PROVN OF ANTI EROSON MEASURE NEAR B OFFR MESS AREA AND PROVN OF DRYING SHED AT DHOBI GHATOF AT RMS

Amount

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified

Excavation over area n. exc 1.50 m deep and getting out in soft / loose soil complete all as specified and as directed.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.50m in depth n. exc 10 sqm on plan and getting out in soft/ loose soil ,complete all as specified and as directed.

Returning, filling soil in trenches including spreading levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and as directed.

Removing excavated soil not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point all as specified and as directed.

M&L for hard core of broken boulder or stone of gauge not exc 63 mm deposited , spread and levelled in layers n.exc 15cm thick watered and rammed to true surfaces complete all as specified and as directed.

M&L Loose filling with Broken stone or boulders aggregates of gauge 80 to 150 mm in weep holes of retaining wall, complete all as specified and directed.

M&L for P.C.C 1:4:8 type D-2 (using 40 mm graded stone aggregate) in foundation,filling and mass concrete all as specified and directed

M&L for P.C.C 1:3:6 type C-2 (using 40 mm graded stone aggregate) in foundation,filling and mass concrete all as specified and directed

M & L for PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in for coping, hounching and the similar work, weathering slightly rounded or chamfered edges and throating including form work all as specified and diected.

M&L for Reinforced cement concrete, M-25 design mix (Using 20 mm graded stone aggregate ) as in footings, foundation including rafts, foundation beam, plinth beames; base for column etc ,basement slabs, under-reamed piles and mass concrete, complete all as specified and directed

M&L for Reinforced cement concrete, M-25 design mix (Using 20 mm graded stone aggregate ) as in columns, pillars, piers etc. complete all as specified and as directed.

M&L for Reinforced cement concrete, M-25 design mix (Using 20 mm graded stone aggregate ) as in beams, cantilevers, bressummers, lintels over 1.5 m span, complete all as specified and as directed.

M&L for Reinforced cement concrete, M-25 design mix (Using 20 mm graded stone aggregate ) as in as in slab supported on walls , beames and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc.complete all as specified and as directed.

M&L for Reinforced cement concrete, M-25 design mix (Using 20 mm graded stone aggregate ) as in Chajjas, complete all as specified and as directed.

M&L for pre-cast cement concrete 1:3:6 type C-1(using 20mm graded aggregate) as in kerb/ bond stone and set in cement mortar 1:4 including necessary from work and mould complete all as specified and as directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits for foundation and plinth beams and similar work for rough finished surfaces of concrete, complete all as specified and directed

M&L for form work to sides of pillars, posts, sturts, piers, columns and similar work etc for rough finished square, rectangular or polygonal surfaces of concrete complete as specified and directed.

Use and waste of formwork to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick , rough finished surfaces of concrete, flate, complete all as specified and directecd.

Use and waste of formwork to sides and soffits of floor or roof beam , lintels, cantilever, shelves ,flate, rough finished surfaces of concrete, complete all as directed.

Use and waste of form work to soffits of chullah hoods, chajjas, troughs and similar items flat, rough finished surfaces of concrete complete all as directed.

M&L for brick work with sub class ‘B’ bricks , straight or curved on plan exc 6 metre mean radius as in full brick thick walls built in CM(1:6) using old size bricks complete all as specified and as directed.

M&L for brick wrok with sub-class 'B' bricks, straight or curved on plan to any radius, built in CM (1:4) using old size bricks in half brick thick walls complete all as specified and as directed.

M&L Stone Walling of random rubble,uncoursed, well bonded, bedded and solidly hearted, built in CM (1:6) including provision of weep holes, complete all as specified and as directed.

M&L for Raised pointing to random or polygonal rubble, uncoursed or brought upto courses in CM (1:4) ,complete all as specified and as directed.

S & F Second class hard wood timber boarding ,25 mm thick, planed one side with butt jointsc, fixed with nails ,as in eve board, complete all as specified and directed.

S&F of 35mm thick 2nd class hard wood plain framed panelled shutter (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers supplied fitted to chowkats complete all as specified and as directed.

S&F 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed

S&F butt hinges of 100mm size, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 150mm size aluminium handles cast type, anodised complete all as specified and as directed

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 300mm complete all specified and as directed.

S&F Harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc.complete all as directed

S&F mild steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

M&L TMT steel bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete as in reinforcement to concrete all as specified and as directed.

M&L TMT steel bars, 6 to 8 mm dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete as in reinforcement to concrete all as specified and as directed.

All as per serial item No 35.00 here -in-before but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders.

S&F mild steel work (miscellaneous) as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlines to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290-Gde-E-165 complete all as specified and directed.

S & F Rolled mild steel structural steel work as in doors or gates of angle or other section with gusset plates, rails, braces etc. complete , drilled for fixing of steel sheeting or other covering, Door etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides ) and hanginbg; also fastening and fixing ,conforming to Fe-290 (Gde E-165), complete all as specified and directed.

S & F mild steel framed work such as grills gratings etc with ends of bars shouldered and or rivetted or forged into spikes framed guard bars and similar work conforming to Fe-290-0 Gde E-165 complete all as directed. (NOTE :- Serviceable mild steel obtained from item No here in before shall be re used)

S&F structural steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St 240 complete including painting with one shap coat of zinc chromate primer paint including preparation before febrication all as specified and as directed.

S & F Rolled mild steelplates( plain, or chequered) channel, square cut or notched, forming holes, with riveted , bolted or welded attachment conforming to Fe-410-W , complete all as specified and directed.

S & F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and as directed.

S & F steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete without glazing bars dovetailed or welded complete all as specified and as directed.

S&F 0.50mm thick prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour as approved of 550 Mpa tensile strength as in roof covering/ cladding to wall etc. fixed with self tapping screws complete as specified and directed

S&F 0.50 mm thick Prepainted galvalume aluminium zinc coating GI based plain steel sheet any colour as approved of 550 Mpa tensile strength as in ridges etc fixed with self drilling and self tapping screws, complete all as specified and directed.

S&F of MS screw bolts (Machine Made) 11 to 15 mm dia of shank with hexagonal and square heads at one end and screwed the other end and each screwed end to be fitted with washer and one square or hexagonal nuts n.exc 10 cm long complete all as specified and as directed.

M&L Damp proof course to horizontal or vertical surfaces on RCC roof / parapet etc. comprising with the following operations and as specified herein below :- (a) Preparing & cleaning of fully dried cement plastered surface (d) Applying one coat of cold bituminous primer to the plastered surface @ 0.30 to 0.50 kg per Sqm (e) One coat of blown type bitumen @ 1.50 Kg/Sqm binding with clean dry sand @ 0.05 Cum per Sqm . (f)Laying 150 Micron polythene film (g) Providing 40 mm thick PCC 1:2:4 , type B0 ( using 12.5 mm graded stone aggregate) including necessary form work

S&F for HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board, 4 mm thick of size 600x600mm,classic to be fixed aluminium grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size and finally applying two coats of oil bound distemper complete all as specified and directed.

M&L for 75 mm PCC 1:4:8 type D-2 (using 40mm graded atone aggregate aggregate) as in sub base of floor, complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded aggregate) as in paving/plinth protection , laid in alternate bays, finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 40mm thick PCC 1:2:4 type B1 (using 20mm graded aggregate) as in flooring finished the surface even and smooth without using extra cement complete all as specified and as directed.

S&F of 3mm thick and 38mm wide glass dividing strips inserted in position in floor to conform to design complete all as specified and as directed

M&L for 15mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6 finished surfaces even and smooth (without using extra cement) complete all as specified and as directed

M&L for 15mm thick rendering in two layers of 10mm thick and 5mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 finished fair and even, using water proofing compound in top layer , complete all as specified and as directed (NOTE: WPC will be measured and paid separately as "Supply only " here in after)

M&L for 5mm thick rendering on fair faces of concrete surfaces as in ceiling in cement mortar 1:4 finished surfaces even and smooth (without using extra cement) complete all as specified and as directed.

Supply only integral water proofing compound of approved quality complete all as specified.

M&L for preparation of newly plastered surface of wall and applying two coats of distemper oil emulsion over priming with chalk whiting , complete all as specified and as directed.

M&L for preparation on newly plastered surfaces on wall and applying two coats of cement based paint over priming coat of alkali resistant priming paint ,complete all as specified and as directed.

S&F 3mm thick sheet glass , ordinary quality and glazing with oil putty in square n.exc 0.50 sqm each panes complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint (1st quality) over priming coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint (1st quality) over a coat of primer, complete all as specified and as directed.

M & L for Cement concrete 1:3:6 Type C-2 ,(using 20mm graded stone aggregate), as in surface channels and drains, etc., including use and waste of necessary Form Work, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and as directed.

S&F 110 mm PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trances or in floors complete all as specified and as directed.

M&L point wiring with, two single core, 1.5 Sqmm (nominal area) size multistranded FRLSH copper conductor cable and one single core 1.5 Sqmm (nominal area) size solid copper conductor cable using colour code as phase , Neutral and as Earth continuity conductor connected to common earth dolly, 1100 volts grade ,PVC insulated, unsheathed cable drawn through and including PVC casing capping and PVC boards with all fittings and fixing materials for one Light /Fan point controlled by one no one way switch all as specified and directed.

All as per item No 66.00 here-in-before but but with cable size 2.5 Sqmm for one 5 pin 15 Amps socket outlet on independent board and multistranded insulated copper earth continuity conductor of size 1.5 Sqmm all as specified and directed by Engineer-in-Charge

S&F switch piano, flush type, 5Amp, single pole, one way white colour conforming to IS and/or as approved by GE,complete all as specified and as directed.

S&F Switch socket combination , 2 in 1, 5 Amps/16 Amps flush type, 230 volt, conforming to IS and/or as approved by GE, complete all as specified and directed.

S & F Ceiling fan, 1200 mm sweep , suitable for 230 volts, 50 Hz including provision of down and other accessories ( without regulator ) and connecting up Electrically with new Flexible Copper Cable, size as ordered, complete all as directed. MAKE :- ORIENT/ BAJAJ / USHA/ POLAR)

S&F L for ceiling rose, surface Bakelite PVC board 65 x 50mm two to three terminals, conforming to IS and/or as approved by GE, complete all as specified and as directed.

S&F lamp holder insulated body PVC/Polycarbonate type with back plate suitable for batten fittings including 1x 10 watt LED lamp complete all as specified and directed.

S & F MCB SPN 40 Amps rating ,240 volts grade , " C" curve , conforming to IS and/or as approved by GE,including taking down the old one, complete all as specified and directed .(Make : Legrand/Schneider/L&T)

S & F MCB SPN 6 to 32 Amps rating ,240 volts grade , " C" curve , conforming to IS and/or as approved by GE,including taking down the old one, complete all as specified and directed .(Make : Legrand/Schneider/L&T)

S & F MCB DB Single pole and neutral 4 way sheet steel phospetised powder painted with 200 amps rated bus bar 240V neutral link, earth bar and Din rail double door complete all as specified and directed (Make : Legrand/Schneider/L&T)

M&L for earthing with galvanized steel earth plate 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connected to galvanized iron earth wire 4 mm as earthing lead by means of bolts nuts check-nuts and washers of galvanized iron or steel besides welding at all joints as shown in drawings and including excavation and earth work GI pipe light grade 15mm bore for protection of GI wire from earth electrode to earth dolly including earth test point of galvanized iron or steel of size 75x75x25 mm supplying and laying char coal dust, common salt PCC 1:2:4 type B-1 chamber and MS angle frame 40 x 40 x 3 mm and RCC cover 40 mm thick (1;2:4) type B-1 using 20 mm graded stone aggregate reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia GI funnel and wire mesh 20 mm dia GI pipe light grade for watering all as shown in drawing and connected to earth test point including testing complete all as specified and directed.

S & F Wall mounted LED batten 20 watt extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver with all accessories, pre-wired connecting up with new flexible copper cable of size 0.75 Sqmm, 3 core , complete all as specified and directed. ( Make- Havells Ordering Code No LHFXCEP1TN1W020 (Batten) , LHEXCEP7UN1W020 (LED bTube)or equivalent in Philips/Bajaj)

Supply and laying well burnt brick, Sub class ‘B’, old size as in cable protection, laid across in trenches complete all as specified and directed.

M&L sand cushioning with approved fine grade sand for protection of under ground cable complete all as specified and as directed NOTE : Finished measurement after punning down shall be considered for payment.

Supply, laying, connecting and testing XLPE insulated (Earthed) cable in trenches/or fixed on pole etc in screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with stranded aluminium conductor, 1100 Volt grade, cross sectional area 10 Sqmm, 2 Core Conforming to IS-7098 (Part-II)-1985 including taking up/down unsv under ground cable, complete all as specified and directed.(Note: Excavation & earth work shall be measured and paid separately)

S&F galvanised iron tubing, 40 mm bore , light grade with all fittings for passing of under ground cable as in cable protection, complete all as specified and as directed.

S&F galvanised iron tubing, 25 mm bore , light grade with all fittings , fixed to wall ,ceiling or or laid in floor for passing of under ground cable as in cable protection, complete all as specified and as directed.

ABHISEK TRADING AND CO

awomi enterprises