REPAIR MAINTENANCE TO PUMP SETS LT PANEL BOARDS STARTERS AND CONNECTED ITEMS AT CPH ANPH JD AND DHANUSH PUMP HOUSE AREA AND REPAIR REPLACEMENT OF SUCTION DISCHARGE LINES CONTROL VALVES PRV AND OTHER CONNECTED WORKS AT CPH ANPH AND DHANUSH PUM

Amount

M& L for Disconnecting centrifugal pump from motor, suction and delivery pipe line of any Make, model and taking down packing for removing and insertion of new shaft sleeves or remove Bearing using bearing puller gear and fix new all two bearings and greasing all parts, coupling pump to motor and check for proper shaft alignments such that no vibration produce during opertion of following capacity pumps, complete all as specfied and as directed by Engineer-in-charge.

Bearings suitable for Pump coupled with 150 HP motor

Bearings suitable for Pump coupled with 100 HP motor

Bearings suitable for Pump coupled with 75 HP motor

Bearings suitable for Pump coupled with 60 HP motor

Bearings suitable for Pump coupled with 40/50 HP motor

M& L for Disconnecting motor from pump of any Make, model and remove Bearing using bearing puller gear and fix new all two bearings at DE /NDE including necessary greasing ,check for proper shaft alignments such that no vibratiobn produce during opertion of following capacity Motors.

Bearings suitable for Pump coupled with 150 HP motor

Bearings suitable for Pump coupled with 100 HP motor

Bearings suitable for Pump coupled with 75 HP motor

Bearings suitable for Pump coupled with 60 HP motor

Bearings suitable for Pump coupled with 40/50 HP motor

S&F in repair AC-3 type contactor with control voltage of 415V AC, 50 Hz with integrated auxillary or Add on block contacts with 1 or 2 NO and NC including connection of control wiring to contactor and testing of starter after repairing .

Contactor rating of 225A

Contactor rating of 130A

Contactor rating of 115A

Contactor rating of 85A

Contactor rating of 65A

S&F in repair Thermal over load relay with adjustable setting with integrated auxillary or Add on block contacts with 1 or 2 NO and NC including connection of control wiring to OLR and testing of starter after repairing .

OLR of capacity I Min of 135 to I max 225A

OLR of capacity I Min of 78 to I max 130A

OLR of capacity I Min of 69 to I max 115A

OLR of capacity I Min of 52 to I max 75A

OLR of capacity I Min of 45 to I max 65A

S&F self lubricated asbestoes non metallic and non graphite gland packing white colour of sizes 8 to 12 mm complete all as specified and directed. Make: Champion or equivalent

M&L for replacement of MS jaw coupling type-L with spider made of synthetic rubber or gear coupled type of suitable for 150 HP motor

M&L for replacement of MS jaw coupling type-L with spider made of synthetic rubber or gear coupled type of suitable for 100 HP motor

M&L for replacement of MS jaw coupling type-L with spider made of synthetic rubber or gear coupled type of suitable for 75 HP motor

M&L for replacement of MS jaw coupling type-L with spider made of synthetic rubber or gear coupled type of suitable for 60 HP motor

M&L for replacement of MS jaw coupling type-L with spider made of synthetic rubber or gear coupled type of suitable for 50/40 HP motor

Supply and fixing in repairs MS pipe heavy grade, ISI marked for suction and delivery for pump including necessary fitting including welding, painting with red oxide primer and providing necessary PCC support, all as specfied and directed by Engineer-in-charge of following sizes :-

300 mm dia

250 mm dia

200mm dia

150mm dia

100 mm dia

80 mm dia

Supply and fix in repairs CI foot valve flanged end IS 4038 PN 0.2 housing complete including replacement of nut bolts, cutting of pipe, welding complete all as specified and directed.

300 mm bore

200 mm bore

150 mm bore

100 mm bore

M&L for Disconnecting motor power cables of various sizes from electrical motor of different capacities and decoupling from the pump sets,removing and taking down carefully and transporting to authorised workshop ,Dismantaling stator and rotor carefully and rewinding stator assembly with supper enamelled copper winding wire of suitable gauge matching to existing gauge and cleaning of slots ,core with carbon tetra chloride solution and apply two coats of insulation varnish and keep stator assembly in heating chamber to improve insulation strength ,reassemble motor completey and transporation to site ,coupling pump to motor and check for proper shaft alignments such that no vibratiobn produce during opertioncoupling to pump with exact allinment ,connect power cables to motor and testing of following capacity motor

S & F in repair pressure gauge 150mm dia range 0-10Kg /Sqcm. Note: quoted rated should including for providing of adopter /Ferrule/check nut etc required for fixing pressure guage and necessary alterations including necessary welding to MS or CI pipe for taping if required.

Supply and laying in replacement of copper unamoured power cable of size 25 sqmm single core from motor starter panel to motor in HDPE pipe in ground including copper lugs, nut bolts and washers as reqd at site complete all as specified and directed.

Supply and laying in replacement of copper unamoured power cable of size 35 sqmm single core from motor starter panel to motor in HDPE pipe in ground including copper lugs, nut bolts and washers as reqd at site complete all as specified and directed.

Supply and laying in replacement of copper unamoured power cable of size 50 sqmm single core from motor starter panel to motor in HDPE pipe in ground including copper lugs, nut bolts and washers as reqd at site complete all as specified and directed.

Supply ,install, test and commissioning in replacement of LT Panel board from CPRI approved panel manufacturer made out of of 2mm CRCA sheet cubical totally enclosed with frame made out of 50mm x 50mm x 6mm angle iron door front and back openable with locking arrangement indoor type vermin and weather proof floor mounting type, suitable for 3 phase 4 wire,50 HZ , 415 Volt AC supply with 600A capacity copper bus bar (4 Nos) All MCCB shall be connected with suitable size of copper strip from main bus & with terminate point and complete wiring of panel board with suitable size PVC insulated multistranded copper conductor including lugs/thimbles etc with suitable Cable alley for provn of cable entries at bottom with cable glands including the following :- (a) MCCB 4 pole, 415V,400Amps 50 KA - 01 No (incoming) thermo magnetic adjustable release type,ICS=ICU=100% Make :L&T/ABB/Siemens/legrand (b) MCCB 3 pole,415V,250mps 50 KA - 03 Nos (outgoing) thermo magnetic adjustable release type,ICS=ICU=100% Make L&T/ABB/Siemens/legrand (c) Automatic star/Delta starters panel with all accessories mounting suitable for 75 HP-03 Nos. Make :L&T/ABB (d) Phase indicating lamps(RYB)-04 set (e) Digital panel meter for Amp,Volt,KWH, power factor and other parameter flush mounting of size 96X96mm-04 set. Make: Dip/AE/IMP (f) Suitable CTs for main and for 03 starter panels.

Supply ,install, test and commissioning in replacement of LT Panel board from CPRI approved panel manufacturer made out of of 2mm CRCA sheet cubical totally enclosed with frame made out of 50mm x 50mm x 6mm angle iron door front and back openable with locking arrangement indoor type vermin and weather proof floor mounting type, suitable for 3 phase 4 wire,50 HZ , 415 Volt AC supply with 800A capacity copper bus bar (4 Nos) All MCCB shall be connected with suitable size of copper strip from main bus & with terminate point and complete wiring of panel board with suitable size PVC insulated multistranded copper conductor including lugs/thimbles etc with suitable Cable alley for provn of cable entries at bottom with cable glands including the following :- (a) MCCB 4 pole, 415V,630Amps 50 KA - 01 No (incoming) thermo magnetic adjustable release type,ICS=ICU=100% Make :L&T/ABB/Siemens/legrand (b) MCCB 4 pole,415V,630Amps 50 KA - 01No (outgoing) thermo magnetic adjustable release type,ICS=ICU=100% Make L&T/ABB/Siemens/legrand (c) MCCB 4 pole,415V,100Amps 16 KA - 02Nos (outgoing) thermo magnetic adjustable release type,ICS=ICU=100% Make L&T/ABB/Siemens/legrand (d) MCB 4 pole , 63 Amps, 10 KA, 'C' Series -03 Nos (e) Phase indicating lamps(RYB)-04 set (f) Digital panel meter for Amp,Volt,KWH, power factor and other parameter flush mounting of size 96X96mm-01 set. Make: Dip/AE/IMP

Supply ,install, test and commissioning in replacement of LT Panel board from CPRI approved panel manufacturer made out of of 2mm CRCA sheet cubical totally enclosed with frame made out of 50mm x 50mm x 6mm angle iron door front and back openable with locking arrangement indoor type vermin and weather proof floor mounting type, suitable for 3 phase 4 wire,50 HZ , 415 Volt AC supply with 800A capacity copper bus bar (4 Nos) All MCCB shall be connected with suitable size of copper strip from main bus & with terminate point and complete wiring of panel board with suitable size PVC insulated multistranded copper conductor including lugs/thimbles etc suitable Cable alley with for provn of cable entries at bottom with cable glands including the following :- (a) MCCB 4 pole, 415V,630Amps 50 KA - 02 Nos (incoming) thermo magnetic adjustable release type,ICS=ICU=100% Make :L&T/ABB/Siemens/legrand (b) On load change over switch 630 Amps, 4 pole, 415 volts-01 No. Make L&T/ABB/Havells/Standard (c) MCCB 4 pole, 415V,400Amps 50 KA - 03 Nos (Out going) thermo magnetic adjustable release type,ICS=ICU=100% Make :L&T/ABB/Siemens/legrand (d) Phase indicating lamps(RYB)-04 set (e) Digital panel meter for Amp,Volt,KWH, power factor and other parameter flush mounting of size 96X96mm-01 set. Make: Dip/AE/IMP

Supply ,install, test and commissioning in replacement of LT Panel board from CPRI approved panel manufacturer made out of of 2mm CRCA sheet cubical totally enclosed with frame made out of 50mm x 50mm x 6mm angle iron door front and back openable with locking arrangement indoor type vermin and weather proof floor mounting type, suitable for 3 phase 4 wire,50 HZ , 415 Volt AC supply with 300A capacity copper bus bar (4 Nos) All MCCB shall be connected with suitable size of copper strip from main bus & with terminate point and complete wiring of panel board with suitable size PVC insulated multistranded copper conductor including lugs/thimbles etc suitable Cable alley with for provn of cable entries at bottom with cable glands including the following :- (a) MCCB 4 pole, 415V,160Amps 36 KA - 01 No (incoming) thermo magnetic adjustable release type,ICS=ICU=100% Make :L&T/ABB/Siemens/legrand (b) MCCB 3 pole,415V,63 Amps, 36 KA - 03 Nos (outgoing) thermo magnetic adjustable release type,ICS=ICU=100% Make L&T/ABB/Siemens/legrand (c) Automatic star/Delta starters panel with all accessories mounting suitable for 20 HP-03 Nos.Make :L&T/ABB (d) Phase indicating lamps(RYB)-04 set (e) Digital panel meter for Amp,Volt,KWH, power factor and other parameter flush mounting of size 96X96mm-04 set. Make: Dip/AE/IMP (f) Suitable CTs for main and for 03 starter panels.

Taking down old unserviceable panel boards of any capacity and disconnecting cable connections from incoming and out going and making good to the disturbed surfaces all as specified and directed.

Supply and fixing in repair LED street light luminaire 60 watt made up of pressure die cast aluminium housing with toughened glass and high power LEDsand secondary lenses with IP-66 protection, Efficeincy : 110LM/W, 10 KV SPD included complete including making connections with copper wire 1.0 sqmm complete all as specified and directed. Make :- Crompton product No. LSTP-60-CDL-M or equivalent in Havells/Philips

Supply and fixing three phase off load change over switch with handle made out of sheet metal enclosure of capacity 400 Amps, 4 pole, side handle, 415 Volts, 50 Hz complete fixing on wall with grouting of base frame and suitable nut bolts all as specified and directed

Supply and fixing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 400 Sqmm 3.5 core fixing on wall with suitable saddles or under ground as required at site complete including lugs complete all as specified and directed.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth for foundation, laying of HDPE pipe . and getting out in hard soil , complete all as specified and as directed .

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

Returning & filling in, including spreading, levelling, watering & well ramming in layers not exc 25 cm as in soil complete all as specified & directed .

Supply and fixing HDPE Pipe of size 150 mm bore, PN 10 including jointing with collars/bends complete all as specified and directed.

M&L for replacement of Earthing completely using Copper Bonded Rod of diameter more than 15mm and length of 10 feet below ground level .The material shall be low carbon high tensile copper bonded rods with 99.9 % of copper on the surface. pit shall be filled with highly conductive and eco friendly ground enhancing compound as per IEC 62561- 7 shall be not less than 30Kg per pit & PCC 1:3:6 Earth Pit chamber of size 310mm×300×170mm(W×L×H) with Cast iron cover complete all as specified and directed Make :- JMV/G Max/Pioneer Power

S&F in repair Earth continuity conductor or main earthing lead of size 25× 4mm GI fixed to wall using insulated earth strip at every 2 feet ditsance earthing strip should be fixed from 6th to ground floor and necessary termination with nuts and bolts complete all as specified and directed

Demolition of Exisiting concrete supporting block of pumps and motor exceeding 15cm of thickness above and below ground level all specfied and directed by Engineer-in-charge

M&L cement concrete 1:2:4, type B-2 (using 40 mm graded stone aggregate) as in support of Base frame with MS bolts placed in concrete and hardstanding finishing even and fair without using extra cement all as specified. Note: Location of bolts and size of bolts should macht the previous one

Supply and fixing in repair butterfly valve PN 1.6 150 mm dia complete all as specified and directed

Supply and fixing in repair CI swing type non return valve flanged end of following sizes as per IS: 5312 body, cover C-I IS: 210, PN-10 complete including replacement of nut bolts, cutting of pipe, welding complete all as specified and directed.

300 mm bore

200 mm bore

150 mm bore

100 mm bore

Supply and fix in repair, Installation, Testing & Commissioning of Motor Actuated Butterfly Valve consisiting of Quarter turn single phase Actuator and Wafer type butterfly valve of size 100 mm dia with appropriate bracket/mounting arrangement including two nos. limit switches for open and closed condition and splash proof enclosure. Specifications & Features Input Voltage: 230 V, A.C. Designed line pressure: 10 kg/sq cm. Operating Angle: 90 degrees Disc Material: CI with nylon coating Limit Switches : 02 Nos.For open and close status Mounting ::Direct mounted

Supply, Installation in repair, Testing & Commissioning of Indoor type Programmable Logic Controller based Valve Automation and communication Panel suitable for control and/or monitoring of 02 Nos. Pumps, 02 Nos Pressure Transmitter, 02 Nos. Priming Motorised Valve, 02 Nos. Solenoid Valves, 2 Nos motorized valves (+02 Spare) and 02 Nos. magnetic sensors PrimingTanks-01(2 Levels), suitable number of energy meters and 01 Nos Ultrasonic level sensor, . The panel should be of suitable size fabricated from 2.0 mm thick CRCA sheet and properly powder coated. The Panel should comprise the following items:- (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention . (h) Manual Mode Operation (all connected sub systems including all valves (in pump houses and connected buildings / overhead tanks) and pumps from the PLC based Control Panel.

Notes for item No. 37 & 38 :- To make the system fully functional. all panels shall be consisting of the following :- (a) Rack mountable Web Smart Switch with 28 ports and POE for CPE hardware and following specifications:- (i) Number of Ports 24 10/100Base-TX Ethernet ports 2, 10/100/ 1000BASE-T 2 Combo 10/100/1000BASE-T/SFP. (ii) Port StandardSupply and fixing unctions • IEEE 802.3 10BASE-T Ethernet (twisted-pair copper) • IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted-pair copper) • IEEE 802.3x Flow Control • IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper) • IEEE 802.3z Gigabit Ethernet (fiber) ANSI/IEEE 802.3 • IEEE 802.3z Gigabit Ethernet (fiber) ANSI/IEEE 802.3 Switching Capacity • 12.8 Gbps Make : Siemens, Dlink, Ubiquiti, Cisco

(b) Hot pluggable 1310 nm multimode/Single mode SFP (mini-GBIC) transceiver, supporting full duplex, Gigabit speeds on multimode/Single mode fiber for distances of up to 550m/550m/10km on 62.5µm/50µm/ 9µm respectively in a metal housing to reduce EMI and to increase durability Make : Dlink, Ubiquiti, Cisco, Siemens, HP

(c) Rack Mountable LIU with the following specifications:- (i) Rack Mountable 12 Port Unloaded LIU (ii) Aluminium Base Material (iii) Slim 1 U mounting height (iv) Metal Shelf Aluminium 1.2 mm thick (v) Splice tray Aluminium 0.6mm (vi) Winding Panel – Plastic (vii) Cable Plug – Rubber for minimum 2 cable entries (viii) Adaptor Panel Aluminium 1.5 mm thick (ix) 2 fiber spools built in for 900 um tight buffered fibre storing (x) Capable of storing upto 3 mts of 900 um tight buffered fibre per adaptor Make : Dlink, Ubiquiti, Cisco

(d) SC-LC Duplex SM Patch Cord 0.9 mm dia of suitable length (i) Size 0.9mm dia (ii) Insertion Loss <=0.2 db, max 0.3 db (iii) Return Loss PC>=45dB, UPC>=50dB, APC>=60dB (iv) Connector Ferrule Ceramic (v) Apex Offset <50um (vi) Fiber Height +-100nm (vii) End Face Radius of Curvature 7mm<R<25mm (viii) Repeatability <=0.2 dB 1,000 times mating cycles (ix) Working Temp -40deg C to +85 deg C Make : Dlink, Ubiquiti, Cisco

(e) SC Simplex Coupler/Adaptor (i) Insertion Loss <=0.2 dB for Zirconia Sleeve (ii) Sleeve/Ferrule Withdrawl Force 2.0N to 5.9N Make : Dlink, Ubiquiti, Cisco

(f) Adaptor Panel (i) 6 port adaptor Panel for SC Adaptors Make : Dlink, Ubiquiti, Cisco

(g) SC-SM-Simplex Pigtail of suitable length (i) Insertion Loss <=0.2 db, max 0.3 db (ii) Return Loss PC>=45dB, UPC>=50dB, APC>=60dB (iii) Connector Ferrule Ceramic (iv) Apex Offset <50um (v) Fiber Height +-100nm (vi) End Face Radius of Curvature 7mm<R<25mm (vii) Repeatability <=0.2 dB 1,000 times mating cycles (viii) Working Temp -40deg C to +85 deg C Make : Dlink, Ubiquiti, Cisco

(h) CAT6 UTP 24 AWG Patch Cord of suitable length, Plug 30U snag less Make : Dlink, Finolex

Seamless Integration of the above PLC Panels into the Existing SCADA System incorporating (a) Development: (i) SCADA Screens for new Updated Panel configuration (ii) Layout for App new Updated Panel configuration (iii) Report Format new Updated Panel configuration

(b) On-site development: (i) Modifications in SCADA Screens (ii) Modifications in reporting format (iii) Modifications in App layout

Above All automation panel should connected to existing SCADA server and any other leftout devices and accessories require to commissioning should be consider and same should be include in quoted rates and department will not pay extra cost for the same. Make of Control Panel: Cimcon Software Pvt Ltd/ Reckronic Devices and Systems / Sombansi Schneider/Universal Switchgear. Note :- Cost for Synchronising of panel in to existing SCADA system is in contractors scope only and no extra payment shall be given to the contractor by the department.

Supply, Installation in repair, Testing & Commissioning of motor actuated ball valve suitable for 25 mm GI pipe for priming of pump including all necessary GI fittings with following specifications: 25 mm Pressure rating: 10 kg / sq. cm.

Supply, Installation in repair, Testing & Commissioning of direct acting type release solenoid valve for air release during priming; with follwing specifications : Size: 10 mm, Pressure rating: 10 kg / sq. cm., Type: Normally closed

Supply, Installation in repair, Testing & Commissioning of pressure Transmitter with following specification including necessary power pack for supply of DC : Power supply: 10-36 V DC Process connection: G ½ “ Enclosure: whether proof IP 65 Process temperature: -30 to 120 celcius Accuracy: 0.25 %

M&L for earthing with glvanised earth plate 60 cmmx60cmx6mm thick buried directly in ground verticaly to depth not less than 2.5 mtr deep below ground level connecting 25x4mm GI strip by means of bolt nut chek nut and washer of galvanised iron all show in electrical plate no 03 SSR Part I including necessary exvation earth in soft/loose soil concrete pit in PCC 9 and (1;2:4) pre cast iron pit and pit cover with handle of 8 mm dia MS rod and connected to test point and aluminum strip of 25x3mm with insulator strip between from panel on terrace to earth pit all as specified and directed

Supply, Installing in repair,Testing and Commissioning of Ultrasonic Level Transmitter Range : 0-5 metres Accuracy : 0.5 % minimum Supply Voltage : 24V DC Output : 4-20 mA Ultrasonic Frequency:75 kHz burst, rep. rate 96 ms Delay at Power-up: 1.5 seconds Temperature Effect: Uncompensated: 0.2% of distance/°C &Compensated: 0.02% of distance/°C Delay at Power-up: 1.5 seconds Resolution: 1.0 mm Output Response Time: 100 ms to 2300 ms Minimum Window Size: 20 mm Environmental Rating: Leakproof design is rated IEC IP67; NEMA 6P Operating Conditions: Temperature: –20 °C to 70 °C (–4 °F to 158 °F) Maximum relative humidity: 100% Make : Endress/ Hauser/ Banner/ Krohnc/ Marshal/ Siemens

Supply, Installation in repair, Testing and Commissioning of Float type Point Level Sensor with the following specifications; Type: Magnetic Magnet: Ring type Switch: Reed Switch (Epoxy sealed) Connecting Cable: Teflon Make: RECKTRONIC DEVICES AND SYSTEMS / TECHTROL / CRYSTAL

Supply & fixing in repair 4 core x 1.5 sq mm PVC sheathed and PVC insulated, armoured, FRLS, copper cable on wall complete all as specified and directed.

Supply & fixing in repair 6 core x 1.5 sq mm PVC sheathed and PVC insulated, armoured, FRLS, copper cable fixed on wall with clamps complete all as specified and directed.

Supply & fixing in repair 5 pair 0.5 sq mm PVC sheathed and PVC insulated, armoured, FRLS, copper cable fixed on wall with clamps complete all as specified and directed.

Supply, Installation, Testing and Commissioning of outdoor type Wimax CPE stations operating on license free frequency of 5 Ghz at suitable locations along with suitable antenna complete with mounting pole and accessories to be connected to the ofc network of each node and establish wireless connectivity with the central server. Make : UBIQUITI/ SIEMENS

Supply, Installation in repair , Testing and Commissioning of outdoor type Wimax Base stations operating on license free frequency of 5 Ghz at suitable locations along with suitable antenna complete with mounting pole and accessories to be connected to the ofc network of each node and establish wireless connectivity with the central server. Make : UBIQUITI/ SIEMENS

Supply, Installation in repair, Testing and Commissioning of Armoured CAT 6 UTP cable on walls Make : D Link, Finolex, Polycab

Supply, Installation in repair, Testing and Commissioning of OFC Cable to be pulled over head and duly fastened/attached to a PVC cpoated messenger wire / stay wire of gauge either with the required clamps of suitable size not more than 3 feet apart or with a web between the OFC and messenger wire along with endplates at both ends of the suspended cable (a) 6F Single mode OFC suitable for outdoor networking applications (i) 6 Fibers type single mode, wavelength 1310, Attenuation 0.38/km (ii) Outer jacket of HDPE sheath (iii) Jelly Filled Core (iv) Wrapped with Corrugated Steel Tape (v) Armoured with a pair of Steel Wire for rigidity (vi) Anti Termite and rodent repellent (vii) Water Proof and moisture resistant

Supply, Installation in repair, Testing & Commissioning of Motor Actuated Butterfly Valve consisiting of Quarter turn single phase Actuator and Wafer type butterfly valve of size 80 mm dia with appropriate bracket/mounting arrangement including two Nos limit switches for open and closed condition and splash proof enclosure. Specifications & Features Input Voltage: 230 V, A.C. Designed line pressure: 10 kg/sq cm. Operating Angle: 90 degrees Disc Material: CI with nylon coating Limit Switches : 02 Nos.For open and close status In built Serial / USB communication Port In built data logger with memory In built SD Card Space Heater Mounting ::Extended type with universal joint for installation 18 -24 inches above ground level with angle mounting including raising of existing chamber if required. Make: EMTORK / HASEL HOFENER / RITETORK /SIEMENS/ HONEY WELL

Supply, Installation in repair, Testing & Commissioning of Motor Actuated Butterfly Valve consisiting of Quarter turn single phase Actuator and Wafer type butterfly valve of size 300 mm dia with appropriate bracket/mounting arrangement including two Nos limit switches for open and closed condition and splash proof enclosure. Specifications & Features Input Voltage: 230 V, A.C. Designed line pressure: 16 kg/sq cm. Operating Angle: 90 degrees Disc Material: CI with nylon coating Limit Switches : 02 Nos.For open and close status In built Serial / USB communication Port In built data logger with memory In built SD Card Space Heater Mounting ::Extended type with universal joint for installation 18 -24 inches above ground level with angle mounting including raising of existing chamber if required. Make: EMTORK / HASEL HOFENER / RITETORK /SIEMENS/ HONEY WELL

M & L Construction of brick masonery valve chamber in repair of size 1.2 x 1.2 x 1.2 M (internal dimension) (above GL 0.30 mtr) suitable for fixing of sluice valves, 15cm thick foundation using PCC 1:4:8 type D-2 over 15cm thick hardcore of broken stone, 23cm thick brick walls built in cement and sand mortar 1:4, 15mm thick internal and external plaster including top of floor in cement and sand mortar 1:3, 15mm thick, finished even and smooth, without using extra cement, 10 mm thick plate cover on 70mm x 70mm x 10 mm MS angle frame embeded in PCC 1:2:4 type B-1coping, having rectangular, hinged, opening of size 150 x 100mm with locking arrangements ,hold fasts, etc, applying one coat of red oxide primer and two coats of synthetic enamel paint to all steel surfaces and earth work in any type of soil including disposal of debris outside MD land complete all as specified.

Supply ,installation in repair,testing of Pressure relief valve of 150mm following specifications Design - Pilot Operated, Globe type MOC Body & Cover - Ductile Iron MOC Trim - SS 304 / ASTM A 351 GR. CF8 MOC Spring - SS 304 MOC - Diaphragm - Nylon Reinforced Nitrile Set Pressure - 55 to 75 Psi-g Temp .- Ambient Application - Water Ends Connection - Flange end as per ASME including excavation , cutting existing 150mm pipe all as specfied and directed by Engineer-in-charge.

Supply ,installation in repair,testing of Pressure relief valve of 80mm following specifications Design - Pilot Operated, Globe type MOC Body & Cover - Ductile Iron MOC Trim - SS 304 / ASTM A 351 GR. CF8 MOC Spring - SS 304 MOC - Diaphragm - Nylon Reinforced Nitrile Set Pressure - 55 to 75 Psi-g Temp .- Ambient Application - Water Ends Connection - Flange end as per ASME including excavation , cutting existing 150mm pipe all as specfied abnd directed by Engineer-in-charge.

Taking down of old unserviceable GI tubing from the walls of following sizes including removing old rusted clamps including making good to the disturbed surfaces complete all as specified and directed :-

40 mm bore

50 mm bore

80 mm bore

Supply/Fixing of steel water tubing, galvanised, Medium grade with all fittings in shafts such as nipple, union, socket, elbow, bends, fixed to wall including necessary GI saddles with anchor fasteners & capacity up to 15 th floor in high rise buildings in short piece/length, including breaking the existing brick wall for replacement of corroded GI pipe in/on wall and making good the disturbed surfaces complete all as specified and directed by Engineer-in-charge.Note (1)Work to be carried out in high rise buildings plain wall or in shafts or in terraces or inside the flats for cutting the existing GI pipe line and replace the same with new GI pipe in short piece or full length.

40 mm bore

50 mm bore

80 mm bore

S&F in repairs PVC water storage Tank with cover 2 layer, ISI marked, pure anti microbial round type and making connections including replacement of new GI fittings i.e. tank nipple, washers, float valves and Gate valves and Pipes for connecting the existing Inlet/delivery lines, testing complete all as specified and directed for the following capacity :- Note :- Gate valves and GI pipe only shall be paid under relevant item of Schedule 'A' remaining items shall be deemed to be included in the item rate.

5000 Ltr capacity

3000 Ltr capacity

Supply and fix in repairs in existing line, gun metal gate valve with iron wheel head screwed both ends for iron pipe including fittings i.e. union, socket etc complete all as specified of following sizes :-

40 mm bore

50 mm bore

80 mm bore

M& L for Cleaning of loft tanks of capacity 170 to 275 ltrs in existing position by mechanised pressure, cleaning using PVC tank cleaning solution and draining out the water by wet vaccum pump, rinsing with clean drinking water complete all as specified. Note : Any damage to pipe and PVC tank during cleaning shall be made good by the contractor at his own cost.

Supply & fix in replacement of unserviceable PVC loft tank (HDPE) of capacity 275 ltrs with complete fitting including 03 Nos adopter with washer for inlet/outlet over flow as per manufactureres instructions complete all as specified and directed by Engineer-in-Charge

Supply and fixing replacement PVC profile suitable for 275 ltr loft tank including fixing of aluminium channel around the profile complete all as specified and directed by Engg-In- Charge.

Cleaning of underground sump of any capacity cleaning the floors, wall and ceiling portion of sump etc by Mechnical high pressure spray and steel wire brush to remove Algae/dirt/foreign dirt completely and soaking out the water/dirt with a high pressure wet vaccum pump and removing spoils out side of MD land land distance exc 5 KMs & n.exc 10 KMs and applying spray of approved chemical etc. complete all as specified and as directed by Engineer-in-charge . Note :- 1. Rates deemed to be included for pumping out water left below foot valve. 2. Rate include the painting of two coats of enamal paint with visible colour and capacity of sump about date of cleaning and due date for cleaning complete all as specified.

Sump capacity of approximately 9,20,000 liters

Sump capacity of approximately 16,00,000 liters

Sump capacity of approximately 14,00,000 liters

Sump capacity of approximately 4,50,000 Liters

Sump capacity of approximately 3,20,000 Liters

Sump capacity of approximately 2,00,000 Liters

Sump capacity of approximately 2,50,000 Liters

Sump capacity of approximately 1,50,000 Liters

Cleaning of PVC and RCC water storage tank in low and high rising buildings(G+14) by mechanical high pressure spray and remove all foreign matter completly and soaking out the water/dirt with a high pressure wet vaccum pump and removing spoils out side of MD land and complete all as specified and as directed by Engineer-in-charge . Note: Rate include the painting of two coats of enamal paint with visible colour about date of cleaning and due date for cleaning complete all as specified.

OH Tank of capacity 5000 Litres

OH Tank of capacity 3000 Litres

OH Tank of capacity 10000 Litres

OH Tank of capacity 15000 Litres

S&F FRP lid cover for PVC water storage tank complete accessory for closing and locking arrangement suitable for various capacitys as approved by BMC

For capacity of 5000 litres

For capacity of 3000 litres

Cleaning the vegetation including grass, bushes small trees and all vegetation growth complete including uprooting of bushes and small trees around the installation/sump/OH reservoir, valve chamber etc. filling the rough holes with earth and levelling the surfaces by removing all debris to a distance n.exc.50m complete all as specified and directed.

Supply/Fixing in repair/replacement of internal steel water tubing with CPVC pipes SDR 11 & PlainCPVC SDR 11 fittings in wall and shafts including necessary saddling and and work to be done in high rise building up to 15 th floor short piece/length, including breaking the existing brick wall for replacement of corroded GI pipe in/on wall and making good the disturbed surfaces complete all as specified and directed by Engineer-in-charge of the following size :-

20 mm Nominal outside dia

25mm Nominal outside dia

Supply & Fixing in repairs Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc with Fe 410 -W (Gde- E- 250) including making paint with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. Note:Contractor should survey each quarter in old and new navy nagar and highly rusted angle should be change accordingly.

Material and labour for bacteriological and chemical analysis of water sample at govt approved lab (Iso 9001:2008)including collecting sample from pumphouse using labelled owned sample jar and testing every month all directed and specfied by Engineer-in-charge

Checking of over head tanks of any capacity , making arrangement of mosquito proofing of the tank from overflow side with new GI tank nipples, socket, barrel nipple , elbow, MS wire net, locking the existing tank cover to avoid entry of lizards, mosquitos inside the tank, tightening of all inlet and out let connections to make the tank no leaking of water complete including painting with white colour paint on base coat and writing the letters of black colour of the following details all as specified and directed :- (a) Date of cleaning (b) Date of Next due (c) Tank capacity

Supply, Installation Testing & Commissioning in repair of Motor Actuated Butterfly Valve (With manual operating wheel) consisiting of Quarter turn single phase Actuator and Wafer type butterfly valve of size 200 mm dia with appropriate bracket/mounting arrangement including two nos. limit switches for open and closed condition and splash proof enclosure. Specifications & Features Input Voltage: 230 V, A.C. , Designed line pressure: 16 kg/sq cm. Operating Angle: 90 degrees, Disc Material: CI with nylon coating Limit Switches : 02 Nos.For open and close status Mounting : Extended type with universal joint for installation 18-24 inches above the pipe level with angle mounting including raising of existing chamber as required at site. Note :-1. Rates also including of cutting, welding and any modifications in existing line with suitable DI/CI fittings with joints and its fixing are completely included in the item rate and no extra cost will be claimed by the contractor. Make :- Emtork/Hasel Hofener/Ritetork/Siemens/Honeywell Note :-2 Contractor's shall visit the site before quoting the rate of the item.

Notes for item No. 74 & 75:- To make the system fully functional. all panels shall be consisting of the following :- (a) Rack mountable Web Smart Switch with 28 ports and POE for CPE hardware and following specifications:- (i) Number of Ports 24 10/100Base-TX Ethernet ports 2, 10/100/ 1000BASE-T 2 Combo 10/100/1000BASE-T/SFP. (ii) Port StandardSupply and fixing unctions • IEEE 802.3 10BASE-T Ethernet (twisted-pair copper) • IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted-pair copper) • IEEE 802.3x Flow Control • IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper) • IEEE 802.3z Gigabit Ethernet (fiber) ANSI/IEEE 802.3 • IEEE 802.3z Gigabit Ethernet (fiber) ANSI/IEEE 802.3 Switching Capacity • 12.8 Gbps Make : Siemens, Dlink, Ubiquiti, Cisco

(b) Hot pluggable 1310 nm multimode/Single mode SFP (mini-GBIC) transceiver, supporting full duplex, Gigabit speeds on multimode/Single mode fiber for distances of up to 550m/550m/10km on 62.5µm/50µm/ 9µm respectively in a metal housing to reduce EMI and to increase durability Make : Dlink, Ubiquiti, Cisco, Siemens, HP

(c) Rack Mountable LIU with the following specifications:- (i) Rack Mountable 12 Port Unloaded LIU (ii) Aluminium Base Material (iii) Slim 1 U mounting height (iv) Metal Shelf Aluminium 1.2 mm thick (v) Splice tray Aluminium 0.6mm (vi) Winding Panel – Plastic (vii) Cable Plug – Rubber for minimum 2 cable entries (viii) Adaptor Panel Aluminium 1.5 mm thick (ix) 2 fiber spools built in for 900 um tight buffered fibre storing (x) Capable of storing upto 3 mts of 900 um tight buffered fibre per adaptor Make : Dlink, Ubiquiti, Cisco

(d) SC-LC Duplex SM Patch Cord 0.9 mm dia of suitable length (i) Size 0.9mm dia (ii) Insertion Loss <=0.2 db, max 0.3 db (iii) Return Loss PC>=45dB, UPC>=50dB, APC>=60dB (iv) Connector Ferrule Ceramic (v) Apex Offset <50um (vi) Fiber Height +-100nm (vii) End Face Radius of Curvature 7mm<R<25mm (viii) Repeatability <=0.2 dB 1,000 times mating cycles (ix) Working Temp -40deg C to +85 deg C Make : Dlink, Ubiquiti, Cisco

(e) SC Simplex Coupler/Adaptor (i) Insertion Loss <=0.2 dB for Zirconia Sleeve (ii) Sleeve/Ferrule Withdrawl Force 2.0N to 5.9N Make : Dlink, Ubiquiti, Cisco

(f) Adaptor Panel (i) 6 port adaptor Panel for SC Adaptors Make : Dlink, Ubiquiti, Cisco

(g) SC-SM-Simplex Pigtail of suitable length (i) Insertion Loss <=0.2 db, max 0.3 db (ii) Return Loss PC>=45dB, UPC>=50dB, APC>=60dB (iii) Connector Ferrule Ceramic (iv) Apex Offset <50um (v) Fiber Height +-100nm (vi) End Face Radius of Curvature 7mm<R<25mm (vii) Repeatability <=0.2 dB 1,000 times mating cycles (viii) Working Temp -40deg C to +85 deg C Make : Dlink, Ubiquiti, Cisco

(h) CAT6 UTP 24 AWG Patch Cord of suitable length, Plug 30U snag less Make : Dlink, Finolex

Seamless Integration of the above PLC Panels into the Existing SCADA System incorporating (a) Development: (i) SCADA Screens for new Updated Panel configuration (ii) Layout for App new Updated Panel configuration (iii) Report Format new Updated Panel configuration

(b) On-site development: (i) Modifications in SCADA Screens (ii) Modifications in reporting format (iii) Modifications in App layout

The quoted cost shall deem to include the cost of communication for 12 months from the date of completion.

Above All automation panel should connected to existing SCADA server and any other leftout devices and accessories require to commissioning should be consider and same should be include in quoted rates and department will not pay extra cost for the same. Make of Control Panel: Cimcon Software Pvt Ltd/ Reckronic Devices and Systems / Sombansi Schneider/Universal Switchgear. Note :- Cost for Synchronising of panel in to existing SCADA system is in contractors scope only and no extra payment shall be given to the contractor by the department.

Supply, installation in repair, testing & commissioning of Motor actuated butterfly valve consisting of Quarter turn single phase actuator and water type butterfly valve of size 100 mm dia with appropriate bracket/mounting arrangement including two Nos limit switches for open and closed condition and splash proof enclosure. Specifications & features Input Voltage : 230 V, AC Designed line pressure : 16 Kg/sq cm Operating angle : 90 degrees Disc material : CI with nylon coating Limit switches : 02 Nos for open and close status In built serial/ USB communication port In built data logger with memory In built SD Card Space Heater Mounting : Extended type with universal joint for installation 18-24 inches above ground level with angle mounting including raising of existing chamber if required. Make : EMTORK/ HASEL HOFENER / RITETORK/ SIEMENS / HONEY WELL

ASHOK ENTERPRISES