Construction of Hostel building at Khanvel, Mandoni, Amboli and Randha (3rd call)

Amount

Khanvel

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and stacking of useful materials and disposing of the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Providing material and labour for filling in plinth etc WITH UNSCREEN GRAVEL under floors including watering, ramming consolidating and dressing etc. complete.

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each disposited layer by ramming and watering.

Providing material and labour for injecting Chemical emulsion for PRE - CONSTRUCTIONAL anti-termite treatment and creating a chemical barrier on the top surface of plinth filling, inside junction of wall and floor, on top of damp proof course (DPC) or on masonry at level of plinth filling as per IS 6313 (Part-2)-1981 using chemical like chloropyripos emulsifiable, Biflex TC, lindane (IS 8944-1978) 20EC mixed with water in 1:19 ratio (1 liter chemical : 19 liters of water). The emulsion shall mentioned below, all as per specification and directions of Engineer-in-charge. Plinth area in plan at GF shall only be measured (for akk below specified steps) and paid. A guarantee bond of 10 years shall be furnished. A1) Bottom surface and the sides of the excavation made for masonry foundations at the rate of 4 liters/sqm (wherever applicable) A2) At the rate of 7.5 liter/ sqm to the backfill at the depth of 500mm below the original ground level. The soil in the immediate contact with the vertical surface of RCC column/ Masonry shall be treated. B) Top surface of the plinth filling including damp proof courses at the rate of 5 liter/sqm of internal plinth area etc. complete. C) At the rate of 7.5 liter/ sqm to the internal vertical surface from original Ground level to top of the earth filled in the plinth. D) At the rate of 7.5 liter/ sqm to the external vertical surface below finished Ground level to the full depth of the filling complete. E) 1 liter / linear meter along the junction of wall and floor at all stages.

Providing material and labour for laying Autoclave Aerated Concrete Block chips/ bats cement mortar in 1:6 (1 Cement : 6 Coarse Sand) with Autoclave Aerated Concrete Block chips/ bats for sunk filling grade including compacting, finishing, curing etc. complete as directed by engineer in charge.

Filling in foundation and plinth with brick bats Chhara in layers of 20 cm thickness including watering, ramming and consolidating etc. complete.

Providing and laying PLINTH PROTECTION including excavation of 30cm. Depth and filling with Brick bats of 20cm. Thick and C.C. 1:2:4 ( 1 cement :2 coarse and :4 graded stone aggregate 40mm nominal size) of 10cm. Thick and top layers of C.C. 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregates 20mm. Nominal size ) of 50mm, thick including finishing top surface with floating coat of neat cement slurry.

Providing material and labour for laying Plain cement concrete M15 in Foundation and Plinth including cost of formwork, compacting, finishing, curing etc complete for all level, all height/ depth as directed by engineer in charge.

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in (A) Foundations, footings, Base of columns and Mass concrete. (upto 10 ton)

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. Height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ reinforced concrete and plain concrete work in. (A) Foundations Footings Bases of Columns etc. and Mass concrete. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts, upto floor two level. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts, Above floor two level & upto Level Three. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding the Cost of reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts above floor three level upto floor four level etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever upto floor two level etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever above floor two level upto floor three level etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever above floor three level upto floor four level etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.200 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in (C) Slabs,landing,shelves,Balconies Lintels, Beams, Girders and Cantilever upto floor two level. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in (C) Slabs, landing, shelves and Cantilever upto floor two level, etc complete as directed by engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in (C) Slabs, landing, shelves and Cantilever above floor two level upto floor three level etc complete as directed by engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in (C) Slabs, landing, shelves and Cantilever above floor three level upto floor four level etc complete as directed by engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (B) Walls, from top of foundation level upto floor two level (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding the cost of reinforcement for reinforced concrete work in (E) Staircases upto floor two level, etc complete as directed by engineer-incharge.

Providing material and labour for laying Controlled cement concert M-250 and curing complete including cost of Form work with steel sheet sheating etc. excluding the cost of reinforcement of reinforced concrete work the in STAIRCASE ABOVE FLOOR TWO LEVEL UPTO FLOOR THREE LEVEL.

Providing material and labour for laying Controlled cement concert M-250 and curing complete including cost of Form work steel sheet sheating excluding the cost of reinforcement of reinforced concrete work the in STAIR CASE ABOVE FLOOR THREE LEVEL UPTO FLOOR FOUR LEVEL.

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level (upto 10 ton)

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including bending, binding and placing in position complete Above floor two level & upto Level Three

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level (upto 10 ton)

Providing, Suppying and mixing Dr. Fixit water proofing materials in cemrnt concrete in proportion I.e. 200ml for 50 Kg of 1 cement bag, Or recommended by the manufacturer. It is to be mix in wet concrete.

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in Above plinth level upto floor level two in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in Above floor two leve in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in Above floor Three level in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Half brick thick honey- comb brick work with common burnt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. (i) In Cement Mortar 1:4 ( 1- Cement : 4 - coarse sand) (upto 10 ton)

Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:3 ( 1-Cement : 3-coarse sand ) with 2 Nos of 6mm Mild steel round bars after every three course embedded in Cement Mortar inAbove plinth level upto floor level two (B) Conventional (upto 10 ton)

Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:3 ( 1-Cement : 3-coarse sand ) with 2 Nos of 6mm Mild steel round bars after every three course embedded in Cement Mortar in Above floor two level (B) Conventional (upto 10 ton)

Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:3 ( 1-Cement : 3-coarse sand ) with 2 Nos of 6mm Mild steel round bars after every three course embedded in Cement Mortar in Above floor three level (B) Conventional (upto 10 ton)

Providing material and labour for 6mm thick CEMENT PLASTER in single Coat For plastering on ceiling and soffits of stairs UPTO FLOOR TWO LEVEL & ABOVE finished even and smooth including curing etc. complete in C:M 1:3 (1 cement :3 fine sand) and finishing with floating coat of neat cement slurry.

Providing material and labour for 12mm thick CEMENT PLASTER in Single Coat For plastering on Brick concrete wall surfaces for plastering UPTO FLOOR TWO LEVEL & ABOVE finished even and smooth including curing etc. complete in C:M 1:3 (1 cement :3 fine sand) and finishing with floating coat of neat cement slurry.

Providing 20mm thick cement plaster in double coat on single or half brick walls for interior plastering upto floor two level & above two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) finishing with floating coat of neat cement slurry.

Providing material and labour for fixing polished kota stone slab flooring 20 mm (average) thick base of cemetn mortar 1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing etc. complete (A) 25 mm thick.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on existing flooring by adhesive material including dismentaling of existing flooring and jointed with color cement slurry including finised with flush pointing & cleaning the surface etc, Including cost of material & Labour for fixing spacer, epoxy grouting for filling in joints between tiles. complete for antiskit (upto 10 ton)

Providing and laying coloured glazed tiles of the size 300 mm x 200 mm x 8 mm / 300 mm x 450 mm x 8 mm in skirting, risers of steps and dedo on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with white cement slurry.

Providing and fixing 18 mm thick Granite of any colour and shade gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing and laying chequered precast cement concrete tiles 22mm thick with aggegate of sizes upto 6mm in floors, treads of steps and landings on 20mm thick bed of C.M. 1:6 (1-cement : 6-sand) or L.M. 1:1.5(1-Lime putty : 1.5 coarse sand) joint with neat cement slurry with pigments to match the shade of the tiles. (upto 10 ton)

Providing and fixing tiles roofing with manglore tiles including cement mortar of 1:4 ratio over Sloping RCC slab roof.

Providing and fixing 150mm wide 450mm over all semicircular plain G.I.sheet class-3 gutter with Iron brackets 40mm x 3mm size Bolts, Nuts, washers etc. including making necessary connection with rain water pipes. (i) 0.80 mm thick Sheet. (upto 10 ton)

Providing and fixing 1000mm high stainless steel railing consisting of 50mm dia round SS pipe hand rail supported on 75mm high 25mm x 25mm X 2mm square SS pipe fixed to about 875mm high 38mm x 38mm square SS pipe balustrades placed about 900mm centre to centre. Each balustrade is to be secured by 4 Nos. M8 x 100 fasteners of hilti or any other approved equivalent make and covered with 75mm x 8mm thick base plate with cap. Stainless steel to be Minimum 16 gauge of SS 304 grade complete in all respects as approved by Architect/ Engineer-in-charge.

Distempeing (Two coats) with oil bound distemper of approved brand and manufacture and of required shade on wall surfaces to give an even shade, over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth.

Finishing wall with water proofing cement paint of on wall surfaces (Two coats) to give an approved brand and manufacture and of required shape even shade after thoroughly brushing the surface to remove all dirt and remains of loose powered materials.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing material and labour for fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws, with Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS :2046 Type S, including cost of adhesive of approved quality 1.0mm Thick on both face, with Providing and fixing S.S. tower bolts (barrel type) with necessary screws etc 200mm long x10mm dia, with Providing and fixing S.S. Door Aldrop with necessary screws etc. 300mm long x16mm dia, Providing and fixing S.S. Door Aldrop with necessary screws etc 250mm long x16mm dia, with Providing and fixing S.S. Pipe Handle for door 30cm size on both side of Door shutter, with Providing and fixing S.S hanging type floor door stopper with necessary screws, etc. complete as directed by Engineer in charge. All S.S Shall be ASIS 304 Grade.

Providing and fixing 35 mm thick shutters for Doors, windows and clerestory windows including Indian teak wood frames 12 cm x 7 cm. size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. (iii) Partly panelled and partly glazed.

Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S. flats at required spacings and frame alround, square or round bars with round headed bolts and nuts or by screws. (B) PLAIN GRILL (upto 10 ton)

Providing and fixing Fly proof galvanised M.S. wire gauge of I.S.l gauge designation 85 G. with wire of dia.0.56 mm to windows and celevating windows including 60 x 20mm beading of teak wood. (upto 10 ton)

Providing upto floor two level precast cement concrete jali or grill 1:2:4 mix (1- Cement : 2- coarse sand : 4-graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia. Mild steel wire including roughening,cleaning, fixing and finishing in cement mortar 1:3 and curing complete. (D) 75mm thick

Providing material and labour for construction of Kitchen Platform made from Black Granite (16mm to 18mm thick) in top of kitchen platform rested on black kadapa stone (av.30mm thick) supported on sandwiched vertical supports of Kadapa Stone bottom of granite stone for base of platform, at required distance or as directed by Engineer-in-charge. One side vertical granite stone in geometrical shape, front granite stone patti for fascia work as well as horizontal boarders including molding and mirror polishing by hand grinder to all exposed black granite edges and providing opening of required size and shape of kitchen sink in granite and kadapa stone in line and level. The vertical supports of kadapa stone sandwiched/ gap fill up with cement mortar 1:1 and cement slurry and the granite stone vertical side and patti etc with adhesive material like Araldite etc complete as directed by Engineer-in-charge.

Providing material and labour for making BLACK GRANITE STONE COUNTER WASH BASIN of 0.60mt wide with vertical & Horizontal support of granite stone and having bottom Slab of 25mm to 30mm thick kadappa stone fixing with cement mortar 1:4 ( 1 cement :4 fine sand) and neat cement slurry as per requirement including cutting the granite stone & Providing & fixing oval shape wash basin (Make Jaquar CODE : CNS-WHT-WB02 : Under Counter Basin Size(mm) 195 x 600 x 425) white colour in line & level. All exposed Edges of granite should be moulded including all accessories , flexible inlet pipe 15mm dia, C.P brass waste coupling 32mm, PVC waste pipe 32mm etc. as directed by engineer in charge.

Providing Material, Labour and equipments for Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thickjointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : including Khurra & Gola work With average thickness of 120 mm and minimum thickness at khurra as 65 mm, etc complete as directed by engineer-incharge.

Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(G)110 mm -spigot and socket soil, waste and ventilating pipes

Providing and fixing in position cowel went to pipes.(C) 100mm dia

Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size 580mm (Earthwork, bed concrete, foot reste and trap to be measured and paid for separately) (A) Vitreous China.(I) Long pattern = White colour

Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be measured and paid for separately)(A) vitreous China Pattern :(i) in white colour

Providing and fixing 100mm size P or S trap for water closet squatting pan including jointing the trap with the pan and soil pipe in cement Mortar 1:1 (1-Cement : 1-Fine sand)(A) Vitreous China.

Providing and fixing 12.5 Litres high level C..I. flushing cistern with A pair of C.I. or Mild steel brackets, womplete with fittings such as syplionic arrangement, 15mm nominal size brass ball valve with polythene float, lever G.I. China (60 cm. ) and pull union and couplings for connections with inlet, outlet and overflow pipes etc. including cutting holes in walls and making good the same (overflow pipe to be measured and paid fo separately )

Providing and fixing in position with clamps etc. 32mm nominal internal diameter galvanised steel tube flush pipe for high level flushing cistern including connecting the flush pipe with cistern and closet and making good the walls and floors.

Providing and fixing G.I. inlet connection for flush pipe with W.C. Pan

Providing and fixing plastic seat and cover for wash down water closer with C.P. brass hinges and rubber buffers. (B) Black plastic seal and cover.

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour.

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white including cutting holes in walls and making good the same but excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm size

Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mmdia.

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A) 100mm dia. Each

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.

Providing and fixing 600mm x 120mm glass shelf with C.P. brass bracket and guard rail complete mixed to wooden plug with C.P. brass screws.

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (i) 15mm dia.

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (ii) 20mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia.

Providing and fixing brass screw down stop tap.(B) 20mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(B) 20mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(i) 20mm dia.

Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware 550mm x 300mm.

Providing and fixing Rubber plug for sink or wash basin.

Providing and fixing chromium plated, bottle trap with necessary couplings of approved quality for wash basin.

Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (i) 25mm dia.

Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not less than 35Kg.

Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm. length.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [B] 20 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [C] 25 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [D] 32mm.

Providing erecting and fixing double coated Syntex PVC. (ISI) water tank of required capacity each with all necessary fittings and connection etc. complete on terrace.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls.

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including testing of pipes and joints complete.(B) 150mm dia. (upto 10 ton)

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(A) 100 mm dia. (112 mm Ave.bed thickness)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P type. (upto 10 ton)

Construction of B.B. Masonary Kundi of clear inside dimension size 0.60M x 0.45M x 0.45M with 23cm thick B.B. masonary wall in C:M 1:6 including required excavation, C.C. 1:5:10 15cms. Thick refilling 12mm thick cement plaster to masonary and floor C.C. layer and fixing the cast R.C.C. manhole cover of size 0.60M x 0.45M With frame and white/ colour wash etc. complete.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or two inlets. (upto 10 ton)

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(i) for 455mm x 610mm size.

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(ii) for 500mm x 700mm size.

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. (upto 10 ton)

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(D) 300mm (upto 10 ton)

Drilling of 215mm dia macked bore in loose and alluvial strata and 165mm dia bore in hard and Rocky formation by DTH Rig etc. including cleaning the bore testing of water etc. complete.

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost of rings as per IS specification No.4985/1988 incluidng all local and centra taxes, transportation, freight charges, octroi, ispection charges octroi, inspection charges loading, unloading conveyance to the departmental stores and including cost of jointing materials etc. complete for following dia and ring fit type pipe including lowering, laying and jointing PVC pipes and specials of following class and diameters including cost of labours materials exept cement solvent giving satisfactory hydraulic testing as per ISI cose etc. complete 180mm dia test pressure 6kg/CM2.

Supplying of single phase submersible pump set suitable for 100 mm size or more dia borewell having motor capacity and discharge as under with necessary pannel box (c) Motor rating 2 HP (17 stage) pump having capacity of 106 LPM at 40 mtr head suitable for 25 mm dia. delivery pipe including Supplying and erecting Direct - On - Line Starter with 18 A. rating contatctor and with 3.5 Amp. 18A range directely operated in totally insulated elegant enclosure for single phase operation upto 3 HP as per IS 13947 complete erected on P.W. Block with necessary connection.

Providing and erecting ISI marked PVC insulated PVC Shethed Flat flexible Submercible copper cable approved make of following Size. (b) 3 Core x 2.5 Sq. mm.

Providing material & labour for supplying in standarad length ISI mark high density Polyethylene HDPE pipes suiatable for potable water as per IS Specification no. 4984/1995 including all local and central taxes, transportaion, freight charges, orctroi, inspection charges, loading, unloading, conveyance to the dept. strores etc. comp. rate for HDPE (PE-100) pipe based on the rate of HDPE resin as Rs. 110292.58 (incul. of excise duty @ 12.36% but exclu. of freight and sales tax) Dtd. 1-03-2013. (b) 10.0 kg/cm2, (I) with Excise Duty 50mm dia PVC Pipe.

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.(a) with medium class Rigid PVC pipe and accessories 1.For Point wiring above 10 mtr of length, additional length will be added at rate of mains.

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.(a) with medium class Rigid PVC pipe and accessories

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories.[I] For 6A Plug with 2-1.5 sq.mm Cu. Wire(a) with medium class Rigid PVC pipe and accessories

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories.[III] For 16A Plug with 2-4 sq.mm Cu. Wire(a) with medium class Rigid PVC pipe and accessories

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed.Note:- Maximum up to 6 mtrs length, excess will be considered as Mains for Secondary Point.(a) with medium class Rigid PVC pipe and accessories

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. One No 5 pin plug

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. Blank Plate Single

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular MCB Switch

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 20 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 25 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 32 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 20 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 25 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 32 mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 2 wire 1.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 2 wire 2.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 4 wire 6 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 4 wire 10 sq. mm

Supplying & erecting M.S. Box having 16 Gauge painted with red oxide or Heavy duty PVC box erected flushed on wall or concealed in wall with necessary plastering & finishing as directed of following size.(d) 250 mm x 300 mm x 75 mm(d)

Providing & Erecting 3mm thick Polycarbonate (PC) sheet with grooving as directed

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. b).RG-6

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge TV Co-axial Socket outlet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 %, CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates )(a) Tube Light With integral/ non-integral driver, 16-18- Watts, Surge - 4KV, IP-20, 4 Feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % , CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) Tube Light With integral/ non-integral driver, 36- Watts, Surge - 4KV, IP-20, 4 Feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) LED Lamps Integral type, cool white with PC diffuser Suitable for B22 Lamp Holder, 5-8 Watts.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) LED Panel Light with provision for Plane front Frame with translucent cover fixed to housing complete. 12-15 watt, 200 x 200 mm, Surge-4 KV.

Providing and erecting Approved make Ceiling fan with double ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24/0.2 , 3 core flexible wire with earthing. [Make shall be approved by Engineer in charge]

Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with condenser A.C.230V 50c/s. 1400 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24 / 0.2, 3 core flexible Copper wire with earthing [ Make shall be approved by Engineer in Charge]

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in RCC slab with Making the site as original.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with necessary finishing.

Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. Bolt & Nuts erected with necessary hook of 10 mm M.S. Round Bar.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box.

Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square frame ABS body with inbuilt lowers & square frame.

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM, 305 mm dia 900 RPM

Providing suitable M.S. louver shutter of the Exhaust fan.

Providing recess in wall or window frame suitable for erection of Exhaust fan complete with plastering and colour washing to match the colour of the wall or window complete with expanded metal in order to render the fitting in accessible and the room water-proof.

Providing window frame suitable for erection of Exhaust fan complete covering the remaining portion of window with 15 mm. thick plywood and colour washing to match the colour of the wall.

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Single phase 4 way SS Double door

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Single phase 8 way SS Double door

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Three phase 6 way SS Double door for single phase outgoing horizontal box

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Single Phase 4 Way

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Single Phase 8 Way

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Three Phase 6 Way

The Above all items of MCB, DB the cost of erection on New angle iron frame add following.up to 8 way single phase

The Above all items of MCB, DB the cost of erection on New angle iron frame add following.above single phase 8 way and all three phase DBs.

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 25 Amps.DP

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 40 Amps.DP

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on 3 phase and neutral 415V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component for following Max. rating erected as directed. 40Amps. FP

Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 6 to 32 Amp.

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 40 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 6 to 32 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 40 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 63 Amp.

Approved make Three Phase & Neutral LT Heavy Duty Switch Disconnector Fuse Unit Cubical type for panel mounting complete with operating mechanism suitable to operate on 415V A.C. , 23A duty With HRC fuses of suitable load confirming to IS. 13947 (Part I & III). of following capacities.100Amp/125 Amp

Cable Terminal ( ‘Plain" Type)Set of Four for 32 / 63 Amps

Cable Terminal ( ‘Plain" Type)Set of Four for 125/200 Amps

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting Aluminium Busbars with four equal Nos. of bus having current density not more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket to each busbar,erected in existing cubical panel with necessary connections. Suitable for 200 Amp. Capacity

Supplying and erecting approved make 415V bakelite fuse fittings for front connection / busbar type, to accommodate HRC fuse link, with spin - riveted brass contact, having thermo plastic inflammable material & single piece extruded brass box contact to lock with adequate cable hole to accommodate aluminium conductors suitable for (without HRC fuse) 16 Amp.

Supplying Bolted Connections (BS type) HRC fuse link capable to withstand 80KA confirms to I.S. 13703 for following current capacity up to 32 Amp.

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board having IP-64 protection made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary supporting angles, flats including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge with erection of supplied switch gears, BUSBARS, with suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses for measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket complete. The Panel shall be painted with epoxy powder coating. (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following approved manufacturers with following size.(A) The standard companies switch gear shall be used and only manufacturers at CPRI approved factory and shall be certified by that company whose switch gears are used after fabrication for beneficial use with 350mm depth

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using proper clamp.

Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For panel)

For using salt and charcoal / coke as required for pipe type earthing.

Add Extra for excavation in Hard rock by dry and wet blasting and chiselling for pipe type earthing.

Supplying and erecting LED Street Light/Flood light fittings with High power White LED's wattage of 1 watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminium housing with smooth finish powder coated and heatsink extruded aluminium with diffuser and Polycarbonate optics/lenses with company mark/name engraved or embossed 120 to 300 V, Power Factor more than 0.95, THD less Than 10% CCT 5000 K to 5700 K, Uniformality ratio >0.45, Luminaire efficiancy > 85 lumen/watt, LED driver efficiancy > 85 %. CREE/OSRAM/PHILIPS Lumileds/NICHIA/SEOUL/Bridge Lux ( U.S.A.) make LED used for luminaire. ( Each fittings required LM-79 & LM-80 Certificates) Flood Light (IP-65), Surge- 4 KV Above 70 watts to 90 watts

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

Making trench in Hard Murrum / Tar Road of suitable width of 90 cms or required depth for laying any size of cable or locating the fault all over the run and back filling the same and making the surface as normal ground.

(B) If additional machineries like hammer driller or JCB use [Add]

Covering of cable with second class bricks or cement tiles laid cover the cable crosswise & also on both sides with covering of 7. 5 Cms. layer of sand above & below cable (16 bricks per meter)

Providing and erecting iron clad cable route marker duly marked with ELE.CABLE of size 23 cms.X 12 cms. Flushed with ground in cement foundation as directed by Engineer in charge.

Supplying following size of Light duty “A” Class G.I . Pipe & erecting as directed by Engineer-in-charge. 50 mm dia

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. 2 to 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. 3 & 1/2 core 70 Sq. mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 1.5/ 2.5/4/6 Sq.mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 70 Sq.mm.

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 35/50 Sq.mm.

Providing and erecting 18 G. M.S. termination box outdoor type suitable for- 1.1 KV PVC insulated armoured cable complete erected with clamp, bolts, nuts etc. suitable of following size of cables.3 core 70 / 95 Sq. mm

Providing and erecting Epoxy Outdoor / Indoor end termination Kit suitable for LT PVC insulated armoured cable1.1 KV grade complete with ferrule bushing and accessories and suitable clamps duly erected and connected to the supply for all cores cables of following size. 2.5 to 16 Sq. mm

Providing and erecting Epoxy Outdoor / Indoor end termination Kit suitable for LT PVC insulated armoured cable1.1 KV grade complete with ferrule bushing and accessories and suitable clamps duly erected and connected to the supply for all cores cables of following size. 70 to 120 Sq. mm

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame, prefilter housing with 'O' ring presediment filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40 Osg inline type post carbon filter auto low & high pressure switches with following size of storage tank & LPH capacity & erected as directed with one year comprehensive maintenance guarantee. [B] 25 Ltr / Hr with 30 Ltr. S.S. Pressure Tank

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 45°C. The outlet temp. of the water should drop by 15°C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating, coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.

Conveyance charges including loading / unloading for Water Cooler from store to site (ii) Outside Divisional Head Quarter for first 60 Km from store.

Supplying & erecting Galvanized iron pipe post “B” class 88.9 mm O.D 6 mtr. Long duly painted with two coats of aluminium paint complete with metallic base- plate of 300 mm x 300 mm x 4mm thick for using as a compound light pole with approx. weight 47 Kg.

Providing M-20 / 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of size 45 x 45 x 100 cms. Deep in below ground level with plinth of 45 cms x 45 cms (or 45 cms dia x 45 cms) high upper ground level with necessary curing and finishing in approved manner. ( for 4 & 6 mtr pole)

Fabricating terminal box for street light pole made from 16 SWG M.S. sheet having following size complete with fixing arrangement for terminal board, with necessary hole for wire entry and exit from the box. The box shall be provided with cover and hinges on one side and bolting at other end The box shall be fixed by clamps fabricated from 25mm x 6mm flat.The box shall be painted with one coat of red oxide and two coats of paint having following box size. 330 mm x 260 mm x 140 mm (depth)

Providing street light pole bracket comprising main Light Class MS tube of 4.2 cms. outside dia. complete with suitable M.S. sleeve tubing of approx. 45cms.length and suitable for 76.5mm. /80 mm or require size pole top having sufficient fastners for fixing the brackets and having suitable rise as per site condition as directed and spread of 2 mtr.with suitable welded stiffener reducer and with lock nut complete painted with one coat of Red oxide / PU base primer and two coats of Aluminium / PU paint. Suitable for side entry fitting brackets of following nos of arms.Single Arm bracket 2 Mtr

Supplying and erecting LED Street Light/Flood light fittings with High power White LED's wattage of 1 watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminium housing with smooth finish powder coated and heatsink extruded aluminium with diffuser and Polycarbonate optics/lenses with company mark/name engraved or embossed 120 to 300 V, Power Factor more than 0.95, THD less Than 10% CCT 5000 K to 5700 K, Uniformality ratio >0.45, Luminaire efficiancy > 85 lumen/watt, LED driver efficiancy > 85 %. CREE/OSRAM/PHILIPS Lumileds/NICHIA/SEOUL/Bridge Lux ( U.S.A.) make LED used for luminaire. ( Each fittings required LM-79 & LM-80 Certificates) Street Light (IP-65), Surge- 4 KV Above 48 watts to 60 watts Cat III

Amboli

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and stacking of useful materials and disposing of the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Providing material and labour for filling in plinth etc WITH UNSCREEN GRAVEL under floors including watering, ramming consolidating and dressing etc. complete.

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each disposited layer by ramming and watering.

Providing material and labour for injecting Chemical emulsion for PRE - CONSTRUCTIONAL anti-termite treatment and creating a chemical barrier on the top surface of plinth filling, inside junction of wall and floor, on top of damp proof course (DPC) or on masonry at level of plinth filling as per IS 6313 (Part-2)-1981 using chemical like chloropyripos emulsifiable, Biflex TC, lindane (IS 8944-1978) 20EC mixed with water in 1:19 ratio (1 liter chemical : 19 liters of water). The emulsion shall mentioned below, all as per specification and directions of Engineer-in-charge. Plinth area in plan at GF shall only be measured (for akk below specified steps) and paid. A guarantee bond of 10 years shall be furnished. A1) Bottom surface and the sides of the excavation made for masonry foundations at the rate of 4 liters/sqm (wherever applicable) A2) At the rate of 7.5 liter/ sqm to the backfill at the depth of 500mm below the original ground level. The soil in the immediate contact with the vertical surface of RCC column/ Masonry shall be treated. B) Top surface of the plinth filling including damp proof courses at the rate of 5 liter/sqm of internal plinth area etc. complete. C) At the rate of 7.5 liter/ sqm to the internal vertical surface from original Ground level to top of the earth filled in the plinth. D) At the rate of 7.5 liter/ sqm to the external vertical surface below finished Ground level to the full depth of the filling complete. E) 1 liter / linear meter along the junction of wall and floor at all stages.

Providing material and labour for laying Autoclave Aerated Concrete Block chips/ bats cement mortar in 1:6 (1 Cement : 6 Coarse Sand) with Autoclave Aerated Concrete Block chips/ bats for sunk filling grade including compacting, finishing, curing etc. complete as directed by engineer in charge.

Filling in foundation and plinth with brick bats Chhara in layers of 20 cm thickness including watering, ramming and consolidating etc. complete.

Providing and laying PLINTH PROTECTION including excavation of 30cm. Depth and filling with Brick bats of 20cm. Thick and C.C. 1:2:4 ( 1 cement :2 coarse and :4 graded stone aggregate 40mm nominal size) of 10cm. Thick and top layers of C.C. 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregates 20mm. Nominal size ) of 50mm, thick including finishing top surface with floating coat of neat cement slurry.

Providing material and labour for laying Plain cement concrete M15 in Foundation and Plinth including cost of formwork, compacting, finishing, curing etc complete for all level, all height/ depth as directed by engineer in charge.

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in (A) Foundations, footings, Base of columns and Mass concrete. (upto 10 ton)

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. Height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ reinforced concrete and plain concrete work in. (A) Foundations Footings Bases of Columns etc. and Mass concrete. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts, upto floor two level. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts, Above floor two level & upto Level Three. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever upto floor two level etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever above floor two level upto floor three level etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.200 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (C) Slabs,landing,shelves,Balconies Lintels, Beams, Girders and Cantilever upto floor two level. (more than 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in (C) Slabs, landing, shelves and Cantilever upto floor two level, etc complete as directed by engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in (C) Slabs, landing, shelves and Cantilever above floor two level upto floor three level etc complete as directed by engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (B) Walls, from top of foundation level upto floor two level (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (B) Walls, from top of foundation level upto floor two level (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding the cost of reinforcement for reinforced concrete work in (E) Staircases upto floor two level, etc complete as directed by engineer-incharge.

Providing material and labour for laying Controlled cement concert M-250 and curing complete including cost of Form work of with steel sheet sheating etc. excluding the cost of reinforcement of reinforced concrete work the in STAIRCASE ABOVE FLOOR TWO LEVEL UPTO FLOOR THREE LEVEL.

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level (upto 10 ton)

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including bending, binding and placing in position complete Above floor two level & upto Level Three

Providing, Suppying and mixing Dr. Fixit water proofing materials in cemrnt concrete in proportion I.e. 200ml for 50 Kg of 1 cement bag, Or recommended by the manufacturer. It is to be mix in wet concrete.

(ii) Uncoursed Rubble Masonry with hard stone of approved quality in foundations and plinth in Cement Mortar 1:5 (1-cement : 5-coarse sand including levelling up etc. complete (more than 10 ton)

(ii) Uncoursed Rubble Masonry with hard stone of approved quality in Above plinth level upto floor level two in Cement Mortar 1:5 (1-cement : 5-coarse sand including levelling up etc. complete (more than 10 ton)

(ii) Uncoursed Rubble Masonry with hard stone of approved quality in Above floor two level in Cement Mortar 1:5 (1-cement : 5-coarse sand including levelling up etc. complete (more than 10 ton)

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in Above plinth level upto floor level two in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in Above floor two leve in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Half brick thick honey- comb brick work with common burnt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. (i) In Cement Mortar 1:4 ( 1- Cement : 4 - coarse sand) (upto 10 ton)

Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:3 ( 1-Cement : 3-coarse sand ) with 2 Nos of 6mm Mild steel round bars after every three course embedded in Cement Mortar inAbove plinth level upto floor level two (B) Conventional (upto 10 ton)

Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:3 ( 1-Cement : 3-coarse sand ) with 2 Nos of 6mm Mild steel round bars after every three course embedded in Cement Mortar in Above floor two level (B) Conventional (upto 10 ton)

Providing material and labour for 6mm thick CEMENT PLASTER in single Coat For plastering on ceiling and soffits of stairs UPTO FLOOR TWO LEVEL & ABOVE finished even and smooth including curing etc. complete in C:M 1:3 (1 cement :3 fine sand) and finishing with floating coat of neat cement slurry.

Providing material and labour for 12mm thick CEMENT PLASTER in Single Coat For plastering on Brick concrete wall surfaces for plastering UPTO FLOOR TWO LEVEL & ABOVE finished even and smooth including curing etc. complete in C:M 1:3 (1 cement :3 fine sand) and finishing with floating coat of neat cement slurry.

Providing 20mm thick cement plaster in double coat on single or half brick walls for interior plastering upto floor two level & above two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) finishing with floating coat of neat cement slurry.

Pointing on Uncoursed stone masonry with cement mortar 1:3 (1-cement : 3-coarse sand)(B) Ruled pointing

Providing material and labour for fixing polished kota stone slab flooring 20 mm (average) thick base of cemetn mortar 1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing etc. complete (A) 25 mm thick.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on existing flooring by adhesive material including dismentaling of existing flooring and jointed with color cement slurry including finised with flush pointing & cleaning the surface etc, Including cost of material & labour for fixing spacer, epoxy grouting for filling in joints between tiles. complete for antiskit (upto 10 ton)

Providing and laying coloured glazed tiles of the size 300 mm x 200 mm x 8 mm / 300 mm x 450 mm x 8 mm in skirting, risers of steps and dedo on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with white cement slurry.

Providing and fixing 18 mm thick Granite of any colour and shade gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing and laying chequered precast cement concrete tiles 22mm thick with aggegate of sizes upto 6mm in floors, treads of steps and landings on 20mm thick bed of C.M. 1:6 (1-cement : 6-sand) or L.M. 1:1.5(1-Lime putty : 1.5 coarse sand) joint with neat cement slurry with pigments to match the shade of the tiles. (upto 10 ton)

Providing and fixing tiles roofing with manglore tiles including cement mortar of 1:4 ratio over Sloping RCC slab roof.

Providing and fixing 150mm wide 450mm over all semicircular plain G.I.sheet class-3 gutter with Iron brackets 40mm x 3mm size Bolts, Nuts, washers etc. including making necessary connection with rain water pipes. (i) 0.80 mm thick Sheet. (upto 10 ton)

Providing and fixing 1000mm high stainless steel railing consisting of 50mm dia round SS pipe hand rail supported on 75mm high 25mm x 25mm X 2mm square SS pipe fixed to about 875mm high 38mm x 38mm square SS pipe balustrades placed about 900mm centre to centre. Each balustrade is to be secured by 4 Nos. M8 x 100 fasteners of hilti or any other approved equivalent make and covered with 75mm x 8mm thick base plate with cap. Stainless steel to be Minimum 16 gauge of SS 304 grade complete in all respects as approved by Architect/ Engineer-in-charge.

Distempeing (Two coats) with oil bound distemper of approved brand and manufacture and of required shade on wall surfaces to give an even shade, over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth.

Finishing wall with water proofing cement paint of on wall surfaces (Two coats) to give an approved brand and manufacture and of required shape even shade after thoroughly brushing the surface to remove all dirt and remains of loose powered materials.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete

Finishing Stone masonary wall with Asian make PU paint coating on stone surface to give an required shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing material and labour for fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws, with Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS :2046 Type S, including cost of adhesive of approved quality 1.0mm Thick on both face, with Providing and fixing S.S. tower bolts (barrel type) with necessary screws etc 200mm long x10mm dia, with Providing and fixing S.S. Door Aldrop with necessary screws etc. 300mm long x16mm dia, Providing and fixing S.S. Door Aldrop with necessary screws etc 250mm long x16mm dia, with Providing and fixing S.S. Pipe Handle for door 30cm size on both side of Door shutter, with Providing and fixing S.S hanging type floor door stopper with necessary screws, etc. complete as directed by Engineer in charge. All S.S Shall be ASIS 304 Grade.

Providing and fixing 35 mm thick shutters for Doors, windows and clerestory windows including Indian teak wood frames 12 cm x 7 cm. size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. (iii) Partly panelled and partly glazed.

Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S. flats at required spacings and frame alround, square or round bars with round headed bolts and nuts or by screws. (B) PLAIN GRILL (upto 10 ton)

Providing and fixing Fly proof galvanised M.S. wire gauge of I.S.l gauge designation 85 G. with wire of dia.0.56 mm to windows and celevating windows including 60 x 20mm beading of teak wood. (upto 10 ton)

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of read lead paint. For Wallcmpound Gate And Grill work work at above wall.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint, brushing, interior to give an even shade including cleaning the surface an even shade including cleanicn the surface of all dirt, dust and other foreign matter.

Providing upto floor two level precast cement concrete jali or grill 1:2:4 mix (1- Cement : 2- coarse sand : 4-graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia. Mild steel wire including roughening,cleaning, fixing and finishing in cement mortar 1:3 and curing complete. (D) 75mm thick

Providing material and labour for construction of Kitchen Platform made from Black Granite (16mm to 18mm thick) in top of kitchen platform rested on black kadapa stone (av.30mm thick) supported on sandwiched vertical supports of Kadapa Stone bottom of granite stone for base of platform, at required distance or as directed by Engineer-in-charge. One side vertical granite stone in geometrical shape, front granite stone patti for fascia work as well as horizontal boarders including molding and mirror polishing by hand grinder to all exposed black granite edges and providing opening of required size and shape of kitchen sink in granite and kadapa stone in line and level. The vertical supports of kadapa stone sandwiched/ gap fill up with cement mortar 1:1 and cement slurry and the granite stone vertical side and patti etc with adhesive material like Araldite etc complete as directed by Engineer-in-charge.

Providing material and labour for making BLACK GRANITE STONE COUNTER WASH BASIN of 0.60mt wide with vertical & Horizontal support of granite stone and having bottom Slab of 25mm to 30mm thick kadappa stone fixing with cement mortar 1:4 ( 1 cement :4 fine sand) and neat cement slurry as per requirement including cutting the granite stone & Providing & fixing oval shape wash basin (Make Jaquar CODE : CNS-WHT-WB02 : Under Counter Basin Size(mm) 195 x 600 x 425) white colour in line & level. All exposed Edges of granite should be moulded including all accessories , flexible inlet pipe 15mm dia, C.P brass waste coupling 32mm, PVC waste pipe 32mm etc. as directed by engineer in charge.

Providing Material, Labour and equipments for Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thickjointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : including Khurra & Gola work With average thickness of 120 mm and minimum thickness at khurra as 65 mm, etc complete as directed by engineer-incharge.

Providing and fixing Six Horizontan lines galvanised steel barbed wire weighting 9.38 Kg. per 100 Metre and One diagonals of and concentina wires respectively, strained and fixed to posts with G.I,staples including fixing the Y shape angle over compound wall etc complete.

Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(G)110 mm -spigot and socket soil, waste and ventilating pipes

Providing and fixing in position cowel went to pipes.(C) 100mm dia

Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size 580mm (Earthwork, bed concrete, foot reste and trap to be measured and paid for separately) (A) Vitreous China.(I) Long pattern = White colour

Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be measured and paid for separately)(A) vitreous China Pattern :(i) in white colour

Providing and fixing 100mm size P or S trap for water closet squatting pan including jointing the trap with the pan and soil pipe in cement Mortar 1:1 (1-Cement : 1-Fine sand)(A) Vitreous China.

Providing and fixing 12.5 Litres high level C..I. flushing cistern with A pair of C.I. or Mild steel brackets, womplete with fittings such as syplionic arrangement, 15mm nominal size brass ball valve with polythene float, lever G.I. China (60 cm. ) and pull union and couplings for connections with inlet, outlet and overflow pipes etc. including cutting holes in walls and making good the same (overflow pipe to be measured and paid fo separately )

Providing and fixing in position with clamps etc. 32mm nominal internal diameter galvanised steel tube flush pipe for high level flushing cistern including connecting the flush pipe with cistern and closet and making good the walls and floors.

Providing and fixing G.I. inlet connection for flush pipe with W.C. Pan

Providing and fixing plastic seat and cover for wash down water closer with C.P. brass hinges and rubber buffers. (B) Black plastic seal and cover.

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour.

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white including cutting holes in walls and making good the same but excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm size

Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mmdia.

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A) 100mm dia. Each

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.

Providing and fixing 600mm x 120mm glass shelf with C.P. brass bracket and guard rail complete mixed to wooden plug with C.P. brass screws.

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (i) 15mm dia.

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (ii) 20mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia.

Providing and fixing brass screw down stop tap.(B) 20mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(B) 20mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(i) 20mm dia.

Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware 550mm x 300mm.

Providing and fixing Rubber plug for sink or wash basin.

Providing and fixing chromium plated, bottle trap with necessary couplings of approved quality for wash basin.

Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (i) 25mm dia.

Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not less than 35Kg.

Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm. length.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [B] 20 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [C] 25 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [D] 32mm.

Providing erecting and fixing double coated Syntex PVC. (ISI) water tank of required capacity each with all necessary fittings and connection etc. complete on terrace.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls.

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including testing of pipes and joints complete.(B) 150mm dia. (upto 10 ton)

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(A) 100 mm dia. (112 mm Ave.bed thickness)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P type. (upto 10 ton)

Construction of B.B. Masonary Kundi of clear inside dimension size 0.60M x 0.45M x 0.45M with 23cm thick B.B. masonary wall in C:M 1:6 including required excavation, C.C. 1:5:10 15cms. Thick refilling 12mm thick cement plaster to masonary and floor C.C. layer and fixing the cast R.C.C. manhole cover of size 0.60M x 0.45M With frame and white/ colour wash etc. complete.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or two inlets. (upto 10 ton)

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(i) for 455mm x 610mm size.

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(ii) for 500mm x 700mm size.

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. (upto 10 ton)

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(D) 300mm (upto 10 ton)

Drilling of 215mm dia macked bore in loose and alluvial strata and 165mm dia bore in hard and Rocky formation by DTH Rig etc. including cleaning the bore testing of water etc. complete.

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost of rings as per IS specification No.4985/1988 incluidng all local and centra taxes, transportation, freight charges, octroi, ispection charges octroi, inspection charges loading, unloading conveyance to the departmental stores and including cost of jointing materials etc. complete for following dia and ring fit type pipe including lowering, laying and jointing PVC pipes and specials of following class and diameters including cost of labours materials exept cement solvent giving satisfactory hydraulic testing as per ISI cose etc. complete 180mm dia test pressure 6kg/CM2.

Supplying of single phase submersible pump set suitable for 100 mm size or more dia borewell having motor capacity and discharge as under with necessary pannel box (c) Motor rating 2 HP (17 stage) pump having capacity of 106 LPM at 40 mtr head suitable for 25 mm dia. delivery pipe including Supplying and erecting Direct - On - Line Starter with 18 A. rating contatctor and with 3.5 Amp. 18A range directely operated in totally insulated elegant enclosure for single phase operation upto 3 HP as per IS 13947 complete erected on P.W. Block with necessary connection.

Providing and erecting ISI marked PVC insulated PVC Shethed Flat flexible Submercible copper cable approved make of following Size. (b) 3 Core x 2.5 Sq. mm.

Providing material & labour for supplying in standarad length ISI mark high density Polyethylene HDPE pipes suiatable for potable water as per IS Specification no. 4984/1995 including all local and central taxes, transportaion, freight charges, orctroi, inspection charges, loading, unloading, conveyance to the dept. strores etc. comp. rate for HDPE (PE-100) pipe based on the rate of HDPE resin as Rs. 110292.58 (incul. of excise duty @ 12.36% but exclu. of freight and sales tax) Dtd. 1-03-2013. (b) 10.0 kg/cm2, (I) with Excise Duty 50mm dia PVC Pipe.

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.(a) with medium class Rigid PVC pipe and accessories 1.For Point wiring above 10 mtr of length, additional length will be added at rate of mains.

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.(a) with medium class Rigid PVC pipe and accessories

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories.[I] For 6A Plug with 2-1.5 sq.mm Cu. Wire(a) with medium class Rigid PVC pipe and accessories

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories.[III] For 16A Plug with 2-4 sq.mm Cu. Wire(a) with medium class Rigid PVC pipe and accessories

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed.Note:- Maximum up to 6 mtrs length, excess will be considered as Mains for Secondary Point.(a) with medium class Rigid PVC pipe and accessories

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. One No 5 pin plug

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. Blank Plate Single

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular MCB Switch

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 20 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 25 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 32 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 20 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 25 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 32 mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 2 wire 1.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 2 wire 2.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 4 wire 6 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 4 wire 10 sq. mm

Supplying & erecting M.S. Box having 16 Gauge painted with red oxide or Heavy duty PVC box erected flushed on wall or concealed in wall with necessary plastering & finishing as directed of following size.(d) 250 mm x 300 mm x 75 mm(d)

Providing & Erecting 3mm thick Polycarbonate (PC) sheet with grooving as directed

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. b).RG-6

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge TV Co-axial Socket outlet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 %, CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates )(a) Tube Light With integral/ non-integral driver, 16-18- Watts, Surge - 4KV, IP-20, 4 Feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % , CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) Tube Light With integral/ non-integral driver, 36- Watts, Surge - 4KV, IP-20, 4 Feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) LED Lamps Integral type, cool white with PC diffuser Suitable for B22 Lamp Holder, 5-8 Watts.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) LED Panel Light with provision for Plane front Frame with translucent cover fixed to housing complete. 12-15 watt, 200 x 200 mm, Surge-4 KV.

Providing and erecting Approved make Ceiling fan with double ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24/0.2 , 3 core flexible wire with earthing. [Make shall be approved by Engineer in charge]

Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with condenser A.C.230V 50c/s. 1400 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24 / 0.2, 3 core flexible Copper wire with earthing [ Make shall be approved by Engineer in Charge]

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in RCC slab with Making the site as original.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with necessary finishing.

Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. Bolt & Nuts erected with necessary hook of 10 mm M.S. Round Bar.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box.

Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square frame ABS body with inbuilt lowers & square frame.

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM, 305 mm dia 900 RPM

Providing suitable M.S. louver shutter of the Exhaust fan.

Providing recess in wall or window frame suitable for erection of Exhaust fan complete with plastering and colour washing to match the colour of the wall or window complete with expanded metal in order to render the fitting in accessible and the room water-proof.

Providing window frame suitable for erection of Exhaust fan complete covering the remaining portion of window with 15 mm. thick plywood and colour washing to match the colour of the wall.

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Single phase 4 way SS Double door

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Single phase 8 way SS Double door

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Three phase 6 way SS Double door for single phase outgoing horizontal box

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Single Phase 4 Way

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Single Phase 8 Way

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Three Phase 6 Way

The Above all items of MCB, DB the cost of erection on New angle iron frame add following.up to 8 way single phase

The Above all items of MCB, DB the cost of erection on New angle iron frame add following.above single phase 8 way and all three phase DBs.

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 25 Amps.DP

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 40 Amps.DP

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on 3 phase and neutral 415V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component for following Max. rating erected as directed. 40Amps. FP

Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 6 to 32 Amp.

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 40 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 6 to 32 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 40 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 63 Amp.

Approved make Three Phase & Neutral LT Heavy Duty Switch Disconnector Fuse Unit Cubical type for panel mounting complete with operating mechanism suitable to operate on 415V A.C. , 23A duty With HRC fuses of suitable load confirming to IS. 13947 (Part I & III). of following capacities.100Amp/125 Amp

Cable Terminal ( ‘Plain" Type)Set of Four for 32 / 63 Amps

Cable Terminal ( ‘Plain" Type)Set of Four for 125/200 Amps

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting Aluminium Busbars with four equal Nos. of bus having current density not more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket to each busbar,erected in existing cubical panel with necessary connections. Suitable for 200 Amp. Capacity

Supplying and erecting approved make 415V bakelite fuse fittings for front connection / busbar type, to accommodate HRC fuse link, with spin - riveted brass contact, having thermo plastic inflammable material & single piece extruded brass box contact to lock with adequate cable hole to accommodate aluminium conductors suitable for (without HRC fuse) 16 Amp.

Supplying Bolted Connections (BS type) HRC fuse link capable to withstand 80KA confirms to I.S. 13703 for following current capacity up to 32 Amp.

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board having IP-64 protection made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary supporting angles, flats including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge with erection of supplied switch gears, BUSBARS, with suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses for measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket complete. The Panel shall be painted with epoxy powder coating. (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following approved manufacturers with following size.(A) The standard companies switch gear shall be used and only manufacturers at CPRI approved factory and shall be certified by that company whose switch gears are used after fabrication for beneficial use with 350mm depth

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using proper clamp.

Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For panel)

For using salt and charcoal / coke as required for pipe type earthing.

Add Extra for excavation in Hard rock by dry and wet blasting and chiselling for pipe type earthing.

Supplying and erecting LED Street Light/Flood light fittings with High power White LED's wattage of 1 watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminium housing with smooth finish powder coated and heatsink extruded aluminium with diffuser and Polycarbonate optics/lenses with company mark/name engraved or embossed 120 to 300 V, Power Factor more than 0.95, THD less Than 10% CCT 5000 K to 5700 K, Uniformality ratio >0.45, Luminaire efficiancy > 85 lumen/watt, LED driver efficiancy > 85 %. CREE/OSRAM/PHILIPS Lumileds/NICHIA/SEOUL/Bridge Lux ( U.S.A.) make LED used for luminaire. ( Each fittings required LM-79 & LM-80 Certificates) Flood Light (IP-65), Surge- 4 KV Above 70 watts to 90 watts

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

Making trench in Hard Murrum / Tar Road of suitable width of 90 cms or required depth for laying any size of cable or locating the fault all over the run and back filling the same and making the surface as normal ground.

(B) If additional machineries like hammer driller or JCB use [Add]

Covering of cable with second class bricks or cement tiles laid cover the cable crosswise & also on both sides with covering of 7. 5 Cms. layer of sand above & below cable (16 bricks per meter)

Providing and erecting iron clad cable route marker duly marked with ELE.CABLE of size 23 cms.X 12 cms. Flushed with ground in cement foundation as directed by Engineer in charge.

Supplying following size of Light duty “A” Class G.I . Pipe & erecting as directed by Engineer-in-charge. 50 mm dia

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. 2 to 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. 3 & 1/2 core 70 Sq. mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 1.5/ 2.5/4/6 Sq.mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 70 Sq.mm.

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 35/50 Sq.mm.

Providing and erecting 18 G. M.S. termination box outdoor type suitable for- 1.1 KV PVC insulated armoured cable complete erected with clamp, bolts, nuts etc. suitable of following size of cables.3 core 70 / 95 Sq. mm

Providing and erecting Epoxy Outdoor / Indoor end termination Kit suitable for LT PVC insulated armoured cable1.1 KV grade complete with ferrule bushing and accessories and suitable clamps duly erected and connected to the supply for all cores cables of following size. 2.5 to 16 Sq. mm

Providing and erecting Epoxy Outdoor / Indoor end termination Kit suitable for LT PVC insulated armoured cable1.1 KV grade complete with ferrule bushing and accessories and suitable clamps duly erected and connected to the supply for all cores cables of following size. 70 to 120 Sq. mm

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame, prefilter housing with 'O' ring presediment filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40 Osg inline type post carbon filter auto low & high pressure switches with following size of storage tank & LPH capacity & erected as directed with one year comprehensive maintenance guarantee. [B] 25 Ltr / Hr with 30 Ltr. S.S. Pressure Tank

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 45°C. The outlet temp. of the water should drop by 15°C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating, coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.

Conveyance charges including loading / unloading for Water Cooler from store to site (ii) Outside Divisional Head Quarter for first 60 Km from store.

Supplying & erecting Galvanized iron pipe post “B” class 88.9 mm O.D 6 mtr. Long duly painted with two coats of aluminium paint complete with metallic base- plate of 300 mm x 300 mm x 4mm thick for using as a compound light pole with approx. weight 47 Kg.

Providing M-20 / 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of size 45 x 45 x 100 cms. Deep in below ground level with plinth of 45 cms x 45 cms (or 45 cms dia x 45 cms) high upper ground level with necessary curing and finishing in approved manner. ( for 4 & 6 mtr pole)

Fabricating terminal box for street light pole made from 16 SWG M.S. sheet having following size complete with fixing arrangement for terminal board, with necessary hole for wire entry and exit from the box. The box shall be provided with cover and hinges on one side and bolting at other end The box shall be fixed by clamps fabricated from 25mm x 6mm flat.The box shall be painted with one coat of red oxide and two coats of paint having following box size. 330 mm x 260 mm x 140 mm (depth)

Providing street light pole bracket comprising main Light Class MS tube of 4.2 cms. outside dia. complete with suitable M.S. sleeve tubing of approx. 45cms.length and suitable for 76.5mm. /80 mm or require size pole top having sufficient fastners for fixing the brackets and having suitable rise as per site condition as directed and spread of 2 mtr.with suitable welded stiffener reducer and with lock nut complete painted with one coat of Red oxide / PU base primer and two coats of Aluminium / PU paint. Suitable for side entry fitting brackets of following nos of arms.Single Arm bracket 2 Mtr

Supplying and erecting LED Street Light/Flood light fittings with High power White LED's wattage of 1 watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminium housing with smooth finish powder coated and heatsink extruded aluminium with diffuser and Polycarbonate optics/lenses with company mark/name engraved or embossed 120 to 300 V, Power Factor more than 0.95, THD less Than 10% CCT 5000 K to 5700 K, Uniformality ratio >0.45, Luminaire efficiancy > 85 lumen/watt, LED driver efficiancy > 85 %. CREE/OSRAM/PHILIPS Lumileds/NICHIA/SEOUL/Bridge Lux ( U.S.A.) make LED used for luminaire. ( Each fittings required LM-79 & LM-80 Certificates) Street Light (IP-65), Surge- 4 KV Above 48 watts to 60 watts Cat III

Mandoni

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and stacking of useful materials and disposing of the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Providing material and labour for filling in plinth etc WITH UNSCREEN GRAVEL under floors including watering, ramming consolidating and dressing etc. complete.

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each disposited layer by ramming and watering.

Providing material and labour for injecting Chemical emulsion for PRE - CONSTRUCTIONAL anti-termite treatment and creating a chemical barrier on the top surface of plinth filling, inside junction of wall and floor, on top of damp proof course (DPC) or on masonry at level of plinth filling as per IS 6313 (Part-2)-1981 using chemical like chloropyripos emulsifiable, Biflex TC, lindane (IS 8944-1978) 20EC mixed with water in 1:19 ratio (1 liter chemical : 19 liters of water). The emulsion shall mentioned below, all as per specification and directions of Engineer-in-charge. Plinth area in plan at GF shall only be measured (for akk below specified steps) and paid. A guarantee bond of 10 years shall be furnished. A1) Bottom surface and the sides of the excavation made for masonry foundations at the rate of 4 liters/sqm (wherever applicable) A2) At the rate of 7.5 liter/ sqm to the backfill at the depth of 500mm below the original ground level. The soil in the immediate contact with the vertical surface of RCC column/ Masonry shall be treated. B) Top surface of the plinth filling including damp proof courses at the rate of 5 liter/sqm of internal plinth area etc. complete. C) At the rate of 7.5 liter/ sqm to the internal vertical surface from original Ground level to top of the earth filled in the plinth. D) At the rate of 7.5 liter/ sqm to the external vertical surface below finished Ground level to the full depth of the filling complete. E) 1 liter / linear meter along the junction of wall and floor at all stages.

Providing material and labour for laying Autoclave Aerated Concrete Block chips/ bats cement mortar in 1:6 (1 Cement : 6 Coarse Sand) with Autoclave Aerated Concrete Block chips/ bats for sunk filling grade including compacting, finishing, curing etc. complete as directed by engineer in charge.

Filling in foundation and plinth with brick bats Chhara in layers of 20 cm thickness including watering, ramming and consolidating etc. complete.

Providing and laying PLINTH PROTECTION including excavation of 30cm. Depth and filling with Brick bats of 20cm. Thick and C.C. 1:2:4 ( 1 cement :2 coarse and :4 graded stone aggregate 40mm nominal size) of 10cm. Thick and top layers of C.C. 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregates 20mm. Nominal size ) of 50mm, thick including finishing top surface with floating coat of neat cement slurry.

Providing material and labour for laying Plain cement concrete M15 in Foundation and Plinth including cost of formwork, compacting, finishing, curing etc complete for all level, all height/ depth as directed by engineer in charge.

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in (A) Foundations, footings, Base of columns and Mass concrete. (upto 10 ton)

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. Height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ reinforced concrete and plain concrete work in. (A) Foundations Footings Bases of Columns etc. and Mass concrete. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts, upto floor two level. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts, Above floor two level & upto Level Three. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever upto floor two level etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever above floor two level upto floor three level etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.200 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (C) Slabs,landing,shelves,Balconies Lintels, Beams, Girders and Cantilever upto floor two level. (more than 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in (C) Slabs, landing, shelves and Cantilever upto floor two level, etc complete as directed by engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in (C) Slabs, landing, shelves and Cantilever above floor two level upto floor three level etc complete as directed by engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (B) Walls, from top of foundation level upto floor two level (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding the cost of reinforcement for reinforced concrete work in (E) Staircases upto floor two level, etc complete as directed by engineer-incharge.

Providing material and labour for laying Controlled cement concert M-250 and curing complete including cost of Form work with steel sheating sheet etc. excluding the cost of reinforcement of reinforced concrete work the in STAIRCASE ABOVE FLOOR TWO LEVEL UPTO FLOOR THREE LEVEL.

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level (upto 10 ton)

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including bending, binding and placing in position complete Above floor two level & upto Level Three

Providing, Suppying and mixing Dr. Fixit water proofing materials in cemrnt concrete in proportion I.e. 200ml for 50 Kg of 1 cement bag, Or recommended by the manufacturer. It is to be mix in wet concrete.

(ii) Uncoursed Rubble Masonry with hard stone of approved quality in foundations and plinth in Cement Mortar 1:5 (1-cement : 5-coarse sand including levelling up etc. complete (more than 10 ton)

(ii) Uncoursed Rubble Masonry with hard stone of approved quality in Above plinth level upto floor level two in Cement Mortar 1:5 (1-cement : 5-coarse sand including levelling up etc. complete (more than 10 ton)

(ii) Uncoursed Rubble Masonry with hard stone of approved quality in Above floor two level in Cement Mortar 1:5 (1-cement : 5-coarse sand including levelling up etc. complete (more than 10 ton)

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in Above plinth level upto floor level two in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in Above floor two leve in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Half brick thick honey- comb brick work with common burnt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. (i) In Cement Mortar 1:4 ( 1- Cement : 4 - coarse sand) (upto 10 ton)

Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:3 ( 1-Cement : 3-coarse sand ) with 2 Nos of 6mm Mild steel round bars after every three course embedded in Cement Mortar inAbove plinth level upto floor level two (B) Conventional (upto 10 ton)

Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:3 ( 1-Cement : 3-coarse sand ) with 2 Nos of 6mm Mild steel round bars after every three course embedded in Cement Mortar in Above floor two level (B) Conventional (upto 10 ton)

Providing material and labour for 6mm thick CEMENT PLASTER in single Coat For plastering on ceiling and soffits of stairs UPTO FLOOR TWO LEVEL & ABOVE finished even and smooth including curing etc. complete in C:M 1:3 (1 cement :3 fine sand) and finishing with floating coat of neat cement slurry.

Providing material and labour for 12mm thick CEMENT PLASTER in Single Coat For plastering on Brick concrete wall surfaces for plastering UPTO FLOOR TWO LEVEL & ABOVE finished even and smooth including curing etc. complete in C:M 1:3 (1 cement :3 fine sand) and finishing with floating coat of neat cement slurry.

Providing 20mm thick cement plaster in double coat on single or half brick walls for interior plastering upto floor two level & above two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) finishing with floating coat of neat cement slurry.

Pointing on Uncoursed stone masonry with cement mortar 1:3 (1-cement : 3-coarse sand)(B) Ruled pointing

Providing material and labour for fixing polished kota stone slab flooring 20 mm (average) thick base of cemetn mortar 1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing etc. complete (A) 25 mm thick.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on existing flooring by adhesive material including dismentaling of existing flooring and jointed with color cement slurry including finised with flush pointing & cleaning the surface etc, Including cost of material & labour for fixing spacer, epoxy grouting for filling in joints between tiles. complete for antiskit (upto 10 ton)

Providing and laying coloured glazed tiles of the size 300 mm x 200 mm x 8 mm / 300 mm x 450 mm x 8 mm in skirting, risers of steps and dedo on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with white cement slurry.

Providing and fixing 18 mm thick Granite of any colour and shade gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing and laying chequered precast cement concrete tiles 22mm thick with aggegate of sizes upto 6mm in floors, treads of steps and landings on 20mm thick bed of C.M. 1:6 (1-cement : 6-sand) or L.M. 1:1.5(1-Lime putty : 1.5 coarse sand) joint with neat cement slurry with pigments to match the shade of the tiles. (upto 10 ton)

Providing and fixing tiles roofing with manglore tiles including cement mortar of 1:4 ratio over Sloping RCC slab roof.

Providing and fixing 150mm wide 450mm over all semicircular plain G.I.sheet class-3 gutter with Iron brackets 40mm x 3mm size Bolts, Nuts, washers etc. including making necessary connection with rain water pipes. (i) 0.80 mm thick Sheet. (upto 10 ton)

Providing and fixing 1000mm high stainless steel railing consisting of 50mm dia round SS pipe hand rail supported on 75mm high 25mm x 25mm X 2mm square SS pipe fixed to about 875mm high 38mm x 38mm square SS pipe balustrades placed about 900mm centre to centre. Each balustrade is to be secured by 4 Nos. M8 x 100 fasteners of hilti or any other approved equivalent make and covered with 75mm x 8mm thick base plate with cap. Stainless steel to be Minimum 16 gauge of SS 304 grade complete in all respects as approved by Architect/ Engineer-in-charge.

Distempeing (Two coats) with oil bound distemper of approved brand and manufacture and of required shade on wall surfaces to give an even shade, over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth.

Finishing wall with water proofing cement paint of on wall surfaces (Two coats) to give an approved brand and manufacture and of required shape even shade after thoroughly brushing the surface to remove all dirt and remains of loose powered materials.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete

Finishing Stone masonary wall with Asian make PU paint coating on stone surface to give an required shade after thoroughly brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing material and labour for fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws, with Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS :2046 Type S, including cost of adhesive of approved quality 1.0mm Thick on both face, with Providing and fixing S.S. tower bolts (barrel type) with necessary screws etc 200mm long x10mm dia, with Providing and fixing S.S. Door Aldrop with necessary screws etc. 300mm long x16mm dia, Providing and fixing S.S. Door Aldrop with necessary screws etc 250mm long x16mm dia, with Providing and fixing S.S. Pipe Handle for door 30cm size on both side of Door shutter, with Providing and fixing S.S hanging type floor door stopper with necessary screws, etc. complete as directed by Engineer in charge. All S.S Shall be ASIS 304 Grade.

Providing and fixing 35 mm thick shutters for Doors, windows and clerestory windows including Indian teak wood frames 12 cm x 7 cm. size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. (iii) Partly panelled and partly glazed.

Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S. flats at required spacings and frame alround, square or round bars with round headed bolts and nuts or by screws. (B) PLAIN GRILL (upto 10 ton)

Providing and fixing Fly proof galvanised M.S. wire gauge of I.S.l gauge designation 85 G. with wire of dia.0.56 mm to windows and celevating windows including 60 x 20mm beading of teak wood. (upto 10 ton)

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of read lead paint. For Wallcmpound Gate And Grill work work at above wall.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint, brushing, interior to give an even shade including cleaning the surface an even shade including cleanicn the surface of all dirt, dust and other foreign matter.

Providing upto floor two level precast cement concrete jali or grill 1:2:4 mix (1- Cement : 2- coarse sand : 4-graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia. Mild steel wire including roughening,cleaning, fixing and finishing in cement mortar 1:3 and curing complete. (D) 75mm thick

Providing material and labour for construction of Kitchen Platform made from Black Granite (16mm to 18mm thick) in top of kitchen platform rested on black kadapa stone (av.30mm thick) supported on sandwiched vertical supports of Kadapa Stone bottom of granite stone for base of platform, at required distance or as directed by Engineer-in-charge. One side vertical granite stone in geometrical shape, front granite stone patti for fascia work as well as horizontal boarders including molding and mirror polishing by hand grinder to all exposed black granite edges and providing opening of required size and shape of kitchen sink in granite and kadapa stone in line and level. The vertical supports of kadapa stone sandwiched/ gap fill up with cement mortar 1:1 and cement slurry and the granite stone vertical side and patti etc with adhesive material like Araldite etc complete as directed by Engineer-in-charge.

Providing material and labour for making BLACK GRANITE STONE COUNTER WASH BASIN of 0.60mt wide with vertical & Horizontal support of granite stone and having bottom Slab of 25mm to 30mm thick kadappa stone fixing with cement mortar 1:4 ( 1 cement :4 fine sand) and neat cement slurry as per requirement including cutting the granite stone & Providing & fixing oval shape wash basin (Make Jaquar CODE : CNS-WHT-WB02 : Under Counter Basin Size(mm) 195 x 600 x 425) white colour in line & level. All exposed Edges of granite should be moulded including all accessories , flexible inlet pipe 15mm dia, C.P brass waste coupling 32mm, PVC waste pipe 32mm etc. as directed by engineer in charge.

Providing Material, Labour and equipments for Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thickjointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : including Khurra & Gola work With average thickness of 120 mm and minimum thickness at khurra as 65 mm, etc complete as directed by engineer-incharge.

Providing and fixing Six Horizontan lines galvanised steel barbed wire weighting 9.38 Kg. per 100 Metre and One diagonals of and concentina wires respectively, strained and fixed to posts with G.I,staples including fixing the Y shape angle over compound wall etc complete.

Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(G)110 mm -spigot and socket soil, waste and ventilating pipes

Providing and fixing in position cowel went to pipes.(C) 100mm dia

Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size 580mm (Earthwork, bed concrete, foot reste and trap to be measured and paid for separately) (A) Vitreous China.(I) Long pattern = White colour

Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be measured and paid for separately)(A) vitreous China Pattern :(i) in white colour

Providing and fixing 100mm size P or S trap for water closet squatting pan including jointing the trap with the pan and soil pipe in cement Mortar 1:1 (1-Cement : 1-Fine sand)(A) Vitreous China.

Providing and fixing 12.5 Litres high level C..I. flushing cistern with A pair of C.I. or Mild steel brackets, womplete with fittings such as syplionic arrangement, 15mm nominal size brass ball valve with polythene float, lever G.I. China (60 cm. ) and pull union and couplings for connections with inlet, outlet and overflow pipes etc. including cutting holes in walls and making good the same (overflow pipe to be measured and paid fo separately )

Providing and fixing in position with clamps etc. 32mm nominal internal diameter galvanised steel tube flush pipe for high level flushing cistern including connecting the flush pipe with cistern and closet and making good the walls and floors.

Providing and fixing G.I. inlet connection for flush pipe with W.C. Pan

Providing and fixing plastic seat and cover for wash down water closer with C.P. brass hinges and rubber buffers. (B) Black plastic seal and cover.

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour.

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white including cutting holes in walls and making good the same but excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm size

Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mmdia.

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A) 100mm dia. Each

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.

Providing and fixing 600mm x 120mm glass shelf with C.P. brass bracket and guard rail complete mixed to wooden plug with C.P. brass screws.

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (i) 15mm dia.

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (ii) 20mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia.

Providing and fixing brass screw down stop tap.(B) 20mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(B) 20mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(i) 20mm dia.

Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware 550mm x 300mm.

Providing and fixing Rubber plug for sink or wash basin.

Providing and fixing chromium plated, bottle trap with necessary couplings of approved quality for wash basin.

Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (i) 25mm dia.

Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not less than 35Kg.

Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm. length.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [B] 20 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [C] 25 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [D] 32mm.

Providing erecting and fixing double coated Syntex PVC. (ISI) water tank of required capacity each with all necessary fittings and connection etc. complete on terrace.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls.

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including testing of pipes and joints complete.(B) 150mm dia. (upto 10 ton)

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(A) 100 mm dia. (112 mm Ave.bed thickness)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P type. (upto 10 ton)

Construction of B.B. Masonary Kundi of clear inside dimension size 0.60M x 0.45M x 0.45M with 23cm thick B.B. masonary wall in C:M 1:6 including required excavation, C.C. 1:5:10 15cms. Thick refilling 12mm thick cement plaster to masonary and floor C.C. layer and fixing the cast R.C.C. manhole cover of size 0.60M x 0.45M With frame and white/ colour wash etc. complete.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or two inlets. (upto 10 ton)

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(i) for 455mm x 610mm size.

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(ii) for 500mm x 700mm size.

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. (upto 10 ton)

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(D) 300mm (upto 10 ton)

Drilling of 215mm dia macked bore in loose and alluvial strata and 165mm dia bore in hard and Rocky formation by DTH Rig etc. including cleaning the bore testing of water etc. complete.

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost of rings as per IS specification No.4985/1988 incluidng all local and centra taxes, transportation, freight charges, octroi, ispection charges octroi, inspection charges loading, unloading conveyance to the departmental stores and including cost of jointing materials etc. complete for following dia and ring fit type pipe including lowering, laying and jointing PVC pipes and specials of following class and diameters including cost of labours materials exept cement solvent giving satisfactory hydraulic testing as per ISI cose etc. complete 180mm dia test pressure 6kg/CM2.

Supplying of single phase submersible pump set suitable for 100 mm size or more dia borewell having motor capacity and discharge as under with necessary pannel box (c) Motor rating 2 HP (17 stage) pump having capacity of 106 LPM at 40 mtr head suitable for 25 mm dia. delivery pipe including Supplying and erecting Direct - On - Line Starter with 18 A. rating contatctor and with 3.5 Amp. 18A range directely operated in totally insulated elegant enclosure for single phase operation upto 3 HP as per IS 13947 complete erected on P.W. Block with necessary connection.

Providing and erecting ISI marked PVC insulated PVC Shethed Flat flexible Submercible copper cable approved make of following Size. (b) 3 Core x 2.5 Sq. mm.

Providing material & labour for supplying in standarad length ISI mark high density Polyethylene HDPE pipes suiatable for potable water as per IS Specification no. 4984/1995 including all local and central taxes, transportaion, freight charges, orctroi, inspection charges, loading, unloading, conveyance to the dept. strores etc. comp. rate for HDPE (PE-100) pipe based on the rate of HDPE resin as Rs. 110292.58 (incul. of excise duty @ 12.36% but exclu. of freight and sales tax) Dtd. 1-03-2013. (b) 10.0 kg/cm2, (I) with Excise Duty 50mm dia PVC Pipe.

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.(a) with medium class Rigid PVC pipe and accessories 1.For Point wiring above 10 mtr of length, additional length will be added at rate of mains.

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.(a) with medium class Rigid PVC pipe and accessories

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories.[I] For 6A Plug with 2-1.5 sq.mm Cu. Wire(a) with medium class Rigid PVC pipe and accessories

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories.[III] For 16A Plug with 2-4 sq.mm Cu. Wire(a) with medium class Rigid PVC pipe and accessories

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed.Note:- Maximum up to 6 mtrs length, excess will be considered as Mains for Secondary Point.(a) with medium class Rigid PVC pipe and accessories

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. One No 5 pin plug

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. Blank Plate Single

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular MCB Switch

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 20 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 25 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 32 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 20 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 25 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 32 mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 2 wire 1.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 2 wire 2.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 4 wire 6 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 4 wire 10 sq. mm

Supplying & erecting M.S. Box having 16 Gauge painted with red oxide or Heavy duty PVC box erected flushed on wall or concealed in wall with necessary plastering & finishing as directed of following size.(d) 250 mm x 300 mm x 75 mm(d)

Providing & Erecting 3mm thick Polycarbonate (PC) sheet with grooving as directed

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. b).RG-6

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge TV Co-axial Socket outlet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 %, CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates )(a) Tube Light With integral/ non-integral driver, 16-18- Watts, Surge - 4KV, IP-20, 4 Feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % , CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) Tube Light With integral/ non-integral driver, 36- Watts, Surge - 4KV, IP-20, 4 Feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) LED Lamps Integral type, cool white with PC diffuser Suitable for B22 Lamp Holder, 5-8 Watts.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) LED Panel Light with provision for Plane front Frame with translucent cover fixed to housing complete. 12-15 watt, 200 x 200 mm, Surge-4 KV.

Providing and erecting Approved make Ceiling fan with double ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24/0.2 , 3 core flexible wire with earthing. [Make shall be approved by Engineer in charge]

Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with condenser A.C.230V 50c/s. 1400 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24 / 0.2, 3 core flexible Copper wire with earthing [ Make shall be approved by Engineer in Charge]

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in RCC slab with Making the site as original.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with necessary finishing.

Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. Bolt & Nuts erected with necessary hook of 10 mm M.S. Round Bar.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box.

Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square frame ABS body with inbuilt lowers & square frame.

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM, 305 mm dia 900 RPM

Providing suitable M.S. louver shutter of the Exhaust fan.

Providing recess in wall or window frame suitable for erection of Exhaust fan complete with plastering and colour washing to match the colour of the wall or window complete with expanded metal in order to render the fitting in accessible and the room water-proof.

Providing window frame suitable for erection of Exhaust fan complete covering the remaining portion of window with 15 mm. thick plywood and colour washing to match the colour of the wall.

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Single phase 4 way SS Double door

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Single phase 8 way SS Double door

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Three phase 6 way SS Double door for single phase outgoing horizontal box

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Single Phase 4 Way

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Single Phase 8 Way

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Three Phase 6 Way

The Above all items of MCB, DB the cost of erection on New angle iron frame add following.up to 8 way single phase

The Above all items of MCB, DB the cost of erection on New angle iron frame add following.above single phase 8 way and all three phase DBs.

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 25 Amps.DP

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 40 Amps.DP

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on 3 phase and neutral 415V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component for following Max. rating erected as directed. 40Amps. FP

Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 6 to 32 Amp.

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 40 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 6 to 32 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 40 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 63 Amp.

Approved make Three Phase & Neutral LT Heavy Duty Switch Disconnector Fuse Unit Cubical type for panel mounting complete with operating mechanism suitable to operate on 415V A.C. , 23A duty With HRC fuses of suitable load confirming to IS. 13947 (Part I & III). of following capacities.100Amp/125 Amp

Cable Terminal ( ‘Plain" Type)Set of Four for 32 / 63 Amps

Cable Terminal ( ‘Plain" Type)Set of Four for 125/200 Amps

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting Aluminium Busbars with four equal Nos. of bus having current density not more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket to each busbar,erected in existing cubical panel with necessary connections. Suitable for 200 Amp. Capacity

Supplying and erecting approved make 415V bakelite fuse fittings for front connection / busbar type, to accommodate HRC fuse link, with spin - riveted brass contact, having thermo plastic inflammable material & single piece extruded brass box contact to lock with adequate cable hole to accommodate aluminium conductors suitable for (without HRC fuse) 16 Amp.

Supplying Bolted Connections (BS type) HRC fuse link capable to withstand 80KA confirms to I.S. 13703 for following current capacity up to 32 Amp.

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board having IP-64 protection made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary supporting angles, flats including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge with erection of supplied switch gears, BUSBARS, with suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses for measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket complete. The Panel shall be painted with epoxy powder coating. (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following approved manufacturers with following size.(A) The standard companies switch gear shall be used and only manufacturers at CPRI approved factory and shall be certified by that company whose switch gears are used after fabrication for beneficial use with 350mm depth

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using proper clamp.

Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For panel)

For using salt and charcoal / coke as required for pipe type earthing.

Add Extra for excavation in Hard rock by dry and wet blasting and chiselling for pipe type earthing.

Supplying and erecting LED Street Light/Flood light fittings with High power White LED's wattage of 1 watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminium housing with smooth finish powder coated and heatsink extruded aluminium with diffuser and Polycarbonate optics/lenses with company mark/name engraved or embossed 120 to 300 V, Power Factor more than 0.95, THD less Than 10% CCT 5000 K to 5700 K, Uniformality ratio >0.45, Luminaire efficiancy > 85 lumen/watt, LED driver efficiancy > 85 %. CREE/OSRAM/PHILIPS Lumileds/NICHIA/SEOUL/Bridge Lux ( U.S.A.) make LED used for luminaire. ( Each fittings required LM-79 & LM-80 Certificates) Flood Light (IP-65), Surge- 4 KV Above 70 watts to 90 watts

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

Making trench in Hard Murrum / Tar Road of suitable width of 90 cms or required depth for laying any size of cable or locating the fault all over the run and back filling the same and making the surface as normal ground.

(B) If additional machineries like hammer driller or JCB use [Add]

Covering of cable with second class bricks or cement tiles laid cover the cable crosswise & also on both sides with covering of 7. 5 Cms. layer of sand above & below cable (16 bricks per meter)

Providing and erecting iron clad cable route marker duly marked with ELE.CABLE of size 23 cms.X 12 cms. Flushed with ground in cement foundation as directed by Engineer in charge.

Supplying following size of Light duty “A” Class G.I . Pipe & erecting as directed by Engineer-in-charge. 50 mm dia

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. 2 to 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. 3 & 1/2 core 70 Sq. mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 1.5/ 2.5/4/6 Sq.mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 70 Sq.mm.

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 35/50 Sq.mm.

Providing and erecting 18 G. M.S. termination box outdoor type suitable for- 1.1 KV PVC insulated armoured cable complete erected with clamp, bolts, nuts etc. suitable of following size of cables.3 core 70 / 95 Sq. mm

Providing and erecting Epoxy Outdoor / Indoor end termination Kit suitable for LT PVC insulated armoured cable1.1 KV grade complete with ferrule bushing and accessories and suitable clamps duly erected and connected to the supply for all cores cables of following size. 2.5 to 16 Sq. mm

Providing and erecting Epoxy Outdoor / Indoor end termination Kit suitable for LT PVC insulated armoured cable1.1 KV grade complete with ferrule bushing and accessories and suitable clamps duly erected and connected to the supply for all cores cables of following size. 70 to 120 Sq. mm

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame, prefilter housing with 'O' ring presediment filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40 Osg inline type post carbon filter auto low & high pressure switches with following size of storage tank & LPH capacity & erected as directed with one year comprehensive maintenance guarantee. [B] 25 Ltr / Hr with 30 Ltr. S.S. Pressure Tank

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 45°C. The outlet temp. of the water should drop by 15°C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating, coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.

Conveyance charges including loading / unloading for Water Cooler from store to site (ii) Outside Divisional Head Quarter for first 60 Km from store.

Supplying & erecting Galvanized iron pipe post “B” class 88.9 mm O.D 6 mtr. Long duly painted with two coats of aluminium paint complete with metallic base- plate of 300 mm x 300 mm x 4mm thick for using as a compound light pole with approx. weight 47 Kg.

Providing M-20 / 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of size 45 x 45 x 100 cms. Deep in below ground level with plinth of 45 cms x 45 cms (or 45 cms dia x 45 cms) high upper ground level with necessary curing and finishing in approved manner. ( for 4 & 6 mtr pole)

Fabricating terminal box for street light pole made from 16 SWG M.S. sheet having following size complete with fixing arrangement for terminal board, with necessary hole for wire entry and exit from the box. The box shall be provided with cover and hinges on one side and bolting at other end The box shall be fixed by clamps fabricated from 25mm x 6mm flat.The box shall be painted with one coat of red oxide and two coats of paint having following box size. 330 mm x 260 mm x 140 mm (depth)

Providing street light pole bracket comprising main Light Class MS tube of 4.2 cms. outside dia. complete with suitable M.S. sleeve tubing of approx. 45cms.length and suitable for 76.5mm. /80 mm or require size pole top having sufficient fastners for fixing the brackets and having suitable rise as per site condition as directed and spread of 2 mtr.with suitable welded stiffener reducer and with lock nut complete painted with one coat of Red oxide / PU base primer and two coats of Aluminium / PU paint. Suitable for side entry fitting brackets of following nos of arms.Single Arm bracket 2 Mtr

Supplying and erecting LED Street Light/Flood light fittings with High power White LED's wattage of 1 watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminium housing with smooth finish powder coated and heatsink extruded aluminium with diffuser and Polycarbonate optics/lenses with company mark/name engraved or embossed 120 to 300 V, Power Factor more than 0.95, THD less Than 10% CCT 5000 K to 5700 K, Uniformality ratio >0.45, Luminaire efficiancy > 85 lumen/watt, LED driver efficiancy > 85 %. CREE/OSRAM/PHILIPS Lumileds/NICHIA/SEOUL/Bridge Lux ( U.S.A.) make LED used for luminaire. ( Each fittings required LM-79 & LM-80 Certificates) Street Light (IP-65), Surge- 4 KV Above 48 watts to 60 watts Cat III

Randha

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and stacking of useful materials and disposing of the excavated stuff upto safe disposal site as directed by Engineer-in-charge (C) Hard Murrum

Providing material and labour for filling in plinth etc WITH UNSCREEN GRAVEL under floors including watering, ramming consolidating and dressing etc. complete.

Filling available excavated earth (excluding rock) in trenches. plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each disposited layer by ramming and watering.

Providing material and labour for injecting Chemical emulsion for PRE - CONSTRUCTIONAL anti-termite treatment and creating a chemical barrier on the top surface of plinth filling, inside junction of wall and floor, on top of damp proof course (DPC) or on masonry at level of plinth filling as per IS 6313 (Part-2)-1981 using chemical like chloropyripos emulsifiable, Biflex TC, lindane (IS 8944-1978) 20EC mixed with water in 1:19 ratio (1 liter chemical : 19 liters of water). The emulsion shall mentioned below, all as per specification and directions of Engineer-in-charge. Plinth area in plan at GF shall only be measured (for akk below specified steps) and paid. A guarantee bond of 10 years shall be furnished. A1) Bottom surface and the sides of the excavation made for masonry foundations at the rate of 4 liters/sqm (wherever applicable) A2) At the rate of 7.5 liter/ sqm to the backfill at the depth of 500mm below the original ground level. The soil in the immediate contact with the vertical surface of RCC column/ Masonry shall be treated. B) Top surface of the plinth filling including damp proof courses at the rate of 5 liter/sqm of internal plinth area etc. complete. C) At the rate of 7.5 liter/ sqm to the internal vertical surface from original Ground level to top of the earth filled in the plinth. D) At the rate of 7.5 liter/ sqm to the external vertical surface below finished Ground level to the full depth of the filling complete. E) 1 liter / linear meter along the junction of wall and floor at all stages.

Providing material and labour for laying Autoclave Aerated Concrete Block chips/ bats cement mortar in 1:6 (1 Cement : 6 Coarse Sand) with Autoclave Aerated Concrete Block chips/ bats for sunk filling grade including compacting, finishing, curing etc. complete as directed by engineer in charge.

Filling in foundation and plinth with brick bats Chhara in layers of 20 cm thickness including watering, ramming and consolidating etc. complete.

Providing and laying PLINTH PROTECTION including excavation of 30cm. Depth and filling with Brick bats of 20cm. Thick and C.C. 1:2:4 ( 1 cement :2 coarse and :4 graded stone aggregate 40mm nominal size) of 10cm. Thick and top layers of C.C. 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregates 20mm. Nominal size ) of 50mm, thick including finishing top surface with floating coat of neat cement slurry.

Providing material and labour for laying Plain cement concrete M15 in Foundation and Plinth including cost of formwork, compacting, finishing, curing etc complete for all level, all height/ depth as directed by engineer in charge.

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in (A) Foundations, footings, Base of columns and Mass concrete. (upto 10 ton)

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering strutting and propping etc. Height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ reinforced concrete and plain concrete work in. (A) Foundations Footings Bases of Columns etc. and Mass concrete. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts, upto floor two level. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in Lintels, Beams, Girders and Cantilever upto floor two level etc complete as directed by Engineer-incharge.

Providing and laying controlled cement concrete M.200 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (C) Slabs,landing,shelves,Balconies Lintels, Beams, Girders and Cantilever upto floor two level. (more than 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding cost of reinforcement for reinforced concrete work in (C) Slabs, landing, shelves and Cantilever upto floor two level, etc complete as directed by engineer-incharge.

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and reinforcement for reinforced concrete work in (B) Walls, from top of foundation level upto floor two level (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of formwork and excluding the cost of reinforcement for reinforced concrete work in (E) Staircases upto floor two level, etc complete as directed by engineer-incharge.

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level (upto 10 ton)

Providing, Suppying and mixing Dr. Fixit water proofing materials in cemrnt concrete in proportion I.e. 200ml for 50 Kg of 1 cement bag, Or recommended by the manufacturer. It is to be mix in wet concrete.

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in foundation and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in Above plinth level upto floor level two in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (upto 10 ton)

Half brick thick honey- comb brick work with common burnt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. (i) In Cement Mortar 1:4 ( 1- Cement : 4 - coarse sand) (upto 10 ton)

Half brick masonry in common brunt clay building bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:3 ( 1-Cement : 3-coarse sand ) with 2 Nos of 6mm Mild steel round bars after every three course embedded in Cement Mortar inAbove plinth level upto floor level two (B) Conventional (upto 10 ton)

Providing material and labour for 6mm thick CEMENT PLASTER in single Coat For plastering on ceiling and soffits of stairs UPTO FLOOR TWO LEVEL & ABOVE finished even and smooth including curing etc. complete in C:M 1:3 (1 cement :3 fine sand) and finishing with floating coat of neat cement slurry.

Providing material and labour for 12mm thick CEMENT PLASTER in Single Coat For plastering on Brick concrete wall surfaces for plastering UPTO FLOOR TWO LEVEL & ABOVE finished even and smooth including curing etc. complete in C:M 1:3 (1 cement :3 fine sand) and finishing with floating coat of neat cement slurry.

Providing 20mm thick cement plaster in double coat on single or half brick walls for interior plastering upto floor two level & above two level and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) finishing with floating coat of neat cement slurry.

Providing material and labour for fixing polished kota stone slab flooring 20 mm (average) thick base of cemetn mortar 1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror polishing etc. complete (A) 25 mm thick.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on existing flooring by adhesive material including dismentaling of existing flooring and jointed with color cement slurry including finised with flush pointing & cleaning the surface etc, Including cost of material & labour for fixing spacer, epoxy grouting for filling in joints between tiles. complete for antiskit (upto 10 ton)

Providing and laying coloured glazed tiles of the size 300 mm x 200 mm x 8 mm / 300 mm x 450 mm x 8 mm in skirting, risers of steps and dedo on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with white cement slurry.

Providing and laying stone strips having 75 mm to 100 mm thickness for wall cladding on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed with white cement slurry.

Providing and fixing 18 mm thick Granite of any colour and shade gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing and laying chequered precast cement concrete tiles 22mm thick with aggegate of sizes upto 6mm in floors, treads of steps and landings on 20mm thick bed of C.M. 1:6 (1-cement : 6-sand) or L.M. 1:1.5(1-Lime putty : 1.5 coarse sand) joint with neat cement slurry with pigments to match the shade of the tiles. (upto 10 ton)

Providing and fixing tiles roofing with manglore tiles including cement mortar of 1:4 ratio over Sloping RCC slab roof.

Providing and fixing 150mm wide 450mm over all semicircular plain G.I.sheet class-3 gutter with Iron brackets 40mm x 3mm size Bolts, Nuts, washers etc. including making necessary connection with rain water pipes. (i) 0.80 mm thick Sheet. (upto 10 ton)

Providing and fixing 1000mm high stainless steel railing consisting of 50mm dia round SS pipe hand rail supported on 75mm high 25mm x 25mm X 2mm square SS pipe fixed to about 875mm high 38mm x 38mm square SS pipe balustrades placed about 900mm centre to centre. Each balustrade is to be secured by 4 Nos. M8 x 100 fasteners of hilti or any other approved equivalent make and covered with 75mm x 8mm thick base plate with cap. Stainless steel to be Minimum 16 gauge of SS 304 grade complete in all respects as approved by Architect/ Engineer-in-charge.

Distempeing (Two coats) with oil bound distemper of approved brand and manufacture and of required shade on wall surfaces to give an even shade, over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth.

Finishing wall with water proofing cement paint of on wall surfaces (Two coats) to give an approved brand and manufacture and of required shape even shade after thoroughly brushing the surface to remove all dirt and remains of loose powered materials.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing material and labour for fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws, with Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS :2046 Type S, including cost of adhesive of approved quality 1.0mm Thick on both face, with Providing and fixing S.S. tower bolts (barrel type) with necessary screws etc 200mm long x10mm dia, with Providing and fixing S.S. Door Aldrop with necessary screws etc. 300mm long x16mm dia, Providing and fixing S.S. Door Aldrop with necessary screws etc 250mm long x16mm dia, with Providing and fixing S.S. Pipe Handle for door 30cm size on both side of Door shutter, with Providing and fixing S.S hanging type floor door stopper with necessary screws, etc. complete as directed by Engineer in charge. All S.S Shall be ASIS 304 Grade.

Providing and fixing 35 mm thick shutters for Doors, windows and clerestory windows including Indian teak wood frames 12 cm x 7 cm. size including anodized alluminium fixtures and fastenings including primer coat of approved quality and two coats of oil painting etc, complete. (iii) Partly panelled and partly glazed.

Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S. flats at required spacings and frame alround, square or round bars with round headed bolts and nuts or by screws. (B) PLAIN GRILL (upto 10 ton)

Providing and fixing Fly proof galvanised M.S. wire gauge of I.S.l gauge designation 85 G. with wire of dia.0.56 mm to windows and celevating windows including 60 x 20mm beading of teak wood. (upto 10 ton)

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying a priming coat of read lead paint. (A)In beams and joists, channels angles Tees, flats, with connecting plates or angle cleats as in main and cross beams. Hip and jack rafters, purlins conneted to common rafters and the like (upto 10 ton)

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint, brushing, interior to give an even shade including cleaning the surface an even shade including cleanicn the surface of all dirt, dust and other foreign matter.

Providing upto floor two level precast cement concrete jali or grill 1:2:4 mix (1- Cement : 2- coarse sand : 4-graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia. Mild steel wire including roughening,cleaning, fixing and finishing in cement mortar 1:3 and curing complete. (D) 75mm thick

Providing material and labour for construction of Kitchen Platform made from Black Granite (16mm to 18mm thick) in top of kitchen platform rested on black kadapa stone (av.30mm thick) supported on sandwiched vertical supports of Kadapa Stone bottom of granite stone for base of platform, at required distance or as directed by Engineer-in-charge. One side vertical granite stone in geometrical shape, front granite stone patti for fascia work as well as horizontal boarders including molding and mirror polishing by hand grinder to all exposed black granite edges and providing opening of required size and shape of kitchen sink in granite and kadapa stone in line and level. The vertical supports of kadapa stone sandwiched/ gap fill up with cement mortar 1:1 and cement slurry and the granite stone vertical side and patti etc with adhesive material like Araldite etc complete as directed by Engineer-in-charge.

Providing material and labour for making BLACK GRANITE STONE COUNTER WASH BASIN of 0.60mt wide with vertical & Horizontal support of granite stone and having bottom Slab of 25mm to 30mm thick kadappa stone fixing with cement mortar 1:4 ( 1 cement :4 fine sand) and neat cement slurry as per requirement including cutting the granite stone & Providing & fixing oval shape wash basin (Make Jaquar CODE : CNS-WHT-WB02 : Under Counter Basin Size(mm) 195 x 600 x 425) white colour in line & level. All exposed Edges of granite should be moulded including all accessories , flexible inlet pipe 15mm dia, C.P brass waste coupling 32mm, PVC waste pipe 32mm etc. as directed by engineer in charge.

Providing Material, Labour and equipments for Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thickjointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : including Khurra & Gola work With average thickness of 120 mm and minimum thickness at khurra as 65 mm, etc complete as directed by engineer-incharge.

Providing and fixing Six Horizontan lines galvanised steel barbed wire weighting 9.38 Kg. per 100 Metre and One diagonals of and concentina wires respectively, strained and fixed to posts with G.I,staples including fixing the Y shape angle over compound wall etc complete.

Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge compression type fittings, wall clipsetc. including making good the wall ceiling and floor.(G)110 mm -spigot and socket soil, waste and ventilating pipes

Providing and fixing in position cowel went to pipes.(C) 100mm dia

Providing and fixing water closet squatting Pan (Indian type W.C. Pan) size 580mm (Earthwork, bed concrete, foot reste and trap to be measured and paid for separately) (A) Vitreous China.(I) Long pattern = White colour

Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be measured and paid for separately)(A) vitreous China Pattern :(i) in white colour

Providing and fixing 100mm size P or S trap for water closet squatting pan including jointing the trap with the pan and soil pipe in cement Mortar 1:1 (1-Cement : 1-Fine sand)(A) Vitreous China.

Providing and fixing 12.5 Litres high level C..I. flushing cistern with A pair of C.I. or Mild steel brackets, womplete with fittings such as syplionic arrangement, 15mm nominal size brass ball valve with polythene float, lever G.I. China (60 cm. ) and pull union and couplings for connections with inlet, outlet and overflow pipes etc. including cutting holes in walls and making good the same (overflow pipe to be measured and paid fo separately )

Providing and fixing in position with clamps etc. 32mm nominal internal diameter galvanised steel tube flush pipe for high level flushing cistern including connecting the flush pipe with cistern and closet and making good the walls and floors.

Providing and fixing G.I. inlet connection for flush pipe with W.C. Pan

Providing and fixing plastic seat and cover for wash down water closer with C.P. brass hinges and rubber buffers. (B) Black plastic seal and cover.

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including sutting holes and making good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) In white colour.

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white including cutting holes in walls and making good the same but excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x 150mm size

Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mmdia.

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.(A) 100mm dia. Each

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers.

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size.

Providing and fixing 600mm x 120mm glass shelf with C.P. brass bracket and guard rail complete mixed to wooden plug with C.P. brass screws.

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (i) 15mm dia.

Providing and fixing screw down bib taps of following size.(B) Brass chromium plated screws down Bib Tap. (ii) 20mm dia.

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts. (i) 15mm dia.

Providing and fixing brass screw down stop tap.(B) 20mm dia.

Providing and fixing Gun metal check or non-return fullway wheel valve.(B) 20mm dia.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing in pipe line etc. complete.(i) 20mm dia.

Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware 550mm x 300mm.

Providing and fixing Rubber plug for sink or wash basin.

Providing and fixing chromium plated, bottle trap with necessary couplings of approved quality for wash basin.

Providing and fixing ball cock of approved. quality as directed.(A) Copper Metal (i) 25mm dia.

Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having weight not less than 35Kg.

Providing and fixing G.I. Rain water spout of 50mm dia. and 30cm. length.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [B] 20 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [C] 25 mm.

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [D] 32mm.

Providing erecting and fixing double coated Syntex PVC. (ISI) water tank of required capacity each with all necessary fittings and connection etc. complete on terrace.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the following nominal diameter of self cleansing design with C.I scread down or hinged grating including the cost of cutting and making good the walls.

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including testing of pipes and joints complete.(B) 150mm dia. (upto 10 ton)

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(A) 100 mm dia. (112 mm Ave.bed thickness)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P type. (upto 10 ton)

Construction of B.B. Masonary Kundi of clear inside dimension size 0.60M x 0.45M x 0.45M with 23cm thick B.B. masonary wall in C:M 1:6 including required excavation, C.C. 1:5:10 15cms. Thick refilling 12mm thick cement plaster to masonary and floor C.C. layer and fixing the cast R.C.C. manhole cover of size 0.60M x 0.45M With frame and white/ colour wash etc. complete.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or two inlets. (upto 10 ton)

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(i) for 455mm x 610mm size.

Extra over items 24.44 for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(ii) for 500mm x 700mm size.

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. (upto 10 ton)

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(D) 300mm (upto 10 ton)

Drilling of 215mm dia macked bore in loose and alluvial strata and 165mm dia bore in hard and Rocky formation by DTH Rig etc. including cleaning the bore testing of water etc. complete.

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost of rings as per IS specification No.4985/1988 incluidng all local and centra taxes, transportation, freight charges, octroi, ispection charges octroi, inspection charges loading, unloading conveyance to the departmental stores and including cost of jointing materials etc. complete for following dia and ring fit type pipe including lowering, laying and jointing PVC pipes and specials of following class and diameters including cost of labours materials exept cement solvent giving satisfactory hydraulic testing as per ISI cose etc. complete 180mm dia test pressure 6kg/CM2.

Supplying of single phase submersible pump set suitable for 100 mm size or more dia borewell having motor capacity and discharge as under with necessary pannel box (c) Motor rating 2 HP (17 stage) pump having capacity of 106 LPM at 40 mtr head suitable for 25 mm dia. delivery pipe including Supplying and erecting Direct - On - Line Starter with 18 A. rating contatctor and with 3.5 Amp. 18A range directely operated in totally insulated elegant enclosure for single phase operation upto 3 HP as per IS 13947 complete erected on P.W. Block with necessary connection.

Providing and erecting ISI marked PVC insulated PVC Shethed Flat flexible Submercible copper cable approved make of following Size. (b) 3 Core x 2.5 Sq. mm.

Providing material & labour for supplying in standarad length ISI mark high density Polyethylene HDPE pipes suiatable for potable water as per IS Specification no. 4984/1995 including all local and central taxes, transportaion, freight charges, orctroi, inspection charges, loading, unloading, conveyance to the dept. strores etc. comp. rate for HDPE (PE-100) pipe based on the rate of HDPE resin as Rs. 110292.58 (incul. of excise duty @ 12.36% but exclu. of freight and sales tax) Dtd. 1-03-2013. (b) 10.0 kg/cm2, (I) with Excise Duty 50mm dia PVC Pipe.

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as directed.(a) with medium class Rigid PVC pipe and accessories 1.For Point wiring above 10 mtr of length, additional length will be added at rate of mains.

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type electronic fan regulator with separately mounted and accessories with earth continuity of following type erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.(a) with medium class Rigid PVC pipe and accessories

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories.[I] For 6A Plug with 2-1.5 sq.mm Cu. Wire(a) with medium class Rigid PVC pipe and accessories

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories.[III] For 16A Plug with 2-4 sq.mm Cu. Wire(a) with medium class Rigid PVC pipe and accessories

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling with following type accessories

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed.Note:- Maximum up to 6 mtrs length, excess will be considered as Mains for Secondary Point.(a) with medium class Rigid PVC pipe and accessories

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. One No 5 pin plug

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. Blank Plate Single

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge. 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular MCB Switch

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 20 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 25 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in approved manner as directed (a) 32 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 20 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 25 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes. (1) 32 mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 2 wire 1.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 2 wire 2.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 4 wire 6 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size in existing pipe (a) 4 wire 10 sq. mm

Supplying & erecting M.S. Box having 16 Gauge painted with red oxide or Heavy duty PVC box erected flushed on wall or concealed in wall with necessary plastering & finishing as directed of following size.(d) 250 mm x 300 mm x 75 mm(d)

Providing & Erecting 3mm thick Polycarbonate (PC) sheet with grooving as directed

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. b).RG-6

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base frame covered with textured / metallic front plate , modules erected with necessary connection. As desired by Engineer In charge TV Co-axial Socket outlet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 %, CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates )(a) Tube Light With integral/ non-integral driver, 16-18- Watts, Surge - 4KV, IP-20, 4 Feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % , CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) Tube Light With integral/ non-integral driver, 36- Watts, Surge - 4KV, IP-20, 4 Feet

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) LED Lamps Integral type, cool white with PC diffuser Suitable for B22 Lamp Holder, 5-8 Watts.

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB with housing area as a heat sink shall be made of thick sheet steel confirming IS 513/CRCA polyster powder coated and high U V & corrosion resistance with diffuser and/or Polycarbonate optics with company mark/name 120 to 300 V Power Factor more than 0.9 THD < 10% CCT 4000 K to 6500 K Uniformity ratio > 0.7 Luminaire efficiancy > 85 lumens/watt LED driver efficiency > 85 % CREE / OSRAM /PHILIPS Lumiled / NICHIA / SEOUL / BRIDGELUX ( USA ) make LED used for luminaire (Each Fitting required LM-79 & LM-80 Certificates) (a) LED Panel Light with provision for Plane front Frame with translucent cover fixed to housing complete. 12-15 watt, 200 x 200 mm, Surge-4 KV.

Providing and erecting Approved make Ceiling fan with double ball bearing ISI mark with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24/0.2 , 3 core flexible wire with earthing. [Make shall be approved by Engineer in charge]

Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with condenser A.C.230V 50c/s. 1400 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24 / 0.2, 3 core flexible Copper wire with earthing [ Make shall be approved by Engineer in Charge]

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in RCC slab with Making the site as original.

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected concealed in Ceiling with necessary finishing.

Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. Bolt & Nuts erected with necessary hook of 10 mm M.S. Round Bar.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box.

Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square frame ABS body with inbuilt lowers & square frame.

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring mounted low noise operation suitable for medium duty having following dia size and maximum speed in RPM, 305 mm dia 900 RPM

Providing suitable M.S. louver shutter of the Exhaust fan.

Providing recess in wall or window frame suitable for erection of Exhaust fan complete with plastering and colour washing to match the colour of the wall or window complete with expanded metal in order to render the fitting in accessible and the room water-proof.

Providing window frame suitable for erection of Exhaust fan complete covering the remaining portion of window with 15 mm. thick plywood and colour washing to match the colour of the wall.

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Single phase 4 way SS Double door

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Single phase 8 way SS Double door

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) Three phase 6 way SS Double door for single phase outgoing horizontal box

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Single Phase 4 Way

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Single Phase 8 Way

Supplying & erecting Sheet Steel powder coated Cable end termination Box to be mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra wires & Cables, suitable for following size of MCB DB Box. Three Phase 6 Way

The Above all items of MCB, DB the cost of erection on New angle iron frame add following.up to 8 way single phase

The Above all items of MCB, DB the cost of erection on New angle iron frame add following.above single phase 8 way and all three phase DBs.

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 25 Amps.DP

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. for following Max. rating erected as directed 40 Amps.DP

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on 3 phase and neutral 415V. having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component for following Max. rating erected as directed. 40Amps. FP

Miniature circuit breaker single pole 6A to 32A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 6 to 32 Amp.

Providing & erecting 240 V MCB double pole switch for motor & inductive load (C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity 40 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 6 to 32 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 40 Amp.

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity 63 Amp.

Approved make Three Phase & Neutral LT Heavy Duty Switch Disconnector Fuse Unit Cubical type for panel mounting complete with operating mechanism suitable to operate on 415V A.C. , 23A duty With HRC fuses of suitable load confirming to IS. 13947 (Part I & III). of following capacities.100Amp/125 Amp

Cable Terminal ( ‘Plain" Type)Set of Four for 32 / 63 Amps

Cable Terminal ( ‘Plain" Type)Set of Four for 125/200 Amps

Supplying and erecting triple pole & neutral 440V/ 500V panel mounting Aluminium Busbars with four equal Nos. of bus having current density not more than 0.8 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulating tape for phase sequence of following current carrying capacity, erected with necessary bus bar supports /insulators, main cable socket to each busbar,erected in existing cubical panel with necessary connections. Suitable for 200 Amp. Capacity

Supplying and erecting approved make 415V bakelite fuse fittings for front connection / busbar type, to accommodate HRC fuse link, with spin - riveted brass contact, having thermo plastic inflammable material & single piece extruded brass box contact to lock with adequate cable hole to accommodate aluminium conductors suitable for (without HRC fuse) 16 Amp.

Supplying Bolted Connections (BS type) HRC fuse link capable to withstand 80KA confirms to I.S. 13703 for following current capacity up to 32 Amp.

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel board having IP-64 protection made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with necessary supporting angles, flats including cutting, bending, drilling, welding, riveting with internal partitions & cable alley as per requirements & instruction of engineer-in-charge with erection of supplied switch gears, BUSBARS, with suitable size of inter connecting PVC copper wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses for measuring instruments, earth bus & earth bolts, foundation flange - bolts-base Plates, sufficient nos. of hinged doors, handles with locking arrangement and rubber gasket complete. The Panel shall be painted with epoxy powder coating. (The rates excludes the cost of switchgears, bus bars, inter connecting mains & Copper Aluminium strips, meters, Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following approved manufacturers with following size.(A) The standard companies switch gear shall be used and only manufacturers at CPRI approved factory and shall be certified by that company whose switch gears are used after fabrication for beneficial use with 350mm depth

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using proper clamp.

Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG erected & connected as directed (For panel)

For using salt and charcoal / coke as required for pipe type earthing.

Add Extra for excavation in Hard rock by dry and wet blasting and chiselling for pipe type earthing.

Supplying and erecting LED Street Light/Flood light fittings with High power White LED's wattage of 1 watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminium housing with smooth finish powder coated and heatsink extruded aluminium with diffuser and Polycarbonate optics/lenses with company mark/name engraved or embossed 120 to 300 V, Power Factor more than 0.95, THD less Than 10% CCT 5000 K to 5700 K, Uniformality ratio >0.45, Luminaire efficiancy > 85 lumen/watt, LED driver efficiancy > 85 %. CREE/OSRAM/PHILIPS Lumileds/NICHIA/SEOUL/Bridge Lux ( U.S.A.) make LED used for luminaire. ( Each fittings required LM-79 & LM-80 Certificates) Flood Light (IP-65), Surge- 4 KV Above 70 watts to 90 watts

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

Making trench in Hard Murrum / Tar Road of suitable width of 90 cms or required depth for laying any size of cable or locating the fault all over the run and back filling the same and making the surface as normal ground.

(B) If additional machineries like hammer driller or JCB use [Add]

Covering of cable with second class bricks or cement tiles laid cover the cable crosswise & also on both sides with covering of 7. 5 Cms. layer of sand above & below cable (16 bricks per meter)

Providing and erecting iron clad cable route marker duly marked with ELE.CABLE of size 23 cms.X 12 cms. Flushed with ground in cement foundation as directed by Engineer in charge.

Supplying following size of Light duty “A” Class G.I . Pipe & erecting as directed by Engineer-in-charge. 50 mm dia

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. 2 to 4 core 10 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. 3 & 1/2 core 70 Sq. mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 1.5/ 2.5/4/6 Sq.mm

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 70 Sq.mm.

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. 35/50 Sq.mm.

Providing and erecting 18 G. M.S. termination box outdoor type suitable for- 1.1 KV PVC insulated armoured cable complete erected with clamp, bolts, nuts etc. suitable of following size of cables.3 core 70 / 95 Sq. mm

Providing and erecting Epoxy Outdoor / Indoor end termination Kit suitable for LT PVC insulated armoured cable1.1 KV grade complete with ferrule bushing and accessories and suitable clamps duly erected and connected to the supply for all cores cables of following size. 2.5 to 16 Sq. mm

Providing and erecting Epoxy Outdoor / Indoor end termination Kit suitable for LT PVC insulated armoured cable1.1 KV grade complete with ferrule bushing and accessories and suitable clamps duly erected and connected to the supply for all cores cables of following size. 70 to 120 Sq. mm

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame, prefilter housing with 'O' ring presediment filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40 Osg inline type post carbon filter auto low & high pressure switches with following size of storage tank & LPH capacity & erected as directed with one year comprehensive maintenance guarantee. [B] 25 Ltr / Hr with 30 Ltr. S.S. Pressure Tank

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 45°C. The outlet temp. of the water should drop by 15°C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating, coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.

Conveyance charges including loading / unloading for Water Cooler from store to site (ii) Outside Divisional Head Quarter for first 60 Km from store.

Supplying & erecting Galvanized iron pipe post “B” class 88.9 mm O.D 6 mtr. Long duly painted with two coats of aluminium paint complete with metallic base- plate of 300 mm x 300 mm x 4mm thick for using as a compound light pole with approx. weight 47 Kg.

Providing M-20 / 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of size 45 x 45 x 100 cms. Deep in below ground level with plinth of 45 cms x 45 cms (or 45 cms dia x 45 cms) high upper ground level with necessary curing and finishing in approved manner. ( for 4 & 6 mtr pole)

Fabricating terminal box for street light pole made from 16 SWG M.S. sheet having following size complete with fixing arrangement for terminal board, with necessary hole for wire entry and exit from the box. The box shall be provided with cover and hinges on one side and bolting at other end The box shall be fixed by clamps fabricated from 25mm x 6mm flat.The box shall be painted with one coat of red oxide and two coats of paint having following box size. 330 mm x 260 mm x 140 mm (depth)

Providing street light pole bracket comprising main Light Class MS tube of 4.2 cms. outside dia. complete with suitable M.S. sleeve tubing of approx. 45cms.length and suitable for 76.5mm. /80 mm or require size pole top having sufficient fastners for fixing the brackets and having suitable rise as per site condition as directed and spread of 2 mtr.with suitable welded stiffener reducer and with lock nut complete painted with one coat of Red oxide / PU base primer and two coats of Aluminium / PU paint. Suitable for side entry fitting brackets of following nos of arms.Single Arm bracket 2 Mtr

Supplying and erecting LED Street Light/Flood light fittings with High power White LED's wattage of 1 watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminium housing with smooth finish powder coated and heatsink extruded aluminium with diffuser and Polycarbonate optics/lenses with company mark/name engraved or embossed 120 to 300 V, Power Factor more than 0.95, THD less Than 10% CCT 5000 K to 5700 K, Uniformality ratio >0.45, Luminaire efficiancy > 85 lumen/watt, LED driver efficiancy > 85 %. CREE/OSRAM/PHILIPS Lumileds/NICHIA/SEOUL/Bridge Lux ( U.S.A.) make LED used for luminaire. ( Each fittings required LM-79 & LM-80 Certificates) Street Light (IP-65), Surge- 4 KV Above 48 watts to 60 watts Cat III

SCHEDULE A-1 ( Reference NIT Page No.53)

Providing material labours, machinery & equipment for Demolition/dismantling of old buildings on ground floor, including foundation, Plinth, Wall, column, beams, slabs, doors, windows, MS grills, Angles, Galvalumn sheets & A.C. sheets roof including disposal of all materials, building rubbish/malba/unserviceble, diemantled or waste materials, earth work by mechanical means, including loading, unloading, transporting the materials with all lead and lift etc. complete and cleaning the site as directed by Engineer in charge.

M/s Yogesh Construction Co

Unique builders

D.B.Infratech

Bidder Name

P.R. Patel and Co.