Addition/ alteration, repair/ renovation of office and staff room at Govt. College for Women Udhampur.

Amount

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (Not exceeding 1.5 mtr in width & for shafts, wells, cesspits & the like not exceeding 10 sqm on plan, depth upto 1.5 m including disposal of excavated earth upto 1 mtr from cutting edge, disposed earth is to be levelled & neatly dressed.

Providing & laying in position cement concrete of specified grade excluding the cost of centering and shuttering -- All work upto plinth level 1:5:10 (1 cement :5 coarse sand : 10 graded stone aggregate 40 mm nominal size) Crushed.incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Providing and laying in position of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) excluding the cost of centering, shuttering, finishing and reinforcement. All work upto plinth level. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Providing & laying in position cement concrete of specified grade excluding the cost of centering and shuttering -- All work upto plinth level 1:3:6 (1 cement : 3 coarse sand : 6 graded stone agg. 20 mm nominal size) crushed with 20% plum incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Providing and laying in position cement concrete of 1:3:6 grade (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20mm nominal size) excluding the cost of centering and shuttering. All work upto plinth level. incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Brick work with common burnt clay F.P.S (non- modular) bricks of class designation 75 in foundation and plinths in cement mortar 1:6 (1cement : 6 fine sand). incl all carriage lead, lift, loading/ unloading/handing/ rehanding Complete

Half Brick masonry with bricks of class designation 75 in foundation and plinth in cement mortar 1 : 4 (1 cement : 4 coarse sand)incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Extra for brick works in super structure above plinth level up to floor five level.incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Extra for half brick masonry in superstructure above plinth level up to floor V level.incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Providing and laying Reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) in suspended floors, balconies, landings and staircases having 15 degree slope. upto floor five level excluding the cost of centering and shuttering.incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars.

Centering and shuttering including strutting, propping etc. and removal of form work for :-

Foundations, footings, bases of columns.

Suspended floors, roofs, landings, balconies and access platforms.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Edges of slabs and breaks in floors and walls upto 20cm wide.

Retaining walls, return walls, wall (any thickness) including attached pilasters, buttresses, plinth and string courses fillets etc.

Weather shade, chajjas, corbels etc. including edges.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, lead upto 50Mt & lift upto 1.50M.

Supplying and filling in plinth with fine sand under floors including, watering, ramming consolidating and dressing complete.incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

6mm thick cement plaster to ceiling of mix 1:3 (1 cement : 3 fine sand).incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

12mm cement plaster of mix 1:6 (1 cement : 6 fine sand).incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

15mm cement plaster on the rough side of single or half brick wall of mix in 1:6 (1 cement : 6 fine sand). incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand). incl all carriage lead, lift, loading/ unloading/handing/ rehanding Complete

15mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement : 4 fine sand).incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Providing & fixing 16 mm thick Granite of any colour and shape gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen plate form , vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement :4 coarse sand) with joints treated with white cement mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels.

Providing & fixing ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming of IS: 13755 of NITCO, ORIENT, SOMANY , KAJARIA or equivalent make in colour such as White Ivory , Grey, Fume red brown laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) incl. pointing the joints with white cement & matching pigment etc. complete.

Providing & laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS :15622 of approved make in all colours and shades , laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete ; Size of tile 80x80 cm

Providing & laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS :15622 of approved make in all colours and shades , laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete ; Size of tile 100x100 cm

Providing and fixing 1st quality ceramic glazed tiles conforming to IS: 13753 of minimum thickness 5 mm of approved make like NITCO, ORIENT, SOMANY, KAJARIA, or equivalent make in all colour , shades except burgundy, bottle green, black of any size as approved by Engineer In Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 Kg per Sqm. Incl. pointing in white cement mixed with pigment of matching shade complete.

Extra for providing edge moulding to 18mm thick Granite stone counters, Vanities etc. over item No. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone agg. 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed and consolidated & grouted with fine sand including finishing the top smooth. (Crushed).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z-section and other sections of approved make conforming to IS 733 and IS 1285, fixed with dash fastener of required dia and size incl. necessary filling upto gaps at junctions i.e at top, bottom and sides with required EPDM rubber/ neoprane gasket felt etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required incl. cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless steel screws, all complete as per architectural drawing and the directions of Engineer-in-charge (glazing ,panelling and dash fasterner to be paid for reparately). For fixed portion Anodised alumnium (anodised transparent or dyed to required shade according to IS:1868 minimum anodic coating of grade AC 15).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z-section and other sections of approved make conforming to IS 733 and IS 1285, fixed with dash fastener of required dia and size incl. necessary filling upto gaps at junctions i.e at top, bottom and sides with required EPDM rubber/ neoprane gasket felt etc. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required incl. cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless steel screws, all complete as per architectural drawing and the directions of Engineer-in-charge (glazing ,panelling and dash fasterner to be paid for reparately). For fixed portion For shutters of doors, windows & ventilators incl. providing and fixing hinges /pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprane gasket required (fittings shall be paid for separately). Anodised aluminium (anodised transparent or dyed to required shade according to IS 1868 minimum anodic coating of grade AC 15).

Providing and fixing glazing in aluminium door, windows, ventilator shutter and partitions etc with EPDM rubber / neoprene gasket etc complete as per the architectural drawing and directions of Engineer-in-charge (Cost of aluminium snap beading shall be paid in basic items with floating glass panes of 5.50 mm thickness (weight not less then 13.50 kg/Sqm.)

Providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to IS: 1868 minimum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existing windows frame with C.P brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of engineer- in- charge (only weight of grill to be measured for payment).

Proving & fixing 35 mm thick wire gauze shutters using galvanised M.S wire gauze of average width for aperture 1.4 mm both direction with wire of dia. 0.63mm for doors, windows & clerestory windows with hinges & necessary screws. Second class deodar wood.

Filling the gap in between aluminium frame and adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rodf of approved quality as per architectural drawings and direction of Engineer- In - Chatge complete upto 5 mm depth and 5 mm width

Providing dash fastners for fixing of aluminium frame in the existing opening incl. c/o gathies

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked having brand logo embossed on the body/ plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and coer plates with brass pivot and single piece MS sheet outer box with slide plate etc. complete as per the direction of engineer- in- chartge with brass cover polate minimum 1.25 mm thickness

Providing and fixing 100 mm brass locks (best make of approved) quality for aluminium doors incl. necessary cutting and making good etc. complete

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of engineer in charge anodized (AC 15) Aluminium

Providing and fixing aluminium handles ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. 125 mm

Providing & fixing aluminium tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete.

Providing & fixing aluminium sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts & screws etc. complete. 250x16 mm dia

Providing & fixing aluminium hanging floor door stopper ISI marked anodized (anodic coating not less than grade AC-10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete Twin rubber stopper.

Providing and fixing aluminium casement stays ISI marked anodised (anodic coating not less than grade AC 10 as per ISI: 1868) transport or dyed to required colour or shade with necessary screws etc. complete.

Providing & fixing on wall face unplasticised- Rigid P.V.C rain water pipe confirming to I.S – 13592 type –A incl. jointing with seal ring confirming to I.S- 5382 leaving 10 mm gap for thermal expansion 110 mm dia

Providing and fixing on wall face unplasticised-PVC moulded fitting / accessories for unplasticised- rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion :-

Coupler 110mm.

Single tee with door 110 x 110 x 110mm.

Bend 87.5* 110mm.

Providing & fixing on wall face unplasticised-PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes confirming to IS:13592 type A including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion clips 110 mm dia

Providing and fixing to the inlet mouth of rain water pipe PTMT (an engerring thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms

10 cm thick (average) mud phuska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa at 35kg per cum of earth and gobri leaping with bhusa at 35kg per cum of earth and gobri leaping with mix 1:1 ( 1 clay: 1 cow dung) and covered with flat tile bricks of class designation 1 00 grouted with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finishing neat.

Painting top of roofs with bitumen of approved quality at 17 kg per 10 Sqm impregnated with a cost of coarse sand at 60 Cu dm per 10 Sqm including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete. With residual type petroleum bitumen of penetration 80/100. incl. all carriage lead, lift, loading/ unloading/handing/ rehanding Complete

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design: In 75x75 mm deep chase.

Providing and fixing plastic sheet of superior quality on roof after painting the roof with bitumen

Providing & laying cement concrete in retaining walls, return walls, Walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or laces, courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets etc. upto floor 5- level, excluding the cost of centering, shuttering & finishing. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agg. 20 mm nominal size) crushed. incl all carriage lead, lift, loading/ unloading/handing/ rehanding Complete

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and applying white cement based putty of average thickness 1mm of approvded brand and manufacture over the plastered wall surfaces to prepare the surafce even and smooth complete.

Distempering with oil bound washable distemper of Approved brand & manufacture to give an even shade over and including priming coat with cement primer. New work (two or more coats) over and including priming coat with cement primer

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Wall pinting with plastic emulsion paint of approved brand and manufacture to give an even shade one or more coats on old work

Applying one coat of water thinable cement primer of approved brand & manufacture of wall surface water thinable cement primer.

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens repair to edges plaster panels and finishing the groove complete as per specifications and direction of the Engineer in charge.

Providing & fixing white vitreous China pedestal type water closet (Europen Type) with cistern (A/PHAS-100+Cat No. 21054) with CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with rubber lip/ buffer and side gap filled with silicon sealant wherever required. including brass/ SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of engineer in charge

Providing & fixing of white vitreous china wash basin with pedestal (Hindware Cat No. 1008+ Pedestal Cat No. 11003) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaguar Cat No. 769B+Parko 1535 or approve equivalent), 450 mm long CP Copper connecting pipes (Jaguar Cat No. 803B or Parko 1535 or approved equivelent) wall flanges and rubber adopters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer- in- charge.

Providing & fixing CP single liver extended basin mixer (Height 85 mm) without popup waste system with 450 mm long braided hoses and brass trap with all fittings and accessories as per direction of engineer in charge (Jaguar FUS 29023B)

Providing & fixing white viterous china flat back half stall urinal basin of 580x380x350 mm with flat white PVC automatic flushing cistern, of approved make with fittings, CI/ MS brackets, standard size of CP brass flush pipe, spreaders with unions and clamps complete, (all in CP brass) with waste fitting as per IS: 2556, CI trap with outlet grating and other couplings in CP brass including painting of fittings and brackets, cutting and making good the walls and floors wherever required single half stall urinal with 5 litre white PVC automatic flushing cistern of approved quality

Providing and fixing Salem Stainless Steel AISI 304 (18/8) kitchen sink as per I.S:13983 with C.I brackets and stainless steel plug 40mm including painting of fittings and brackets cutting and making good the walls wherever required 610x460mm bowl depth 200mm

Providing & fixing CP brass angle valve for basin mixer and geyser points of approved quality conforming to IS : 8931 a) 15 mm nominal size (Make Jaguar FUS 29053).

Providing & fixing of Soap Dish Holder with all fittings as per direction of engineer in charge (Jaguar Cat No. ACN 113N).

providing & fixing brass towel ring square with round flenge of approved make complete with all fittings (Jaguar Cat No. ACN 11021 BN)

Providing & fixing toilet holder with all fittings Jaguar Contienal ACN 1153 N.

Providng & fixing 15 mm dia CP brass bib cock with wall flange of approved quality conforming to IS standard (Jaguar Cat NO. 29037)

Providing & fixing 15 mm dia CP brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 grams (Jaguar Cat No. CON-107 KN).

Providing & fixing regular body of concealed stop cock suitable for 15 mm pipe line with protection cap (Jaguar ALD-083) with exposed part angular stop cock with flange FUS 29.53

Providing & fixing G.I. pipes complete with G.I fittings and clamps, including cutting and making good the walls etc. Internal work-Exposed on wall 20 mm dia nominal bore (Medium)

Concealed pipe including painting with anti-corrosive bitumastic paint, cutting chases and amking good the wall.

15mm dia nominal bore.

20mm dia nominal bore.

Providing & fixing G.I pipes complete with G.I fittings including trenching & refilling etc. (external work) 20 mm dia nominal bore

Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing Tee, including cutting and threading the pepe etc. complete 25 to 40 mm nominal bore

Providing, laying and fixing PVC pipes 100 mm dia for waste water and PVC's (Prince make) incl. encasing with cement concrete 1:4:8 (1 cement: 4 coarse sand: 8 graded stone agg. 20 mm nominal size)

Providing and fixing of PVC bends of 87.5 degree 110 mm dia (Prince make) for PVC waste pipes etc.

Providing and fixing PVC floor traps and setting in floor with cement mortar to match with floor finish- 100 mm dia ISI maked (Prince make)

Providing and fixing steel gratings 100 mm dia

Construction brick measonery man hole in cement motor 1:4 (1 cement: 4 Coarse Sand) R.C.C top slab with 1:2:4 mix (1 cement: 2 Coarse Sand: 4 graded stone aggrigate 20 mm nominal size) foundation concrete aggrigate 40 mm Nominal Size, in side palstering 12mm thick with cement mortor 1:3 (1 cement:3 Coarse sand) finshed with floating coat near cement and making channels in cement concrete 1:2:4 (1 cement:2 Coarse snad:4 graded stone aggirgate 20mm nominal size) finished with floating coat of neat cement complete as per standard design. inside size 90cmx80cm and 45cm deep including cast iron cover with frame (light duty) 455x610mm internal dimensionals. total wt. of cover and frame to be not less than 38kg (wt. of cover 33kg and wt.of frame 15kg) with F.P.S bricks of class designation 75 (crush stone aggrigate)

Making soak pit 2.5 m diameter 3.0 m deep with 45x45 cm dry brick honey comb shaft with bricks of class designation 75 mm and S.W drain pipe 100 mm diameter, 1.8 m long complete as per standard design. with F.P.S bricks.

Providing & placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and the base support for tank (Sintex, Electroplaste Star, Lotous or equivalent having valid ISI License). (1000 ltr capacity)

Supply assembly, errection, testing and commisssioning of pumping system comprising the following vertical/ horizontal centrifugal pumps (1 working+ 1 stand by) with mechanical seal, SS volute casing and SS impeller connected to suitable capacity TEFC induction motor suitable for 415+10% volts, 3 phase, 50 cycles AC supply with 100 mm dia pressure gauges including MS skid and mounting of the pumps on the skid (Motor to be of the same make as the pump) pump capcaity 180 lpm, at 30 m head (1 working+1 stand by) (Domestic water relift pump)

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 mtr lead of area of 3 Sqm anbd below

Dismantling doors, windows and clerestory windows (Steel or wood) shutter including chowkhats, architrave, hold fasts etc. Complete and stacking within 50 mtrs. Lead of area of 3 Sqm. and below

Reinforced cement concrete work in walls, (any thickness) including attached pilasters, buttresses, plinth & string courses, fillets, columns pillars, piers, abutments, posts and struts, etc. upto floor 5 – level , excluding the cost of centering , shuttering , finishing and reinforcement. 1:1 ½ :3 (1 cement : 1 ½ coarse sand : 3 graded crushed stone aggregate 20 mm nominal size) incl all carriage lead, lift, loading/ unloading/handing/ rehanding Complete

Cement concrete flooring 1:2:4 finished with a floating coat of neat cement including cement slurry, but excluding the coat of nosing of steps etc. complete 50mm thick with 20mm nominal size of stone aggregate.incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

12 mm cement plaster finished with a floating coat of neat cement of mix 1:3 (1 cement: 3 fine sand)incl all carriage lead, lift, loading/ unloading/handling/ rehandling Complete

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 mtr lead.

Demolishing cement concrete manually/ by mechanical means including disposal of material. 1:3:6 or richer mix

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster incl. disposal of rubbish to the dumping ground with in 50 mtr. Lead.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately) 2nd class Deodar wood.

Providing & fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S pressed Butt hinges bright finished off required size with necessary screws excluding panelling which will be paid for separately, all complete as per direction of engineer- in charge. Second class Deodar wood. 35 mm thick.

Removing dry or oil bound distemper, water proofing cement paint and the like by scraping and sand papering and preparing the surface smooth including necessary repairs to scratches etc complete.

Finishing walls with water proofing cement paint of required shade old work (one or more coat) applied @2.20 kg/ 10 sqm ovewr priming coat of primer applied @0.80 ltr/ 10 sqm complete including cost of priming coat

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade one or more coats on old work.

Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

M/s JINDAL BUILDERS

SANJEEV SINGH