item No 27 : - M&L for rendering 5 mm thick in CM 1:3 on RCC ceiling surface and finished even and smooth without using extra cement complete all as specified and directed .

Item No 28 : - M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surface of wall in isolated width exc 15cm but not exc. 30cm and finished even and smooth without using extra cement complete all as specified and directed

Item No 29 - Supply only liquid water proofing compound, ISI marked omplete all as specified and directed.

Item No 30 - Taking down chowkats or frames with shutters not exc 1.5 Sqm each (with out taking off shutters from the frames) incl making good the disturbed portion complete all as specified and directed.

Item No 31 :- Taking down chowkats or frames exc 1.5 sqm but not exc 4.0 Sqm each with shutters ( with out taking off shutters from the frames) incl making good the disturbed portion complete all as specified and directed.

Item No 32 : - Taking down shutters of any description exc 1.00 Sqm but not exc 2.00 Sqm each and removing to store complete all as specified and directed.

Item No 33 : - Taking down and refixing in the same opening shutters of any description exc 1.00 Sqm but not exc 2.00 Sqm each after easing & adjusting complete all as specified and directed.

Item No 34 : M&L Second class hard wood(SAL) Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

Item No 35 : Cutting holes in brick walls exc half brick but not exc one brick built in cement mortor for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed.

Item No. 36 :- M&L Second class hard wood 35 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.24 (a) complete all as specified and directed.

Item No 37 : - S&F 35 mm thick second class hard wood rail and style plain framed factory made panelled shutter (two panel) with lock rail and panel of 9 mm BWP commerical ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Item No 38 : S&F factory made UPVC white colour sliding window three track made of extruded profiles with wall thickness of 2.3 mm (+0.2mm ). Window profile with hollow section with multi chamber, Frame (88 mm x 52 mm ), sliding sash (42 mm x 67 mm), sliding mesh sash (42mm x 57mm), sliding interlock (one vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5 mm x 16mm) will be mitered cut and fusion welded at all corners, including railing of holes for fixing of hardware and drainage of water etc, making arrangement for fixing of hardware, EPDM gasket, 1.2 + 0.2mm thick galvanised steel frame (30 mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware: (Touch Lock of Zinc alloyed (white powder coated), steel roller system, Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories.) (Note: The unit rate quoted by contractor shall include cost of glass and all other connected accessories)

Item No. 39 :- S&F 7 mm thick aluminium grills of make"Decogrill" model DG 104 surrounded by aluminium 'C' channel with mesh size 99 x 105mm complete all as specified and directed.

Item No. 41:- M&L for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings frame work of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Item No 42 : S&F Mild steel works as in hold fasts, clamps, plain angle cleats for securing purlins to woodtrusses or rafters, cooler stands and similar small articles conforming to Fe 410 - 0 or Fe310-0 complete all as specified and directed.

Item No 43 : S & F solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening complete all as specified and directed

Item No 44 : S&F Factory made solid PVC Moulded door shutter, 28 to 30 mm thick (stiles) with 2, 4, or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face and 2 mm plain colour PVC sheet on back face,with particle board core supplying and fixing in the frame as shown on drawing in section 8 of SSR-2020 Part-II complete all as specified and directed

Item No 45 : S&F 100 mm long Hasp and staple, aluminum anodised, wire type, including bolt to hinge plate and fixed with screws complete all as specified and directed

Item No 46 : S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed

Item No 47 : M&L butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised type B-21 for 100 mm long complete all as specified and directed.

Item No 48 : M&L butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised type C-22 for 75 mm long complete all as specified and directed.

Item No 49 : S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 300 mm length of bolt complete all as specified and directed.

Item No. 50 :- S&F aluminium, anodised, barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

Item No 51 : S&F extruded aluminium alloy handles fabricated type anodised of 150 mm size complete all as specified and directed.

Item No. 52 :- S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed.

Item No 53 : S&F mild steel, 300mm long ordinary helical door spring incl roller and roller plate fixed to any type of frame complete all as specified and directed.

Item No. 54 :- S&F in repair aluminium, anodised, barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

Item No 55 : S&F in repair aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 300 mm length of bolt complete all as specified and directed.

Item No 56 : S & F in repair butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised type B-21 for 100 mm long complete all as specified and directed.

Item No 57 : S&F in repair extruded aluminium alloy handles fabricated type anodised of 150 mm size complete all as specified and directed.

Item No. 58 :- S&F small fittings of second class hard wood door, window stops and the like not exc 200 cucm each including MS butt hinges, medium weight, cold rolled 50mm long all as specified and directed.

Item No 59 : S&F Aluminum alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Item No 60 : S&F in repair Aluminum alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified and directed.

Item No. 61 :- S&F in repairs 18/19 mm thick high density PVC / WPC solid fibre board with prelaminated PVC sheet as kitchen cupboard and frame including taking down the old cupboard shutters and removing to store complete all as specified and directed.

Item No. 62 :- S & F Continuous (piano) hinges, of brass, bright finish or electrogalvanised Width of flaps (when open) 40 mm complete all as specified and directed.

Item No. 63 :- S&F magnetic catcher with nut and screw of mild steel bright finish complete all as specified and directed.

Item No. 64 :- S&F 40 mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed.

Item No. 65 :- S&F in repair of stainless steel kitchen plate rack of size 750x750x250mm complete all as specified and directed.

Item No. 65A :- S&F in repair of stainless steel kitchen plate rack of size 600x750x250mm complete all as specified and directed.

Item No. 66 :- S&F CP Peg set of six of approved makes complete all as specified and directed.

Item No. 67 :- S & F in repair Stainless steel fancy type curtain rod 25 mm dia including end globe/ mountings as approved complete all as specified and directed.

Item No. 68 :- S&F SS curtain rod Bracket fancy type for curtain rod 25 mm dia of any colour as approved complete all as specified and directed.

Item No. 69 :- Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Item No. 70 :- Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

Item No. 71 :- Taking up or down steel tubing and connections including cleaning if refixing required for 25 mm bore of pipe complete all as specified and directed.

Item No. 72 :- M&L cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves,lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good in brick walls, cutting not exceeding 10 cm girth complete all as specified and directed.

Item No. 73 :- Supply & laying 15mm outer dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

Item No. 74 :- Supply & laying 20mm outer dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

Item No. 75 :- Supply & laying 25mm outer dia 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded Polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

Item No. 76 :- S&F in repair 15mm bore chromium plated central hole basin mixer single lever without popup waste system with 450 mm long braided hoses of approved makes complete all as specified and directed.

Item No. 77 :- S&F in repair chromium plated wall mixer 3- in - 1 system with provision of both hand shower and overhead shower complete with 115mm long bond pipe, connecting legs and wall flange (with hand shower) of approved makes complete all as specified and directed.

Item No. 78 :- S&F in repair vitreous china WHB size 550x400 mm white flat back including PVC waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etc. complete all as specified and directed.

Item No. 79 :- S&F LDPE pipe 50 mm of pressure rating 6kgf/sqcm fixed complete to walls, ceilings or in floors etc complete all as specified and directed.

Item No. 80 :- S&F in repair white vitreous china wash down water closet pan pedestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe of approved makes complete all as specified and directed.

Item No. 81 :- S&F in repair 10 litres capacity PVC valveless, syphonic action type low level flushing cistern ,white including flush pipe, cantilever brackets ,inlet, ball valve, float and handle, incl bracker and flush pipe of low level of 32 mm dia fixed to wall of approved makes complete all as specified and directed.

Item No. 82 :- S&F in repair chromium plated health faucet with 8mm dia and 1.2 m long flexible tubes and wall hook suitable for EWC including nut/washer complete all as specified and as directed.

Item No. 83 :- S&F PVC connection 15mm dia size and 450 mm long with 2 Nos check nuts its washers complete all as specified and directed. Make: Prayag

Item No. 86 :- S&F in repair bib tap 15 mm bore, chromium plated, fancy type long shank with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

Item No. 86A :- S&F in repair Pillar taps 15mm bore, cast copper alloy, with capstan heads,chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

Item No. 87:- S& F in repair CP brass tubular towel rail 20 mm dia D type 60 cm long between flanges complete all as specified and as directed.

Item No. 88 :- S&F in repair angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and directed.

Item No. 89 :- S& F in repair CP two way angle valve with wall flanges 15 mm bore, screwed down, screwed for iron pipe or for brass ferrule of approved makes complete all as specified and as directed.

Item No. 90 :- S&F in repair of stainless steel soap dish, of standard size and shape of approved makes complete all as specified and as directed.

Item No. 91 :- S&F in repair chromium plated toilet paper holder with flap complete all as specified and as directed.

Item No. 92 :- S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers and wastes & waste pipe incl bedding in cement mortar to dwarf wall or incl fixing suitable sizes of cantilever brackets and connecting union to pipe overall size 915 x 460 mm, bowl size 410 x 330 x 160 mm of approved makes complete all as specified and as directed.

Item No. 92A :- S&F in repair Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mmof approved makes complete all as specified and as directed.

Item No.93 :- S&F in repair chromium plated shower rose 125 mm size with CP arm 300mm long with swivel joint fixed to pipe etc complete all as specified and directed.

Item No. 94 :- S&F in repair Plastic water closet seat cover white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Item No. 95 :- S&F glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard and railing 60cm long complete all as specified and as directed.

Item No 96:-M&L for 18 mm thick granite (of any type) work (table rubbed and polished) in cooking platforms, steps, cills and like incl edge moulding and cutting holes for gas pipe fixed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl 15mm thick screed in CM 1:4 complete all as specified and directed.

Item No 96 A:-M&L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Item No. 97 :- Taking down eaves gutters and rain water pipes of any size or pattern including all fittings etc complete all as specified and directed.

Item No. 98 :- S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore of pipe etc complete all as specified and directed.

Item No. 99 :- S&F PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints, fixed to wall, complete all as specified and directed.

Item No. 100 :- S&F for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore of pipe etc complete all as specified and directed.

Item No. 101 :- S&F PVC (SWR) pipes 75 mm bore single socketed, in any length with rubber ring joints, fixed to wall, complete all as specified and directed.

Item No. 102 :- S&F stack clamps made out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nut and securing ends of stays to wall or roof for 110 mm bore of pipe complete all as specified and directed.

Item No. 103:- S&F stack clamps made out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nut and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and directed.

Item No. 104 :- S&F PVC (SWR) bends any radius of 110 mm bore without access door complete all as specified and directed.

Item No. 105 :- S&F PVC (SWR) bends any radius provided with access door of 110 mm dia complete all as specified and directed.

Item No 106:-S&F PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe complete all as specified and directed

Item No. 107 :- S&F PVC (SWR) bends any radius of 75 mm bore without access door complete all as specified and directed.

Item No. 108 :- S&F PVC (SWR) bends any radius of 75 mm bore with access door complete all as specified and directed.

Item No. 109 :- S&F PVC (SWR) branch pieces, single (equal or un equal) ordinary or inverted (spigot or socket type) or with parraled branches of 110 mm dia with access door complete all as specified and directed.

Item No. 110 :- S&F PVC (SWR) branch pieces, single (equal or un equal) ordinary or inverted (spigot or socket type) or with parraled branches of 75 mm bore with access door complete all as specified and directed.

Item No. 111:- S&F PVC (SWR) vent cowl 110 mm bore complete all as specified and directed.

Item No. 112:- S&F PVC (SWR) floor trap of diameter of outlet 75 mm, plain with grating including jointing with solvent cement complete all as specified and directed

Item No. 113 :- S&F PVC (SWR) 'P' trap for 110 mm dia etc complete all as specified and directed

Item No. 114 :- Dismantling water tanks of any description, capacity exc 250 and not exc 500 litres and removing from site complete all as specified and directed.

Item No. 115 :- Dismantling water tanks of any description, capacity exc 500 and not exc 1000 litres and removing from site complete all as specified and directed.

Item No. 116 :- S & F rotational moulded polyethylene water storage tank in white colour triple layer(cylindrical vertical with closed top) 500 litre capacity hoisted and fixed in position as per SSR Part-I complete all as specified and directed.

Item No. 117 :- S & F rotational moulded polyethylene water storage tank in white colour triple layer(cylindrical vertical with closed top)1000 litre capacity hoisted and fixed in position as per SSR Part-Icomplete all as specified and directed.

Item No. 118 :- S&F ball valves for 20 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed.

Item No. 119 :- S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both, screwed both ends for iron pipe complete all as specified and directed.

Item No. 120 :- S&F in repairs Gun metal, globe or gate valve with iron wheel head, 25 mm bore, screwed both, screwed both ends for iron pipe complete all as specified and directed.

Item No 121 :-M&L for preparation of new surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Item No. 122 :- M&L for preparation of new surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Item No 123 :-Removing old paint by paint removers or burning off by blow lamps and cleaning with scrapers, any number of coats, any width or girth complete all as specified and directed.

Item No. 124 :- M&L for preparation of old surfaces wooden based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint complete all as specified and directed.

Item No. 125 :- M&L for preparation of old surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint complete all as specified and directed.

Item No. 126 :- M&L for applying 2mm thick birla / Jk Putty in two layers on old wall surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed.

Item No. 127 :- M&L for preparation of newly plastered surfaces of wall & concrete and applying 2 mm thick wall care putty in two layers including preparation complete all as specified and directed.

Item No. 128 :- M&L for applying two coats of oil bound distemper on wall or concrete over a coat of primer on prepared surfaces including rubbing with sand paper complete all as specified and directed.

Item No. 129 :- M&L for applying 2 mm thick birla / Jk Putty in two layers on old ceiling surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed.

Item No. 130 :- M&L for preparation of newly plastered surfaces of ceiling and applying 2 mm thick wall care putty including preparation of new surface complete all as specified and directed.

Item No. 131 :- M&L applying two coats of oil bound distemper over a coat of primer on prepared surface of ceiling including rubbing with sand paper complete all as specified and directed.

Item No. 132 :- M&L for preparation of old decorated surfaces of walls by walls by washing, rubbing down and scrapping of distemper surfaces and applying two coats of white wash complete all as specified and directed.

Item No. 133:- M&L applying two coats of acrylic exterior weather proof emulsion paint over a coat of exterior primer on newly plastered wall surfaces/old decorated wall surfaces, in case of old decorated wall surfaces includes complete removal of existing wall finish of any type with wire brush, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc complete all as specified and directed.

Item No. 134 - Preparing surface of sunken slab and applying 15mm thick cement plaster 1:4 cement sand mortar with integral water proofing compound both on floor and wall. The surface shall then be cured and allowed to dry then applying Epoxy Resin coating polymer modified cementitious coating like brush bond of Fosroc, pidilite and Bostic as per manufacturer's instructions both on floor as well as on wall and sunken floor shall be filled with graded cinder complete all as specified and directed.

Item No. 135 :- Taking down existing roof treatment of any description incl cement plaster etc and cleaning the top surface, washing down etc. Prepared to receive water proofing treatment incl filling of cracks, groves etc in neat cement slurry complete all as specified and directed.

Item No 136 :- M&L for rendering 10mm thick in cement mortar 1:4 withliquid water proofing compound @200 ml per 50 kg cement finished even and fair complete all as specified and directed. (Waterproofing compound shall be measured and paid separately)

Item No 137 :- M &L water proofing treatment on "Non approachable / non accessible and approachable roof" surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer all as specified and directed:-.

(i) Applying a coat of oxidised bitumen based solvent primer conforming to IS 3384-1965 @ 0.3 Kg /Sqm complete all as specified and directed.

(ii) Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg / Sqm incl cleaning surfaces complete all as specified and directed.

(iii) Laying unrolled over the bitumen coated surface, polymetric water proofing membrane Hyperpals standard wt not less than 3 kg / Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction.

(iv) Applying two coats of bituminous aluminium paint @ 100 gm per sqm per coat including preparation complete all as specified and directed.

Item No. 138 :- M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in copings, padding, roof kerbs, or mud stops rounded or chamfered on edges including necessary form work complete all as specified and directed.

INTERNAL ELECTRIFICATION

Item No. 139 :- Taking down copper / aluminium point wiring (light, fan, bell, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendent, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed.

Item No. 140 :- Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN / Main Switch including old unserviceable MCCBs /MCBs, Isolators, etc and making good to disturbed surface all as specified and directed.

Item No. 141 :- Taking down carefully copper/aluminium Sub main wiring of any size from surface /concealed /existing conduit of any height and removing materials from site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

Item No. 142 :- Taking down carefully existing geyser of any capacity after disconnecting all necessary electric and water supply connections and deposit to MES store yard of AGE E/M complete all as specified and directed.

Item No. 143 :- Taking down existing ceiling/exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan and deposit to MES store yard of AGE E/M complete all as specified and directed.

Item No. 144 :- Taking down existing single phase electric energy meter of any capacity after disconnecting all necessary electrical connections and deposit to MES store yard of AGE E/M complete all as specified and directed.

Item No. 145 :- M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq mm(nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ivory colour including all accessories, heavy duty ISI marked, after chasing in wall/ceiling etc with GI sunken boxes 1.2mm thick, 60mm deep for housing switch socket etc duly covered with modular white cover plate with inner frame suitable for modular switches including PVC insulated multi stranded copper conductor 1.5 Sq mm(nominal area) single core FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chases and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One light point controlled by one, two way switch 5 Amps

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.

(e) One 3 pin 5 Amps switch outlet point controlled by one switch on independent board.

(f) One bell point controlled by one, bell push 5 Amps

Item No. 146 :- All as per item No 145 but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unshealthed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

Item No. 147 :- All as per item No 145 but using 4.0 sq mm single core copper conductor FRLS cable of multistranded PVC insulated unshealthed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 4.0 sq mm copper conductor FRLS cable as earth continuity conductor along with wiring and connecting to the common eath dolly. (for AC Point)

Item No. 148 :- M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq mm(nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ivory colour including all accessories, heavy duty ISI marked, after chasing in wall/ceiling etc incl anodised pressed steel sunken box for housing switch socket etc duly covered with white laminated 3mm thick hylam sheet cover including PVC insulated multi stranded copper conductor 1.5 Sq mm(nominal area) single core FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chases and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One light point controlled by one, two way switch 5 Amps

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.

(e) One 3 pin 5 Amps switch outlet point controlled by one switch on independent board.

(f) One bell point controlled by one, bell push 5 Amps

Item No. 149 :- All as per item No 148 but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unshealthed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

Item No. 150 :- S&F Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified.

Item No. 151 :- S&F Modular switch Piano flush type, single pole, one way, 5/6 amp single module complete all as specified and directed at site.

Item No. 152 :- S&F Modular switch Piano flush type, single pole, one way, 15/16 amp single module complete all as specified and directed at site.

Item No. 153 :- S&F Modular switch Piano flush type, single pole, two way, 5/6 amp single module complete all as specified and directed at site.

Item No. 154 :- S&F Modular socket outlet multipurpose having provision for 3 pin, 5/6 amp and 2 pin, 5/6 amp, 2 module piano flush type complete all as specified and directed at site.

Item No. 155 :- S&F Modular socket outlet multipurpose having provision for 3 pin, 15/16 amp and 3 pin, 5/6 amp, 2 module piano flush type complete all as specified and directed at site.

Item No. 156 :- S&F modular step type electronic fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and directed at site.

Item No. 157 :- S&F Bell Push modular 6 amps single module complete all as specified and directed.

Item No. 158 :- S & F Switch Piano type single pole 5 amp, 230 Volts complete all as specified and directed at site.

Item No. 159 :- S & F Switch Piano type single pole 15 amp, 230 Volts complete all as specified and directed at site.

Item No. 160 :- S & F Switch Piano type 2 way switch 5 amp, 230 Volts complete all as specified and directed at site.

Item No. 161 :- S & F switch bell push piano type 5 amp, 230 Volts Complete all as specified and directed at site.

Item No. 162 :- S & F socket outlet 2 in 1 , 5 pin, 5 amp, 230 Volts complete all as specified and directed at site.

Item No. 163 :- S & F socket outlet 2 in 1 , 5 pin, 5/15 amp, 230 Volts complete all as specified and directed at site.

Item No. 164 :- S & F stepped type electronic fan regulator flushType complete all as specified and directed at site.

Item No. 165 :- S&F lamp holder, PVC/ Polycarbonate type with back plate suitable for batten / slanting fittings complete all as specified and directed.

Item No. 166 :- S&F Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ AC supply complete all as specified and directed.

Item No. 167 :- S&F for Modular type TV socket out let complete all as specified and directed.

Item No. 168 :- M&L for Sub main wiring with approved colour as per IS with four single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sqmm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc two runs of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and direced. (Note:- four runs of 6 sqmm cable, two run of 6 sqmm cable and one run of PVC conduit will be measured as one unit)

Item No. 169 :- M&L for Sub main wiring with approved colour as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sqmm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one runs of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and direced. (Note:- two runs of 6 sqmm cable, one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit)

Item No. 170 :- S&F Sheet metal enclosure MCB DB TPN 4 way Vertical type with 200 Amps rated bus bar 415 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonry etc and making good of disturbed surface to match with existing colour of wall complete all as specified and directed.

Item No. 171 :- S&F Sheet metal enclosure MCB DB SPN 8 way Vertical type with 200 Amps rated bus bar 240 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonry etc and making good of disturbed surface to match with existing colour of wall complete all as specified and directed.

Item No. 172 :- S&F MCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Item No. 173 :- S&F MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Item No. 174 :- S&F MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

Item No. 175 :- S&F Metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and directed.

Item No. 176 :- S&F water heater storage type (Geyser) vertical/Horizental type as per site requirement with inner container of capacity 25 ltrs, electrically operated, AC 230 Volts, BEE 5 star rated, ISI marked including 04 Nos of hold fechner nuts required suitable size fixed in brick wall, PVC connection pipe hot & cold complete all as specified and directed.

Item No. 177 :- S&F ceiling fan, 230 volts, 1200 mm sweep with main air delivery 210 CFM, service value of fan shall be greater than 6.1 as per BIS, with blades, down rod & other necessary accessories with brushless direct current motor(BLDC) incl provn of flexible cable from ceiling rose to fan terminal incl writting MES No. with synthetic enamel paint complete all as specified and directed.

Item No. 178 :- S & F for Energy efficient exhaust fan of 300 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 Cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick for fan base complete all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed included in quoted rate).

Item No. 179 :- Fixing only for ceiling fan, of 300 mm sweep including provision of PVC flexible copper cable of size 23/0.0076 three core from ceiling rose to fan for connection incl two coats of spray painting after cleaning & filling cavities with filler & writting MES No. with synthetic enamel paint complete all as specified and directed.

Item No. 180 :- S&F Highly efficient LED Bulbs, 10 W, used as a ready replacement for existing GLS/CFL diect fir lamp, in B-22 cap of make Bajaj, Havells, HPL complete all as specified and directed.

Item No. 181 :- S&F Decorative wall mounted luminaire made out of polycarbonate with unbreakable globe suitable for LED bulb and provision of LED bulb 10 Watts complete all as specified and directed. Make:- Havells Cat Part No LHDLO6160099 or its equivalent in specified make.

Item No. 182 :- S&F LED 10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed. Make:- Bajaj Cat Part No BCLSB 10 NW or its equivalent in specified make.

Item No. 183 :- S & F Energy saving new generation 10 Watts LED bulk head fitting IP-65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 form ceiling rose to fitting complete all as specified and directed. Make:- Bajaj Cat Part No BIBWP 10W LED or its equivalent in specified make.

Item No. 184 :- S & F wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen etc with warranty option of 5 years from date of installation complete with all accessories internally pre-wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make:- Bajaj Cat Part No BCLAB 20 W WH LED P, Wipro Cat Part No. LL20-281-XXX065-ALI or its equivalent in specified make.

Item No. 185 :- S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounting arrangements with warranty option of 5 years from date of installation/completion and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer-in-charge. Make :- Bajaj Cat Part No ENXT P 24L WH CR PC SD or its equivalent in specified make.

Item No. 186 :- S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/Ivory colour and its accessories heacy duty ISI marked of size 20 mm dia for LAN, telephone and TV connections including cutting. chasses and making good distrubed surface to match with existing finish with plaster complete all as specified and directed.

Item No 187 :Supply, installation, commisssioning and testing indoor type LT wall mounting Panel board of minimum size 1.50m (height x 1.20 m (breath) x 0.30m (depth) factory made CPRI approval panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of four Nos Three phase KWH meter, one No single phase meter and MCB TPN and providing glass view for reading of meter and providing rubber/PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/sleeves with maintained the colour code and copper strip/ wire busbar of suitable size to MCCB input and MCCB/MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of Powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 10 sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as specified and directed by Engineer - in - charge. (for officers G+1 Md Accn)

OUTGOING (a) MCB, Tripple pole & neutral, 40 amps, 415 volts, 'C' curve, 10 KA complete as specified and directed - 4 Nos (Officers ACCn) (b) MCB, single pole & neutral, 10 amps, 415 volts, 'C' curve, 10 KA complete as specified and directed - 1 Nos (Stair case lighting) (c) Smart Three Phase Meter AC Three Phase Four Wire, Tamper Proof, Static Meter of class 1.0, 415 V, 50Hz, 10A-60A conforming to IS 16444 and relevant IEC standard with inbuilt 865-867 MHz radio frequency communication facility with self healing mesh network with default and on demand display, billing data generation faciliy, antitamper features, Microprocessor and LED/LCD based circuitry, Meter should support the following data: 30 min instantaneous data for voltage, current, power factor, power, cumulative energy and frequency, 30 load survey data for energy, monthly billing survey for cumulative energy and Max demand. Meter should have connect/disconnect functionality operable compactable system from prepaid billing software in future. The meter should suppot open communication protocol DLMS with the software- 04 Nos (Make:Secure, L&T, Schneider, HPL)

Item No 188 :Supply, installation, commisssioning and testing indoor type LT wall mounting Panel board of minimum size 1.20m (height x 1.20 m (breath) x 0.30m (depth) factory made CPRI approval panel, weather, dust & vermin proof indoor, double door, front openable, including four comparment for fixing of four Nos Three phase KWH meter, one No single phase meter and MCB TPN and providing glass view for reading of meter and providing rubber/PVC gasket of suitable size all sides of door, with copper busbar wrapped with PVC tape/sleeves with maintained the colour code and copper strip/ wire busbar of suitable size to MCCB input and MCCB/MCB output of suitable length for connection of cable from main busbar, made out of 2.00 mm thick mild steel CRCA sheet with suitable size angle iron supporting frame including applying two coats of Powder coated paint over a coat of red oxide zinc chrome primer over exposed external & internal surfaces suitable for 3 phase 4 wire system 415/440 volts grade including complete internal wiring with 10 sqmm copper wire and connections of all outgoing / incomming existing cable of any size complete all as specified and directed by Engineer - in - charge. (for G+1 JCOs, OR Md Accn)

OUTGOING (a) MCB, Single pole & neutral, 40 amps, 240 volts, 'C' curve, 10 KA complete as specified and directed - 4 Nos (Officers ACCn) (b) Smart Single Phase Meter AC Single Phase two Wire, Tamper Proof, Static Meter of class 1.0, 240 V, 50Hz, 10A-60A conforming to IS 16444 and relevant IEC standard with inbuilt 865-867 MHz radio frequency communication facility with self healing mesh network with default and on demand display, billing data generation faciliy, antitamper features, Microprocessor and LED/LCD based circuitry, Meter should support the following data: 30 min instantaneous data for voltage, current, power factor, power, cumulative energy and frequency, 30 load survey data for energy, monthly billing survey for cumulative energy and Max demand. Meter should have connect/disconnect functionality operable compactable system from prepaid billing software in future. The meter should suppot open communication protocol DLMS with the software- 04 Nos (Make:Secure, L&T, Schneider, HPL)

Item No. 189 :- M & L for Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4 mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR Part-I including excavation and earthwork in any type of soil / strata and testing on completion. Note:- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

SCHEDULE "A" (Schedule of credit) Schedule of Credit Rs 427432.00 (Minus) inserted by the MES. (Note : Credit amount shall be deducted manually to arrive net bid amount)

M/s Bapujee Builders and Traders

V.Venkata Ramaiah

ANIL KUMAR BISWAL