Development of City Centre at Kavaratti Island, Lakshadweep

Amount

Excavation for work

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.(Hard rock (requiring blasting))

Plain Cement Concrete

Provdiing and laying Plain cement concrete in open foundation including form work shuttering etc. complete as per drawing and technical specifications and as per relevant clauses of sections 1500, 1700 & 2100 with. (P.C.C. M-20)

Ready mixed Cement Concrete

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. (All works above plinth and upto floor V level) (Concrete of M35 grade with minimum cement content of 300 kg /cum)

Plaster

20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

TMT Fe 500 Epoxy coated

TMT Fe 500 Epoxy coated or Zinc silicated (or equvivalent compound) Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete and also as directed by engineer incharge.

AAC Block Masonary Work

Providing and laying AAC Block masonary 125mm thick with grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (part 3) in super structure above plinth level in cement mortar 1:4 (1 cement: 4 coarse sand)

Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) : With Modular Bricks

MS Tube Pipe

Steel work in built up tubular (round, square or rectangular hollow tube) trusses etc. including cutting, hoisting, fixing in position & applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Elevation Grill

Providing & Fixing Elevation Grill Jali with necessary coatings & fittings as directed by Engineer-in-charge.

MS Section

Providing & Fixing MS section as directed by Engineer-in-charge

MS Sliding Gate

Supplying & Fixing Gate & its accessories as per the requirement & direction of Engineer-in-charge.

MS Cladding on roof

Supplying & Fixing MS Roof Cladding as per the direction of Engineer-in-charge.

Wooden Carving Aluminium composite panel Cladding

Designing, fabricating, testing, installing and fixing in position curtain wall with Aluminium composite panel cladding (Wooden Finish) with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc.

Wooden Roofing Sheet

Providing & Fixing Wooden Roofing Sheet of cedar type wood having thickness of 10 mm with coating as directed by Engineer-in-charge.

ACP Roofing Sheet

Providing & Fixing ACP Roofing sheet having thickness of 10 mm with Exterior face coil coated with PVDF and Interior face coil coated with polyester as directed by Engineer-in-charge

Glass Door

Providing & fixing 12 mm thick frameless toughened glass door shutter of approved brand & manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge.

Aluminium Glass Cladding

Providing and fixing glazing in aluminium partitions/claddding with EPDM rubber/neoprene gasket etc. complete as per the direction of Engineer-in-charge. (With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm))

MS Roofing Sheet

Providing & Fixing MS Roofing top sheet having thickness of 0.5 mm as directed by Engineer-in-charge

Cement Concrete Terrazo tiles

Providing and laying Cement Concrete Terrazo tiles or others in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. as per direction of Engineer-in-charge.

etchblasted tiles

Providing and laying etchblasted tiles or others in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. as per direction of Engineer-in-charge.

Antiskid floor tiles

Providing and laying Antiskid floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. as per direction of Engineer-in-charge.

Clading Tiles

Providing and fixing dry cladding upto 10 metre height with 30 mm thick gang saw cut stone with machine cut edges of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (White sand stone - 30 mm thick gang saw cut stone)

Passenger Lift

Supplying and Installation of Passenger Lift as a complete job as per instructions of Engineer-in-charge.

Passenger Lift for Panchayat and multipurpose Building

Supplying and Installation of Passenger Lift as a complete job as per instructions of Engineer-in-charge.

Paver block

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

Pink marble

Providing & fixing Pink marble slab (plain 18 mm thick) as per direction of Engineer-in-charge.

Granite stone tiles

Providing & fixing 8 mm thick granite stone tiles (mirror polished of all shades) as per direction of Engineer-in-charge.

Sand bed

Providing & fixing Sand Bed (40 mm thick) for Interlocking Block as per direction of Engineer-in-charge.

Mortar bed

Providing & fixing Mortar Bed (50 mm thick) for Interlocking Block as per direction of Engineer-in-charge.

Painting

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm as per direction of Engineer-in-charge.

Ceiling Light

Supply, Installation, Testing and Commissioning of smart led panel lights in ceiling as required. as per direction of Engineer-in-charge.

Step light

Providing & fixing step light with required fixing accessories as a complete job as per engineer in charge.

Walk over LED

Providing & fixing Walk over LED with required fixing accessories as a complete job as per engineer in charge.

Street light pole

Providing & fixing Street light pole with required fixing accessories as a complete job as per engineer in charge.

Exhaust fan

Supply & Installation of exhaust fan as per instructions of Engineer-in-charge.

ceiling fan

Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. as per direction of Engineer-in-charge.

Centralised air

Supply & Installation of centralised air conditioner of 2 ton. as per direction of Engineer-in-charge.

split air conditioner

Supply & Installation of centralised air conditioner of 2 ton. as per direction of Engineer-in-charge.

Electrical wirings

Supplying & fixing necessary electrical wirings, switch board & other miscellaneous items as per the requirement & direction of Engineer-in-charge.

Furniture for Security Cabin

Supplying & Installation of required furnitures & its accessories as per the requirement & direction of Engineer-in-charge.

Water Closet

White vitreous china dual purpose closeet (European W. C.) of any brand suitable for use as squatting pan or european type water closet as per manufacturer's specifications. as per direction of Engineer-in-charge.

Flushing Cistern

Floor Mounted white vitreous china double trap syphonic WC with 10 litre cistern and all fittings & fixtures, seat cover. as per direction of Engineer-in-charge.

Wash basin

Providing & fixing Wash basin with necessary fittings as per instructions of Engineer-in-charge.

Kitchen wash sink

Supplying & fixing of Kitchen wash sink with all necessary accessories as directed by Engineer-in-charge.

Urinals

Providing & fixing Urinals with necessary fittings as per instructions of Engineer-in-charge.

PVC Overhead tank

Providing & fixing double layer PVC Overhead tank of capacity 3000 lts as per instructions of Engineer-in-charge.

Fire safety

Supplying & Installation of necessary fire safety equipments & accessories as per direection of Engineer-in-charge.

HDPE rainwater Pipe

Supplying & fixing HDPE rainwater down pipe of 100 mm & 75 mm with its all accessories as per the requirement & direction of Engineer-in-charge.

Gas pipe line

Supplying & fixing of Domestic gas pipe line with all necessary accessories as directed by Engineer-in-charge.

Rain Water Panali

Supplying & fixing PVC Panali with its all accessories as per the requirement & direction of Engineer-in-charge.

HDPE rainwater Pipe for Food Zone+washroom

Supplying & fixing HDPE rainwater down pipe with 100 mm & 75 mm its all accessories as per the requirement & direction of Engineer-in-charge.

Sitting Benches

Providing and fixing wooden Sitting Benches as per instruction of Engineer-in-charge.

Furniture Accessories

Supplying & fixing of necessary wooden partition & its accessories and also other miscellaneous items as per direction of Engineer-in-charge.

shower panel & its accessories

Supplying & fixing of necessary shower panel & its accessories and also other miscellaneous items as per direction of Engineer-in-charge.

Elevation glazing glass

Providing & Fixing Elevation glazing glass as sirected by Engineer-in-charge.

coffee shop

Providing & Fixing coffee shop as directed by Engineer-in-charge

Internet surfing Zone

Providing & Fixing Internet surfing zone as directed by Engineer-in-charge

Indoor Games as per direction of Engineer-in-charge.

Billards Table(2.84m x1.42m)

Fooseball (1.40m x 0.80m)

Table Tennis Table (2.74m x 1.52m)

Other Indoor Games (Carrom, chess)

VR Car Gaming

car gaming having simulated driving system along with racing seat and touch screen control. With 1 year warrenty

VR Arcade Game

car gaming having multi-axis synchronised motion system along with its headset and touch screen control. With 1 year warrenty

Racing Simulator

car gaming having simulated driving system along with racing seat and touch screen control. With 1 year warrenty

Fish Spa

Providing & Fixing Fish Spa Setup as per instructions of Engineer-in-charge.

Massage Chair

Providing & Fixing Massage Chair as per instructions of Engineer-in-charge.

EPDM flooring

Providing and fixing EPDM flooring as per instructions of Engineer-in-charge

Kid's play equipments

(a) Bridge Ladder Climber Park Play Equipment

(b) Fibreglass Dinosaur Slide

Bollard type

Providing fixing installing bollard type garden light with required fixing accessories as a complete job as per engineer in charge.

Tree plantation

Landscapping tree plantation of varied types as per instruction of Engineer-in-charge.

Solar trees

Providing and fixing Solar trees as per instruction of Engineer-in-charge.

RO Drinking Water

Providing & Fixing marble RO Drinking Water dispenser as per instruction of Engineer-in-charge.

Underground Sump (1 LL) as per instruction of Engineer-in-charge.

Earth filling

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 and for all lift. as per instruction of Engineer-in-charge.

Plaster

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) as per instruction of Engineer-in-charge.

Sanitory & its accessories

Supplying & fixing of necessary sanitory & its accessories and also other miscellaneous items as per direction of Engineer-in-charge.

UPVC 75 mm

UPVC 50 mm

T-pipe

Elbow-Pipe

Coupler

Misc. Item

Sludge pipe

UPVC 32 mm

UPVC 20 mm

UPVC 25 mm

UPVC 15 mm

Granite Premium

Granite and Marble 25mm / 32mm thick premium grade with approved colour design and pattern.

Central Fountain

Providing and fixing Cental fountain in central circle as per instruction of Engineer-in-charge.

Watch Tower

Providing and fixing Viewing Tower, including R.C.C. Foundation,Column,Slab, Stair and finishing items with premium qualitty Flooring and Glass work as per instruction of Engineer-in-charge.

Mahatma Gandhi Statue

Providing and fixing Mahatma Gandhi Statue in central circle as per instruction of Engineer-in-charge.

Sub-grade

Construction of Subgrade/Embankment and earthen shoulders with approved material obtained from Borrow pits with spreading, grading to required slope and compacted to meet requirement of table No. 300-2 ( Subgrade CBR ≥ 11 ) as per instruction of Engineer-in-charge.

Sub-base

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401. (As per Code No. 4.1 NH SOR-2023-24) as per instruction of Engineer-in-charge.

Construction of Dry Lean Cement Concrete Sub-base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing. as per instruction of Engineer-in-charge.

Concrete pavement

Construction of reinforced, dowel jointed, plain cement concrete of M35, pavement over a prepared sub base with Ordinary Portland Cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing. as per instruction of Engineer-in-charge.

Charging Station

Supply & Installation of charging station as per direction of Engineer-in-charge.

Water Pipeline

Supply & Installation of Water Pipeline as per direction of Engineer-in-charge.

Furniture for Scanning Center

Supplying & Installation of required furnitures & its accessories as per the requirement & direction of Engineer-in-charge.

SMARD (BID ID -10434)

Anand Buildtech Private Limited (BID ID -10400)