8147 SPECIAL REPAIRS TO ORS MD ACCN NO 54 57 AN D 57 ZOZILA LINE AT AFSMC SPECIAL REPAIRS WKS BLDG NO 80 88 89 AND 89 AT ZOZILA LINE PROVN OF PARKING SHED AT AFSMC AND PROVN OF SCREEN WALL IN VERANDAH AT ADMISSION CELL AT AFMC PUNE

Amount

Demolition of cement concrete in ground floors and paving not exc 15 cm thick (below or above ground level) un-reinforced cleaning the premises and removal of rubbish out side the MD land complete all as directed.

Demolition of cement concrete un reinforced of any description & in any position not otherwise specically provided for cleaning the premises and removal of rubbish out side the MD land complete all as directed.

Demolition of cement concrete reinforced (Re-inforcement cut as required to facilitate demolition) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal of debris out of MD land complete all as directed.

Taking down cement plaster on brick, concrete or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc and removal of rubbish out side MD land complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as directed.

Dismantling of stone slab/tiles of any description of thiockness laid bedded & pointed in cement mortar in floors, hard standing Apron etc removing serviceable tiles and rubbish out side MD land complete all as directed.

Taking down chowkats or frames of wooden/steel (door/window/ventilator) exc 1.5 sqm and n exc 4.0 sqm (without taking off shutters from the frames) & removing from site including cutting out hold fasts and making good to distrubed portion complete all as directed.

All as per item No 7 here-in-before but n exc 1.50 Sqm each.

Dismantling timber scantling, unframed in post, rafters, purlines etc over 40 sqcm in section complete all as directed.

Dismantling battens for tiles, shingles etc, of any size and description spaced exc 15 cm including tiling fillets complete all as directed.

Dismantling single layer of manglore pattern or similar tiles in roofing including ridges, hips, complete all as directed.

Dismantling ceiling board / Partition board of any description, fixed in any position with nails including frame work complete all as directed.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete including removal from site all as and directed.

Demolition brick work or stone/ boulders masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work and precast concrete articles and revomcal from site complete all as directed.

Demolition and breaking of drain pipes AC/CI/PVC set in cement mortar or adhensive all as directed of 75 mm to 110 mm dia

Taking up or down carefully 15 mm bore steel water tubing , and connections with fittings including removal from site complete all as directed.

All as per item No 16 here-in-before but 20mm bore.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and as directed.

Excavation in post holes (or similar holes) each n.exc 0.5 cum and getting out in hard/ dense soil and removing surplus soil at a distance n.exc 50m and making good surface all as specified and directed.

Removing excavated soil n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

M & L for hardcore (broken stone or boulders) of gauge exc 63 mm but n exc 100 mm , deposited, spread and levelled in layers n exc 15 cm thick, watered and rolled/rammed to a true surface completed all as specified and directed.

M & L for cement concrete (1:3:6) type C1 (using 20 mm graded granite stone aggregate) for fixing of hold fast etc complete all as specified and as directed complete all as specified and directed.

M & L PCC (1:3:6) type- C-1 (using 20 mm graded stone aggregate) as in roof kerbs , rounded or chamfered on edges, including necessary form work complete all as specified.

M & L for precast reinforced cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) in landings, cover slabs (for manholes etc) shelves and similar articles with plain faces and set in cement mortar 1:4 complete all as specified and as dircted.

M & L for PCC (1:2:4) type B2 (using 40 mm graded stone aggregates) as in foundation of posts complete all as specified and directed.

M & L for PCC (1:2:4) type B0 (using 12.5 mm graded stone aggregates) as in kerb of interlocking tiles complete all as directed.

M & L for Reinforced cement concrete (nominal mix) in Beams, cantilevers, bressummers, lintels over 1.5m span Type A1 (1:1.5:3) (20mm graded aggregate) complete all as specified and directed .

M & L for block masonry with solid blocks of precast cement concrete (1:5:8)class designation C-5 (using 20 mm graded stone aggregate) exc 10 cm in width and setting in cement mortar (1:6) complete all as specified and as directed.

M & L for cutting into old stone masonry to form toothings for and bonding in new brick or stone or PCC block masonry work including making good in cement mortar complete all as specified and directed.

M & L for for cutting holes in brick wall, built in CM for inserting hold fast and making good dismantled portion in CM 1:3 depth of embedded portion of hold fast or lugs measured from the face of the jamb into the wall exc half brick but n exc one brick thick complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for flat fair finished surfaces of concrete complete all as specified and directed .

M & L for 2nd class hard wood, clean sawn, in scantling timber framed, secured with nails as in fillet, rafter purlins etc complete all as specified and as directed.

S & F 2nd class hard wood plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joint complete all as specified and directed.

S & F 35 mm thick Flush shutters, solid core construction, with particle board core and one face is covered with decorative face veneer with lipping/frame to match, complete all as specified and directed.

S & F 35 mm thick 2nd class hardwood glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc, The size of the rail and site as per IS 1003 (part -I), Kiln seasoned and chemically presure treated as specified and directed by Engr in charge.

S & F 2nd class hardwood plain, framed, panelled shutters, 35mm thick (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats as specified and directed by Engr-in -Charge.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, in opening as per manufacturer's instructions and as directed by Engineer-in-Charge complete all as specified and as directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles end plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded seat to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement and fixed in the frame at site as per specification and drawing all as specified in SSR part II.

S & F factory made uPVC white colour sliding window. Three track made of extruded profiles with wall thickness of 2.3 mm. Window profile with hollow section with multi chamber, Frame (88 mm x 52 mm), sliding sash (42 mm x 67 mm), sliding mesh sash (42 mm x 57 mm), Sliding interlock(one vertical length in each shutters) (45.5 mm x 28 mm), Glazing bead (24.5 mm x 16 mm) will be mitered cut and fusion welded at all corners, including railing of holes for fixing of hardware and drainage of water etc, making arrangement for fixing of hardware , EPDM gasket, 1.2+- 0.2 mm thick galvanised steel Frame (30 mm x 18 mm) 2 Nos, sliding sash (30 mm x 18 mm), sliding mesh sash(26 mm x 10 mm) , profile to be inserted in required profile , frame will be fixed to the wall with 8 mm x 100 mm long fasteners. Hardware : (Touch lock of zinc alloyed (white powder coated) , steel roller system, stainless steel wirecloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and required accessories) Area not exceeding 2.00 Sqm each.

S & F 100 mm size MS but hinges, medium weight cold rolled complete all as specified and directed.

S & F 200 mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F 150 mm long mild steel pressed hanle, oval type, stove enamelled black, complete all as specified and directed.

S&F 300 mm long mild steel sliding door bolts, plated type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F aluminimum anodised curtain rod 20 mm dia dearative type powder coated complete all as specified and directed .

S & F decarative type funnel/bracket powder coated to suit the curtain rod of 20 mm dia complete all as specified and directed.

S & F in repairs 300 mm MS ordinary rat tail rod pattern spring including roller and roller plate complete (including dismantling existing door spring by means of welding) complete all as specified and as directed.

M&L for MS structural steel work, framed, as in trusses purlins, rafter, post etc conforming to grade E-250 (Fe-410W, quality A) including shaped washers including necessary cutting required length, notching drilling, riveting and or welding or connecting with nut bolts with angle cleats, gusset plate and also erecting in true position complete all as specified and as directed,

S & F for mild steel as in main and cross beams, hip and jack rafters, post and purlins where connected to common rafters and running rails fixed with angle cleats or other connecting plates, including welding confirming to IS grade including sharp coat of primer zinc chrome red oxide etc complete.

S & F framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, framed work of watertanks and similar work confirming to Fe 290 Gde -E-165.

S & F MS work in small articles such as hold fast etc. all as specified and directed.

S & F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc complete as specified size of frame 125x60 mm including PCC (1:3:6), type C-0, using 12.5 mm graded stone aggregates as in filling of pressed steel frames complete all as specified and directed.

S & F steel windows with side hung shutters including projecting type hinges and steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed.

All as per item No 53 here-in-before but without glazing bars.

S & F steel ventilators with top hung shutters including hinges, steel peg stay and guard bars complete all as specified and as directed.

M & L TMT bars 10mm dia and over , cut to length , bent to shape required including cranking , bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 56 here-in-above but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders complete all as specified and directed .

S & F pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50 mm thick fixed in any position of any colour having tensile strength of 550 Mps and 150 GSM as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour as in ridge and straight flashing fixed with self tapping screws complete all as specified and as directed.

M & L Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw (as per manufacturers instructions) to Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including providing two coats of oil bound distemper complete all as specified and directed.

M & L for 10 mm thick gypsum board for ceiling on and including aluminium powder coated grid work 60 cm x 60 cm with with using 36.5 mm x 23.5 mm x 1.5 mm thick main tee, 23.5 x 23.5mm x 1.28 mm cross tee, and 25 mm x 25 mm x 1.5 mm angle fixed to wall for false ceiling including necessary nuts for securing frame work to ceiling suspended @ 120 cm C/C both ways, size of grid shall be 605 mm x 605 mm complete all as specified and directed.

M & L for decorative POP cornices/moulding of pattern as approved by Engr-in-charge of cross section area exc 13 Sqcm and not exc 25 Sqcm complete.

M & L for 100mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate ) as in sub base complete all as specified and directed.

M & L for PCC (1:2:4) type B2 (40 mm graded aggregate) 100 mm thick using as hardstading complete all as specified and directed.

M & L for 75 thick PCC (1:4:8) type D2 (using 40 mm graded aggregate) as in sub base/flooring complete all as specified and as directed.

M & L for PCC (1:3:6) type C2 of 75 mm thick as in plinth protection finished even and smooth without using extra cement complete all as specified & directed.

M & L for 100 mm PCC (1:2:4) type B1 (20 mm graded aggregate) finishing cement concrete surface even and smooth with out using extra cement complete all as specified and directed.

M & L for 40 mm PCC (1:2:4) type B1 (20 mm graded aggregate) using as levelling couse below tiles complete all as specified and directed.

M & L 25mm thick PCC 1:2:4 type B-1 (20mm graded stone aggregate) for leveling course to receive the top layer like tiles complete all as specified and directed.

M & L granite (of any type) work (table rubbed and polished) 18 to 20 mm thick in jambs, window cill, and flooring in CM 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite with and including screed bed or bedding layer 15 mm thick, in CM 1:6 on stone or block masonry surfaces complete all as specified and directed.

M & L for machine cut Kota stone slab flooring 20-25mm thick laid and jointed with grey cement slurry mix with pigment to match the shade of the slab incl rubbing and mirror polishing complete over and incl 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M & L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floor set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles, over and including 15 mm thick cement screed bed in CM 1:6 complete all as specified and directed.

All as per item No 72 here-in-above but exc 0.11 Sqm and n exc 0.18 Sqm.

M & L for 300x200x7 mm thick, glazed ceramic, coloured tiles in skirting/daddos etc set and jointed in neat ceemnt slurry and pointed in white or colored cement to match complete over and including 10 mm thick backing coat in CM 1:3, including triangular filleting in CM 1:3 on top complete all as specifed & directed.

M & L (double charged) Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, as in skirting , set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick backing coat in CM 1:4 all as specified and as directed by Engr-in-Charge.

M & L for precast cement concrete glazed Interlocking tiles 60mm thick in floor/pavement laid over and including 30mm thick sand cushioning laid dry to the profile including vibrating with surface vibrator after laying of tiles complete all as directed by Engineer-in-Charge.

M & L for Rounding to edges of granite stone slabs one edge, such as in window jambs,steps, cooking platform, and other similar situations complete.

M & L rendering 15 mm thick in CM 1:6 on brick / stone masonry surface (fair faces) finished even and smooth without using extra cement complete all as specified and as dircted.

M & L for rendering 15 mm thick in CM 1:4 on stone masonry surface other than fair faces of brick finished even and smooth with thin layer of sponge finish complete all as specified and as directed.

S & F sheet glass ordinary quality, 3 mm thick and glazing with oil putty in square n exc 0.50 sqm in each pane complete all as specified and as directed.

S & F 4 mm thick Sheet glass, ordinary quality, tinted and glazed in UPVC framing including necessary fittings in square n exc 0.5 sq. m in each pane complete all as specified and directed.

M & L for preparation of newly plastered surface of wall and applying three coat of white wash complete all as specified and as directed.

M & L for preparation new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

All as per item No 83 here-in-before but only one coat on old decorated surfaces.

M & L for preparation new plastered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of walls and applying two coats of acrylic emulsion paint over 2 mm thick wall care putty complete all as specified and directed.

M & L for preparation of old painted surfaces and providing one coat of white wash on walls complete all as specified and directed.

M & L for preparation of old painted surfaces and providing one coat of cement base paint on walls complete all as specified and directed.

M & L for preparation of new wood and wood based surface of any description not otherwise described over 10 cm width or girth and applying , two coats of creosote oil complete all as specified and as directed.

M & L for preparation of old wood and wood based surface of any description not otherwise described over 10 cm width or girth and applying , one coat of creosote oil complete all as specified and as directed.

M & L for preparation of new wooden surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for preparation of new steel surface of any description not otherwise diescribed over 10 cm width or girth and applying two coats of sythetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and as directed.

M & L two coats of syenthic enamel paints on steel surface n exc 10 cm in width or girth over one coat of red oxide primer incl preparation of surfaces complete all as specifed and directed.

S & F 15 mm bore GI tubing ISI marked medium grade with and including all fittings laid in floors/ceiling complete all as specified and directed.

All as per item No 94 here-in-before but 20mm bore.

S & F for 110 mm dia PVC SWR pipes single socketed in any length with rubber ring joints fixed to floor / walls including clamp etc complete all as specified and directed.

All as per item No 96 here-in-before but 75mm dia pipe.

S & F PVC (SWR) Tee any radius 110 mm bore provided with access door complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends, of any radius complete all as specified and as directed.

S & F PVC (SWR) 75 mm bore vent cowl complete all as specified and directed

Supply and fix 500 ltrs capacity rotational moulded polyethylene water storage tnaks (cylindrical vertical with closed top) double layered ISI marked, hoisted & fixed in position including 20 mm dia ball brass valve with polythene float and flynut, including taking down old one complete all as specified and directed.

S & F in repair chromium plated 15mm dia bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipes complete all as specified and directed.

S & F in repair chromium plated angular stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed for bore of size 15mm.

S & F in repairs chromium plated 15mm dia pillar taps , cast copper alloy with crutch or butterfly handle, screwed down, high pressure or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipes complete all as specified.

S & F in repair PVC 32 mm dia flush pipe suitable for WHB complete all as specified and directed.

S & F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S & F in repairs vitreous china squatting pan Orissa pattern wash down water closet of size 580x440 mm, white, with integral foot rests complete with P or S trap, and all necessary fittings complete all as specified and directed.

S & F in repairs vitreous china wash hand basin white 550 x 400 mm flat back including providing CI brackets, CP brass waste coupling 32 mm dia with check nut washer etc fixed complete all as specified and as directed.

S & F in repairs PVC flushing cistern low level 10 ltrs capacity including brackets for flush tank, PVC flush pipe and all necessary fittings etc complete all as specified and directed.

S & F in repairs chromium plated soap dish fixed to plugs with chromium plated brass screws as complete all as specifed and directed.

S & F in repairs brass chromium plated Tubular towel rail 20mm dia "D" type 60cm long complete all as specifed and directed.

S & F in repairs 125 mm dia swivel type brass chromium plated shower rose of approved quality complete all as specifed and directed.

S & F 100 mm dia grating dooms of PTMT (minimum weight 25 gms) complete all as specified and as directed.

S & F stainless steel plate rack made of 1.00 mm thick sheet grade SS- 304 of standard size 36"x36"x8" and of approved quality of finish all as spd and directed.

S & F stainless steel sink with drainage board made of stainless steel 1 mm thick with plugs washers and waste including bedding in cement mortor or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm X 330mm X 160 mm complete all as specified and directed.

M & L for Point wiring using colour coding as per IS with 1.5 Sq mm multistranded copper conductor single core FRLS PVC insulated sheathed 1100 Volts, ISI-694 marked drawn through Casing & Capping on wall /roof/ floor along with suitable fittings, with MS sunken boxes of 1.6 mm thick of suitable size including making good disturbed surfaces to match with existing finishes including 3mm thick laminated sheet ISI marked for having switches sockets etc along with1.5 Sq mm copper conductor FRLS, PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly including taking down old existing wiring alongwith fixtures and fittings complete all as specified for the following :

One light point controlled by one, one way switch

One ceiling fan point controlled by one, one way switch and regulator.

One three pin 5 Amps socket outlet point controlled by one No one way switch on same board

One three pin 5 Amps socket outlet point controlled by one No one way switch on independent board

One bell point controlled by one switch

All as per Item No 116 here-in-above but with stranded copper conductor 2.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed multistranded FRLS cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated multistranded FRLS copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

S & F for Switch piano, flush type single pole, one way 5 Amp all as specified.

S & F for Switch piano, flush type single pole, one way 15 Amp complete all as specified.

S & F for Bell push, flush type, 5 amp complete all as specified.

S & F for Bell, AC. 230 volts, single pole complete all as specified.

S & F for Socket outlet 2 in 1, 3 pin, 5A complete all as specified.

S & F for Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type complete all as specified.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified.

S & F for ceiling rose 2/3 terminals, PVC/ polycarbonate, isolated body ISI marked complete all as specified.

S & F for MCB DB, SPN, sheet metal enclosure, 8 way with 200 amps rated bus bar double door, fixed on wall making good to disturbed surfaces, and connecting with cable including taking down old u/s DB with MCB complete all as specified and directed.

All as per item No 127 here-in-before but TPN 4 way.

S & F for MCB double pole of rated capacity 32 amps, 240 volts breaking capacity 10 KA, C-curve complete all as specified.

S & F for MCB Single pole rated capacity 6 to 32 amps, 240 V breaking capacity 10 KA ,C- curve complete all as specified.

S & F for MCB FP of rated capacity 63 amps, 415 volts,50 Hz 10kA, C-curve complete all as specified.

S & F Lamp holder, PVC/Polycarbonate type with back plate including 12 watt LED bulb complete all as specified and directed.

S & F bulkhead luminaries including LED bulb 10W Make Bajaj Cat part No 112334 BIBWP 10W LED or equivalent model from the specified make given in PS including taking dwon old existing light fittings complete all as specified and directed.

Supply and fix LED Tube light fittings wall mounted, 18 W LED 6500K with Opal white Poly Carbonate diffuser provided with high efficient integral constant current LED Driver 230 V etc. complete with mounting batten including all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size from ceiling rose to connector Conforming to Cat Part No. BLRB DB 118 & BLRB18 W CW LED Make :- Bajaj or equivalent model given from the specified make given in PS including taking dwon old existing light fittings complete all as specified and directed.

M & L for Sub main wiring with 2 runs of single core 4 sqmm PVC insulated unsheathed multistranded 1100 volts grade with copper conductor drawn through and including non-metallic rigid 25 mm PVC rigid , ISI marked and its accessories duly PVC conduit in wall/ roof / floor including one run of single core 4 sqmm PVC insulated unsheathed multistranded 1100 volts grade with copper conductor cable as earth continuity conductor along with the wiring and connected from DB to DB/ main board including taking down old u/s submain wiring complete all as specified.

Taking down ceiling fan of any sweep, keeping with safe custody and refixing the same with replacement of unsv 3 core PVC insulated PVC sheathed 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal over hauling the fan complete including spray, painting with one coating of synthetic enamelled paint including filling cavities with filler, one coat after cleaning all dust etc all as specified and as directed.

M & L for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm buried directly in ground earth pit not less than 2.25 m deep below normal ground level, with top edge of the plate vertically to depth of not less than 1.5 m below ground level connected to and incl GI wire 4 mm dia and GI pipe 15 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl RCC cover and MS angle iron frame, watering arrangement with GI pipe 20 mm dia and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete.

Suma Construction

L.T Associate

Parhar Enterprise