ADDL/ALTN TO BLDG NO P-53 (COOK HOUSE) FOR UP GRADATION INTO MODERN COOK HOUSE OF 213 RKT REGT AND SPL REPAIR TO TOILET BLOCK NO 222, 225, 227 AND REPLACEMENT OF EXISTING SEWEGE LINES ALONGWITH SEPTIC TANK OF SATA REGT AT NASIRABAD MIL STN

Amount

Taking down cement or cement lime plaster on stone/brick wall, ceiling incl. Raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M& L for rendering in cement mortar (1:6), 15mm thick on stone masonary surfaces finished fair and even complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on stone masonry, external surfaces finished fair & even complete all as specified and directed.

M & L for rough cast plaster mix with crusted stone (6-10 mm), sand and cement in the ratio 1:1:1 , over 15mm thick rendering in CM 1:4 as in under coat including dubbing coat (if required) complete all as specified and directed.

M&L for rendering in cement mortar (1:4) 10mm thick as in ceiling surfaces finished fair and even complete all as specified & directed.

M & L for preparation of newly plastered surfaces of walls & applying three coat of white wash complete all as specified and directed

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed

M & L preparation new plastered/rough cast surfaces of walls and providing two coat of cement base paint complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

Supply only water proofing compound ISI Marked complete all as specified and directed.

M&L glazed ceramic coloured tiles, size 450 mm X 300 mm, 7-8 mm thick on vertical surfaces of wall such as dados, skirting etc set & jointed in neat slurry and pointed in white or colour cement to match over 10 mm incl thick screed plaster in CM 1:4 complete all as specified and directed

M & L for Non-skid Ceramic tiles 7 to 8 mm thick ( square /Rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured in white or coloured cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6) complete all as specified and directed.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion ordered and complete all as specified and directed.

M&L for Random Rubble stone walling uncourses, built in CM (1:6) complete all as specified and directed.

All as per the item No 15.00 above but except stone/brick complete all as specified and directed.

M&L for brick work with flyash bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc 20mm complete all as specified and directed.

Demolition of Stone slabs & tiles of any description or thickness in floors , aprons etc, complete all as specified and directed.

M & L for 50mm sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4, complete all specified and directed

M&L 50mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection finished fair even laid in alternate bays n.exc 2m in length incl joint filling complete all as specified and directed.

M&L 75mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in plinth protection finished fair even laid in alternate bays n.exc 2m in length incl joint filling complete all as specified and directed.

Taking out old unserviceable water closet (squatt pattern) and S & F Vitreous China, Squatting pan Orissa pattern size 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) with Vitreous China ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe , including PCC (1:2:4) type B-1 for fixing of WC and making good the floor to match the existing complete all as specified and directed.

S & F vitreous china wash down water closet pan EWC (pedestal pattern) white incl fixing bolts & seat cover etc but excluding flushing cistern and flush pipe complete all as specified and directed

Taking down old unserviceable flushing cistern S&F PVC valveless syphonic action type low level flushing cistern, 10 Ltrs capacity . White, with inlet ball valve, float, handle with 32mm PVC flush pipe, fixed on walls by driling holes and using PVC rawl plug of suitable size complete all as specified and directed.

Taking down old unserviceable PVC connection and S & F PVC connection, heavy duty 15 mm bore, 45 cm long with two Nos PTMT nuts at both ends of approved quality complete all as specified and directed

S&F in repair Soap dish any type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as specified and directed.

Taking out old un serviceable tubular towel rail & S&F tubular towel rail aluminium anodised 20mm dia 'D' type 60cm long between flanges complete all as sped & directed.

S&F in repairs Chromium plated Angle/stop cock 15 mm dia screwed down light pressure screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repairs Chromium plated bib taps, with capstan heads, screwed down for iron pipe or for brass ferrule & fixed for 15 mm bore pipe complete all as specified & directed.

Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

All as per the item No 32.00 above but 20 mm bore

All as per the item No 32.00 above but 25 mm bore

S & F water tubing 15 mm bore, medium weight, ISI marked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed.

All as per the item No 33.00 above but 20 mm bore

All as per the item No 33.00 above but 25 mm bore

Refixing only 15mm bore old GI tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, Tee, union, socket, reducer etc. complete all as specified and directed.

All as per the item No 34.00 above but 20 mm bore

All as per the item No 34.00 above but 25 mm bore

S&F CI Nahani/Floor trap 75 mm outlet,with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) as in repairs complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each and removing from site complete all as spd & directed and making good disturbed surface of walls in cement mortar (1:3) complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) complete all as specified and directed.

M & L for rolled mild steel work angle iron as in storage tank stagging & cooler stand including weldeding confirming to Fe-290 with clean sharp sand complete all as specified and directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge

S & F factory made solid pannel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded. sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawings on page 146 of SSR Part - II 2004 complete all as specified and directed.

S&F of 30mm thick factory made solid frame of PVC skelton door shutter (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain, wire gauzed i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be elded to M.S. tubes. The wire gauge shall be stretched to tighten firmly PVC sheet for top rail, lock rail & bottom rail on either side and joined together with solvent cement, complete all as specified and directed.

S & F solid PVC door frame of size 50mm x 95mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing complete all as specified and as directed by the Engineer-in-Charge

S & F Steel window/ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note: Wire mesh and sheet glass shall be measured & paid separately under respective items.

S & F 300mm long aluminium alloy,anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S & F extruded aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S&F SS butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as specified and directed.

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or girth & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as specified and directed.

S&F 3.00 mm thick sheet glass, ordinary / figured quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as specified and directed.

Dismantling of existing unserviceable water tank of any description capacity exc 500 Ltr but n.exc 1000trs capacity each complete all as specified and directed

S& F rotational moulded synthetic (HDPE) water storage tank 1000litre capacity hoisted & fixed in position all as specified in SSR Part-I complete all as specified and directed.

S&F ball valves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore compete (Minimum weight 210 gm) complete all as specified and directed.

S&F in repairs gun metal globe or gate valve, wheel head cast copper alloy screwed down light pressure with crutch or butterfly handle screwed both ends for iron pipe or for union 25 mm dia, ISI marked complete all as specified and directed.

Taking down existing unservicable treatment of any description including cement plaster/conctrete any thickness from roof surface cleaning of roof surfaces and and preparing it for further treatment and removing rubbish from the site up to 50 mtrs complete all as specified and directed.

M&L for screeding 10mm thick in CM 1:4 on fair faces of RCC /stone patti roof surface finished fair & even without using extra cement even complete all as spescified and directed.

M & L for five layered roof treatment with APP modified polymeric water proofing membrane, 2mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3 Kg/ Sqm applied with bonding material using belown type bitumen conforming to IS-702 Grade 85/25 @ 1.20 Kg/ Sqm over bitumen primer conforming to IS- 3384 @ 0.40 Kg/ Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg/ Sqm over APP membrane with all overlaps complete all as specified and directed.

M&L for 40mm thick (average consolidated thickness) PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion complete all as specified and directed.

M&L for PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in surface channel and drain etc complete all as specified and directed.

Taking down 100mm / 75mm dia CI/PVC (SWR) pipe (any size or pattern) including all fitting, heads, shoes, bends and removing from sites complete all as specified and directed. (Note :- Measured over all as fixed along the centre line over the fittings and accessories).

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new PVC clamps complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber joints fixed to wall or laid in floors / trenches with & including existing / new PVC clamps complete all as specified and directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal with access door with cement joint complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F 110mm bore PVC (SWR) bend / shoe of any radius with access door, complete all as specified and directed.

S&F vitreous china wash hand basin white, flat back of size 550x400mm excl taps, and plug and porcelain stopper but incl brackets, PVC waste pipe & PVC waste coupling complete all as specified and directed.

S&F 300mm ordinary Mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F vitreous china white wash basins, flat back size 630x450mm incl waste pipe, brackets, and connecting pipe complete all as specified and directed.

M&L 75mm thick cement concrete type D-2 1:4:8 (40mm graded stone aggregate ) as in floors / pavings complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment coloured, reflective type of approved quality complete all as specified and directed.

M&L for sand filling under floor in foundations inclding watering and consolidation complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) vent cowl complete all as specified and direted.

Excavation in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes,sewage line pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil, complete all as specified and directed.

M & L for removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

M&L Septic tanks, LLDPE Septic tank designed to carry sewage and sullage water, with upflow filter incl medium excavation in any type of soil In PCC 1:4:8 below foundation ,vent shaft ,connection, etc., for 30 users complete all as specified and directed.

M&L Soakage wells exc, in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25/ RR masonry / Filling with brick bats, complete of size 2.4 M dia X 3.0 M deep complete all as specified and directed.

M&L for 150mm dia SGSW drain pipes laid in trenches and jointed complete all as specified and directed.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid with PCC 1:4:8 type D-2 for pipe of 150mm dia bore complete all as specified and directed.

Dubbing out average 10mm thick in CM 1:4 on irregular faces of walls or concrete chajjas etc complete all as specified and directed.

M & L for complete removal of existing treatment and preparation wall surfaces and providing three coat of white wash complete all as specified and directed.

M & L for complete removal of existing treatment and preparation wall surfaces and applying two coats of 1st quality acrylic distemper over 1 mm thick wall care of putty complete all as specified and directed

M&L for preparation of new plastered surfaces and Distempering with 1st quality acrylic distemper(ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, ofrequired shade and colour complete, as permanufacturer's specification. Two or more coatson new work over 1 mm thick wall care putty complete all as specified and directed

M&L for machine cut Kota stone slab flooring 20-25mm thick over 15mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the smooth of the slab incl rubbing & polishing complete all as specified and directed.

Demolition of floor hearth or wall tiling including cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises. complete all as specified and directed.

M&L for vitrified ceramic tiles light shade8-10mm thick (square / rectangular ) polished, area of each tiles exc 0.18 Sqm not exceeding 0.36 Sqm, in floor etc set and jointed in neat cment slurry and pointed in white or coloured cement to match including screed bed 15mm thick in CM 1:6 complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 8-10mm thick (square / rectangular ) polished, area of each tiles exc 0.18 Sqm not exceeding 0.36 sqm, in vertical surfaces such as skirting, dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed plaster 10mm thick in CM 1:4 complete all as specified and directed.

M&L for cement 25 mm thick PCC (1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified & directed.

M & L for 20mm thick black/any colour granite on kitchen platform and similar work(size not less than 900 x 450mm over & including 15mm thick screed bed in CM 1:6 laid over sand stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified & directed.

S&F in repairs PVC flexible waste pipe of approved quality 32mm bore, 65cm long with one end socketed fixed to waste coupling including one PVC reducer 32mm complete all as specified and directed.

S&F in repairs 125mm dia PTMT grating doom shape with centre or side hole (Mini Wt 40 grms) complete all as specified and directed.

S & F second class HW 35mm thick, factory made, plain framed, paneled shutter (Three panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned & chemically pressure treated complete all as per specified and directed.

M&L for aluminium powder coated door frame and shutter including top, bottom/middle rail using glazing clip including rubber head and float glass 6mm thick tinted provided with one floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty fixed to aluminium door and other fittings like handle, locking system, push plate and necessary beading all around the door shutter frame as required for resistance complete all as specified and directed and as per Chief Engineer Drg

M&L for aluminium powder coated sliding window, ventilator three track including aluminium powder coated decorated grill sliding shutter 5mm thick tinted float glasses, necessary aluminium beadings fittings and other panels to prevent air from out side complete all as specified and directed and as per Chief Engineer Drg

S&F door closure hydraulically regulated designation No-3 universal type suitable for door shutter of 851 to 1000mm in width of aluminium body (die cast) weight between 61 to 80 kg in repair complete all as specified and directed

S&F in repair fancy type 20mm dia aluminium curtain rods powder coated fixed to bracket complete all as specified and directed.

S&F decorative type knobs with bracket of MS powder coated fixing at end of pelmet rod complete all as specified and directed.

M&L 40 mm thick sand stone slabs; set and jointed over joists etc. in CM 1:4 as in base of water tank and M&L 25 mm thick PCC 1:2:4 type B-0 using 12.5mm stone crushed agg (for providing bottom base of PVC tank) complete all as specified and directed.

Taking down old unserviceable Chinaware sink and S&F steel made of stain less steel 1mm thick kitchen or laboratory with plugs and double Bowel , washers and waste including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union overall size not less than 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Dismantling asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified and directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws fixed with L & J hooks and washers, in roofs, walls etc with grade of zink coating 275 complete all as specified and directed

S & F rolled mild steel as in angle setion, fixed indepenntly with or without connecting plates or welding with existing steel or iron surfaces etc and similar work confirming to Gde E-165 (Fe 290) including necessary cutting, welding etc and fixing in position complete all as specified and directed.

M & L for preparation of old wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

Fabrication & fitting of kitchen with cabinet/shelves & wardrobe/cupboard made out of 18mm thick (one side decorative lamination & other side baancing lamination) PVC sheet with piano hinges including providing cabinet for keeping baskets / cutlery baskket with handles/door shutters complete all as specified and directed. Note :- PVC sheet, fitting & fixture will be measured and paid separately as supply only.

Supply only in repairs 18mm thick (one side decorative lamination & other side baancing lamination) solid PVC board with cement solvent adhesive for shutter/kitchen cabinet / cup board/partition wall/ wall cabinet complete all as specified and directed. Make :- Raj shree or equivalent as approved by GE.

Supply only soft close clip on hinge bright finish complete all as specified & directed.

Supply only 125 mm dia oval shape brass handle fancy type bright finish complete all as specified & directed.

Supply only in repair stainless steel basket (plain) of approved quality of size 520 X 485 X 100mm complete all as specified and directed. Make :- Godrej SS 304

Supply only in repair stainless steel plate basket of approved quality of size 520 X 485 X 150mm complete all as specified and directed. Make :- Godrej SS 304

Supply only basket / trolly channel 50cm long extruded MS galvanised over roller complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

Disconnecting and taking down unserviceable sub main wiring of any size including steel/PVC conduit and accessories & removing from site and making good the disturbed surfaces, complete all as specified and directed.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets etc for re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame for suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for the following, complete all as specified and directed:

All as per the item No 116.00 above but One light point controlled by one, one way switch.

All as per the item No 116.00 above but One exhaust fan controlled by one, one way switch.

All as per the item No 116.00 above but One three pin 5 Amp socket on same board with other switches.

All as per the item No 116.00 above but One three pin 5 Amp socket on independent board.

All as per the item No 116.04 above but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth complete all as specified and directed.

S&F of modular switch 1 way 6/10Amp, 1 module, complete all as specified and directed.

S&F of modular switch 1 way 16Amp, 1 module, complete all as specified and directed.

S&F of modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F of modular socket 6Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F switch piano flush type 5 amps, single pole one way 240 volts complete all as specified and directed.

S&F switch piano flush type 15 amps, single pole one way 240 volts complete all as specified and directed.

S&F Socket outlet 3 Pin 5/6 Amp flush type complete all as specified and directed.

S&F socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type ISI marked complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as specified and directed.

S&F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed. Make : Cona / SSK / Havells

S&F LED box type tube light fitting 20 watt made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body, PC diffuser and inbuilt driver, double sided connection, complete with all accessories internally prewired complete all as specified and directed.

S&F exhaust fan, steel body AC single phase, 230V of size 300 mm sweep with blades and frame and louvers complete all as specified and directed.

S&F LED light fittings, 10 W bulk head luminaries 230V, 50 Hz complete with all accessories and including connecting up with three core copper conductor cable with suitable size complete all as specified and directed.

S&F and testing energy saving street light luminaire 25 watt LED , pressure die cast housing with high power LED as lighting source and lens embedded PC cover with IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge.

S&F street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

M& L for TV Socket incl PVC conduit and co axial cable wire complete all as specified and directed.

S & F of MCB SPN, 240 volt, 06 to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SP, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, 5 Star rated & Glass lined enamel coated incoloy heating element, Temperature indicating dial & Shock-resistant ABS outer body complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed. Make: Bajaj, Havells, Usha.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle complete all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing .

Taking down existing exhaust fan & wall mounted fan and re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core complete all as specified and directed.

S&F tubes medium grade GI tubing 20 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection complete all as specified and directed.

S&F tubes light grade GI tubing 40 mm dia with all fitting laid in trenches, fixed on pole/on wall for cable protection complete all as specified and directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed.

Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and as directed.

R.S BUILDERS

GOMA CONTRUCTION COMPANY

H M LAXMINARAIN

SHREE BALAJI TRADING CORPORATION

V K LAKWAL CONSTRUCTION

TANISHQ ENTERPRISES

JWALA ENTERPRISES

M/S JAGDISH PRASAD AIRUN