Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹49.3 LAccepted-AOC KAJANIBARI DINJAN PO DINJAN DIST TINSUKIA ASSAM786189 | DINJAN | TINSUKIA | ASSAM | 786189 | L1 | Accepted-AOC LOWEST BIDDER | |
| 2 | L2₹51.6 L+₹2.1 L (4.33%)Rejected-Finance | L2 | Rejected-Finance OTHER THAN LOWEST | |
| 3 | L3₹52.0 L+₹2.6 L (5.23%)Rejected-Finance | L3 | Rejected-Finance OTHER THAN LOWEST | |
| 4 | L4₹52.5 L+₹3.1 L (6.28%)Rejected-Finance P O WEST SRIPURIA DIST TINSUKIA ASSAM PIN 786 145 | TINSUKIA | ASSAM | 786145 | L4 | Rejected-Finance OTHER THAN LOWEST | |
| 5 | L5₹52.5 L+₹3.1 L (6.29%)Rejected-Finance | L5 | Rejected-Finance OTHER THAN LOWEST |
Tender Value
₹49 L
EMD Value
₹98,000
Closing Date
24 May 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
COMMANDER WORKS ENGINEER, DINJAN
COMMANDER WORKS ENGINEER, DINJAN
REPAIRS AND MAINT OF ROAD AT LIKABALI, NLP, RAYANG AND ALONG MIL STN UNDER GE 872 EWS
2022_MES_522064_1
84089E8
Open Tender
Civil Works - Roads
Item Rate
180 days
GE 872 EWS
AS PER TENDER
7 documents required · 7 mandatory
₹500
Yes
GE 872 EWS
₹98,000
Yes
23 Jun 2022
5 May 2022
26 May 2022
5 May 2022
24 May 2022
19 May 2022
6 May 2022 - 18 May 2022
60 days
Amount
Preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and as directed.
Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area not exceeding 400 sqm, depth of pot hole exceeding 50 mm but not exceeding 100 mm including rolling over the broken surfaces using 8 to 10 tonnes power roller to required camber and gradient complete all as specified and as directed.
M & L except materials for 7.5 cm thick (compacted thickness) WBM, with coarse aggregates of granite, trap or basalt of grading 2 (63 to 45 mm size) or of grading 3 (53 to 22.4 mm size), spread, rolled and compacted to required gradient and camber with three wheel-power roller of 80 to 100 kN capacity or an equivalent vibratory roller complete all as specified and as directed.
M & L for 7.5 cm thick (compacted thickness) WBM, with coarse aggregates of granite, trap or basalt of grading 2 (63 to 45 mm size) or of grading 3 (53 to 22.4 mm size), spread, rolled and compacted to required gradient and camber with three wheel-power roller of 80 to 100 kN capacity or an equivalent vibratory roller complete all as specified and as directed.
M & L for applying evenly a priming coat with bituminous primer (paving grade bitumen VG-10 grade) @ 10 kg per 10 sq metres complete all as specified & as directed.
M & L for bituminous macadam not exceeding 75 mm thickness (compacted thickness) using hot mix plant and mechanical paver with 4% binder (paving grade bitumen VG-30 grade) content by weight of total mix, rolled and compacted with power roller 8 to 10 tonnes to required camber and gradient complete all as specified and as directed. Note :- (i) Bituminous macadam shall be laid using self propelled hydrostatic paver finisher and preparation of mix shall be using hot mix plant and transporting the mix in tipper. (ii) The exact bitumen content required shall be determined as per IRC 27: 2009. The adjustment in rate on MINUS side variation in quantity of bitumen if any shall be priced at the rate of ₹55 per kg. No claim whatsoever shall be made for adjustment in plus side.
Repair to potholes any depth, exe 30 mm and not exceeding 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc., cutting around edges to at least 25 mm in depth, making good by applying tack coat at the rate of 05 kg per 10 Sqm, putting in bituminous macadam well rammed and sealed with bitumen 9.8 kg per 10 sqm blinded with 0.09 cum stone chippings, 6.3 mm size and rolled and compacted with power roller 8 to 10 tonnes to required camber and gradient complete all as specified and as directed.
M & L for applying evenly a tack coat with bituminous primer (paving grade bitumen VG-10 grade) @ 5 kg per 10 sq metres complete all as specified & as directed.
M & L for bituminous concrete 40 mm (compacted thickness) using graded crushed stone aggregate premixed with binder (paving grade bitumen VG-30 grade) @ 5.5% by weight of total mix & hydraulic lime filler, rolled and compacted to required camber and gradient complete all as specified and as directed. Note :- (i) Semi dense bituminous concrete shall be laid using self propelled hydrostatic paver finisher and preparation of mix shall be using hot mix plant and transporting the mix in tipper. (ii) The exact bitumen content required shall be determined following the Marshall Mix Design procedure contained in the Asphalt Institute Manual MS-2 (Sixth Edition) as referred in case 3.5.3 of IRC 111: 2009. The adjustment in rate on MINUS side variation in quantity of bitumen if any shall be priced at the rate of ₹55 per kg. No claim whatsoever shall be made for adjustment in plus side.
Providing and applying 2.5 mm thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T & P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete all as specified and as directed.
S & F solar road studs of size not less than 100 mm X 100 mm X 10 mm made of weather resistance aluminium alloy and poly carbonate material electronically welded micro- prismatic lens with abrasion resistant coating as approved by the Engineer in charge. The cats eye shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35⁰ ± 5⁰ to base. The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM E: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge. The solar panel shall be high efficiency mono crystalline 2.5 V/60 m A and the battery shall be one Ni-mh type (1.2 V/1200 m Ah) high temp for backup of 36 hours full charging. The flash frequency shall be 60 ± 5 times per minute.
Providing and fixing Glow studs (cat's eye) of size 80 to 100 mm X 100 to 120 mm X 15 to 20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The cats eye shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35⁰ ± 5⁰ to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.
S & F metal tubular delineator 750 mm long X 40 mm dia MS pipe (medium grade) powder coated with thrice colour reflective tape strips (06 nos)of width 50 mm embedded 200 mm below ground level including excavation and PCC M15(Nominal Mix) with using 20 mm graded stone aggregate in foundation of size 200 mm X 200 mm X 200 mm and making good surface complete as per direction of Engineer-in-charge.
S & F road convex mirrors outdoor type made of one piece polycarbonate of size 80 cms including fixing with mounting pole and necessary foundations and filling with M-15 type B-1 20 mm aggregates, complete all as specified and as directed.
Repair to potholes any depth, not exceeding 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc., cutting around edges to at least 25 mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal), rolled and compacted with power roller 8 to 10 tonnes to required gradient and camber complete all as specified and as directed.
M & L for bituminous premixed carpet, 40 mm consolidated thickness with 0.54 cum of stone chippings mixed with 29.2 kg of binder (using paving bitumen VG30 grade), rolled and compacted to required camber and gradient with 8 to 12 tonne power roller, complete all as specified and as directed.
M & L for liquid seal coat, applying evenly binder (using paving bitumen VG30 grade) @ 9.8 kg per 10 Sqm binding with 6.3 mm size stone chippings @ 0.09 cum per 10 sqm and rolled to a uniform smooth surface with 8 to 12 tonne power roller complete all as specified and as directed.
S & F solar road studs of size not less than 125X 125 X 25 mm made of weather resistance aluminium alloy and poly carbonate material electronically welded micro- prismatic lens with abrasion resistant coating as approved by the Engineer in charge. The cats eye shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35⁰ ± 5⁰ to base. The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM E: 809 as recommended in BS: 873 part 4 :1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge. The solar panel shall be high efficiency mono crystalline 2.5 V/60 m A and the battery shall be one Ni-mh type (1.2 V/1200 m Ah) high temp for backup of 36 hours full charging. The flash frequency shall be 60 ± 5 times per minute. Make- Model no 111 JUGNU of Dark Eye or equivalent makes as given in Appx B
M/S AUTOMOTIVE WORLD
FREEZCON
M/S BORAH BROTHERS
boruah construction
MAZUMDAR ENTERPRISE
STANDARD ELECTRIC WINDERS
M H KHAN
Kaushik Enterprises
stage.html
html • 0.06 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .