Periodical Renewals to Khammam-Yellandu road from km.19/6-20/6, 21/2-22/2, 25/4-6, 26/0-4 in Khammam District (working reach from km.21/1-23/3, 25/4-6, 26/0-3). Sub-Work:-Providing Road Safety Interventions.

Supplying of hot applied thermoplastic road marking compound, 2.5mm thick including reflectorising glass beads @ 250gms with Reflectorising Glass Beads on Bituminous Surface at 250 gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass bead as per IRC: 35, the material should be of BERGER Company/ BERGER Equivalent and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference. The applied panel 7/8 number must be submitted for checking up the white index in the department lab. In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied products at site against the approved panel. In case of any major deviation, beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). b) Luminance factor of the material should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS3262, Part-1, 1989 and should pass at the range of '0' degree centigrade to -10' degree centigrade D) Adhesion: Strong E) Softening point: 102 degree centigrade F) Dried film finish: Smooth and uniform G) Night Vision: High as directed by the Engineer-in-Charge and confirming to IS: 164-1961 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-1997

Supplying of hot applied thermoplastic road marking compound, 2.5mm thick including reflectorising glass beads @ 250gms with Reflectorising Glass Beads on Bituminous Surface at 250 gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass bead as per IRC: 35, the material should be of BERGER Company/ BERGER Equivalent and must comply with the following: a) White index for the product should be in the range of 60-70 when measured against standard reference. The applied panel 7/8 number must be submitted for checking up the white index in the department lab. In case the department approves the white index of any vendor, the department engineer may carryout random checking of the applied products at site against the approved panel. In case of any major deviation, beyond acceptance limit, department reserve the right to cancel or reject the total supplied consignment of the said material and will compell the vendor has to replace the full consignment by the desired material as per approved panel at his own cost and additional demurrages may be claimed due to loss of man days (as per the rules of the department). b) Luminance factor of the material should be in the range of 80-85% at 45 degree centigrade as per AASTHOM 249. c) Crack resistance: The applied panel cured for 7 days under ambient condition and then should be tested as per BS3262, Part-1, 1989 and should pass at the range of '0' degree centigrade to -10' degree centigrade D) Adhesion: Strong E) Softening point: 102 degree centigrade F) Dried film finish: Smooth and uniform G) Night Vision: High as directed by the Engineer-in-Charge and confirming to IS: 164-1961 (1st revision reaffirmed in 1986) and clause conforming to IRC 35-1997(6 Conservative lines 7.5 mm thick)

Providing and fixing Reflecting pavement markers (Road studs) made of plastic body moulded tom HIPS (Hi-imopact polystyren) of ABS or ASA (Acrylic Strean Acrylonitrite) and reflective panels shall consist of number of lenses containing single or double prismatic cubes capable of providing toral internal reflection of teh light entering the lens face and conforming to ASTM, BS and complying to guidelines isssued by MOST circular no. RW/NH-33023/10/97 - DO III Dt: 11.06.1997. The height, width shall not exceed 20mm, 130mm and teh area of each retro -reflecting surface shall not be less than 13 sqcm. and terh slope of retro-reflective surface shall prefeable be 35+/-5 degree to base. Fixing will be with ounails and reflective markshall be fixed to the road surface using the adhensives and teh procedure recommende by teh manufacturer and as per para 6.2 of the MOST circular including cost and conveience of all materials, equipment, machinary and labor with all leads and lifts, laoding, unloading chrges, site clearence etc. and complete necessary for successful completion of teh work as directed by the Engineeer-in-Charge.

Providing and fixing Mandatory / Regulatory sign boards size 600 mm circle made out of Type -XI of ASTMD 4956-09 wide angle cube cornered micro Prismatic Retro reflective sheeting and confirming to IRC 67:2012 for full background of White colour and letters/logos done by screen printing in Black colour, boarders by screen printing in Red colour and fixed over 3MM Alluminium Composite Material sheet having minimum 0.30mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of M.S angle 25x25x3mm all round and fixing with 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level to the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paint Black and White colour with bands of 30cm of height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials, equipment, machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by Engineer-in-Charge.

Providing and fixing Village name board size 800x600 mm made out of Type - XI of ASTMD 4956-09 High Intensity Prismatic Prismatic Retro reflective sheeting and confirming to IRC 67:2012 for full background of Green Colour & White Letters and fixed over 3MM Alluminium Composite Material sheet having minimum 0.30 mm thick Aluminium skin on both sides with back side painted grey colour and fixed over back support frame of M.S angle 25x25x3mm all round and fixing with 35x35x4mm and mounted on a MS angle post of size 75x75x6mm with clear height of not less than 2.1 m from the ground level to the bottom of the board. The signpost should be painted with one coat of red oxide paint and 2 coats of synthetic enamel paint Black and White colour with bands of 30cm of height. The signpost shall be firmly fixed with MS base angle 35x35x4 mm in to the ground by M-15 Concrete foundation of size 450x450x600mm including cost and conveyance of all materials, equipment, machinery and labour with all leads and lift, loading charges necessary for satisfactory completion of the work as directed by Engineer-in-Charge.