ADDITION ALTERATION AND SPECIAL REPAIRS TO BLDG NO. P-88 AND P-89 AT NOFRA, MUMBAI

Amount

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. including erection of double steel scaffolding, covering with green cloth and all the safety measures/precautions and remove the debris outside of MoD land (as per directions of BMC) complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Material & Labour for chipping, removing carefully concrete work by low impact hammer, breaker without damaging the structure & cleaning, including erection of double steel scaffolding, covering with green cloth and all the safety masures/precautions and removal of debris outside of MoD land (as per directions of BMC) complete all as specified and directed by the Engineer-in-charge. Note: Hard concrete should not be removed by force.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas, parapet wall, chimney, wall and similar suspended work including cutting of reinforcement cut as required to facilitate demolition including removing of debris out side MoD land complete all as specified and directed by Engineer-In-charge. (Reinforcement cut as required to facilitate demolition)

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Cleaning the existing reinforcement with wire brush/ rotary wire brush to make surface free from rust scales, loose material, dirt etc. complete and providing, applying two coats of alkaline rust converting primer conforming to ASTMB-117, on the existing rebars and allowing it to react with rust for 6 hrs and form a corrosion resistant, insoluble and adherent protective layer, including cleaning the reinforcement, wirebrushing to remove loose rust spalls, with time interval of 1 hour between the coats.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Replacement of steel reinforcement with TMT bars of appropriate dia where 20% of cross section is reduced including dismantling of rusted steel and application of rust converter Krishna Conchem FEOVERT or any other techno-commercial equivalent and applying protective coating IP Net RB or any other techno commercial equivalent complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Providing and application of hitech concrete penetrating, water based, organic, Bi-polar, calcium nitrite free, migratory corrosion inhibitor on concrete surface having pH 9.5 which migrates to a virtual extent of 100 mm inside concrete through pores, to inhibit the corrosion process on embedded steel at both anodic and cathodic ends by depassivating the electro-chemical reaction in that region thereby protecting rebar on all sides.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Grouting injecting low viscosity high molecular weight thermosett polymer Monopol 250 H by pressure and using pressure epoxy injector with accessories till nozzles refused to accept the grout, including mixing material components part a and part b in required quantities as per manufacturer's instructions by weigh batching. Filling the grouting gun with monopol 250 H and maintaining desired pressure in the gun, air compressor and at exit (minimum 3 to 4 kg/sqcm) by a mechanism to monitor both pressure gauges and controlling the same by release valves and release the grout as per requirement simultaneously to grout the structural element through prefixed nozzles till its refusal. Seal the nozzle with thixotropic epoxy putty after the refusal. Note: Leakages through other nozzles or cracks are required to be monitored while grouting and such points to be sealed as and when required without any extra cost. Make: Fosroc conbextra EP 10 or any other techno-commercial equivalent in makes as mentioned in Particular Specifications.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Mixing and applying SBR latex modified cementitious bond coat using cement 2.2 kg per square metre on prepared concrete surfaces of parent material complete all as specified and as directed by the Engineer-in-charge. (Note: SBR latex shall be paid for separately).

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Mixing and applying SBR latex modified cement mortar 30 mm thick in cement sand mortar in proportions of 1:3 (1 part cement and 3 parts quartz aggregate) with polymer admixed in proportions as approved, including trowelling with wooden tools on prepared concrete surfaces of parent material complete all as specified and as directed by Engineer-in-charge. (Note : Rate includes the rate of steel scaffolding. No separate payment shall be paid for scaffolding). (Note: SBR latex will be measured and paid separately as supply only).

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Rebuilding the section of damaged RCC elements to required size avg thickness upto and including 50 mm by providing and casting with microconcrete of grade M-40 or above including providing and fixing of watertight shuttering of minimun 12 mm thickness with supporting framework, all lead lift, mixing, placing, deshuttering, levelling the surface by grinding off cementitious slurry or construction joint differences if any to satisfaction of the Engineer-in-charge, etc. complete.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Providing and applying fair finish 20mm thick plaster in two layers i.e 15mm thick base coat and 5mm thick finishing coat with ready mix prepacked proportioned dry mix mortar, mixed with liquid water proofing compound on fair faces of brick wall or concrete surfaces, on internal surfaces including transporting of material, mixing, curing, etc. complete all as specified and directed by the Engineer-in-charge. Note :- Liquid water proofing compound shall be measured and paid seperately as supply only.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Providing and applying fair finish 15mm thick plaster with ready mix prepacked proportioned dry mix mortar, mixed with liquid water proofing compound on fair faces of brick wall or concrete surfaces, on internal surfaces including transporting of material, mixing, curing, etc. complete all as specified and directed by the Engineer-in-charge. Note :- Liquid water proofing compound shall be measured and paid seperately as supply only

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Providing & applying anti algal water-based elastomeric exterior wall finish on newly plastered surfaces including surface preparation, applying suitable wall prime seal primer 8-10 sqm per ltr coverage area and application of two coats (base coat 4.2-4.7 & top coat 6-6.5 sqm per ltr coverage area ) & of paint by roller etc. complete all as specified and directed by the Engineer-in-charge. Notes:- 1. Work will be executed by authorised applicator of approved manufacturer. 2. Every coat of finish will be approved by GE before starting new layer/coat. 3. Both buildings are of vintage type of 1988 and are structurally sound. 4. Contractor to submit minimum 05 yrs warranty certificate from the company.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Providing and applying fair finish 15mm thick plaster with ready mix prepacked proportioned dry mix mortar fair faces of brick wall or concrete surfaces additives, on ceiling including transporting of material, mixing, curing, etc. complete as per direction of Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Providing and applying fair finish 10mm thick plaster with ready mix prepacked proportioned dry mix mortar fair faces of brick wall or concrete surfaces additives, on ceiling including transporting of material, mixing, curing, etc.complete as per direction of Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

(a) Material & Labour for waterproof cement based putty @ 1 kg (undiluted) per sqm of average thickness 2 mm over the newly plastered surface of wall, after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps :- Step 1:- Mix the putty powder by adding water as per manufacturer's instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2:- Apply the first coat of the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI. Step 3:- Allow 6-8 hrs time to dry the putty surface. (b) Material & Labour for applying two coats of oil bound distemper over a coat of primer using fully automatic airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 Metre. The spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed by the Engineer-in-Charge. Note: Sanding of surface to be done by mechanical sander with 1500-2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper masking to be carried out before primer and paint application.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

(a) Material & Labour for waterproof cement based putty @ 1 kg (undiluted) per sqm of average thickness 2 mm over the newly plastered surface of ceiling, after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps :- Step 1:- Mix the putty powder by adding water as per manufacturer's instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2:- Apply the first coat of the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI. Step 3:- Allow 6-8 hrs time to dry the putty surface. (b) Material & Labour for applying two coats of oil bound distemper over a coat of primer using fully automatic airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 Metre. The spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed by the Engineer-in-Charge. Note: Sanding of surface to be done by mechanical sander with 1500-2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper masking to be carried out before primer and paint application.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

(a) Material & Labour for waterproof cement based putty @ 1 kg (undiluted) per sqm of average thickness 2 mm over the old plastered surface of wall, after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps :- Step 1:- Mix the putty powder by adding water as per manufacturer's instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2:- Apply the first coat of the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI. Step 3:- Allow 6-8 hrs time to dry the putty surface. (b) Material & Labour for applying two coats of oil bound distemper over a coat of primer using fully automatic airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 Metre. The spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed by the Engineer-in-Charge. Note: Sanding of surface to be done by mechanical sander with 1500-2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper masking to be carried out before primer and paint application.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

(a) Material & Labour for waterproof cement based putty @ 1 kg (undiluted) per sqm of average thickness 2 mm over the old plastered surface of ceiling, after scrapping to prepare the surface even and smooth complete and sanding of the putty surface with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surface free from dust etc. by skilled labour as per following steps :- Step 1:- Mix the putty powder by adding water as per manufacturer's instructions and mix it with putty mixer with the mixing capacity of min 2.5 kg putty per minute. Step 2:- Apply the first coat of the prepared mixer with the help of fully automatic airless spray machine of putty application having flow speed of max 6 ltrs per minutes with a maximum pressure 3300 PSI. Step 3:- Allow 6-8 hrs time to dry the putty surface. (b) Material & Labour for applying two coats of oil bound distemper over a coat of primer using fully automatic airless spray technology with max working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 Metre. The spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying distemper should be able to spray in hard to reach areas and penetration of distemper on the surface complete all as specified and directed by the Engineer-in-Charge. Note: Sanding of surface to be done by mechanical sander with 1500-2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. Proper masking to be carried out before primer and paint application.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Material & Labour for complete removal of extsiting treatment on walls/surface with wire brush/rotatry wire brush, watering, cleaning of surface and opening of cracks in V shape and filling with Dr. Fixit (Crack X Paste) or any other techno-commercial equivalent in Fosroc, Krishna Conchem, etc. as approved by the Engineer-in-charge and applying anti-algae water based elastomeric exterior wall finish as on old plastered surfaces including surface preparation, applying suitable wall prime seal primer 8-10 sqm per ltr coverage area and application of two coats (base coat 4.2 -4.7 & top coat 6-6.5 sqm per ltr coverage area) & of paint by roller etc. complete all as specified and directed by the Engineer-in-charge. Notes:- 1. Work will be executed by authorised applicator of approved manufacturer. 2. Every coat of finish will be approved by GE before starting new layer/coat. 3. Both buildings are vintage of 1988 and are structurally sound. 4. Contractor to submit minimum 05 yrs warranty certificate from the company.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete, conforming to Fe-410 Gde E-250 quality A, complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Material & Labour for uprooting of small plants/roots from walls and using chemical to permanently destroy the roots and making good the disturbed surface with brick work in Cement Mortar 1:4 and plastering in Cement Mortar 1:4 on both sides of wall of surface area not exc. 30cm x 30 cm complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

DIsmantling Cast iron pipe of 100mm bore fixed on wall or floor at any floor including all fittings complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

DIsmantling Cast iron pipe of 75mm bore fixed on wall or floor at any floor including all fittings complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall or laid in floor jointed with neat solvent with dash through fasteners and rain water bracket suitable for 110mm pipe spacing 1.5m c/c as per CE (Navy) Mumbai TD No TD/2023/01 complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing PVC (SWR) 75mm bore pipes single socketed in any length with rubber ring joints fixed to wall or laid in floor jointed with neat solvent with dash through fasteners and rain water bracket suitable for 110mm pipe spacing 1.5m c/c as per CE (Navy) Mumbai TD No TD/2023/01 complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing 75mm PVC (SWR) branch piece (Tee), double (equal) or unequal, ordinary or inverted (spigot or socket type) of with parallel branches with oval access door and jointed with neat solvent to PVC pipes fixed to wall or in floor including all fittings and fixed as in repairs, complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing 110mm PVC (SWR) branch piece (Tee), double (equal) or unequal, ordinary or inverted (spigot or socket type) of with parallel branches with oval access door and jointed with neat solvent to PVC pipes fixed to wall or in floor including all fittings and fixed as in repairs, complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing in repair 75mm PVC (SWR) floor trap with SS grating including jointing to waste pipe with solvent to PVC pipes fixed to wall or in floor in cement concrete type B1 (1:2:4) complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing in repair 110mm PVC (SWR) ‘P’ or ‘S’ Traps jointed with solvent fixed to wall or floor including all fittings complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing as in repairs 110mm PVC (SWR) sanitary connections short connections pipe of length upto 300 mm, complete all as specified.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing 75mm PVC (SWR) Bends diminishing pieces or tapers (larger bore measured) with oval access door and jointed with neat solvent to PVC pipes fixed to wall or floor including all fittings complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing 110mm PVC (SWR) Bends diminishing pieces or tapers (larger bore measured) with oval access door and jointed with neat solvent to PVC pipes fixed to wall or floor including all fittings complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing 75mm bore PVC (SWR) vent cowl complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 110mm bore PVC (SWR) vent cowl complete all as specified and directed by the Engineer-in-charge.

Taking down rain water pipes/ PVC pipes/ cemented pipe (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing PVC (SWR) branch piece, Single (single Y) equal or unequal for 75 mm bore access door eye complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing PVC (SWR) 160mm bore pipes single socketed in any length with rubber ring joints fixed to wall or laid in floor jointed with neat solvent with dash through fasteners and rain water bracket suitable for 110mm pipe spacing 1.5m c/c as per CE (Navy) Mumbai TD No TD/2023/01 complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing 160mm PVC (SWR) Bends/shoes diminishing pieces or tapers (larger bore measured) with oval access door and jointed with neat solvent to PVC pipes fixed to wall or floor including all fittings complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing PVC (SWR) branch piece, Single (single Y) equal or unequal for 160 mm bore access door eye complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposal of debris out side the MoD land etc. complete all as specified and directed by the Engineer-in-charge.

Material & Labour for coloured non-skid ceramic tiles 7-8mm thick rectified glossy (square/rectangular) of size 300mmX300mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed by the Engineer-in-charge.

Material & Labour for coloured non-skid ceramic tiles 7-8mm thick rectified glossy (square/rectangular) of size 400mmX400mm in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick rendering in cement mortar 1:4, complete all as specified and directed by the Engineer-in-charge.

Material & Labour glazed ceramic tiles coloured of size 450x300x7mm laid on vertical surface such as dado/skirting over cement mortar backing coat, set jointed in neat cement slurry and pointed in white or coloured cement including 15mm thick backing coat in cement mortar 1:4, complete all as specified and directed by the Engineer-in-charge.

Material & Labour for light shade coloured double charged vitrified tiles CAT No. Super Glossy-K6207, K6306, K6211 of Kajaria or techno-commercial equivalent as mentioned in Particular Specifications vitrified tiles of size 600mmX600mm and 9-10 mm thick (square/rectangular) polished in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed by the Engineer-in-charge.

Material & Labour for light shade coloured double charged vitrified tiles CAT No. Super Glossy-K6207, K6306, K6211 of Kajaria or techno-commercial equivalent as mentioned in Particular Specifications vitrified tiles of size 600mmX600mm and 9-10 mm thick (square/rectangular) polished in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick backing coat in cement mortar 1:4, complete all as specified and directed by the Engineer-in-charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid beded and pointed in any mortar including removal outside of MoD land complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing machine cut cudappa stone slab 20-25 mm thick laid over 15mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by the Engineer-in-charge.

Material & Labour for 18-20 mm thick jet black Granite slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms over and including bedding layer of 20mm thick in cement mortar (1:4) for laying floor finishes including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by the Engineer-in-charge.

Material & Labour for 18-20 mm thick Udaipur green/ Baroda green marble slab (of any type) work (table rubbed and polished) in floors, steps, jambs, pillars, window-cills, cooking platforms over and including bedding layer of 20mm thick in cement mortar (1:4) for laying floor finishes including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble complete all as specified and directed by the Engineer-in-charge.

Taking down chowkhats or frame (w/o taking off shutters from the frames) exc 1.50 but not exc 4.00 sqm each complete all as specified and directed by the Engineer-in-charge.

Taking down chowkats or frame (w/o taking off shutters from the frames) not exc 1.50 sqm each complete all as specified and directed by the Engineer-in-charge.

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each and complete all as specified and directed by the Engineer-in-charge.

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each and refixing in the same opening after easing and adjusting complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 2nd class hard wood plain, solid straight chowkats and frames, wrought framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by the Engineer-In-charge.

Supply & Fixing 2nd class hard wood 35mm thick factory made plain framed, panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial or 12mm veneered particle board with commercial veneer on both faces. The size of rail and stile as per IS 1003 (Part-I) kiln seasoned and chemically pressured treated complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 2nd class hardwood 35mm thick skelton shutters, open rebated and prepared to receive wire mesh edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing mesh etc, sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed by the Engineer-In-charge.

Supply & Fixing for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with SS dash fasteners of required dia and length complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed by the Engineer-in-charge. Note: Stainless steel butt hinges shall be paid separately.

Dismantling boarding of any description fixed in any position with screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 18/19 mm thick prelaminated partical board interior grade prelaminated on one side with decorative choice lamination & on other side balancing white lamination fixed with screws to timber frame work including 6 mm thick teak wood beading all around complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing MS holdfast, wall ties and similar articles confirming to Fe-290 Gde- E-165 complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 4.8 mm thick plain glass not exceeding 0.50 sqm each fixed to aluminium window and iron frame complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 100mm size SS butt hinges medium weight fixed with SS screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs 100mm size SS butt hinges medium weight fixed with SS screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections, fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy fixed complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections, fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy fixed complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 200mm long aluminium anodized barrel tower bolts of extruded section fixed with SS screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs 200mm long aluminium anodized barrel tower bolts of extruded section fixed with SS screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing extruded aluminium anodized alloy handle fabricated type 150mm long fixing complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs extruded aluminium anodized alloy handle fabricated type 150mm long fixing complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Aluminium 4 levers Mortice night latch with 3 keys, size 65mm complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing as in PVC cabinet with openable shutter and mirror with size of 622x422mm CAT No. 555 of Prayag or any other techno-commercial equivalent in Neelkamal or Shakti with thickness of mirror not less than 2mm, fixed to wall in repairs complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples or wooden/ Aluminium beading including removing old wire mesh complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing as in repairs Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples or wooden/ Aluminium beading including removing old wire mesh complete all as specified and directed by the Engineer-in-charge.

Material & Labour for PCC 1:2:4 B1 (20mm graded aggregate) as in bed blocks, copings, benchings, railing, bends etc including necessary formwork complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs fancy type drapery rods, powder coated aluminium of 20-25mm size with/including end brackets, and hanging arrangements etc. complete all as specified and directed by the Engineer-in-charge.

Material & Labour for aluminium anodised grill powder coated with suitable aluminium anodised frame section manufactured by M/S Deco Grill pattern DG-104 (7.5mm thick) or any other techno commercial complete all as specified and directed by the Engineer-in-charge.

Material & Labour for preparing new wooden surfaces over 10 cm of width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by the Engineer-in-charge.

Material & Labour for preparing old wooden surfaces over 10 cm of width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing wash basins, vitreous china, white, flat back, wall hung of size 560mm x 415mm x 200mm and Swan Nech Pillar tap with left hand operating knob with 450mm long braided hose conforming to model CAT No. CNS-WHT-801 and CQT-CHR-23123 respectively of Jaquar or techno-commercial equivalent as mentioned in Particular Specifications; with and including cast iron brackets [embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws], 32 mm nominal size, copper alloy, nickel chromium plated finish waste coupling and waste pipe of appropriate size and required length confirming to CAT Part No. ALD-CHR-705 of Jaquar or techno-commercial equivalent as mentioned in Particular Specifications, including painting of fittings and brackets, sealing gap between wall and wash basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings, etc. with silicone sealant complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs vitreous china wash down, white, water closet pan (wall hung pedestal pattern) with 'P' or 'S' trap with soft close seat cover, hinges, accessories set, size 365x545x360mm CAT Part No. CNS-WHT-961SPP of Jaquar or any other techno-commercial equivalent model as mentioned in Particular Specifications with 'P' or 'S' trap, closed pattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe, etc. and screwed with brass screws to sheesham wood plugs embedded in floor complete all as specified and directed by the Engineer-in-charge.

Material & Labour as in repair vitreous water closet (squatting pan, Orissa pattern, size 575x440x250mm CAT Part No. ECS-WHT-451LE in Jaquar or any other techno-commercial equivalent model as mentioned in Particular Specifications white, with integral foot rests and 'P' trap (excluding flushing cistern and flush pipe) including provision of lime concrete bedding complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs 10 litres capacity, low level, syphonic type, white, plastic twin flushing cistern conforming to CAT Part No. ESH-WHT-184NL of Jaquar or any other techno-commercial equivalent model as mentioned in Particular Specifications as per IS 7231:1994 as aprroved with inlet, ball valve, float and handle including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed by the Engineer-in-charge.

Supply & Fixing as in repairs Health faucet (ABS Body) Cat Part No. ALD-CHR-587 of Jaquar or any other techno-commercial equivalent model as mentioned in Particular Specifications mild steel chromium plated suitable for 15 mm dia pipe with 1.00 metre long spirochrome flexible tube and wall hook including making connections and fixed in position complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing as in repairs toilet paper holder CAT Part No. ACN-CHR-1153S of Jaquar or any other techno-commercial equivalent model as mentioned in Particular Specifications with flat recessed type stainless steel complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing double bowl sinks made of stainless steel with drainage board 1mm thick, kitchen or laboratory, with plugs, waste pipes, washers and wastes coupling; including bedding in cement mortar on to dwarf wall or including provision of fixing cantilever CI brackets and connecting union to pipe, also including PVC waste pipe, overall size 1370mm x 510mm with bowl size 410mm x 410mm x 230mm, complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs Stainless steel towel rack 600mm long Cat Part No. ACN-CHR-1181FS of Jaquar or any other techno-commercial equivalent model as mentioned in Particular Specifications including necessary brackets complete all as specified and as directed by the Engineer-in-charge.

Supply & Fixing stainless steel plate rack of size 900 x 580 x 210 mm fixed to wall with screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing PVC connectors of 15 mm size with PTMT nuts of length 600 mm length complete all as specified and directed by the Engineer-in-charge.

Demolition of cement concrete filling of any description in sunken portion and removing the debris outside of MoD land complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Treatment of sunken floor slab comprises of the following specifications and all as specified: (i) Material & Labour for cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. 40mm thick avg PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in padding concrete to achieve proper slope including cutting holes in bricks or RCC wall for spout (Cost cutting holes and pipes shall be measured and paid separately) (ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with integral water proofing compound @ 3% by wt of cement consumed. Fill it with water and check dampness and seepage. Where dampness/seepage is noticed, nozzles shall be fixed and grouting carried out. (WPC shall be measured & paid separately) (iii) All junctions points of side wall where CI/GI pipes are passing through shall be sealed with epoxy putty. ((iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean. (v) Material & Labour for applying two coats of polymer modified cementious water proof coating as per manufacturer's instructions to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed. (This item shall be peasured and paid separately) (vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound 3% by wt of cement consumed as per manufacturer's specification including rounding of corners and junctions sloping towards spout. (WPC shall be measured & paid separately) Note:- Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of GE. Test shall be done in presence of reps of PMG and record for Each sunken slab shall be maintained. The treatment shall be carried out by authorised applicators of chemicals. Cost of testing is inclued in the rates quoted above. (vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint (Black Japan shall be paid separetely). This item will be measured & paid separately.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Material & Labour for cutting holes in bricks or RCC walls exceeding half brick built in cement mortar including making good after inserting and setting spouts complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing GI pipe of 50mm dia medium grade laid in sunken floor complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Material & Labour for applying two coats of polymer modified cementious water proof coating as per manufacturer's instructions to bottom and vertical sides up to finished floor level+100mm height. The thickness of two layers shall be 1mm. When the second layer is still sticky, coarse sand spray shall be applied for the vertical and bottom surface of the sunken portion complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Material & Labour for PCC 1:7:12 with brick aggregate as in lean concrete/filling concrete complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Material & Labour for 75mm thick plain cement concrete type D-2 (1:4:8) as in sub base, complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Demolition of brick work built in cement mortar or cement lime mortar and removal of debris outside of MoD land complete all as specified and directed by the Engineer-in-charge.

Material & Labour for Brick work with sub class 'B' brick straight or curved on plan exc 6m mean radius built in CM (1:4) complete all as specified and directed by the Engineer-in-charge.

Material & Labour for Brick work with sub class 'B' brick straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs 0.71mm thickness plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing, crumple joints and fixed to wall with screws all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply only integral water proofing compound.

Taking up or down 80mm bore steel tubing and connections, complete all as specified and directed by the Engineer-in-charge. (Work carried out at terrace).

Taking up or down 50mm bore steel tubing and connections, complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Taking up or down 25mm bore steel tubing and connections, complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Taking up or down 20mm bore steel tubing and connections, complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Taking up or down 15mm bore steel tubing and connections, complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing 75mm inner dia bore with CPVC Schedule 80 pipes & plain CPVC Schedule 80 fitting including fixing of pipes in wall with clamps as mentioned and shown in HQ CE (N) Mumbai zone TD Drg No TD/2023/01 toTD/2023/03 complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 50mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling/laying in floors including fixing of pipes in wall with clamps as mentioned and shown in HQ CE (N) Mumbai zone TD Drg No TD/2023/01 toTD/2023/03 complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing 25mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling/laying in floors including fixing of pipes in wall with clamps as mentioned and shown in HQ CE (N) Mumbai zone TD Drg No TD/2023/01 toTD/2023/03 complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings concealed on walls/ceiling/laying in floors including fixing of pipes in wall with clamps as mentioned and shown in HQ CE (N) Mumbai zone TD Drg No TD/2023/01 toTD/2023/03 complete all as specified and directed by the Engineer-in-charge. Note:- Marking to be done with permanent marker showing the concealed pipe line to avoid breakage/damage in future. Drawing of internal pipe line (kitchen, Bath, Toilet etc.) to be submitted by the contractor.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing in repair/replacement of gun metal, globe or gate valves 80 mm size, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-In-charge. (Work carried out at terrace)

Supply & Fixing in repair/replacement of gun metal, globe or gate valves 50 mm size, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-In-charge. (Work carried out at terrace)

Supply & Fixing in repair/replacement of gun metal, globe or gate valves 25 mm size, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-In-charge. (Work carried out at terrace)

Material & Labour for cutting holes into or through brickwalls built in cement mortar not exc. 150 sqcm superficial area & making good after pipe lines are laid by using PCC (1:2:4), complete all as specified and directed by the Engineer-in-charge.

(i) From Ground floor to 4th floor

(ii) From 5th floor to 8th floor

(iii) From 9th floor to 12th floor

(iv) From 13th floor to 16th floor

Supply & Fixing in repair white rectangular PVC water storage tanks (Loft tank) of capacity 300 ltrs with complete fitting including fixing 03 Nos tank nipples of GI/ PPR with washer for outlet and inlet all as per manufacturer's instructions including disconnecting service connections/over flow pipes and removing old tank complete all as specified and directed by the Engineer-in-charge.

Supply & Fxing in repair PVC modular 20mm thick as in proflie including 'C' channels, aluminium U clip all around the profile suitable for 300 ltrs capacity loft tank, complete all as specified and directed by the Engineer-in-charge.

Disconnecting existing tanks of capacity exc. 250 but not exc. 500 litres, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required, reconnecting and re-fixing in position after cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs brass float valve flat type of size 15 mm bore, high pressure with polythene float & fly nut complete, screwed for GI pipe of following sizes including necessary GI fittings complete all as specified and directed by the Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290 Gde-E-165 complete all as specified and directed by the Engineer-in-charge.

Material & Labour for preparing of new steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, zinc chrome complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing as in repairs 15mm fancy type chromium plated Bib taps, CAT Part No. CQT-CHR-23037 of Jaquar or any other techno-commercial equivalent model as mentioned in Particular Specifications cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing as in repairs brass chromium plated shower rose 100mm dia including 160mm long shower arm casted body round shape for wall mounted shower CAT Part No. OHS-CHR-1989 and CAT Part No. SHA-CHR-477 respectively of Jaquar or techno-commercial equivalent in Parryware or Hindware, including fixed to 15mm bore pipe, complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs stop valve/angle valve fancy type CAT Part No. CQT-CHR-23053 of Jaquar or any other techno-commercial equivalent model as mentioned in Particular Specifications chromium plated screwed down, high presure with butterfly handle screwed both ends for pipe and fixed to pipe of 15mm dia bore complete all as specified and directed by the Engineer-in-charge.

Material & Labour for post construction treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with sealing compound complete all as specified and directed by Engineer-In-charge.

Supply & Fixing of Modular kitchen cabinet with following specifications: (a) 18mm thick Marine plywood, grade BWP (IS:710), type BB with both side 1mm thick decorative choice laminate type 1 of surface finish, colour and pattern as approved, as in front and shutters with aluminium profile handles. (b) Carcass made up of combination of 0.50mm (body panels) and 1.20mm thick (Horizontal stiffener & leg channels), epoxy polyester powder coating with dry film and shelves made up of 0.50mm thick galvanised steel shelves. (c) Grocery Kit: Taiming Tranquil Solid Drawer 175mm, 304 grade stainless steel wire basket 525MM, 2 Drawer solid Tranquil Drarwers 350MM each, Dish Kit : 175mm Tranquil Drawer, 175mm cup and saucer wire basket , 350MM Wire Basket, Thali Holder 350MM, 200MM bottle pull out 2 layer utility of 304 Garde Stainless Steel. Wicker basket unit 450MM cane wood, undermount soft closing channels, weight bearing capacity of 35Kg each. (d) Hetich hinges with CED coating for extended edge bending of 2mm thick, corrosion resistance. Legs: Hetich make PVC legs with adjustable heights. Hardware & Screws made up of stainless steel. (e) Skirting: 100mm Rehau make PVC Co-extruded skirting in metallic silver color or as approved. Note: Product compliant of ISO 14001/ISO 45001/ISO 50001 & IGBC Greenpro.

Supply & Fixing decorative glass corner shelf round 8mm thick, 300mm size with stainless steel railing, fixed with D type stainless steel bracket on wall of approved design and pattern complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs wall mixer CAT Part No. CQT-CHR-23273UPR of Jaquar or techno-commercial equivalent in Parryware or Hindware fancy type chromium plated suitable for 15mm dia bore pipe with fittings complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Stainless Steel Soap Dish CAT Part No. ACN-CHR-1131N of Jaquar or techno-commercial equivalent in Parryware or Hindware fancy type fixed with two Steel/ CP Screws complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing 40mm bore Forged Pressure Reducing Valve (PRV) made up of brass rugged body, piston operated with all fittings to be fixed with GI pipe upto complete to walls complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing as in repairs 15mm fancy type chromium plated two way Bib taps, CAT Part No. CQT-CHR-23041 of Jaquar or techno-commercial equivalent in Parryware or Hindware cast copper alloy with crutch or butterfly handule, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by the Engineer-in-charge.

Dismantling water tanks exc. 1000 ltrs but not exc 5000 ltrs and removing to store complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair rotational moulded polythylene water storage tanks, triple layered (ISI marked) of 3000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, including provision of necessary fittings for connecting the overflow, drain out, inlet and outlet pipes, complete all as specified and as directed by the Engineer-in-charge.

Supply & Fixing Solid 5mm thick Plain colour PVC sheet including fixing material as required such as rubber gasket etc, fixing at site in aluminum frame as per specifications complete all as specified and directedcby the Engineer-in-charge.

Material & Labour for provisioning of 02 Nos holes in each quarter for passing AC pipes and placing 75mm dia PVC pipe of length 0.50 metre, fixed with PCC 1:2:4 making surface good. Fixing PVC end cap from inside complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs Sink Cock with swinging Spout (wall Mounted Model) CAT Part No. CQT-CHR-23347 of Jaquar or techno-commercial equivalent in Parryware or Hindware fancy type chromium plated suitable for 15mm dia bore pipe with fittings and complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing as in repairs 15mm fancy type chromium plated Long Nozzle Bib tap, CAT Part No. CON-CHR-049NKN of Jaquar or techno-commercial equivalent in Parryware or Hindware cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repairs 10 litres capacity, low level, syphonic type, white, plastic flushing cistern conforming to CAT Part No. ESH-WHT-184NT of Jaquar or any other techno-commercial equivalent model as mentioned in Particular Specifications as per IS 7231:1994 as aprroved with inlet, ball valve, float and handle including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed by the Engineer-in-charge.

Supply & Fixing rotational moulded polythylene water storage tanks, triple layered (ISI marked) of 5000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I, including provision of necessary fittings for connecting the overflow, drain out, inlet and outlet pipes, complete all as specified and as directed by the Engineer-in-charge.

Supply only approved SBR Latex polymer. Name of Manufacturer: BASF/Fosroc/Sika/ Dr Fixit (Note: Rate shall be in terms of solid contents of polymer).

LIGHTENING PROTECTION

Material & Labour for GI strip 25 x 4mm for building as Lightening Conductor Horizontal, Vertical Down Conductor on insulator, Ground Ring Conductor including taking down old earthing strip (lightning protection strip) from each wing of each building and taking out from the wall/roof/pillar/earthing pit etc. complete all as specified and directed by the Engineer-in-charge.

Material & Labour in replacement air termination, single pointed aluminium rod 12mm dia and 300mm long including taking down complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos. 8mm dia 25mm long hexagon head screw including taking down complete all as specified and directed by the Engineer-in-charge.

Material & Labour for in repair maintenance free enviroment friendly earth electrode set comprising of 17.2mm dia, 3m long rod low carbon steel molecular copper bounded for a thickness of 250 micro OHMS, highly conductive ANS/INSF STD-60 certified carbon bound backfill compound which shall set like concrete according to BS 7430 & IEEE 80 (each bag shall contain 50 Ibs) complete all as specified and directed by the Engineer-in-charge.

Material & Labour for in repair PCC pit 1:2:4 type B-1, cover reinforced with XPM, weight not less than 4kg/sqm and 6mm dia bar handle earth pit angle iron frame of size 25x25x3mm complete all as specified and as directed by the Engineer-in-charge.

HOT WATER SUPPLY

Supply, fixing, testing and commissioning of instant type water heater (geyser) vertical type of 03 Ltrs capacity, single phase, rust Resistant, ABS body stainless steel inner tank with thermal cut off with power consumption 3000 watts, ISI marked, BEE 5 star rating including fixing on wall with chromium plated screws & nut bolts connected to existing water and electric connection complete all as specified and directed by the Engineer-in-charge. Make: Jaquar CAT Part No. INS-WHT-3KW03 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply, fixing, testing and commissioning of storage type water heater (geyser) vertical type of 25 Ltrs capacity, single phase, rust Resistant, ABS body stainless steel inner tank with thermal cut off with power consumption 2000 watts, ISI marked, BEE 5 star rating including fixing on wall with chromium plated screws & nut bolts connected to existing water and electric connection complete all as specified and directed by the Engineer-in-charge. Make: Jaquar CAT Part No. MET-WHT-PV0025 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing hot water extension pipe made out of copper chromium plated 450mm long with brass adaptor and fixing in position complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair 450mm long PVC connector with brass adaptor, washer and fixing in position complete all as specified and directed by the Engineer-in-charge.

Taking down old geyser of any capacity carefully alongwith hot and cold water pipe 450mm long and deposit in MES Storeyard for safe custody complete all as specified and directed by the Engineer-in-charge.

FIRE FIGHTING

Material & Labour for Sign board of size 300mm X 150mm reading 'EXIT' in 12.5mm block letters in green and white background, properly spaced to provide good legibility located directly in corridor near to each staircase and squarely attached to the wall or partition in a way that the top of the sign is not above 2 m from the finished floor level complete all as specified and directed by the Engineer-in-charge. Old U/S Board will be taken on credit.

Material & Labour for Sign board of size 150mm X 600mm, posted and maintained within each stair enclosure on every floor, indicating the 'Floor Number' in bold type and at 75mm high numerals in red and white background, securely attached to the stair side of the door in a way that the bottom of the sign is not above 1.5 m from the finished floor level complete all as specified and directed by the Engineer-in-charge. Old U/S Board will be taken on credit.

Material & Labour for Sign board of size 450mm X 150mm reading 'FIRE POINT' in 12.5 mm block letters in white and red background, properly spaced to provide good legibility located directly in corridor near to each Manual call point/Fire Extinguisher and squarely attached to the wall or partition in a way that the top of the sign is not above 2 m from the finished floor level complete all as specified and directed by the Engineer-in-charge. Old U/S Board will be taken on credit.

Material & Labour for Sign board of size 150mm X 600mm, posted and maintained at each lift landing and on the side of the stairway door from which egress is to be made on every floor, indicating the 'LIFT/STAIRCASES' by an alphabetical letter in bold type and at 75 mm high letters in red and white background, securely attached to the side of the stairway door from which egress is to be made in a way that the bottom of the sign is not above 1.5 m from the finished floor level complete all as specified and directed by the Engineer-in-charge. Old U/S Board will be taken on credit

Material & Labour for low smoke zero halogen (LS0H) flame retardant armoured type fire alarm control cable of size 1.5sqmm 2 core, conforming to BS 7629-1, BS 6387 & BS EN 50200 and rated for 500 V and having plain annealed stranded copper conductor with primary insulation of glass mica fire resistant tape and secondary insulation of high performance silicone rubber, earth/drain wire of annealed tinned copper, electrostatic screen of aluminium fire barrier and type LTS3 outer sheath conforming to BS 7655, suitable for operating temperature range -30 ˚C to +70 ˚C and minimum bending radius being 6 times the overall cable diametre, RED in colour, including laying, clamping, termination and ferruling complete all as specified and directed by the engineer-in-charge.

Material & Labour in repair for Yard hydrant/Stand Post type Fire Hydrant, conforming to IS 908:1975, consisting of one Class- I type sluice valves with cap, road surface boxes, a duck foot bend, flange riser and 80 mm NB CI flanged stand post column of 1.5 m height, perfectly water tight under hydraulic pressure along with coating and painting complete all as specified and directed by the engineer-in-charge.

Supply & Fixing in repair Outdoor type lockable hose cabinet of size 600 mm (H) x 800 mm (L) x 250 mm (D) suitable to house 2 Nos. of 15 m RRL hose and 2 Nos. of branch nozzles, made of 18 gauge MS sheet with double door with 4 mm thick glass and door frame made of 16 gauge MS sheet painted two coats of fire red outside and brilliant white inside over a coat of primer, including fixing on wall with nut and bolts of suitable size and numbers complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair Indoor type lockable hose cabinet of size 600 mm (H) x 800 mm (L) x 250 mm (D) suitable to house 2 Nos. of 15 m RRL hose and 2 Nos. of branch nozzles, made of 18 gauge MS sheet with double door with 4 mm thick glass and door frame made of 16 gauge MS sheet painted two coats of fire red outside and brilliant white inside over a coat of primer, including fixing on wall with nut and bolts of suitable size and numbers complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair gunmetal fire hydrant single headed landing valve with 50 mm NB flanged inlet, brass spindle controlled 63 mm NB female instantaneous outlet type gunmetal coupling, blank cap, chain, twist release type lug & all accessories conforming to IS 5290:1993 including fixing and flanged tapping from stand post type fire hydrant complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing of orifice plate made out of 6 mm thick SS 304 with orifice of required size to be fitted between flange and landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair non-percolating rubber reinforced lined RRL hose type- A 15 m long fire hose of 63 mm NB size, conforming to IS 636: 1988, rated for bursting pressure of 35.7 kg/cm² complete with gunmetal male & female coupling conforming to IS 903: 1993 complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair branch pipe, conforming to IS 903: 1993, having 63 mm NB instantaneous gunmetal inlet, made threaded outlet, 15 mm NB long nozzle, suitable for inter connection to hose pipe coupling complete all as specified and directed by the engineer-in-charge.

Supply & Fixing in repair swinging type 30 m long First Aid Hose Reel, conforming to IS:884-1969, having 19 mm NB thermoplastic reinforced hose reel tubing, conforming to IS 12585: 1988, 25 mm NB ball valve, stop cock, terminating with gunmetal coupling & nozzle of 6 mm NB outlet with shut-off valve, conforming to IS 8090: 1976 complete with MS socket for tap-off, red colour drum, brackets (including painting) for fixing on wall with anchor fastner, bolts, nuts, etc. complete all as specified and directed by the Engineer-in-charge.

Supplying, installing, testing and commissioning of MS air cushion tank, conforming to IS 4736:1968 on top of each riser fabricated from 6 mm thick MS plate, 200 mm in diametre and 1.2 m in height with dished ends fabricated from 8 mm thick MS plate with Air release valve with stop cock, flanged inlet connection and drain arrangement with 25 mm NB valve, pressure gauge with gun metal stop cock including taking down old and u/s air cushion tank complete all as specified and directed by the Engineer-in-charge.

Supply, installation, testing and commissioning of 4-way fire brigade inlet connection, conforming to IS 5290: 1993 with four 63 mm NB inbuilt gunmetal non-return valves, four 63 mm NB instanteneous couplings arranged on 100 mm NB pipe manifold and connected to fire hydrant ring main and fire hydrant wet riser pipe including taking down old and u/s complete all as specified and directed by the Engineer-in-charge.

Supply, installation, testing and commissioning of addressable Fire Alarm Control Panel (FACP) complying with BS EN 54 two loop panel of capacity from 99 detectors & 99 modules upto 200 detector and modules complete all as specified and directed by the Engineer-in-charge.

Supply, installation, testing and commissioning of FM approved and UL listed intelligent monitor module, with built-in type identification automatically identifying the device as addressable monitor module to the FCAP, to supervise a circuit of dry-contact input devices, viz. flow switch of sprinkler line, powered directly by two-wire SLC loop, high noise immunity, SEMS screws with clamping plates for ease of wiring, direct-dial entry of addresses, LED indicators, etc. complete all as specified and directed by the Engineer-in-charge.

Supply, installation, testing and commissioning of FM approved and UL listed addressable control module to provide FACP a circuit for notification appliances (e.g. Horns, Strobes, Horn Strobes, etc.) having built-in type identification, integral LED indicators, high noise immunity, SMES screws with clamping plates for wiring ease, direct-dial entry of address, etc. complete all as specified and directed by the Engineer-in-charge. (Power shutdown to all lifts other than Fire lifts in case of fire alarm).

Supply, installation, testing and commissioning of surface / semi- flush mounted Dual Action Manual Pull Station "Push In & Pull Down" including an addressable interface for the intelligent FACP having built-in bicolour LED which is visible, flashing in normal operation and latching steady red in alarm condition, captive screw terminals wire-ready for easy connection to SLC loop complete all as specified and directed by the engineer-in-charge. Make: Notifier NBG-12LX or or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply, installation, testing and commissioning of UL listed analogue addressable type Multisensor Detectors with heat & smoke combination with the fixed temperature of 59 degrees Centigrade and Dual LED indication for 360-degree visibility, milky white in color, shall be polarity insensitive, easy to install, advanced detection and communication protocol with insect filter chamber (in machine room & Metre room) complete all as specified and directed by the Engineer-in-charge. Old U/S detector will be taken on credit.

Supply, installation, testing and commissioning of addressable electronic sounder cum strobe complete all as specified and directed by the Engineer-in-charge. Old U/S hooters will be taken on credit.

Supply & Fixing sprinkler glass bulb type (standard response) Pendent type as per IS:15106/TAC guidelines 68 degree temperature rating pendent type complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair ISI marked MS ERW pipes with all accessories like all fittings including tees, elbows, reducers, union, flanges, rubber gaskets, GI nuts bolts, washer, including supporting/fixing the pipe on floor/wall/ceiling with clamps, hangers, angles, channels (using anchor fastners) with painting of one coat primer and 2 or more coats of synthetic enamel paint complete all as specified and directed by the Engineer-in-charge for following sizes:-

MS ERW pipes Heavy class of dia 150 mm

MS ERW pipes Heavy class of dia 100 mm

MS ERW pipes Heavy class of dia 50 mm

MS ERW pipes Heavy class of dia 32 mm

MS ERW pipes Heavy class of dia 25 mm

Supply & Fixing in repair Sluice Valve 150 mm dia, cast iron body, ISI marked, flanged ends of class PN - 1.6 with stainless steel spindle, hand wheel all as per IS 14846 - 2000 with all acessories and complete with including 2 Nos. flanged joints complete with jointing material such as 3 mm thick rubber gasket, nuts, bolts, washers complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair Sluice Valve 100 mm dia, cast iron body, ISI marked, flanged ends of class PN - 1.6 with stainless steel spindle, hand wheel all as per IS 14846 - 2000 with all acessories and complete with including 2 Nos flanged joints complete with jointing material such as 3 mm thick rubber gasket, nuts, bolts, washers complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair for PN 1.6 rated straight type Cast iron (CI) Swing Check type reflux (non return) valve of size 150mm dia conforming to IS 5312-1: 2004 having CI body, bolted cover, integral / renewable seat, renewable disc, gunmetal trim with rubber seat ring with flange drilling standard end connection conforming to IS 1538: 1993 and necessary accessories complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing for 32 mm NB compact 3 position ball valve with drain orifice (Test and Drain valve) to test and drain water flow through sprinkler systems having OFF-TEST-DRAIN position, along with necessary accessories complete all as specified and directed by the Engineer-in-charge. (3 valve per floor - One for sprinkler branch, one for drain pipe, one for test valve)

Supplying, installing, testing and commissioning of 32 mm NB universal type flow switch on sprinkler distribution header on each floor including connection to "Fire Alarm Control Panel" through cable complete as specified and directed by the Engineer-in-charge.

Supply & Fixing Sight glass for viewing water flow in 32 mm dia pipe including all fittings/accessories required complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair Cast Iron Air Valves with single air outlets, conforming to IS 14845 of size 100 mm dia bore (for riser) including all fittings/accessories required complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair Cast Iron Air Valves with single air outlets, conforming to IS 14845 of size 50 mm dia bore (for drain pipe) including all fittings/accessories required complete all as specified and directed by the Engineer-in-charge.

Supply, installation, testing and commissioning Fire Pump Diesel Engine Driven Horizontal End Suction, Centrifugal type conforming to IS - 12469 1988 with CI casing, bronze impeller and stainless steel shaft mounted on heavy duty bearings suitable for continuous operation with range of operation 0% to 150% of rated capacity for 440 V, 3 phase,50 Hz AC supply 90 m Head, 2280 LPM discharge complete all as specified and directed by the Engineer-in-charge.

[i] Suitable HP and RPM diesel engine, water cooled with radiator, conforming to IS 10002: 1981, complete with auto starting mechanism, 12/24 V electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour, etc. as required. [ii] MS fabricated common base-plate, coupling, coupling guard, foundation bolts, etc. complete with accessories as required. [iii] Suitable cement concrete foundation duly plastered with anti vibration pads.

Supply, installation, testing and commissioning of factory made, CPRI type tested, indoor, cubical compartmental type "Motor Control Center" (MCC) of suitable size, conforming to IEC 61641, having both sides openable with hinged double doors & locking arrangement and IP 54 protection made out of 2.00 mm thick mild steel CRCA sheet, supported and fixed on structural frame of angle iron of suitable size, including earthing stud, labelling, painting to all internal & external exposed steel surfaces with powder coating paint (7 tank process), duly fixed in ground with PCC foundation (1:2:4) type B1, with danger notice plate of 1.6 mm thick mild steel sheet, vitreous enamelled (white) with letters figures and conventional skull and bones in signal red colour, suitable for 3- Phase 4 Wire system, 500 V grade with necessary wiring, PVC sheathed stranded copper conductor of appropriate length & size, including fixing lugs, bolts, screws etc. ccomplete all as specified and as directed by Engineer-in-charge.

Supply & Fixing in repair for Pressure switch Universal type with suitable pressure range having die cast aluminium construction and SS sensing element with ball valve, fittings viz. unions, collars, reducers etc. in existing header for fire pumpsets, wiring up to Motor Control Centre complete all as specified and directed by the Engineer-in-charge.

Material & Labour for carrying out in situ alteration to the existing Fire fighting header and making one branch connection suitable for 150 mm pipe including cutting, welding, flange inserts, etc. and provision for installing one NRV of size upto 200 mm dia and isolating sprinkler header and wet riser/ yard hydrant header complete all as specified and as directed by Engineer-in-charge.

Material & Labour in repair for provision of priming arrangement with 20mm GI pipe medium - 15 RM, 20 mm gate valve-03 Nos complete to all three pumpsets from overhead tank complete all as specified and directed by the Engineer-in-charge.

Excavation in trenches not exceeding 1.5 m wide and 1.5 m depth for laying pipes etc. and getting out in hard/ dense soil complete all as specified and directed by the Engineer-in-charge.

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed by the Engineer-in-charge.

Returning, filling including spreading, leveling, watering, well ramming in layers complete all as specified and directed by the Engineer-in-charge.

Material & Labour for cutting of existing road upto 15 cm thickness and making good using Patchmate or any other techno-commercial equivalent instant road restoring material suitable for goods vehicle movement complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing in repair pressure gauge 4" dial 0-14 kgs rating complete all as specified and directed by the Engineer-in-charge.

Material & Labour for control wiring with 3 core 2.5 sqmm FRLS copper wire for PA system drawn in and including steel conduit fixed on wall/ceiling with clamps complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Amplifier of 250 Watt capacity complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Ceiling Speaker of 4 Watt capacity complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Microphone set suitable for making announcement complete all as specified and directed by the Engineer-in-charge.

INTERNAL ELECTRIC SUPPLY

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition sepertately) and making good disturbed surfaces of walls, floors etc. Note: Serviceable tube lights etc shall be kept under safe custody and refixed as directed.

Material & Labour for point wiring conforming to IS-732:1989 complete with 1.5 sqmm single core multistranded FRLS PVC insulated sheated copper conductor, 1100 volts grade conforming to IS-694:1990 drawn through and including PVC non-metallic concealed conduit ISI marked with accessories concealed in wall/floor including cutting chases, pining etc with modular metallic ISI marked terminal boxes, concealed in wall (PVC casing caping of suitable size shall be used where ever concealing is not possible) including one FRLS PVC insulated and sheathed multistanded green colour copper conductor 1.5 sqmm as earth continuity conductor connected to common earth as earth dolly for the following :- Note : - (i) Circuit conductor from MCB DB to Switch boards should not be less than 2.5sqmm. (ii) Modular metal flush box shall be paid seperately under relevant items of this schedule.

(a) One light point controlled by one switch SP one way.

(b) One ceiling fan point controlled with one 5A switch

(c) One exhaust fan point controlled with one 5A switch

(d) One 3 pin socket outlet 5 Amps on independant board.

(e) One 3 pin socket outlet 5 Amps on same board with other switches.

(g) One bell pont controlled by one bell push 5 Amps independent board.

Supply & Fixing modular switch, 6 Amps , One way, one module , ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681100 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing modular type bell push 6 amps 1 module, ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681109 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing modular switch, 16 Amps , One way, one module , ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681101 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing modular switch, 20 Amps , One way, one module , ISI marked complete all as specified and directed.

Supply & Fixing bell electric AC 230 Volts single pole ding dong with ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681146 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing modular socket, 6 Amps, 2/3 pin combined, two module, ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681124 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing modular socket, 16 Amps , 6 pin combined , two module , ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681122 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing modular TV Socket ISI marked including flush box and cover plate with frame complete all as specified and directed. Make:- Legrand CAT No. 681133 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Telephone Socket RJ 45, ISI marked complete including flush box & cover plate and frame as specified and directed. Make:- Legrand CAT No. 681132 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Rigid non-metallic PVC conduit of not less than 20 mm dia inclusive of boxes all tees, bends, elbows, reducers, bell mouth tube end and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc for provison of TV/Tele cable. Note: Conduit shall be concealed duly cutting grooves and making good all as directed.

Supply & Fixing ceiling rose surface bakelite with ISI mark, three terminals complete all as specified and directed.

Supply & Fixing Modular white cover plate with Frame 1 Module, ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681300 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular white cover plate with Frame 2 Module, ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681301 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular white cover plate with Frame 3 Module, ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681302 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular white cover plate with Frame 4 Module, ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681303 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular white cover plate with Frame 6 Module, ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681304 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular white cover plate with Frame 8 Module, ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681305 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular white cover plate with Frame 12 Module, ISI marked complete all as specified and directed. Make:- Legrand CAT No. 681308 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular metal flush box 1/2 module ISI marked and including cutting hole in wall / ceiling/piller etc and making good surface complete all as specified and directed. Make:- Legrand CAT No. 689060 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular metal flush box 3 module, ISI marked and including cutting hole in wall / ceiling/piller etc and making good surface complete all as specified and directed. Make:- Legrand CAT No. 689061 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular metal flush box 4 module, ISI marked and including cutting hole in wall / ceiling/piller etc and making good surface complete all as specified and directed. Make:- Legrand CAT No. 689062 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular metal flush box 6 module, ISI marked and including cutting hole in wall / ceiling/piller etc and making good surface complete all as specified and directed. Make:- Legrand CAT No. 689063 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular metal flush box 8 module, ISI marked and including cutting hole in wall / ceiling/piller etc and making good surface complete all as specified and directed. Make:- Legrand CAT No. 689065 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing Modular metal flush box 12 module, ISI marked and including cutting hole in wall / ceiling/piller etc and making good surface complete all as specified and directed. Make:- Legrand CAT No. 689067 or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing integrated LED batten 20 Watt, 4 feet long, full white in Engineering plastic battern with white acrylic cover with built in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5 sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Refixing only of LED T/L 18/20 Watt LED type after cleaning and minor servicing comlete all as specified and directed by the Engineer-in-charge. (Old serviceable T/L taken down under this Work will be used)

Supply & Fixing integrated LED batten 10 Watt, 2 feet long, full white in Engineering plastic battern with white acrylic cover with built in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5 sqmm from ceiling rose to connector of fitting including taking down existing unserviceable light fitting of any description complete all as specified and directed.

Supply & Fixing in Lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as directed by the Engineer-in-charge.

Taking down MCB DB of any type, single phase including disconnection of all circuits complete with MCBs etc.

Supply & Fixing MCB DB SPN 18 way suitable for single phase AC supply, 230 V sheet steel powder painted enclosure double door type with minimum IP-43 degree of protection with built in 200 Amps copper bus bar, neutral link and earth link complete including flush off in wall with cutting and making good the disturbed surface including connection of circuits with copper pin terminals complete all as specified and directed.

Supply & Fixing MCB DB SPN 4 way suitable for single phase AC supply, 230 V sheet steel powder painted enclosure double door type with minimum IP-43 degree of protection with built in 200 Amps copper bus bar, neutral link and earth link complete including flush off in wall with cutting and making good the disturbed surface including connection of circuits with copper pin terminals complete all as specified and directed.

Supply & Fixing MCB DB TPN 6 way suitable for single phase AC supply, 415 V sheet steel powder painted enclosure double door type with minimum IP-43 degree of protection with built in 200 Amps copper bus bar, neutral link and earth link complete including flush off in wall with cutting and making good the disturbed surface including connection of circuits with copper pin terminals complete all as specified and directed.

Supply & Fixing in repair ISI marked 63 Amp, 30mA, 230V, DP RCBO, conforming to IS:12640 (Part 2)-2016, having front face indication for earth leakage fault, sliding bottom clamp, colour coded on/off indication on dolly, biconnect IP20 protected lower terminals and sliding shutters, complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing MCB SPN upto 32 Amps, 240 Volts, C Series complete all as specified and directed.

Supply & Fixing MCB TPN upto 32 Amps, 240 Volts, C Series complete all as specified and directed.

Supply & Fixing MCB SP 6-32 Amps, 240 Volts, C Series complete all as specified and directed.

Taking down old unserviceable submain cable of any size and capacity and finishing wall surfaces.

Material & Labour submain wiring of XLPE insulated, PVC sheathed, aromoured cable, 1100 volts grade with copper conductor of 2 core 10 Sqmm laid in trenches/ through pipe ducts or fixed on wall etc. complete all connections to DBs all as specified and directed by the Engneer-in-charge Note: Earth wire of 1x10 sqmm shall be provided from copper strips at shaft to main DB of Qtrs and shall be measured and paid seperately.

Supply & Fixing copper strips of size 32mmx6mm thick for earth dolly provided at each floor In shaft having punched holes for each connections duly grounted on wall connected to main panel complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing Single Core 10 sqmm green colour copper conductor for earth wire for main shaft earthing strips to individual DBs complete including conduit of suitable size all as specified and directed by the Engineer-in-charge.

Supply & Fixing in replacement Plug and Socket enclosure, in sheet metal enclosure with MCB, SP 20 Amps 240 Volts complete with metal clad socket inlcuding flush off in wall with cutting and making good the disturbed surface for window type air conditioners/ geyser complete all as specified and directed by the Engineer-in-charge.

Taking down and Material & Labour for Earthing with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick, burried directely in ground (earth pit not less than 2.5 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised iron strip 32 x 6 mm with the help of bolts, nuts, check nuts and washers of galvanised iron or steel, protection GI pipe of 40 mm dia including necessary excavation, PCC 1:3:6 type D2 and PCC cover 1:2:4 type B1 watering arrangement with GI pipe funnel, jali, and cast iron cover fixed on top of pit complete all as specified and shown in electrical plate No.3 including connection to the earthing test point and testing on completion.

Taking down Ceiling/ Exhaust fan of any sized, sealing cable and dismantling blades carefully and removing fan and blades to MES Store for safe custody all as directed by the Engineer-in-charge.

Supply & Fixing ceiling fans complete with blades, down rods with safety GI wire connecting up to fan hook, electronic regulaor modular type and accessories, 230 volts, 1200 sweep. Minimum air delivery 210 CFM with service value 5.0 BEE. Five star rated with brushless direct current motor 26 W, minimum rated speed 350 RPM, service value 8.6, starting voltage 120 V maximum and connecting up including provision of flexible 3 core Copper Cable all as specified and directed by the Engineer-in-charge. Make:- Havells (CAT No FHCNF5SIVR48P) or any other techno-commercial equivalent model as mentioned in Particular Specifications.

Supply & Fixing exhaust fan, steel body AC single phase, 230 volt of size 300 mm sweep 1400 RPM 55 watt Air delivery 1250 cmh with blades, and frame and louvers complete with fixing arrangements on the wall with nuts and bolts making good surfaces all as specifed and directed by the Engineer-in-charge.

Making round/ square hole cutting in the kitchen wall with the help of cutting machine/chisel/hammer etc. for fixing of exhaust fan of size 250 mm to 300 mm & making good to the distrubed surface including plaster, distemper, white wash complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing of New LED building security light 45 Watt indus series powder coated pressure die cast aluminium high power LED building security light with heat resistant toughened glass with lens with IP66 Protection including 40 mm dia pipe bracket fixing on wall at any height with 02 nos of MS clamp of suitable size, complete all as specified and directed by the Engineer-in-charge.

Supply, fixing, installation, testing and commissioning of single phase auto clean wall mounted electric chimney, voltage 220V with touch control, black tempered glass, heat autoclean, control gesture & 3 touch control, 2 x 1.5 W led lamp, filterless and oil collector of stainless steel with top of size 600 mm along with minimum 1350 cum per hr suction power with rated capacity including all necessary fixtures and fittings complete all as specified and directed by the Engineer-in-charge. Make:- Faber Model - APEX Cat No - Apex FL HC BK 60/Glen/Kaff or any other techno-commercial equivalent.

Supply & Fixing aluminium flexible pipe for electric chimney exhaust of diametre 150mm, length 8.5 feet after expansion along with end cap/ cowl cover for exhaust pipe of suitable size including making round hole of diametre 200mm in any type of wall and inserting PVC pipe 200mm medium grade in round hole cutting portion only with packing including suitable size of clamps complete all as specified and directed by the Engineer-in-charge.

Supply, installation, testing and commissioning of LT Panel Metre cabin panel indoor type of minimum size 900 mm x 900 mm x 450 mm mounted on angle iron frame 40x40x5 mm grouted on floor, cubical indoor type for 415V, 3 phase, made of 2 mm thick CRCA sheet weather, vermin proof factory fabricated, CPRI approved, front open hinged door with locking arrangement powder coated, individual compartment for MCCBs and 400 Amps rated bus bar, top and bottom cable entry including disconnecting cable connections and electronic Metres/ smart prepaid metres from old Metre cabin panel and fixing/connecting in new insalled panel with provisions of thimble/lugs and necessary farmwork and PCC foundation 1:2:4 using 20 mm graded stone aggregates and making arrengement for fixing of panel and making good to disturbed surface as directed comprising of the following :-

(a) MCCB, FP, 250 Amps 36 kA- 01 Nos. (b) MCB SPN 63 Amps, 10KA, B series - 16 No . (c) Sheet metal enclosure 2 way without bus bar - 16 No, (d) Copper Bus bar, 400 Amps Rated - R,Y,B & N (e) Digital AmMetre-01 No (f) Digital VoltMetre-01 No (g) Phase indicator lamp R,Y & B (h) Making provision for fixing of digital electronic Metres removed from old panel including fixing and providing vision glasses - 16 Nos. (j) Material and labour for 2 core 10 Sqmm multistranded copper conductor cable 1100V form bus bar to electronic energy Metres using suitable size copper thimbles/glads.

Supply, laying, testing and commissioning XLPE insulated, PVC sheathed, armoured LT cable, 1100 Volts grade with aluminium conductor of size 3.5 core 95 Sqmm laid through pipe /ducts or fixed on wall etc complete all connections to LT panel with proper size glands & lugs from existing LT Panel to Lift Machine Room Panel, all as specified & directed by the Engineer-in-charge. (Including taking down old u/s cable)

Supply and installation of mini trunking of size 32mmx20mm with 1.5mm thickness with all finishing accessories (flexible cover, clip of partition, base joint internal angle, external angle, end cap, deviation, flat angle) conforming standard EN 50085-2-1. Trunking should accept wiring device with all the functions by associating the accessory of installation. Trunking should conform to the current specification of NF C 68-104 in term of both performance and level of function provide by the system. Installation trunking (which carries electrical/ signal/ telephone wiring accessories) should be type 3 (installation) in the new stranded material should be non flame propagating, degree of protection provided by encloser should be IP40 Protection against mechanical impact should be IK07. Trunking should be delivered in the length of 2 metres. The trunking cover and partition should be in PVC white RAL 9003. The accessories should be in plastic ABS white RAL. Note:- in case of Ceiling Self holding fastener of suitable size to be provided for trunking.

MUKESH CONSTRUCTION CO

SHREE KRISHNA INFRASTRUCTURE