SPECIAL REPAIRS TO BLDG NO P 304, P 305 AND SPECIAL REPAIRS TO HARD STANDING NEAR FFTF HARD AT INS SHIVAJI LONAVLA

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L for 75 mm thick PCC (1:3:6) type C 2 (usin 40 mm gradded stone aggregate) as in sub base of flooring etc

Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6

Rendering 10 mm thk in CM (1:4) as in backing coat of cement plaster for laying of wall tiles

M & L for ceramic tiles 8 to 10 mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with surface

M & L for Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with surface

Glazed ceramic tiles in Dado/ Skirting in vertical surface 350x250mmx7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match with surface

Taking down existing doors/windows/ventilators (without taking off shutters and guard bars) of n exe 1.5 sqm complete all as specified and as directed incl stacking the materials properly.

Taking down existing doors/windows/ventilators (without taking off shutters and guard bars) of exe 1.5 sqm & n. exc 4 sqm etc complete all as specified and as directed incl stacking the materials properly.

M&L for powdwer coated aluminium three track, three shutter (of equal width) sliding type window without sash bar including necessary jointing clip, rubber packing, neoprene rubber gasket, locking arrangement (star lock) bearing (two no's for each sliding shutter ) &4 mm thick plain glass for glazing with for two shutters and aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire stapless complete all as specified and directed for one shutter & including following powder coated section as given in 'JINDAL' catalouge complete all as specified and as directed (i) Frame (Bottom) -20620, (ii) Frame top & Side - 20621, (iii) Shutter Vertical (Handle Lock) - 20846, (iv) Shutter Vertical -(int lock) - 20845, (v) Shutter (Top) - 20844, (shutter Bottom) - 20847

S&F aluminium ventilator louvered type without sash bar section as per designation 63400 of IS 737 approved by GE( minium 15 micron anodised) including necessary jointing clip, rubber packing,including necessary locking arrangement , anodised snap beading screws and 4mm thick pin headed glass etc complete

S&F factory made Solid PVC Double door frame of size 50mm x 95mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. tube, supplying & Fixing in opening as directed by EIC

S&F factory made PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube all as specified and as directed.

S&F Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed in 2nd class hard wood

S & F 35mm thick second class hardwood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, with commercial face veneers complete all as specified and as directed.

S & F factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F for 35 mm Factory made Moulded door shutter - Wood free consisting of frame made out of M.S. tube of 19 gauge thickness and size of 25 mm X 25 mm for stiles, top and bottom rails M.S. frame shall have a coat of steel primer. The inner panel shall consist of 25 mm thick High density EPSconforming to IS 4671-1984 bondedwith 2 mm termite proof, water proof and fire resistant molded PVC sheet with 2,4,6 raised panel designs in different plain and / or prelam colours after routing the Moulded design on one side & 2 mm plain and / or prelam PVC sheet on other side of the EPS. The edge of the panel is to be sealed with lipping of 10mm wide PVC sheet baton (made by sticking 2 nos , PVC sheets of 5 mmt thickness using PVC solvent cement ) and stile sides 25 mm (5mm x 5)thick and 30mm wide PVC sheet fitted along M.S tube for lock provision & for lock height 5 mm thick PVC sheet of 150 mm x 100 mm fixed with upper & lower face of inner side of EPS panel and manufacturer's specification & drawing etc, complete all as specified and directed.

All as per Item No 17 above but wire gauzed i.e pannel will be of wire gauze in lieu of single side prelam PVC sheet pannel. The wire gauze shall be wrapped on an addtional square 8 mm MS solid tube and and this tube shall be welded to MS tubes. The wire shall be streched to tighten firmily all as specified and directed

S&F Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165

M&L preparation of new steel surface and applying two coats of synthetic enamel paint ovre a coat of red oxide primer.

M&L for machine cut Granite (of any type) tiles 20-25mm thick for kitchen platform over and including bedded and jointed with grey cement slurry/backing coat 15 mm thick in CM (1:4) and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types

M & L for Machine cut kota stone slab flooring 20-25mm thick for window cill, jambs and sofits over and including cement screed base 20 mm thk in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M & L for Rounding to edges of stone slabs on edge, such as in steps, cooking platform, and other similar situations

S&F Butt hinges, cast ss, with mild steel hinge pin, bright polished and fixed, type B-11

S&F aluminium handles cast type anodised 125mm size.

S&F aluminium anodised barrel tower bolts of extruded section and fixed 200 mm size.

S&F aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of sextruded sections or cast aluminium alloy and fixed 250mm length.

Cutting holes in brick wall built in cement mortor for inserting hold fast and making good the disturbed portion in cement mortor 1:3 depth of embeded portion exc half brick & N.exc one brick.

M&L for hand made sliding bolts; clamps; hold fasts; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe410-0 or Fe 310-0

M&L for Preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint

M&L for preparation of new/ old wooden surfaces by applying two coats of synthetic enamel painting over one coat of pink primer on wooden surfaces exceeding 10 cm width or girth including preparation of new/old surfaces.

Taking up or down steel tubing and connections, 15 mm bore including cleaning for re-fixing or removal to store

Taking up or down steel tubing and connections, 20 mm bore including cleaning for re-fixing or removal to store

Taking up or down steel tubing and connections, 25 mm bore including cleaning for re-fixing or removal to store

S&F Tubes, ‘medium grade’ galvanised, 15 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors

S&F Tubes, ‘medium grade’ galvanised, 20 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors

S&F Tubes, ‘medium grade’ galvanised, 25 mm bore with all fitting and fixed complete to walls and ceilings or laid in floors

S/F in repairs wash hand basin, vitreous china white of size 550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed.

Supply and fix in repair 10 ltr, PVC, valveless, syphonic action type, flushing cistern, low level/ high level including inlet, ball valve, float and handle including brackets with and including PVC flush pipe 32 mm bore, connecting to WC with PVC telescopic pipe complete all as specified and directed.

S &F PVC connections 15 mm size with PTMT nuts of length 450 mm

S & F Bib taps, fancy type chromium plated with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed 15 mm bore

S & F Stop valves, fancy type chromium plated, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed 15mm bore

S&F in repairs vitreous china squatting pan, white, orissa pattern pan of size 580 mm x 440 mm of standard quality with integral foot rests,and including 'P' trap or 'S' Trap complete including connection to trap and to flushing pipe, anti syphonic pipe etc., complete all as specifiedand directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

S&F stainless steel kitchen plate rack of size 90cm X120cm X 1mm thick (18 gauge) in repair, complete all as specified and directed.

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, as in floors or fixed to walls 75 mm bore

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or fixed to walls 110 mm bore

S&F PVC (SWR) bends any radius 75 mm bore

S&F PVC (SWR) bends any radius 110 mm bore

S&F PVC (SWR) junction single, (Single T) equal or unequal 75 mm bore

S&F PVC (SWR) junction single, (Single T) equal or unequal 110 mm bore

S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement diameter of outlet 75 mm

S&F in repair PVC (SWR) `P’ trap 110/110 mm bore

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for rendering 15mm thick in cement mortar 1:4 on brick work or concrete surfaces and finished even and smooth without using extra cement on walls

Supply only integral water proofing compound.

M&L for preparation of old painted surfaces including brooming down or steel wire brushing, scraping down smoke soot, moulds, moss; efflorescent salts & trading oil, greasy spots and applying two coat of lime white wash on the ceiling etc complete all as specified and directed (Rate inclusive of necessary scaffolding, trestels, ladders, cradles etc required for execution of work)

M&L for complete removal of existing treatment of old painted wall surfaces and applying two coats of oil bound distemper over a coat of primer over 3mm thick wall care putty of approved make & shade on walls and other places as directed by Engr-in-Charge. (Rate including the required scaffolding & other accesories required for painting)

M&L for complete removal of existing treatment and applying two coats of anti fungal paint (acrylic base exterior weather proof paint) over a coat of acrylic primer complete all as specified and as directed.

M & L for Preparation of old painted steel surfaces of any description having execcding 10cm width or girth and applying two coat of synthatic enamel paint complete all as specified (Rate inclusive of necessary scaffolding and cradles for hoisting and lowering etc required for execution of work)

S&F aluminium anodised tubular curtain rod, 20mm dia, as fixed in repairs, complete all as specified and directed.

S & F bracket for 20 mm dia tubular curtain rod (for item above )complete all as specified and directed

Completely removing existing water proofing treatment of any descriptions and any type including top layer of plaster / china mosaic wherever occurs over roof and chhajja surfaces and scrubbing the surface with wire brush and cleaning wash down with water to receive new cement plaster / PCC layer and removing the waste material / debris to a distance exc. 1500m but n.exc. 2000m etc complete all as specified and directed by Engr-in-charge.

M/L for rendering 15mm thick in cm 1:4 on concrete roof and chajja surface to get a uniform level surface for laying of membrane treatment .

M/L for applying oil based bituminous primer @ 0.10 Kg/Sqm providing and laying 4mm thick. APP modified water proofing membrane weighing not less than 4kg/sqm re-inforced with non woven polyester matt weighing not less than 160 gm/sqm having softening point not less than 140 degree centigrade longitudinal tensile strength not less than 650 N/Sqm, tearing strength of 180N and with thermal insulation with the mineral / graved finish on upper side and laying with torches application and with 10 cm minimum lap in both direction length wise and width wise all as specified and directed by Engr-in-charge.

Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats . (Minimum weight 190gms)

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate), 100mm thick as in plinth protection, subbase of flooring etc.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry at 3.00 kg cement per sqm completed all as specified and as directed.

M&L for Plain cement concrete work in pavement/hard standing M-20 grade, Type A-1, 1:1 1/2 :3 mix using Ready Mix Concrete (RMC) Using 20mm graded stone aggregates thickness of concrete 25cm or less including necessary use & waste of form work and brooming the top surfaces complete all as specified and as directed.

Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade `A' for depth of slab 150 mm

M&L for reinforced cement concrete (Nominal Mix), M-20 grade (using 20mm graded stone aggregates) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L for use & waste of Formwork to Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping)for fair finished surfaces of concrete flat complete all as specified and as directed.

M&L for TMT bars, 10mm dia & over, cut to length,bent to shape required including cranking and bending spirally for hooping for columns, hooking ends and binding with & including Mild steel wire annealed not less than 0.90mm dia or securing with clips complete all as specified and as directed.

M&L for TMT steel bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for precast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, shelves and similar articles with plain faces, set in CM 1:4, including necessary form work moulds etc all as specified. (Reinforcement shall be measured and paid for separately).

M/S BHASKAR MANIKRAO PAWAR

SAI SAMARTH ENTERPRISES

VIJAYA ENTERPRISES

M/s S.D Construction Co

DWARKESH STRUCT-CON

seema enterprises

RK AND SONS CREATION