SPL REPAIR TO BLDG NO P 4 FAFA, PROVN OF TOILET BLOCK AT EM SUB DIVN AND INTERLOCKING TILES AT 681 TPT UNDER GE (WEST) LUCKNOW

Amount

Demolition of brick work or stone/ boulder masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed. NOTE: Reinforcement shall be cut as required to facilitate demolition.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in, trenches including spreading, levelling, watering and well ramming in layers not exc. 25cm in soft/ loose soil complete all as specified and directed.

Removing surplus excavated material soils n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Labour only for Earth (soil) filling under floors or in foundations including spreading and levelling in layers n exc 25cm thick and well ramming including watering as required complete all as specified and directed. NOTE: Soil obtained from excavation shall be used.

M&L ATT for treating the bottom and sides of excavation @ 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L ATT for treating the top surface of filled earth @ 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L ATT for treating the soil under plinth protection @ 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L post construction ATT for treating along the external wall below concrete or masonary apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in apron complete all as specified and directed.

M&L post construction ATT for treating of soil under existing floors using chemical emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 course sand) to match the existing floors complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge not exc 63mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and directed.

M&L brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other bands, plinth courses, string cources, lacing cources, parapets and railing upto 60cm in hight, copings, kneelers, apex stones, bed plates, water troughs, hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L Mild Steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild Steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild Steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in slab supported on wall, beams and coloumns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and similar works complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span and similar works complete all as specified and directed.

Use and waste of formwork to soffits of suspended slab such as roof slabs, floor slabs, landing and similar work not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splay between floors and beams, etc. and similar works for rough finished surfaces complete all as specified and directed

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizintal or sloping and similar work exc 5cm but not exc 10cm wide and similar works for rough finished surfaces complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area n. exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but n. exc 4sqm each complete all as specified and directed.

S&F pressed steel door frame of size 105x60mm with one or more rebates, made out of 1.25mm thick MS sheets including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and fixed including one shop coat of primer complete all as specified and directed.

S&F pressed steel door frame of size 125x60mm with one or more rebates, made out of 1.25mm thick MS sheets including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and fixed including one shop coat of primer complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, divided into squares, with plain, chamfered or rounded, metred and rebated shash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass, gauge etc sizes of members of shutters as specified in SSR Part-I Section 8 clause 8.24(a) and fitted to chowkats complete all as specified and directed.

S&F flush shutters 30 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F factory made Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, supplying and fixing in opening with fittings as per specification & drawing complete all as specified and directed.

S&F Powder coated anodized aluminium frame for doors, windows, ventilators with one or more rebates using 1.50mm thick aluminium section including joining cleat for fixing etc. complete all as specified and directed.

S&F in repair Powder coated anodized aluminium glazed window and ventilator shutters, side hung/ top hung type without sash bars, with aluminium sections weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as 01 no. 150mm long peg stays, 02 nos. 100mm long hinges type B-21, 01 no. 150mm long tower bolts and 01 no. 125mm long handles including glazed with 5mm thick plain or tinted glass (Make: Modi Guard/ Saint Gobain) complete all as specified and directed.

S&F Solid PVC frame (single rebated) size 60x30mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws complete all as specified and as shown on drawing. NOTE: Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

S&F 28mm thick factory made solid PVC profiled panel door shutter with integral skin as frame & 3mm thick high pressure compact laminate on both sides of approved colour as infill, with ‘C’ type GI or 40x20x19mm of MS pipe as stiffner and fixed in frame at site as per specifications and drawing complete all as specified and directed.

S&F in repair 18/19mm thick factory made solid WPC (Wood polymer composite) flush shutter as in kitchen cabinet made out from co-extruded three layer rigid foam sheet (single extruded) duly prelaminated with 1mm thick both side decorative lamination layer of density 1400 Kg/cum and central core material of density not less than 600 Kg/cum and manufactured by an ISO 9001-2015 certified company and fixed to frame at site as per manufacturer's instruction's including 2mm thick edge bonding tape all around complete all as specified and directed.

S&F 100mm size butt hinges, medium weight, cold rolled, mild steel and fixed with screws complete all as specified and directed.

S&F 150mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 103x64x28mm size auto concealed stainless steel hinge, bright finished suitable for cabinet as per manufacturer's instructions complete all as specified and directed.

S&F 100mm long aluminum anodised, hasp and staple, safety type, with mild steel hinge pin including bolts to hinge plate and fixed with screws complete all as specified and directed.

S&F 150mm long, mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F Ball catches (magnet catcher) with 8mm dia steel ball, brass body and striking plate including letting in, overall size 50x15mm and fixed to shutter complete all as specified and directed.

S&F 40mm dia, cupboards knobs, decorative, fixed with nut, screws and washer of mild steel, bright finished complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Taking down cement or cement lime plaster any description from walls/ceiling etc including racking out joints, hacking for key & scrubbing down with water all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

M&L for rendering 5mm thick in CM 1:3 on fair faces of brick work or concrete surface of ceiling and finished surface even and smooth without using extra cement complete all as specified and directed.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for two coats of oil bound distemper over one coat of primer and 1mm thick layer of wall care putty on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

Complete removal of existing treatment of wall and M&L for two coats of oil bound distemper on previously treated plastered surfaces of wall over one coat of primer and 1mm thick layer of wall care putty including preparation of surfaces complete all as specified and directed.

M&L for two coats of cement base paint over one coat of primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

Complete removal of existing treatment of wall and M&L for two coats of cement base paint over one coat of primer on previously treated plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L for two coats of white wash on old decorated plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood or wood based materials of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel or iron of any description over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, laid in panels, finished surface even and smooth without using extra cement and forming 12mm wide expansion joints to the full depth, and filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' complete all as specified and directed.

M&L Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for joint free glazed ceramic tiles, coloured, superior quality of size 450x350x7mm thick, in vertical surfaces etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L for joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in vertical surfaces etc., set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L 20-25mm thick Machine cut kota stone slab flooring, machine cut and polished as in floor over and including 20mm thick rendering in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing including making moulding/ rounding to edges of stone complete all as specified and directed.

M&L 20-25mm thick Machine cut kota stone slab flooring, machine cut and polished as in vertical surfaces over and including 10mm thick rendering in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing including making moulding/rounding to edges of stone complete all as specified and directed.

M&L 18-20 mm thick granite stone slab, machine cut and polished as in shelves, cooking platform etc., bedded and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone, laid over and including 20mm thick screed bed in cement mortar 1:4, including rubbing, rubbing, grinding, making hole for pipe line and including making sandwitch moulding to edges complete all as specified and directed.

M&L 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub bases of floors and pavings etc. finished even and fair without using extra cement complete all as specified and directed.

M&L for 60mm thick M-35 grade factory made machine pressed precast concrete interlocking paver block of any shape and size conforming to IS 15658-2006 with grey cement and pigment as approved laid over and including 25mm thick sand cushion and joints filled with sand complete all as specified and directed.

M&L for 60mm thick M-35 grade rubber moulded factory made machine pressed precast concrete interlocking paver block using PU mould of any shape and size conforming to IS 15658-2006 with grey cement and pigment as approved laid over and including 25mm thick sand cushion and joints filled with sand complete all as specified and directed.

Cutting chases, pinning in, for concealed water tubing etc. in brick walls and making good to disturbed surface in cement mortar 1:3, cutting not exceeding 10cm in girth complete all as specified and directed.

Taking up or down 15mm bore pipes steel tubing and connections including cleaning for refixing or removing to store or removing from site complete all as specified and directed.

Taking up or down 20mm bore pipes steel tubing and connections including cleaning for refixing or removing to store or removing from site complete all as specified and directed.

S&F 15mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

S&F 20mm bore Steel water tubing 'medium grade', galvanised with all fittings like elbow, tee, socket, bend etc and fixed to wall, ceiling or laid in floors complete all as specified and directed.

Dismantling of water tanks of capacity exc. 250 litres and not exc. 500 litres of any type and in any position and removing from site complete all as specified and directed.

S&F 500 litres capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed suitable for 20mm bore pipe (Min weight 210gms) complete all as specified and directed.

S&F in repair 20mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 20mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F Vitreous China wash down water closet pan, pedestal pattern, white, with 'P' or 'S' trap, excluding flushing cistern but including flush pipe, white seat cover closed pattern including connection to drain pipe (or outgoing pipe) and to flushing pipe etc. and making good to floor complete all as specified and directed.

S&F Vitreous China squatting pan, 'Orissa pattern', size 580x440mm, white, with integral foot rests including PVC 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to trap and flushing pipe etc. and making good to floor complete all as specified and directed.

S&F in repair Vitreous China squatting pan, 'Orissa pattern', size 580x440mm, white, with integral foot rests including PVC 'P' or 'S' trap, excluding flushing cistern but including flush pipe, including connection to trap and flushing pipe etc. and making good to floor complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, low level, flushing cistern of 10 lit capacity, white, with inlet, ball valve, float valve and handle including bracket, rubber cone and flush pipe etc. and connection to pipes complete all as specified and directed.

S&F PVC valveless, syphonic action type, low level, flushing cistern of 10 lit capacity, white, with inlet, ball valve, float valve and handle including bracket, rubber cone and flush pipe etc. and connection to pipes complete all as specified and directed.

S&F in repair vitreous china wash basin, white, flat back type of size 550x400mm including CP waste coupling and 32mm dia waste pipe and fixing of 02 nos brackets made out of 40x40x5mm MS angle iron etc. complete all as specified and directed.

S&F vitreous china wash basin, white, flat back type of size 550x400mm including CP waste coupling and 32mm dia waste pipe and fixing of 02 nos brackets made out of 40x40x5mm MS angle iron etc. complete all as specified and directed

S&F vitreous china urinal, half stall type, white, with grating and union for discharge pipe (excluding flushing cistern and flush pipe), including waste pipe, providing and fixing plugs, bedding urinal against wall etc. complete all as specified and directed.

S&F in repair bib taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed.

S&F bib taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, chromium plated, screwed for iron pipe or for brass ferrule including all accessories complete all as specified and directed.

S&F Pillar taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe including all accessories complete all as specified and directed.

S&F in repair angle valves 15mm bore, half/quarter turn, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F angle valves 15mm bore, half/quarter turn, fancy type, cast copper alloy, chromium plated with long shank and cup screwed down, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair 15mm bore PVC connections, superior quality, with CP brass nuts of length 450mm complete all as specified and directed.

S&F 15mm bore PVC connections, superior quality, with CP brass nuts of length 450mm complete all as specified and directed.

S&F in repair single lever brass CP central hole basin mixer, fancy type with round spout and popup waste system including plugging and fixed, suitable for 15mm bore pipe complete all as specified and directed. Make: Essco Jaquar cat no. TQT516A or Hindware cat no. F280009CP.

S&F in repair brass CP 2in1 wall mixer with over head shower arrangement with arm and long bend pipe, connecting legs and wall flanges, fancy type with costed swinging spout including plugging and securing to walls suitable for 15mm bore pipe complete all as specified and directed. Make: Essco Jaquar cat no. TQT517B or Hindware cat no. F280018CP or Parryware cat no. G3316A1.

S&F in repair brass chromium plated overhead shower rose with arms, 125mm size, round shape, single flow, fancy type, suitable for 15mm bore pipe and fixed complete all as specified and directed.

S&F in repair soap dish, brass chromium plated, oval shaped of size 100x50mm (approx), fixed to wall with PVC gully and CP screws complete all as specified and directed.

S&F chromium plated mild steel jet spray with 1m long PVC flexible pipe, superior quality with bracket and fittings for EWC and fixed complete all as specified and directed.

S&F in repair CP brass tubular towel rail 20mm dia, 'D' type, 600mm long between flanges, superior quality, fancy type, fixed to wall with PVC gully and CP brass screws complete all as specified and directed. Make: Jaquar or Hindware or Parryware.

S&F CP brass tubular towel rail 20mm dia, 'D' type, 600mm long between flanges, superior quality, fancy type, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F in repair 5.5mm thick sheet glass shelf assembly, fancy type, sheet glass shelf of size 600mm long and 120mm wide with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F in repair 5.5mm thick sheet glass corner shelf assembly, fancy type, sheet glass shelf of size 250x250mm, with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F 5.5mm thick sheet glass shelf assembly, fancy type, sheet glass shelf of size 600mm long and 120mm wide with CP bracket guard and railing, fixed to wall with PVC gully and CP brass screws complete all as specified and directed.

S&F in repair peg set of 6, stainless steel, fancy type, with 40mm wide stainless steel strip, fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F in repair 20mm dia stainless steel CP curtain rod, superior quality, with end bracket and end knobs and fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F in repair kitchen sink without drainage board made of stainless steel 1mm thick with plugs, washers, waste coupling and waste pipe, including bedding in cement mortar 1:3 to dwarf wall or fixing cantilever brackets and connecting union to waste pipe, overall size 495mmx420mm with bowl size 410x330x160mm complete all as specified and directed.

S&F in repair stainless steel kitchen plate rack (utensil rack) of size 750x600x250mm, made out of 0.8mm thick stainless steel sheet, approved design and fixed to wall with brass screws and PVC gully including all necessary fittings like nuts and bolts etc complete all as specified and directed.

S&F in repair PTMT grating doom, 100mm dia, standard of any colour, (minimum weight 25 grams) and fixed complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F in repair 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls with PVC clamp complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 110mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) bends of any radius, suitable for 75mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) branch piece, single (single Y), equal or unequal suitable for 110mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F PVC (SWR) branch piece, single (single Y), equal or unequal suitable for 75mm bore PVC pipes, fixed and jointed with solvent complete all as specified and directed.

S&F in repair PVC (SWR) multi floor trap (nahnai trap) with PVC grating including jointing with solvent cement, suitable for 75mm bore PVC pipes complete all as specified and directed.

S&F PVC (SWR) multi floor trap (nahnai trap) with PVC grating including jointing with solvent cement, suitable for 75mm bore PVC pipes complete all as specified and directed.

S&F PVC (SWR) vent cowls suitable for 110mm bore pipes complete all as specified and directed.

S&F PVC (SWR) vent cowls suitable for 75mm bore pipes complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 (using 40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

M&L for 150mm bore salt glazed stoneware drain pipes, complete with collars, laid in trenches and jointed in cement mortar 1:1 as in drains complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in concrete foundation bed to 150mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in bed blocks, roof kerbs or mud stops, rounded or champhered on edges including necessary formwork complete all as specified and directed.

Dismantling of brick tiles or terracing tiles, single layer on roofs complete all as specified and directed.

M&L 10mm thick screed bed or bedding layer in CM 1:4 using 100% coarse sand mixed with 3% integral water proofing compound over roof slab, finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall deemed to be inclusive in quoted unit rate.

M&L for provn of roof treatment with polymeric water proofing membrane all as given below:- (a) Taking down existing water proofing treatment and cleaning of roof surface by washing and rubbing etc. and removing the retrieved material to a distance not exceeding 500m where directed. (b) Applying a coat of bituminous primer conforming to IS: 3384-1986 @ 0.25 Iit/sqm on prepared surface and allowed to dry. (c) Applying and laying 3mm thick APP membrane having non woven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10cm and 15cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3. (d) M&L 40mm thick brick tiles kiln burnt best quality jointed and pointed in CM 1:4 mixed with linseed oil @ 5% by weight of cement over and including 15mm thick screed in CM 1:4 complete all as directed.

All as per item no 137 above but except (d) on vertical surfaces.

M&L for repair to sunken floor slab of WC or bath, area n. exc. 1.50 sqm complete all as given below and directed:- (a) Taking down existing concrete or plaster etc. and cleaning of surface by washing and rubbing etc. and removing the material retrieved to a distance not exc 500m where directed. (b) 40mm thick PCC 1:2:4 type B-1 mixed with Dr Fixit WPC over floor surface and allowed to dry. (c) 15mm thick rendering on all vertical surfaces in CM 1:3 mixed with water proofing chemical PIDIPROOF LW of Dr Pidilite as per manufacturer's instructions and allowed to dry. (d) Fixing of 450mm long 40mm dia GI pipe and sealed with with tape and Dr Fixit sealing compound. (e) Two coat brushing with Dr Fixit and cement slurry (1:1.5) to all around surface including floor and allowed to dry. (f) Filling of loose brick bats incl and levelling and ramming. (g) 40mm thick PCC 1:3:6 type C-1 mixed with Dr Fixit WPC over brick bat surface and make surface fair and even.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

Taking down carefully main switches, DB's, MCB DB's of any way or rating and making good the disturbed surfaces of walls complete all as specified and directed.

M&L for point wiring complete for one light point or one fan point controlled by one, one way 5 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including pressed steel concealed terminal switch boxes not less than 1.6mm thick of reqd size factory made duly painted inside and outside with one coat red oxide primer, 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified and directed.

All as per item no 142 above but for one 5 pin 5 Amp socket outlet point on an independent board.

All as per item no 142 above but for one 5 pin 5 Amp socket outlet point on the same board with other switch.

All as per item No. 142 above but for One bell/ buzzer point on an independent board controlled by one bell push

All as per item no 142 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm and green colour earth cable of size 2.50sqmm.

S&F Switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way 15/16 Amp 230 Volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 5/6 Amp, 230 volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 15/16 Amp, 230 volts complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed.

S&F Lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F bell push, flush type, single pole, one way 5/6 Amp, 230 volt flush type complete all as specified and directed.

S&F in repair call bell, ding dong type, AC single pole, 230 volt complete all as specified and directed.

S&F sheet metal enclosure for VTPN DB double door type, 4 way, suitable for 4 pole MCCB, 415Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCCB/ MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 12 way, 240Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F MCB, single pole 6 to 32 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, single pole & neutral 40 to 63 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCCB, 63 Amp, 4 pole, 415 volts, 16 KA breaking capacity complete all as specified and directed.

Supply and fixing modular type AC box with socket plug top and MCBs with two pin and one pin for earth plug and socket complete with one single pole MCB 20 Amp complete all as specified. Make: ABB/Havells/C & S.

S&F ceiling fan regulator, electronic, rotary step up socket type, 230 volts suitable for 1200/1400 mm sweep ceiling fan including necessary connection complete all as specified and directed.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4sqmm nominal cross sectional area and one run of 4sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 6sqmm nominal cross sectional area and one run of 6sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F in repair wall mounted 20/22 W LED integrated tube light fitting, 1200mm long batten with extruded aluminium housing, frosted diffuser and integrated electronic driver with decorative end cap complete and one no 20/22 W LED 6000K, 230V, tube light complete with all required fittings and fixtures arrangement including and provn of connection from ceiling rose to luminaries with PVC 3 core flexible copper wire complete all as specified and directed. Make: Havells Endura Linear Neo cat no. BS 22WLED865SPCWH or Philips smart brite cat no. BN 021LED 22S6500/4000 PSU GR/SI or Bajaj cat no. BCLAB 20W WH LED P.

Supply and fixing wall/surface mounting luminaires (Mirror Light) integrated LED Batten( 2 feet) 10/12 W, 6500 K, 230V ,100 lumens/watt,with extruded aluminium housing & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements all as per specified and directed by Engr-in-charge.Make:Phillips smart brite cat no BN 021 LED 12S 6500/4000 PSU GR/SI or/Havells Endura linear neo cat no enduralinear neo BS10WLED865SPCWH/ HPL Neptune plus 10 w HLPT51510CW

S&F in repair LED bulk head light fitting, made of cast aluminium body with heat resistance pressure, die cast housing, IP-65 protection cover and one no. 7/10W LED, 6000K, 105 lm/watt with inbuilt electronic driver including and provn of connection from ceiling rose to luminaries with suitable size copper wire complete all as specified and directed. Make: Philips (Vista Glow) cat no. WT140W LED7S NW PSU S1 PC or C&S Cirius series cat no. LTB10W LED or Havells cat no. HEXAFT 10WLED857SSYMBOPC or Bajaj wee plus cat no. BIBWP 6WLED.

S&F in repair LED Building security light 24/25 Watt with high power LED source (>110lumen/watt) PDC housing, IP65 and IK 07 with 4 KV inbuilt surge protection potted driver including Electrical connection with PVC three core copper flexible wire & all necessary fixing accessories such as bracket of GI pipe light grade 40 mm dia 0.60 mtr long bend to shape as per suitable size along with all accessories, fixed on wall including bolts & nuts. Make philips Green line smart cat noBRP042 LED 25 CW R1 S1 PSU GR/ Bajaj Edge nxt LED cat no ENXT P 24L WH CR PC SD/ Eveready Mini might cat no LED SL025157-02

S&F in repair decorative wall light fittings made out of brushed nickel finished with opal glass diffuser, (Spiral B-22 base) with 01 No. 9 W LED Bulb, 6000K, 230V complete including required fixing arrangements complete all as specified and directed. Make: Havells decorative florentine WL 1LS B22 SS PPCP cat no. LHFOAJE1TN1 060 or Philips model Grace or equivalent in Bajaj.

S&F in replacement LED lamp 9 W, B-22 base, 6000K complete all as specified and directed.Make : Philips/CG/Havells/HPL

M&L Earthing complete with galvanised steel earth plate electrode 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m deep below normal ground level, connected to galvanised earth lead wire 4.0mm dia (7.50m) by means of bolts, nuts, check nuts & washers of galvanised iron or steel, earth lead wire protected by 15mm dia GI pipe light grade, 20mm dia light grade GI pipe for watering, meshed funnel, alternate layer of charcoal and common salt complete all as SSR Item No. 19471 and shown in electrical plate No. 3 of SSR part-I with PCC chamber, 50mm thick RCC cover in 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 8mm dia TMT bar @ 80mm c/c both way in lieu of CI pit cover and protection including necessary excavation and earth work complete all as specified and directed.

Taking down carefully electric meter of any capacity from wall or any position by disconnecting all connection and refixing the same including all electric connection and acessories as required including teak wood board of suitable size complete all as specified and directed.

Taking down carefully ceiling fan/ exhaust fan by disconnecting all electrical connection complete all as specified and directed. NOTE: Old ceiling fan/ exhaust fan shall be deposited to E/M store yard

S & F of ceiling fan 1200 mm sweep, BEE star rated (40-48 Watt), Min air delivery 215 CFM, copper wound motor, AC single phase, 230/240 volt, white colour complete with blades, down rod 300mm long, canopy and provn of connection with 3 core flexible copper cable of size 1.5 sqmm from ceiling rose to fan complete all as specified and directed. Make:- Havells ES 40 /Usha Technix plus/Orient energy star

S&F heavy duty metal body exhaust fan 300mm sweep, copper wound, 1400 RPM, AC single phase, 230/240 volts, fancy type complete with fan motor, blade, bracket, ring and louvers including and provn of grouting 4 nos anchor bolts with nut and washer and making good to disturbed surfaces to match the existing and provn of connection with with three core flexible copper wire cable of size 1.50sqmm from ceiling rose to fan complete all as specified and directed. Make: Orient (Heavy duty)/ Usha (Turbo heavy duty metal body)/ Havells (Turbo Force HP)/ Khaitan (heavy duty metal body). NOTE: Old unserviceable fan shall be deposited to EM store yard.

S&F Exhaust fan made out of sturdy engineering plastic body, 200/230mm sweep, 1200RPM, AC single phase, 230/240 volts, fancy type complete with fan motor, blade, bracket and ring complete all as specified and directed. Make: Orient/ Khaitan/ Usha/ Havells/Almonard.

Cutting and opening of circular holes in shape in one brick thick walls built in cement mortar for fixing of exhaust fan up to 300mm dia and making good dismantled portion in CM 1:3 or PCC 1:2:4 type B-1 using 20mm graded stone aggregate including and provn of fixing of 4 nos anchor bolts with nut and washer to fix the exhaust fan complete all as specified and directed.

S & F water heater storage type electric BEE five star rated of capacity 25 ltrs to operate on 230 volt AC, 2000 watt vertical type including 2/4 Nos full threaded fastener of size 100x10 mm with, 2 No washer, water connection with 02 Nos heavy duty PVC flexible pipe of size 15 mm, 450 mm length & suitable plug top of 16 Amp capacity complete all as specified and directed. Usha Misty/Racold CDR DLX/Bajaj Montage/Havells monja DX Note : Product must have 2 years warranty, 2 years warranty on heating element & 5 years warranty on inner tank.

EVEREST CONSTRUCTION

R K CONTRACTOR AND SUPPLIERS

M/s Chandra Mohan and Sons

M/S S S A ASSOCIATES

M/s Pratap Associates

M/S Reliance Construction

M/s Sachkhand Traders