SPECIAL REPAIRS TO COMMUNITY HALL AT DAD RESIDENTIAL COMPLEX, LEKHANAGAR UNDER GE NASHIKROAD CAMP

Amount

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc.

Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 using old size bricks.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level).

Providing cement concrete 1:4:8 type D2 (40 mm graded aggregate) in foundations, filling, sub bases etc.

Dismantling structural steel work including doors, gates but excluding framed truss etc

Framed work such as ornamental grills, gratings, etc. framed balusters; railings etc. including malleable cast iron work (for design as approved by Engineer-in-Charge) with ends of bars shouldered and/or riveted, or forged into spikes.

Two coat of synthetic enamel paint including one coat of red oxide primer on new/untreated steel or iron surfaces of any description over 10cm width or girth including preparation of surface.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

Rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces finished even and smooth without using extra cement.

Rendering 15mm thick in cement mortar 1:3 mixed with water proofing compound on faces of brick work or concrete surfaces finished even and smooth without using extra cement.

Supply only liquid water proofing compound.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises .

M&L glazed cermic tiles coloured size 350x250x7mm thick in vertical surface, set and jointed in neat cement slurry & pointed with coloured cement to match laid over and including rendering 10mm thick in CM 1:4 as in backing coat on fair surfaces of brick wall

M&L double charged vitrified ceramic digital tiles 10mm thick(square/ rectangular) polished, area of each tiles not exc 0.36 Sqm in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match including Screed bed or bedding layer of mortar 15mm thick for laying floor finishes cement plaster 1:6 complete all as specified and directed

M&L double charged Vitrified Ceramic digital tiles 10 mm thick (square/ rectangular) polished in skirting etc. cut out of tiles of area not exceeding 0.36 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including rendering 10mm thick in CM 1:4 as in backing coat on fair surfaces of brick wall

Non - skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. laid over and including 15mm thick cement mortar screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match.

Demolition of stone slabs & tiles of any decsription or thickness in floors, aprons etc laid, bedded & pointed in any mortar.all as specified and directed.

M&L Granite (Telephonic black/Ruby red) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite 18 to 20mm thick. all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations. (Stone slabs so provided shall be not less than 900mm in length)

Vitreous China water closet squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete including provision of lime concrete bedding fixed in repairs.

Vitreous China wash basinswhite, flat back, size 550 X 400mm, including cutting for and pinning in ends of brackets or erecting stand and waste coupling 32mm of PTMT (Minimum weight 45gms) half or full threaded fixed in repairs.

PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including flush pipe and brackets fixed in repairs.

Cast iron nahani trap 75mm dia of outlet, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

Taking up or down steel tubing and connections 15mm bore.

Taking up or down steel tubing and connections 20mm bore.

Refixing old steel tubing and connections 15mm bore in new or old position (Walls, ceiling, floors, etc.)

Refixing old steel tubing and connections 20mm bore in new or old position (Walls, ceiling, floors, etc.)

15mm bore galvanised steel water tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors.

20mm bore galvanised steel water tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors.

15mm bore bib taps, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.

15mm bore stop valves, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

15mm bore stop valves, cast copper alloy, fancy type, chromium plated (angle type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S&F in repairs chromium Plated cast copper alloy pillar tap with capston heads fancy type fixed to iron pipes 15mm dia..

PVC connections 15mm size with PTMT nuts of length 450mm

Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges.

S&F 8mm thick glass shelf "Corner" type size 300mm x300mm including necessary brackets front edge of glass rounded and woulded with CP railing complete, fixed in repairs .

Dismantling of PVC rain/vent/waste pipe any bore

S&F PVC (SWR) bends, any radius 110 mm bore with oval access door complete all as specified and directed.

S&F PVC (SWR) branch piece, double (double Y) equal or unequal 110 mm bore with access door all as specified and directed.

S&F PVC (SWR) junction (single 'T') equal or unequal, bore 110 mm with access door, complete all as specified and directed.

S&F PVC (SWR) pipe single socketed 110 mm bore, any in length with rubber ring joints fixed to walls complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sq. m but n exc 4 sq. m each.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) n exc 1.5 sqm each.

S and F 2nd class hardwood plain, solid,straight, chowkhats & frames, wrought,framed, rebated on the solid,rounded or champered,put togetherwith glue pinned at joints , supplied and fixed.

S&F hold fasts confirming to FE-290 Gde E165.

Preparing the surfaces of wood and wood based material,steel and iron work, new or old and treated with tar or coal tar black paint treating ends of pasts, backs of chowkhats etc area tarred exc 0.1 Sqm each.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MS suquare tube, suppling and fixing in opening as per specification and drawings .

S&F Factory Made Solid PVC Moulded Door Shutter, with particle board core 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face and as directed by Engineer in-charge.

150mm size aluminium handles, cast type, anodised.

150mm size aluminium anodised, barrel tower bolts of extruded section and fixed.

250mm size aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21.

Blank

Blank

Blank

S&F powder coated aluminium frame for doors , window , ventilators with one or more rebates including joining cleat for fixing etc complete all as specified ( Minimum thickness of powder coating 50 micron.) complete all as specified and directed.

S&F powder coated aluminium window, ventilators shutters sliding/fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary jioning cleats , glazing clips, rubber packing anodised aluminium snap beading , screws etc complete all as specified ( Minimum thickness of powder coating 50 micron.) complete all as specified and directed.

Aluminium (minimum 50 micron powder coated) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified.

M&L for 5.00mm thick sheet glass, ordinary quality and glazing in Aluminium window and frames as specified and directed.

S&F stainless steel wire cloth 0.36mm normial dia of wire and avg width of aperture 1.40mm and fixed with and incl nut and bolts or fillets etc to window or doors complete all as specified and directed.

Dismantling water tanks exc 250 & n exc 500ltr capacity.

Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 litre capacity, hoisted and fixed in position all as specified.

Ball valves, 20mm bore high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 2 1 0 gms.) fixed in repairs.

M&L prepration of old decorated plastered surfaces incl brooming down moulds & efforecent salt and trading oil and greasy spots and applying one coat of white washing on walls

M&L prepration of old decorated plastered surfaces incl brooming down moulds & efforecent salt and trading oil and greasy spots and applying one coat of white washing on ceilings

Complete removal of existing treatment of old decorated surfaces on walls.

Complete removal of existing treatment of old decorated surfaces on ceiling.

M&L 3mm thick Exterior wall care putty on walls.

M&L 3mm thick wall care putty on walls.

M&L3mm thick wall care putty on ceiling.

M&L Two coats of distemper oil emulsion on walls, white or tinted.

M&L Two coats of distemper oil emulsion on ceiling, white or tinted.

M&L Two coat of exetior emulsion paint (apex/weathercoat) on walls and ceiling plastered or unplastered surfaces over one coat of primer including preparing by brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots; removing nails, making good holes, cracks etc. by filling with putty.

M&L for prepration of old painted wooden surface of any description not other wise described exc 10 cm width or grith and applying two coat of synthetic enamel paint complete all as specified and directed.

M&L for prepration of old painted steel surface of any description not other wise described exc 10 cm width or grith and applying two coat of synthetic enamel paint complete all as specified and directed.

Taking down carefully existing bitumenous membrane/tarfelt treatment any description and cleaning and making good damaged surface in cement mortar 1:4 where ever required to make surface ready to receive fresh water proofing treatment on roof and flashing and junctions of parapet, kerb, wall etc. and removing rubbish out of defence land.

Demolition of concrete (unreinforced) of any description and in any position not otherwise specifically provided for.

Providing, cement concrete type B0 1:2:4 (12.5mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges.

Providing, cement concrete type B1 1:2:4 (20 mm graded aggregate) in steps, parapets and copings, kneelers, bases for water tanks, bed plates and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary formwork.

Waterproofing on roof including flashing and junctions of parapet, kerb, wall etc. as under:- (a) Applying bituminous primer on cleaned and dried surface @ 0.20 Kg/Sqm. (b) A coat of hot blown type bitumen of grade 85/25, applied hot at the rate of 2.25 kg/sqm. (c) Laying on primed surface by thermo fusion (torch application) 3mm thick APP based polymeric water proofing membrane weighing not less than 3.50kg/sqm and reinforced with polyester non woven fabric (not less than 150 gms/sqm). (d) Painting the exposed APP membrane surface with bituminous aluminium paint @ 0.15 Kg/Sqm.

S&F in repair stainless steel drapery rod dia not less than 25mm and weight not less than 0.350Kg per RM, complete all as specified and directed.

S & F stainless steel brackets made out of 10mmx2mm for fixing of drapery rod in wall including necessary fixing arrangement and stainless steel screw for holding drapery rod complete all as specified and directed.

S & F stainless steel stud for drapery rod of pattern as approved, suitable for drapery rods of 25 mm dia including screw for fixing complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, GI/aluminium grid etc.

S&F interlocking aluminium powder coated snap grid consists of main Tee runners of size 38mm x 25mm x 1.00mm spaced 1200mm centre to centre and cross Tee of size 25mm x 25mm x 1.00mm, 1200 long spaced between the main Tee at 600mm centre to centre to forma grid of 1200mm x 600mm and provide a secondary cross Tee 25mm x 25mm x 1.4mm (of lenght 600mm) to be interlocked of the centre of 1200mm x 600mm panel to form a grid of 600mm x 600mm and wall angle 25mm x 25mm x 1.5mm. Aluminium alloy extrubed section shall be aluminium anodized (minimum 15 micron) and shall conform to IS 733, IS 1285 and IS 737, and providing and fixing with Hangers of 4mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long size of grid 600 x 600mm complete all as specified and S&F non asbestos cement building board 4mm thick of make E board classic of M/s Everest Industries Ltd or equivalent make as approved, 'in ceiling fixed with screw as per manufacturer instruction".

Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete

Preparing new or untreated steel or iron surfaces over 10 cm width or girth and two coats of synthetic enamel paint over red oxide primer.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting, bldg. security light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc.

Taking down carefully by unscrewing from board/outlet boxes, fixture and fittings such as switches, sockets, ceiling roses, lamp holders, bracket, ceiling fitting, bulk head fittings, tube light fittings etc. for reuse at site or carrying to the store (To be measured only when found serviceable in all respects complete for reuse)

Taking down carefully sub main wiring of any size and type, and making good disturbed surfaces of walls, floors etc.

Taking down existing serviceable / unserviceable main switches / DB,s of any make and type including any type of boards etc. for reuse at site or carrying to the store (To be measured only when found serviceable in all respects complete for reuse) complete all as specified and directed.

Material and labour for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 4.0 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC casing & caping / conduit and accessories surface on wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for PVC casing & caping and IS:3419:1976 for accessories), with mild steel/pressed steel sunken boxes with earth dolly duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets etc, including PVC insulated multi-stranded copper conductor 2.5 Sq mm nominal cross sectional area single core cable as earth continuity conductor to common earth and connecting to earth dolly complee all as specified and directed at site for the one 3/5 pin 15/16 amps socket outlet independent.

Material and labour for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC casing & caping and accessories surface on wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for PVC casing & caping and IS:3419:1976 for accessories), with mild steel/pressed steel sunken boxes( with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally, and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed at site for the following :-

One light point controlled by one 5/6 amps one way switch

One ceiling fan point controlled by one switch and one fan regulator.

One exhaust fan point controlled by one switch.

One 3 pin socket outlet, 5 Amps on the same board with other switches.

One 3 pin socket outlet, 5 Amps independent.

Supply and fixing switch piano; flush type, single pole, one way, and 5/6 Amp IS: 3854 marked with valid CML No. complete all as specified.

Supply and fixing socket outlet multipurpose having provision for 3 pin, 5 Amp and 2 pin, 5 Amp, piano flush type IS: 1239-1988 marked with valid CML No complete all as specified.

Supply and fixing switch socket combination 2 in 1, 5 Amp flush type.

Supply and fixing switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal, IS: 1239-1988 marked with valid CML No complete all as specified.

Supply and fixing ceiling rose, Three terminal ISI marked surface bakelite suitable for batten fitting complete all as specified

Supply & fix LED tube light fitting, durable batten with decorative end caps (Make-Crompton, TRIM LINEA, Cat ref. LCTL-18-CDL or eqvt. make of Philips / Havells) complete all as specified and directed.

Supply & fix RETRO LED T5 (T5 LED Tubelight with PC body), (Make-Crompton, Cat Ref. LT5RT1-18-CDL or eqvt. make of Philips / Havells) complete all as specified and directed.

Supply and fix LED security / street light fitting highly effective and efficient lighting solution to street light application with thermal management, (Make-Crompton, ASTRA, Cat Ref. LSTS-18-CDL or eqvt. make of Philips / Havells) complete all as specified and directed.

Supply and fix LED bathroom light fitting, (Make-Crompton, STUD, Cat Ref. LBHP-10-CDL or eqvt. make of Philips / Havells) complete all as specified and directed.

Supply and fix LED Aura I pairs super bright LED's with highly efficient light-smoothing optics to deliver superior illumination and energy savings year after year light fitting, (Make-Crompton, AURA I, Cat Ref. LCPL-36-CDL(2X2) or eqvt. make of Philips / Havells) complete all as specified and directed.

Supply and fix flood light fitting LED for efficient high output LED for better distribution (Make-Crompton, AURA I, Cat Ref. LFLE-50-CDL or eqvt. make of Philips / Havells) complete all as specified and directed.

Supply & fix lamp holder, PVC / Polycarbonate type with back plate suitable for batten / angle fittings

Supply & fix LED bulb 7/10 W

Taking down fan of any size, sealing cable end, dismentalling blades and removing fan and blades to stoe

Taking down regulator, sealing cable end, dismentalling blades and removing regulators to store

M&L Painting of ceiling fans complete, in situ with synthetic enamel paint by spaying including filling cavities with filler, one coat after cleaning all dust etc.

Hanging only ceiling fan of any size removed against item no 17, connecting up complete with and including three core flexible PVC insulated multi stranded copper conductor of size 0.5 Sq mm from ceiling rose/ connector to fan.

Supply & fix stepped type electronic fan regulator flush type 240 vols, ISI marked with valid CML No.and connecting up complete on the existing phenolic laminated sheet etc. as required.

Supply and fix distribution board double door, for mounting MCBs, isolator, ELCBs etc factory made, confirming to IS: 8623-1&3, IEC 61439-1&3 fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral link and 200 Amps rated bus bar. DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of same make as MCBs /Isolator. DB shall also be provided with label marking indicating the incoming and outgoing circuits on all way as specified. The DBs shall be of IK 09, IP 43 protection class for the followings :

MCB DB SPN 4 Way, Double door, 240V (Make-L&T, Cat Ref. DBSPN004DD, or eqvt make of Legrand / Havells)

MCB DB TPN 4 Way, double door, 415V (Make-L&T, Cat Ref. DBTPE004DD, or eqvt make of Legrand / Havells)

S & F MCB SPN / TPN B-Curve complete all as specified for following ratings.

MCB SPN , 240 volt, 6/32 Amp (Make-L&T, Cat Ref. BB20320B, or eqvt make of Legrand / Havells)

MCB TPN, 415 Volt, 40/63Amp (Make-L&T, Cat Ref. BB40630B, or eqvt make of Legrand / Havells)

S & F MCB, 240 Volt single pole, breaking capacity 10KA with B-Curve 6 - 32 Amp (Make-L&T, Cat Ref. BB10160B, or eqvt make of Legrand / Havells) complete all as specified

Material and labour for sub main wiringTwo runs of 6 Sq mm as current carrying conductor and one run of 4.0 Sq mm as earth conductor with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core PVC insulated FRLS cable 1100V unsheathed with stranded copper conductor of nominal cross section area as under and drawing into and including PVC non metallic rigid conduit, accessories,of medium grade not less than 25mm dia ,including PVC insulated stranded copper conductor nominal cross section area as under of continuous earth wire complete all as specified.

Material and labour for earthing complete with galvanized steel plate electrode 60 cm x 60 cm x 6 mm surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25 meter below ground level with top edge of the earth plate at a depth of not less than 1.50 meter below ground level connected to galvanized iron or steel earth wire, 4.0 mm dia (No. 8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron, earth wire protected by galvanized steel pipe 15 mm dia (Light grade) & connected to main switch or main control board all as shown in electrical plate No. 5 of SSR-1991 Part I & including necessary excavation and earth work. The rate also include charcoal and salt in alternate layers 20 mm dia pipe (Light grade) for watering, protection pipe, funnel, wire mesh, PCC chamber in cement concrete (1:3:6) type C-I, 40 mm thick RCC (1:2:4) type B-1 cover and CI frame etc.

Fabricate,supply & fix GI pipe bracket 25mm dia - 0.9m long & 2 set of clamps made out of 30 x 5mm ms flat & fixed with anchor bolt suitable for security light fitting complete all as specified and directed.

Fixing only in repaires and connecting electric meter upto 25 amps complete all as specified and directed.

Labour only for fixing in repairs existing sub main wiring power/circuit using PVC insulated unsheathed, stranded copper conductor cable 2 single core of size 6 sqmm, earth continuity conductor of size 4 sqmm to be drawn through and including PVC casing caping / conduit not less then 32 mm dia medium grade fixed on walls/roof/floors all as specified and directed. (Note : Two wires of 6 sqmm and one wire of 4 sqmm and one run of PVC casing caping / conduit shall be measured as one unit).

M/s. SHRI SAINATH ENTERPRISES

Alpha Construction

SHILPVED

M/S GURBAX AND CO

JEET CONSTRUCTIONS CO.

Vinod Enterprises

M/S K. K. Construction