SPECIAL REPAIR TO EXISTING TOILETS AT HRDC BLDG PROVN OF ALUMINIUM WINDOWS AND GUARD BARS GRILLS AT GROUP HEAD QUARTER BUILDING OF BEG AND CENTRE AND ADDITION ALTERATION OF TECHNICAL LABS AND TEA ROOM OF ADM BLOCK AT DUNKRIK LINE UNDER GE C KHADKI

Amount

Taking down chowkhats or frameswith shutter (without taking off shutter from the frames) & removing from site exc. 1.5 Sqm but n. exc. 4 Sqm each etc complete all as specified and as directed.

Description all as item No 01 above but n.exc. 1.50 sqm each

Material and labour for Casement Windows with profile finish in RAL powder coating , wood grain finish, anodisation with outer frame width 40.00mm and vent shutter 49mm, window door shutter width 78.40mm with T-profile using glazing bead height 21.0mm Using Aluminium Alloy 6063-T4/T5/T6 complete all as specified and as directed. NOTE :- (a) windloads are considered as per IS 875-III (b) The size of window should be considered asdirected.

Material and labour for Pleated Fly mesh for Casement Windows of PVL-22 HEAVY DUTY series in any type of window opening (wheather one side or both side operational complete all as specified and as directed. Note:- (a) The size of window should be considered as directed.

Material and labour for Framed work such as grills etc with ends of bar shouldered or revetted or forged into spikes framed guard bars including framed flat iron of any size and section to combined the windows complete all as specified and as directed.

Material and labour preparation of new steel surfaces of any desciption over 10 cm in width or girth not other wise descibed and applying two coats of synthetic enamell paint over a coat of red oxide complete all as specified and as directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown on Page No. 160 of SSR 2010 part II. complete all as specified and as directed.

Supply and fix 30mm thick FACTORY MADE MOULDED DOOR SHUTTER ‐ WOOD FREE consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 25mm x 25mm for stiles, top and bottom rails. M. S. frame shall have a coat of steel primers. The inner panel shall consist of 25mm thick EPS of Density 23 Kg /Cbm. bonded with 2mm thick termite proof, water proof and fire resistant moulded PVC Sheet Manufactured by an ISO‐9001‐2015 certified company, with 2, 4, 6 raised panel design in different plain and / or prelam colours after routing the Moulded design on one side & 2mm plain and /or prelam PVC sheet on other side of the EPS. The edge of panel to be sealed with lipping of 15mm wide PVC sheet baton ( made by sticking 2mm rigid foam PVC sheets of 5mm (±0.25) thickness using PVC solvent cement ) and stile sides 25mm (5mm x 5nos.) thick and 30mm width PVC Sheet fitted along M.S. tube for hardware provision & for lock 25mm thick ( 5mmx5nos. ) PVC sheet of size 150mm x 200mm fixed with inner side of EPS Panel etc. complete all as per specification & as directed .

Supply and fix for powder coated anodised aluminium ventilator shutters, fixed type without sash bar including stainless steel wire cloth of 0.63 mm nominal dia and average aperature 1.4 mm, glass for louvered portion, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc.and fixed to stone masonry wall including demolition of RCC jali ventilators complete all as specified and as directed.

Supply and fix Flush shutter solid core 30 mm thick with brick board core & ply wood face panels commercial type on both sides complete all as specified and as directed.

Supply and fix for pressed steel door frames of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B1 in door frame filling complete all as specified and as directed.

Supply and fix in repairs Butt Hinges medium weight cold rolled stainless steel 100 mm long complete all as specified and as directed.

Supply and fix for Extruded aluminium alloy handles 150 mm, fabricated type, anodised complete all as specified and as directed.

Supply and fix for mild steel sliding door bolts, plate type, with stainless steel bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed 300mm long

Aluminium anodised barrel tower bolt 200mm long complete all as specified and as directed.

Supply and installation of Toughened Glass Swing Door, complete with hardware and accessories.1. Door Type: Type: Single Leaf Swing Door Operation: Manual swing (inward/outward as per site requirement) Mounting: Floor-mounted / wall-mounted hinges (as per site requirement) 2. Glass Specification: Material: Toughened (Tempered) Safety Glass, Thickness: 10 mm, Finish: Frosted Glass, Edges: Polished edges, Size: As per site resquirement 3. AccessorieSupply and fixittings: All fittings shall be ISI-marked or equivalent approved brand a) Top & Bottom Patch Fittings: SS 304 Grade, Satin/Glossy finish, Corrosion-resistant, Brand-approved patch fitting kits b) Floor Spring : Heavy-duty hydraulic floor spring c) Top Pivot: Stainless steel, Adjustable pivot pin d) Bottom Pivot / Floor Plate: Stainless steel, Flush floor-mounted e) Handle: D-type / H-type pull handle Stainless steel, Length: 600 mm (or as specified), Mounted on both sides of the door

Contd from.,,.....17.00 f) Locking Mechanism: Side lock with strike plate g) Rubber Gaskets and Silicon Sealants: i) Signage: "Push / Pull" signs in etched vinyl or stainless steel The door shall be aligned correctly for smooth and noise-free operation. Necessary holes/cut-outs in glass must be factory-made. All accessories must be securely fixed to prevent vibration and loosening over time. NOTE :- Payment shall be made on per square meter (sqm) basis, including all hardware, fittings, and installation.

Supply and fix for powder coated aluminium sliding windows having three Nos of tracks including one guazed shutter for mosquito proofing including stainless steel wire cloth of 0.63 mm nominal dia and average aperature 1.4 mm and two Nos of glazed shutters including 4mm thick coloured glass and aluminium section weight not less than 0.55 Kg/RM for shutter and not less than 2.3 Kg/RM for frame including necessary cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, suitable handles, locking arrangement and fixed to stone masonry wall complete all as specified and directed .

Supply and fix for vitreous china Flat Back Large urinal size 37.5x39x59 cm, starwhite pastel special, including and providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinals to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; including flush valve fixing with brackets, flushing pipe, grating and union for discharge pipe complete all as specified and directed. MAKE :- Hindware cat no 60002 Make for Flush valve :- Hindware

Taking up or down steel tubing 15mm dia and connections including cleaning for refixing or removal to store all as specified and as directed.

Taking up or down steel tubing 20mm dia and connections including cleaning for refixing or removal to store all as specified and as directed.

Supply and fix tubes 15mm bore medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified and as directed.

Supply and fix tubes 20 mm bore medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specified.

Supply and fix 75mm bore PVC(SWR) pipe, type 'B' single socketed in any length with rubber ring joints laid in trenches or floors fixed in repairs all as specified and as directed.

Supply and fix 110 mm bore PVC (SWR) pipes, type 'B' single socketed in any length with rubber ring joints laid in trences or fixed to wall including PVC clamps and necessary fittings fixed in repairs complete all as specified and as directed.

Supply and fix PVC (SWR) bends type 'B' of any radius, 75 mm dia complete all as specified and directed.

Supply and fix PVC (SWR) bends type 'B' of any radius, 110 mm dia complete all as specified and directed.

Supply and fix 75 mm bore PVC (SWR) branch piece (single Y), type 'B' equal or unequal with access door complete all as specified and as directed.

Supply and fix 110 mm bore PVC (SWR) branch piece (single Y), type 'B' equal or unequal with access door complete all as specified and as directed.

Supply and fix PVC (SWR) gully trap 125/110mm setting and jointing in solvent cement complete all as specified and as directed.

Supply and fix 75 mm bore PVC Floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

Supply and fix of EWC of size 62.5x36x76 cm of one piece, including trap, flush tank, seat cover & other necessary items, fixed in repairs, complete all as specified and as directed. MAKE :- Hindware, Cat part no. 92535 (P-18.5) Cist:92130

Supply and fix Swan Neck Tap with left hand operating Knob, cast copper alloy fancy type, chromium plated, screwed down high pressure, with all other fittings complete all as specified and as directed. MAKE :- Hindware Cat no F280012

Supply and fix Health faucet, Hand Shower, with 1mtr Long easy flex tube in chrome finish & wall hook complete all as specified and as directed. MAKE :- HINDWARE

Supply and fix Towel shelf assembly consisting of chromium plated bracket guard and with CP aluminium railing complete all as directed by Engr-in- charge. MAKE :- Hindware Cat no F870009

Supply and fix Towel ring, brass body, glossy finish complete all as per of Hindware or equivalent make as specified in PS all as specified and directed, Chromium plated towel ring all as specified and directed. MAKE :- Hindware Cat no F880007

Supply and fix Table top wash basin, rectangular shape of size 45x11x49 cm of star white colour complete all as specified and as directed. MAKE :- Hindware cat part no 9110010SW

Supply and fix in repair angle cock cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule for 15 mm bpre of pipe complete all as specified and as directed.

Supply and fix in repair two way angle cock with flange cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down , screwed both end for iron pipe or or brass ferrule for 15 mm bore of pipe complete all as specified and as directed.

Supply and fix Bib taps 15mm dia, cast copper alloy chromium plated, with CP flange makes specified in PS fixed in repairs complete all as specified and as directed.

Supply and fix in repairs Stop valve fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle, 15mm bore size screwed both ends for iron pipe or for unions and fittings all as per makes specified in PS complete all as specified and as directed.

Cutting chases, pinning & making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in stone/ concrete block walls complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp insulation, Ac etc), any thickness including cover fillets complete all as specified and as directed.

Supply and fix interlocking aluminium alloy anodised snap grid consists of main Tee runners of size 38mm x25mm x1.5mm spaced 1200mm centre to centre and cross Tee of size 25mmx25mmx 1.5mm, 1200mm long spaced between the main Tee at 600mm centre to centre to form a grid of 1200mmx600mm and provide a secondary cross tee 25mm x1.4mm ( of length 600mm) to be interlocked of the centre of 1200mmx600mm panel to form a grid of 605mmx605mm and wall angle 25mmx25mmx 2mm. Aluminium alloy extruded section shall be aluminium anodised (minimum 15 micron ) and shall conform to IS 733, IS 1285 and IS 737. including Hangers of GI wire 6mm dia to be fixed by approved rawl plug, level and justers and screws etc complete all as specified and as directed.

Material and labour for 8-9 mm thick Gypsum board/tiles for insulation and accoustic purposes, 60cmx60cm in size , fixed with nails to timber frame work or with staples on snap grid in ceiling complete all as specified and as directed.

Demolition of stone slabs/flooring of any description laid bedded and pointed any mortar complete all as specified and as directed.

Material and labour for Granite slab in floor/door & window cill /urinal partion machine cut for 20 mm thick bedded and jointed with colour cement to match cut to shape required including jamb and cill of window / partion /slab complete all as specified and as directed.

Material and labour for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including Material and labour for screed bed or bedding layer 15 mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and as directed.

Description all as item No.49 but on step riser skirting over and including 10mm thick rendering in CM (1:4) complete all as specified and as directed.

Providing and fixing toughened glass fixed partition in washroom made from 10 mm thick frosted toughened safety glass of approved make, conforming to IS 2553 (Part 1):2018 or equivalent international standards. Specifications: 1. Glass Material: Type: 10 mm thick frosted or acid-etched toughened glass. Edges: All edges shall be machine polished to smoothness for safety and a clean aesthetic. Finish: Frosted/matte finish for visual privacy or clear finish with privacy film as specified. 2. Fixing System: Glass shall be fixed using stainless steel (SS 304) or anodised aluminium U-channels, brackets, or wall clamps. Mounting: Fixed to floor, wall, or ceiling using SS angle brackets or patch fittings with rubber padding to protect glass edges. Gaskets & Sealants: Use EPDM rubber gaskets or spacers and neutral cure silicone sealant at joints Contd to 51.01

Contd from.,,.....51.00 3. Accessories: SS 304 grade fittings and fasteners, including: U-channel sections, Glass clamps or patch brackets, Anchor bolts and screws with SS cover caps, Rubber/neoprene spacers and buffers Optional: End caps, base seals, stabilizer bars (if height >1800 mm), or wall stiffeners. 4. Height and Dimensions: Standard panel height: 1200–2100 mm depending on location 5. Additional Features (As Required): Etched or vinyl safety banding at eye level for visual marking Anti-fungal silicone for wet areas, Stainless steel foot brackets for bottom clearance installations. NOTE :- Clean all glass surfaces after installation, Payment shall be made on the basis of actual installed area in square meters (Sq.m), including all fittings and accessories.

Material and labour for precast cement concrete block massonry with solid blocks exceeding 10 cms in width built in cement mortar 1:6 precast cement concrete (1:3:6) type C1 using 20mm graded stone aggregate complete all as specified and as directed.

Material and labour for rendering 10 mm thick on fair faces brick work /PCC block masonary or concrete surface of wall using cement plaster 1:6 and finished even and smooth (without using extra cement) complete all as specified and as directed.

Material and labour preparation of newly plastered surface and applying two coat of oil bound Distemper over a coat of primer on wall etc complete all as specified and directed.

Supply and fix rotational moulded polyethylene water storage tanks 1000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position with embossment of ISI mark including dismantling and removing of old tank all as specified and directed.

Material and labour for preparing plastered or unplastered old surfaces of wall including brooming down or scrap down with steel wire brushes, smoke soot, moulds, moss efflorescent salts and trading oil and greasy spot and applying two coat of oil bound distemper complete all as specified and as directed.

Material and labour for two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces including all necessary preparation over 10 cms width or girth complete all as specified and as directed.

Material and labour for WPT to sunken floor treatment with following specification :- (a) Clean the sunken portion of toilet / Baths/ WCs/ Kitchen thoroughly to remove laitance, dirt, dust etc. (b) Form angle fillet of size 40 mm x 40 mm along the junction of wall and floor using polymer modified mortar (“ Dr fixit” Pidicrete URP” or eqvt). (c) Sanitary pipes entering through walls and floor shall be sealed with “Dr Fixit Bath seal Tape” and the gaps to be grouted with non-shrink cementitous grout “Dr Fixit Bath seal Grout” or eqvt. Nahani traps etc to be fitted securely and the gaps around it to be grounted in the same manner. (d) Apply one coat of a Bitumen-modified polymer coating “Dr Fixit Bath seal Plus” or eqvt on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely. Contd to 58.01

Contd from.,,.....58.00 (e) In the remaining area, in dry substrate condition brush apply first coat of the same coating and further apply second coat when first is dry. Extend the coating upto 150mm above the FFL. Above FFL, another cementitious waterproofing waterproof coating “Dr Fixit Pidifin 2 K” or eqvt can be further applied right upto 2.1 m to waterproof the shower area also, if it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6-8 hours and allow to dry completely. (f) After 2 to 3 days, sunken portion must be overlaid with a 50 mm thick concrete screed 1:3:6 type B0 mixed with integral WPC (Liquid) laid to slope 1:60 towards outer face of wall. Provide 40 mm OD UPVC pipe at the lowest point with 300 mm projection beyond the outer face of the wall. Then fill up the sunken portion with lean concrete 1:5:10 type E2. (g) After completing plumbing work in the toilet/WC/Bath/Kitchen floor, tiling work (floor and dado) can be carried out using suitable Tile Adhesives and ready to make tile grouts of approved makes such as Dr Fixit, FOSROC SIKA, MC BUCHEMIE, ROFF, etc.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles in store rubbish of the premises complete all as specified and as directed.

Material and labour for non skid ceramic coloured tiles , 7 to 8 mm thick (square or rectangular) area of each tile exe 0.18 Sqm but n.exe 0.38 Sqm, laid in floors set and jointed with neat cement slurry including pointing in white cement with pigment to match the shade of tiles and 15mm thick screed bed in cement mortar (1:6), complete all as specified and as directed.

Material and labour for Glazed ceramic coloured tiles in vertical surface 300x600 of 7 to 8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick cement plaster (1:4) as backing coat complete all as specified and as directed.

Material and labour for Glazed ceramic coloured tiles in vertical surface 600x1200 of 7 to 8 mm thick set and jointed in 3-6 mm ( 5mm average) thick bed of adhesive mortar of Polymer modified cementitious adhesive ( Bal Endura gold star / letecrete / Rock force ) in conjuction with polymer modified liquid Bal Endura admix Adlor equivalent product of letercrete / Rock force mixed in required porportion as specified by manufacturer including filling / scaling of joints 2-3 mm thick between the tiles with epoxy grout of Bal Endura Epoxy grout / Letecrete / Rock force with matching colour pigment to make it water tight and finished neat complete all as specified and as directed.

Material and labour for 25 mm thick Cement concrete in level course for receiving floor tiles using Type B1,1:2:4 (20 mm graded aggregate) complete all as specified and as directed.

Material and labour for Core cutting, using Core cutting machine inside Block/Stone/Brick Masonary wall of size more than 75 mm but less than 150 mm in dia for any type of pipe or trap installation through holes, and hole to be filled with PCC 1:2:4 after installation of pipe or trap, including making good existing disturbed portion in CM 1:3 in any type of masonary wall/slab complete all as specified and as directed.

Supply and fixing powder coated aluminium door made out of hollow extruded aluminium section as mentioned below: Each door having 02 Nos disc or D type handels, 02 Nos aluminium tower bolts 200 mm size one aluminium sliding door bolt or 250mm size, one brass mortice lock of six levers with key in duplicate regulated by double action hydraulic floor door spring (Make Sandhu/TITZ) shutter to be partly glazed with 5 mm thick tinted glass fixed with glazing clips, rubber beading/gasket anodized aluminium beading screws complete all as specified and as directed. Chowkhat Frame : 101.60x44.45x1.55 mm Shutter verticle/stile: 85.00x44.45x1.56 mm Shutter middle rail : 83.50x44.45x1.54 mm Shutter top and bottom rail : 110x44.45x1.54 mm MAKE :- (i) Anodized aluminium section : Jindal/Hindalco, Indalco (ii) Glass : Saint, Gobain, Modi Guard, TATA NOTE :- The amount include chowkhat frame, glass, shutter frame, tower bolt, sliding bolt and other nesessary items required

Supply and fix Aluminium excruded section body, door closer hydraulically regulated designation N0. 3 universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and directed.

Supply and fix 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed.

Description all as item No. 67 but exc 0.5 sq.m in each pane

Supply and fix for Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for partitions (Fixed portions) along with 5mm thick tinted glass fixed with glazing clips, rubber beading/gasket anodized aluminium beading screws, with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

Supply and fix 15 mm bore Pillar taps, cast copper alloy fancy type, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as per makes specified in PS complete all as specified and as directed.

Supply and fix one way angle cock with flange cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule for 15 mm bore of pipe complete all as specified and as directed.

Material and labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding .11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

Description as per item no.72 above but as in skirting over,including 10mm thick plaster in CM(1:4) complete.

Supply and fix sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Supply and fix 32 mm bore PVC waste pipe of approved make suitable for WHB, Urinals etc complete all as specified and as directed.

Supply and fix Vitreous china wash basin white flat back size 550x400 mm excluding taps but including 32 mm dia CP waste fitting and PVC waste pipe 610 mm long and brackets all as per makes specified in PS complete all as specified and as directed.

Supply and fix PVC connections 15 mm size with PTMT nut of length 450 mm fixed in repairs all as directed.

Material and labour Stainless steel plate rack of size 900 x 700mm, including provision for storage of plates and boxes fixed to wall complete all as specified and as directed.

Supply and fix 75mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and directed .

Supply and fix 110mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and directed .

Taking down copper/aluminium point wiring any size complete all as specified and directed .

Taking down carefully submain wiring any size complete all as specified and directed .

Taking down DB any type any size complete all as specified and directed .

Material and labour for surface point wiring with two single core PVC insulated sheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing caping of required size with all fittings and accessories alongwith one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one light point or one fan/Ex fan point controlled by one, one way switch including PVC switch board of required size for mounting of switch,regulators and casing caping terminal box for mounting ceiling rose/ holders etc complete all as specified and directed.

Description all as per item no 89 above but for One three pin 5 Amp socket outlet point on same board

Material and labour for Surface submain wiring with two single core PVC insulated sheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 2.5 sqmm (Nominal area) drawn through in and including PVC casing caping with all fittings and accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 2.5 sqmm as earth lead and connected to earth dolly incl dismentling taking down old unserviceable wiring and making good to disturbed surfaces complete all as specified and directed. NOTE :- (a) Two run of cable with one run of earth wire and one run of casing capping will be measured as one length.

Supply and fix in replacment modular switch 1 way, 5/6 Amps, 1 module (ISI marked) complete all as specified and directed.

Supply and fix in replacment modular socket, 5/6 Amps, 2/3 pin 2 module (ISI marked) complete all as specified and directed.

Supply and fix in replacment ceiling rose surface Bakelite three terminal complete all as specified and directed.

Supply and fix in replacment Sheet metal Enclosure MCB DB SPN 04 way Double door 200 Amps rated bus bar , 240 Volts AC complete all as specified and directed.

Supply and fix in replacment MCB, SPN 32 amps, 240 Volts, 10 KA ‘’C” curve complete all as specified and directed.

Supply and fix in replacment MCB, Single Pole, 5 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve complete all as specified and directed.

Supply and fix in replacement LED Light batten 20 watt, 4 feet AC sleek and seamless profiled extruded polycarbonate batten with an efficient diffuser to illuminate work and retail spaces with three core flexible copper conductor cable from ceiling rose complete all as specified and directed.

Supply and fix in replacement LED Luminaire 600x600 mm 35/36 watt 220 V AC recessed type with high efficiency, PMMA diffuser soft glare light complete with driver holders and LED Lamp suitable for roof ceiling including connection up with driver three core copper conductor of suitable size complete all as specified and directed.

Supply and fix in replacement exhaust fan made of sturdy engineering plastic complete with louvers and shutter voltage 230 volts 50 Hz copper winding of sweep 300mm complete all as specified and as directed. NOTE :- Old UNSV Exhaust fan will be deposited to MES store

UNIQUE ENGINEERS (BID ID -3403598)

Suraj Sukhdev More (BID ID -3404275)

DARSHAN ENTERPRISES (BID ID -3403465)

L.K.R.TIWARI CONSTRUCTION (BID ID -3404231)

MANIYA CONSTRUCTION CO (BID ID -3404297)

Mukund Engineers and Contractors (BID ID -3404258)