PROVN OF OVERHEAD CONDUCTOR LED LIGHT SERVO VOLTAGE STABLIZER SUBMERSIBLE PUMPSET CEILING FANS WALL MOUNTING FANS EXHAUST FANS DESERT COOLER ETC AT BD BARI MIL STN UNDER GE KALUCHAK

Amount

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out in any type of soil for water supply pipe line, foundation of pole, stay, taking up or laying of cable etc complete all as specified & directed. Note : Due care shall be taken while deciding cable route for excavation. However any damage to Signal, BSNL, MES cable water/sewage pipe or any other service while excavation will be made good by the contractor and cost of the same for jointing material & labour is deemed to be included in the cost of excavation.

Excavation in trenches n.exc 1.5 mtr wide exc 1.5 mtr in deep but not exceeding 3.0 mtr deep and getting out for foundation of poles etc. in any type of soil, complete all as specified & directed. Note : Due care shall be taken while deciding cable route for excavation. However any damage to Signal, BSNL, MES cable water/sewage pipe or any other service while excavation will be made good by the contractor and cost of the same for jointing material & labour is deemed to be included the cost of excavation.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm, complete all as specifed & directed.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified & directed.

Sand cushioning to under ground cable, laid in trenches 8cm thick below the cable and 15cm thick above the cable after laying and stretching the cable complete punned to 18cm, complete all as specified and directed. Note:- Punned thickness of sand will be measured and paid.

Brick well burnt locally available sub class 'B' laid over sand cushioning for mechanical cable protection in trenches with width of brick perpendicular to the length of cable, complete all as specified & directed.

PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in foundation of poles etc including necessary form work, complete all as specified & directed.

PCC 1:3:6 type C2 using 40mm graded crushed stone aggregate as in stay etc including necessary form work, complete all as specified & directed.

PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in coping of pole etc including necessary form work, complete all as specified & directed.

XLPE insulated, armoured heavy duty electric cable (heavy duty) with aluminium conductor, 1100 volts grade, cross-sectional area 70 Sqmm 3.5 core connected with suitable cable gland and aluminium lugs, laid in trenches or passing through pipes including testing after completion and removal of old unserviceable cable, complete all as specified and directed. (Earth work, brick protection and sand cushioning shall be measured and paid for separately)

Cable jointing kit for LT 1100 volt grade cable for indoor termination heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 70 sqmm including testing and commissioning, complete all as specified & directed.

Structural steel work as in cross arms, bracings, supports, clamp and back plate fabricated from steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed by Engineer-in-Charge and applying two coats of aluminium paint over one coat of red oxide zinc chrome primer after preparation of surfaces, complete all as specified & directed.

Pin type insulator porcelain, vitreous, white/brown or green including one galvanized mild steel spindle, two galvanized iron washers and one galvanized iron nut, 65mm dia and 100mm height for working pressure 1100 volts grade, complete all as specified & directed.

Shackle type insulator porcelain vitreous white, brown or green 75mm high and 90mm dia for conductor of working pressure 1100 volts including galvanised mild steel straps of 31x5mm size, 14mm dia insulator bolts, washers and nuts, complete all as specified & directed.

Aluminium conductor steel reinforced conductor of any size drawn straight horizontal on over head lines on existing poles including binding with insulators, streching without kinks and bends winding wire etc, complete all as specified & directed.

Stay assembly with accessories as shown in Electric Plate No 1 of SSR Part-I 2009 such as 14mm dia 400mm long galvanised stay bow, galvanized steel stay rod 20mm dia 1800 long, mild steel galvanised steel plate 300x300x6mm, galvanized thimble, etc, complete all as specified and directed. Note: Excavation, PCC stay strands and loop type insulator shall be measured and paid for separately under respective items.

Loop type insulator, porcelain, vitreous white/ brown or green, large size with overall dimensions 90x140mm clearance of hole 25.5mm, complete all as specified & directed.

Galvanised stay strand wire of size 7/4.00 mm all as required at site or shown in electrical plate No 1 of SSR 2009 Part-I, complete all as specified & directed.

Steel tubular swaged poles in vertical position swaged type 410-SP-31, 9 Mtr long, ISI marked complete with cast iron base plate, finial taper plug, bolts, nuts washers and screws as required duly painted with two coats of aluminium paint over a coat of red oxide primer above ground level including painting throughout internally & below GL (externally) with two coats of bituminous paint, numbering of poles with cut stencil lettering in size 6mm thick and 50mm high and yellow and black strips of size 30cm width each with synthetic elamel paint upto 1.5m above coping etc including taking out /dismantling of old unserviceable poles, complete all as specified and directed. Note:- 1. Earth work and PCC will be measured and paid seperately under appropriate items.

Earthing complete with galvanized mild steel earth plate electrode size 600mm x 600mm x 6mm thick buried directly in ground (preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 3 meter (BGL), connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore 'light grade' galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt etc including connected to test point and testing on completion, complete all as shown in electrical plate No 3 of SSR Part-I 2009 & as directed.

Galvanised iron tube 40mm bore light grade (ISI marked) for cable protection to poles/under floor/under roads/alongwith walls complete including MS clamps of flat iron 25x3mm duly painted, GI nuts, bolts and washers & sealing of pipe ends with approved sealing compound, complete all as specified and directed.

Supplying, installing, designing, testing and commissioning of LT outdoor type feeder piller box canopy type (Cubical Kiosk Feeder Pillar Box), weather, dust and vermin proof, with IP-54 as per IS-13947 protection, fault rating 50 KA /1Sec, factory made, CPRI approved with locking arrangement, made out of CRCA sheet 3.15 mm thick with angle iron frame of size 50x50x6 mm cubical type complete with 100 amps rated copper bus bar of size of appropriate size with cable gland of suitable size and in adequate nos, cabinet for housing mounting switch, disconnection fuse unit, metering equipments, prewired with suitable size of copper conductor and duly powder coated

mounted on PCC platform, excavation in trenches including PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate, size of PCC (2 metre length x 0.30 metre in width and 0.90 metre in depth (0.45 metre above ground and 0.45 metre below ground level) including necessary formwork etc, panel legs made out of 50x50x6mm thick angle iron (4 legs each 0.60mtr duly embedded in PCC duly marked incoming and outgoing cables, continuous GI earth strip 32x6mm for earthing of panel, complete all as specified, directed and comprising of the followings:-

Cable junction box, IP-66 insulated made out of PC-GFS polycarbonate, black colour (RAL 9011), environment friendly, recyclable, weatherproof (UV due to solar radiation, protected against rain water, temperature resistant), halogen & silicon free, anti-acid, anti-corrosive for outdoor installation of street light of size 225mm x 295mm x 122mm fixed on pole complete with links/terminals suitable for in/out XLPE cable size upto 35sqmm 3.5 core including MCB SP 6 Amps,10KA including necessary flat iron clamps with nuts, bolts & washers for fixing on pole, complete all as specified & directed. Make. Hensel-Cat Part No.KF3500B of equivalent in Schneider/ Rittal/ GE

Intergral LED street light luminaries 90W LED, 230 volts, aesthetically designed roadway luminiare with excellent thermal management, mounted on & providing 40mm GI bracket with necessary MS clamps, nuts, bolts, washers etc including making connection with PVC copper conductor cable of appropriate size, complete all as specified & directed. Make. Crompton Greaves : Cat Part No. LSTN-90-CDL-A / C&S Electric : Cat Part No. LTESS90WLED/LS / Halonix : Cat Part No.HLSLD-10-90-WWL-S/ Philips : Cat part No.BRP410LED094CWHEMRFGS2PSUGR

Supply, installation, commissioning and testing of OEM manufactured APFC Panel indoor type fabricated out of 2mm thick CRCA sheet and having four nos angle iron legs made out of 50x50x6mm thick, 60cm in length (each) with 7% Aluminium reactor of capacity 30KVAR (output) @440V, AC supply, stage rating shall be 4x5KVAR+1x10KVAR, fully type tested at an independent laboratory, comply with IEC 61439-1&2 and IEC61921,IS-16636-2017, degree of protection - IP54 in accordance with IEC 60529, capacitor bank shall be internet of things (IoT) enabled and communicable / integrable with BMS, indoor type confirming to IS13341:1992 & IS13440:1993 floor mounted design, weather, dust and vermin proof suitable for humidity upto 95%. average daily temperature +35 degree celsius, ambient temperature 5 to 40 degree celsius, maximum altitude 2000 metre shall have suitable doors with locking arrangement, panel, components prewired with copper cables as per manufacturers design, painted with siemens grey epoxy powder coating after suitable chemical treatment, legs embedded in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate, complete all as specified & directed.

Make of Panel : ABB/ Schneider/ Siemens/ L&T The OEM’s specified cannot authorize any other partners/ sub vendors to manufacture APFC Panels on their behalf. The APFC Panel manufactured by OEM only will be accepted & factory acceptance test (FAT) will be carried out at OEM’s plant only. The APFC Panel shall be comprising of the followings :- A) Insulated busbar pan assembly made of aluminium and rated of 200 Amps capacity. The short circuit capacity shall be 50KA/1sec for the main bus bar and the rated impulse withstand voltage shall be 6KV. (B) The incomer of the APFC panel shall be 100 Amps, MCCB, 3P, 50KA TMD type with O/L & S/C protection, Ics=100% Icu.MCCB shall have standard extended rotary handle , spreaders, phase barrier. MCCB shall be of certified design confirming to IEC 60947-1,2&3. Make : ABB/ Schneider/ Siemens/ L&T

(C) Capacitor Units : The capacitor units shall be metalized polypropylene film with Zn/Al alloy. The capacitor shall be encapsulated in an aluminium can. The capacitor unit shall have a rated voltage of 480volts and shall have a maximum overcurrent capacity of 2.5 In.The capacitor unit shall have a built in 3 phase over pressure protection and shall have discharge resistors (50V in 1min) factory fitted and shall be tamper proof capacitance tolerance -5% to 10% maximum permissible overvoltage 1.1xUn,8h every 24h.The capacitor unit shall be of certified design confirming to IS-13340-1993,13341-1992 & IEC-60831-1&2. Make : ABB/ Schneider/ Siemens/ L&T

(D) Short Circuit and Overload Protection : Each stage of the APFC Panel shall have a suitably rated MCCB for short circuit and overload protection. The overcurrent setting shall be adjustable & breaking capacity Ics=>36KA.The MCCB shall be of certified design confirming to IEC 60947-1,2&3. The detuned reactor (Aluminium wound) should be equipped with thermal switch inside the winding which should cut off the respective contactor in case of over temperature. Tolerance of reactors shall not exceed +/-3% of rated value. Make : ABB/ Schneider/ Siemens/ L&T (E) Power Factor Regulator /APFC Relay : Advanced range power factor regulator /micro processor based APFC relay having 6 steps with a LCD display, voltage range 90V to 550V, 50/60Hz, CT input: 1A/5A with a built in RS 485 communication port. The Power factor regulator shall be of certified design confirming to IEC 61326. Make : ABB/ Schneider/ Siemens/ L&T

(F) Stage Contactor :The capacitor duty contactors shall be rated for 230 volts AC and shall be 3 pole type and shall be employed for switchinh ON and OFF operations in capacitors banks. The Contactor shall be AC 3 duty type. The contactor shall be of certified design confirming to IEC60947-1&4-1. Make : ABB/ Schneider/ Siemens/ L&T (G) Reactors : Harmonics block reactors aluminium wound with 7% filtering factor shall be connected in series with each capacitor stage and shall be of iron core type. The reactor should be equipped with thermal switch inside the winding which should cutoff the respective contactors in case of over temperature. Tolerance of reactors shall not exceed +/-3% of rated value. The reactors shall be of certified design confirming to IEC:60076-6 Make : ABB/ Schneider/ Siemens/ L&T

(H) Ventilating fans of required size shall be used to dissipate the heat produced by the capacitor banks components like the capacitor units reactors, contactors , breakers etc. The capacitor bank should be of type tested design and temperature rise test report of the capacitor bank performed at an independent laboratory should be submitted alongwith the offer. Note: APFC panel described as above complete in all respect as per specifications enclosed, upto the entire satisfaction of Accepting officer to ensure safety, reliability and accountability of component coordination, all the major capacitor banks, components such as capacitor units, detuning reactors, PF controllers, circuit breakers, contactors and the enclosure system called for in this specifications should preferably be from a single manufacturer. The OEM shall preferably manufacturer PFC components and switchgears.

Supply, installation, commissioning and testing of servo controlled Voltage Stabiliser fully automatic operation, unbalanced input /output load, three phase (copper wound), 50Hz, naturally oil cooled, indoor type & designed for input variation between 340 volts to 460 volts with output voltage stabilised at 415 volt with accuracy ± 1.0% and speed of correction 8 volts per second of capacity 50 KVA including first filling of transformer oil having dielectric strength not less than 50 KV as per IS:335, 0-500 volts voltmeter, arrangment to check input voltage and output voltage, RYB indication lamp, high & low voltage cut off system, single phase preventor, time delay relay, servo byepass switch, overload & short circuit trip system, ammeter etc., complete all as specified & directed. Make. AE - Model :Type EMS 12-3/1 or equivalent in Brentford/ V-Guard/ Aplab, Andrew Yule

Cable jointing kit for LT 1100 volt grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 70 sqmm including testing and commissioning, complete all as specified & directed.

Earthing complete with galvanized mild steel earth plate electrode size 600mm x 600mm x 6mm thick buried directly in ground (preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 3 meter (BGL), connected to galvanized iron earth strip 32x6mm size by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 50mm bore 'light grade' galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt etc including connected to test point and testing on completion, complete all as shown in electrical plate No 3 of SSR Part-I 2009 & as directed.

Intergral LED street light luminaries 60W LED, 230 volts, aesthetically designed roadway luminiare with excellent thermal management, mounted on GI bracket including GI bracket made out of 50mm bore medium grade pipe of 1.50m length, bent to required shape, fixed on PCC/Steel pole with 02 Nos. clamps of flat iron (40 x 6mm), nuts, bolts and washers duly painted with two coats of aluminium paint over a coat of red oxide zinc chrome primer and making connection with PVC copper conductor cable of appropriate size, complete all as specified & directed. Make. Crompton Greaves : Cat Part No. LSTP-60-CDL / C&S Electric : Cat Part No.LTESS60WLED/LS/ Halonix : Cat Part No.HLSLD-10-60-CWL-I

PVC insulated weather proof flat twin core 2.50 sqmm (nominal area) aluminium conductor cable, 1100 volts grade from junction box to street light fittings, complete all as specified & directed.

XLPE insulated, armoured heavy duty electric cable (heavy duty) with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm 2 core connected with suitable cable gland and aluminium lugs, laid in trenches or passing through pipes including testing after completion and removal of old unserviceable cable, complete all as specified and directed. (Earth work, brick protection and sand cushioning shall be measured and paid for separately)

Rigid non-metallic PVC conduit of 25mm dia, 2.0 mm wall thickness (ISI marked) exclusive of boxes (junction/terminal) but inclusive of fittings such as tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc, complete all as specified & directed.

Supply, installation, testing & commissioning of submersible pump set, multistage (as per mfg design stage) electric driven of capacity not less than 720 LPM, 86 mtr head, water lubricated suitable for 200/250mm bore & 100mm bore discharge pipe coupled with squirrel cage induction electric motor, 3 phase, 415 volts of capacity not less than 20 HP having CI casing & gun metal impeller fitted with delivery pipe etc as required at site, complete all as specified & directed. Make of Pump and Motar : Kirloskar-Cat Part No.KS6F-2013 or equivalent in Crompton/ KSB

Supply, installation, testing & commissioning of submersible pump set, multistage (as per mfg design stage) electric driven of capacity not less than 600 LPM, 73 mtr head, water lubricated suitable for 200/250mm bore & 100mm bore discharge pipe coupled with squirrel cage induction electric motor, 3 phase, 415 volts of capacity not less than 15 HP having CI casing & gun metal impeller fitted with delivery pipe etc as required at site, complete all as specified & directed. Make of Pump and Motar : Kirloskar-Cat Part No.KS6D-1512 or equivalent in Crompton/ KSB

Fully automatic Star Delta Starter motor, motor rating AC-3 duty, 415V, 50 Hz, 3 phase suitable for motor capacity 20 HP relay range 28 - 42 amps having essential motor protection against over loading, single phasing, phase sequence reversal, abnormality in supply, unbalanced current complete all as specified & directed MAKE : L&T Cat Part No. SS95975 or equivalent in Schneider/ Siemens/ ABB

Supply, installation, testing & commissioning of submersible pump set, multistage (as per mfg design stage) electric driven of capacity not less than 1200 LPM, 90 mtr head, water lubricated suitable for 200/250mm bore & 100mm bore discharge pipe coupled with squirrel cage induction electric motor, 3 phase, 415 volts of capacity not less than 35 HP having CI casing & gun metal impeller fitted with delivery pipe etc as required at site, complete all as specified & directed. Make of Pump and Motar : Kirloskar-Cat Part No.KS8A-3505 or equivalent in Crompton/ KSB

Galvanized iron water tubing, medium grade, 20mm bore, screwed & socket joints with all fittings such as sockets, bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc., laid in trenches including clamps connection, cutting, screwing, drilling etc, complete all as specified and directed. Note : (a) Excavation & earth work shall be mesaured & paid for seperately under respective items. (b) Unions of suitable size will be provided at all branches, tee joints at a maximum distance of 30M of straight pipe and its cost are deemed to be included in the quoted rates for this item.

Stop valves, cast copper alloy, 20mm bore, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., fixed in repairs, complete all as specifed & directed.

Cutting & screwing of existing water supply line of any size for alterations or additions (or lengthening screw on pipe to form connector) including testing after completion, complete all as specified & directed.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 1.5 Sqmm drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required, terminated in CI/MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one light/fan point controlled by one way switch using proper colour coding, complete all as specified & directed.

All as per Srl item No. 40 here-in-before but for one 3/5 pin 5 Amps socket outlet on independent board.

Switch piano flush type 5 Amps 240 Volt, single pole one way, complete all as specified & directed.

Switch socket combination, two in one, 5 pin type, 5 Amp, flush type universal, 240 volt, complete all as specified & directed.

Ceiling rose surface type, bakelite 65mmx50mm, 3 terminals, 240 Volt, complete all as specified & directed.

Energy effecient heavy duty Exhaust fan with louvers of size 450mm sweep, 1400 RPM, 230 volts, 50 Hz, single phase, silent type, totally enclosed complete with nuts, bolts & washers including provision of three core flexiable copper cord of size 0.75 sqmm 3 core of required length from ceiling rose or connector to exhaust fan for connection, complete all as specified & directed. Make. Havells, Cat Part No.Turbo Force SP or equivalent model of make specified in List of Makes/ Manufacturers/ Producers here-in-after.

Evaporative air/desert cooler (GI coated metal body not less than 16 gauge), 230volts, 50Hz, single phase, cooler complete with fan of dia 18 inch with motor 1440 RPM, single phase with speed control with three position (low/ medium/ high) motor, fitted with water proof cooler pump of sufficient pumping height and delivery to keep the filter in moist condition, complete with filterpads fitted with non decaying filter material, capable for cooling not less than 2250 cubic feet, overall dimension of the cooler shall not be less than 600mm width (measured along discharged grill side), 900mm height and 600mm in depth, cooler tank capacity 60 ltrs, internally prewired and including back filling arrangement and with connecting cord 3x2.5 sqmm copper flexible cable of 2.5 mtrs length fitted with 3 pin moulded plug top (ISI marked) of 5/6Amp, complete all as specified & directed. Make :Bajaj/ Usha/ Khaitan

Energy effecient heavy duty Exhaust fan with louvers of size 300mm sweep, 1400 RPM, 230 volts, 50 Hz, single phase, silent type, totally enclosed complete with nuts, bolts & washers including provision of three core flexiable copper cord of size 0.75 sqmm 3 core of required length from ceiling rose or connector to exhaust fan for connection, complete all as specified & directed. Make. Havells, Cat Part No.Turbo Force SP or equivalent model of make specified in List of Makes/ Manufacturers/ Producers here-in-after.

Energy effecient heavy duty Exhaust fan with louvers of size 380mm sweep, 1400 RPM, 230 volts, 50 Hz, single phase, silent type, totally enclosed complete with nuts, bolts & washers including provision of three core flexiable copper cord of size 0.75 sqmm 3 core of required length from ceiling rose or connector to exhaust fan for connection, complete all as specified & directed. Make. Havells, Cat Part No.Turbo Force SP or equivalent model of make specified in List of Makes/ Manufacturers/ Producers here-in-after.

Cutting holes in existing brick walls for making opening for fixing of exhaust fan of any sweep including grounting bolts/nuts and making good disturbed surface of walls using cement sand mortar 1:4, complete all as specified & directed.

Wall mounting fan, 400mm sweep complete with accessories AC, 230 volts, single phase, high air delivery even at low voltages, superior ball bearing, low power consumption, complete all as specified & directed. Make. Havells, Cat Part No.Platina HS or equivalent model of make specified in List of Makes/ Manufacturers/ Producers here-in-after.

MCB, single pole & neutral, 6 to 32 Amp, AC, 10 KA repturing capacity, 240 Volt, 'C' series, complete all as specified & directed.

Supply, hanging and testing of BEE 5 star rated super energy efficient ceiling fan with double ball bearing, 1200mm (48 inch) sweep having 3 blades, down rod, canopies, shackles, 230volt, single phase suitable for input voltage range 140-285 volt AC, 50Hz with power factor not less than 0.99, service value minimum 8 cu metre/min/watt or higher, air delivery minimum 230 cu metre/min or more power consumption maximum 28 watt or lower, top speed minimum 340 RPM or higher, THD not more than 10%,speed control by 5 step electronic regulator with three years on site warranty, copper winding complete as per IS:374-1979 or latest IE rule & site requirement, colour white, complete all as specified & directed.

kailu construction co

Sarbat Construction Co

Vishesh Engineers

M/S RAJ ENGINEERS

M/s Ravinder Kapoor Engineers and Builders

SATISH AND CO

ANIKET TRADERS

M/S ASHOK KUMAR SURI