Special repair to Bldg No. P-83 and P-138 (MI Room) and T-271, T-272, T-140 and T-141 in furniture yard at Military Station Fazilka.

Amount

Taking down chowkats or frames with shutters (with out taking off shutters from the frame) not exceeding 1.50 Sqm each all as specified .

Taking down chowkhats or frames with shutters without taking off shutters from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each and all as specified .

Taking down and refixing of alum window shutters of any size in same opening incl repairs /replacement of rubber packing,glass,glazing clips & aluminium section etc (The item glass,glazing clips & alum section will be measured seperately)

Taking down aluminium door shutter ,Refixing of shutters of any size in same opening incl repairs / replacement of rubber packing,glass,glazing clips & aluminium section etc after tightening of members, adjusting of door closure etc. complete all as specified and directed (The item glass,glazing clips & alum section will be measured seperately)

S&F in repairs door closer hydraulically regulated, aluminium (Die cast) body, designation No. 3, universal type suitable for door shutter upto 1000mm in width complete all as specified and as directed.

M&L in repairs Aluminium Motrice lock 4 levers and 75mm size for aluminium doors

S & F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M S square tubes , S&F in opening as per specification & drawing given in SSR-2009.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M S tubes for top & bottom rails M S frame shall be covered with heat moulded plain colour PVC ‘c’ channel having a PVC sheet strip of 20 mm width struck in side with solvent cement for stiles and plain colour PVC sheets 5 mm thick for top rail, lock rail & bottom rail on either side & as gap insert for tap rail & bottom rail, paneling of plain colour PVC sheets to be fitted in the MS frame walded/sealed to the stiles & rails with suitable PVC sheet beading and joined to getger with solvent cement supplying & filling in the frame at site as per specification & drawing given in SSR-2009.

S & F Alum handle cast type anodized 150 mm long all as specified.

S & F Alum anodized barrel tower bolt of extended section and fixed 200 mm long.

S & F 100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinges pin,anodised and fixed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of Frame size 65x 125 mm fabricated with miter joints after applying PVC solvent cement and screwed with fullbody threaded star headed SS screws ,resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of Frame size 45x70mm fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws ,resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life)

M&L Cement concrete 1:2:4 type B-1 for filling of pressed steel fram and hold fast blocks etc all as specified .

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick having minimum density of 650 kg/cum resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge

S&F 18mm thick PVC sheet having one side decorative laminated sheet all required brackets SS screws etc. the panel shall be fabricated using adhesive and screws where ever required.all the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification including fitting i.e. magnetic catcher,stainless steel handle approved by Engineer -in-Charge.

S & F continous piano hinges mild steel bright finish or galvanised of 30mm width

S&F 125mm Hasp and staple, aluminium anodized, including bolt to hinge plate and fixed with screws

S & F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats all as specified .

S & F Aluminium alloy, anodised, sliding door bolt 300mm with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

M & L for preparation of old painted wooden surfaces of any description over 10 cm width of girth not otherwise described and applying one coat of synthetic enamel paint all as specified .

M & L for preparation of old painted steel surfaces of any description over 10 cm width of girth not otherwise described and applying one coat of synthetic enamel paint all as specified .

S & F galvanised mild steel wire cloth, 0.51 mm to 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, or galvanised wire staples,fixed in repairs all as specified .

Taking down cement plaster/dado on brick wall including racking out joints, hacking for keys scrubbing down with water all as specified .

M & L for rendering 15mm thick on fair faces of brick work in cement mortar 1:6 finished even & smooth without using extra cement.

M & L for rendering 15mm thick on fair faces of brick work in cement mortar 1:4 finished even & smooth without using extra cement.

M&L rendering 10 mm thick in cement mortar 1:4 om fair faces of concrete surfaces of ceiling finishing even and smooth without using extra cement.

Supply only liqid water proofing compound.

Dismentling floor, hearth or wall tiling including cement mortar bedding (but not backing), remving serviceable tiles to stores and and rubbish off the permises.

M&L glazed ceramic coloured tiles, (350x450)x7mm thick as in vertical surfaces like dado or skirting over 10mm thick in CM 1:4 set & joined in neat cement slurry and pointed in coloured cement to match complete all as specified.

M & L vitrified ceramic light shade coloured tiles with matt finish,(with highlighted border pattern) 10 mm thick ( square/ rectangular ) polished, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement paste pigmented to tile shade over and including 15mm thick cement and sand screed (1:4) complete all as specified and directed by Engineer - in - Charge.

M&L Non skid ceramic coloured /printed tiles 400*400* 7 to 8 mm thick( square /rectangular) and shall be jointed in neat cement slurry and pointed in paste pigmented to tile shade over and incl 15 mm th screed bed in CM 1:6 complete all as specified and directed by Engr in Charge.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

M&L Granite (of any type) tiles18- 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 20mm thick screed bed in CM 1:4, finished even and smooth without using extra cement all as specified and directed by engineer-in-charge.

S&F 20mm PTMT , high pressure, with polytheene float and flynut complete, screwed for iron pipe orr brass ferrule and fixed in repairs

S&F tripal layer rotational moulded polythene water storage tank (Cylindrical vertical withclosed top) hoisted and fixed in position of 1000 ltrs capacity fixed with PVC tank nipples,complete all as specified in SSR Part I.

Dismantling water tanks and removing to store of 1000 ltr capacity

S & F galvanised mild steel wire cloth, 0.51 mm to 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, or galvanised wire staples,fixed in repairs all as specified .

M & L for Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones all as specified and directed.

S&F 4.8mm thick sheet glass ordinary quality and glazing with oil putty in square n. exc. 0.5sq.m in each pane complete all as specified.

S&F Anodised aluminium frame for doors, windows , ventilator with one or more rebates incl necessary joining cleats for fixing etc complete all as specified.

S&F anodised aluminium door shutter , aluminium section wt 0.55 kg / mtr including necessary joining cleats ,glazing clips, rubber eoprene packing , handles 2 Nos. in each door , hinges , anodised aluminium snap beading screws etc.

S&F anodised aluminium window / ventiletor shutter , side hung type without sash bar ,aluminium section wt 0.55 kg / mtr including necessary joining cleats , glazing clips, rubber packing , anodised aluminium snap beading screws , anodised aluminium fitting such as peg stays 150 mm long (1 No.) hingestype B-21 100mm long (2 Nos. )suitable handle (1 No) complete allas specified .

S & F in repair powder coated aluminum sliding window three track with frame & two glass shutter using 4 mm thick glass tinted modi guard and one shutter with stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperture 1.61 mm using aluminum powder coated section aluminum cleat , PVC track, bearing, handle lock rubber beading etc complete fittings as approved. Note :- Size of aluminum section shall be under – (i) three track top and vertical – jindal main 2010. Section No 20621 or equivalent as approved by GE. (ii) Three track bottom – Jindal main – 2010 section 20620 or equivalent as approved by GE. (iii) Shutter Vertical Section - Jindal main – 2010 section 20604 or equivalent as approved by GE. (iv) Shutter top and bottom - Jindal main – 2010 section 20604 or equivalent as approved by GE. (v) Shutter vertical middle ( interlock) - Jindal main – 2010 section 20605 or equivalent as approved by GE.

S&F powder coated aluminum ventilators shutter side hung type without sash, aluminum section weighing glazed clips, rubber packing anodized aluminum fittings such as peg stays 150 mm long (1 nos) hinges type B-21 100 mm long (2 Nos) suitable handle (1 Nos) complete all as specified.

S&F in repair bib taps 15mm bore dia, fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe all as specified .

S&F in repair Stop cock 15mm bore dia, fancy type, cromium pl;ated with long sunk and cup ( concealed type), cast copper alloy screwed down ,high pressure,with crutch or butterfly handle, screwed down, screwed both ends to iron pipe.Make Luster/BIR/Leader( Duly engrave ISI mared and conforming to relevant IS)

S&F angle valves chrome plated fancy type 15 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions

S&F in repair brass chromium plated towel rail of size 60cm fixed with chromium plated brass screws and plastic cleats complete all as specified & directed by Engineer-in-Charge. Make Jaquar Cat Part No. ACN-1111NM

S & F in repairs for brass chromium plated shower rose 125 mm size with swivel joint including fixing to 15 mm dia steel pipe or union.

Supply & fixing PVC connection in repair both sides brass unions internal for size of 15mm size with PTMT nuts of length 450mm long complete all as specified & directed by Engineer-in-charge.

S & F PVC waste pipe 32mm dia & 90 cm long complete all as specified and directed by Engineer-in-Charge.

M & L Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the internal /external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

M & L Preparation of newly plastered surfaces by applying two coats of interior grade wall putty and making it smooth with sand paper by mechanical method i.e. with hand electric grinder then applying two coats of oil bound distemper over one coat of cement primer including all as specified by mechanical method i.e. spray gun all as specified and directed by Engineer-in-charge.

M & L Preparation of Old plastered surfaces by removing old treatment and applying two coats of interior grade wall putty and making it smooth with sand paper by mechanical method i.e. with hand electric grinder then applying two coats of oil bound distemper over one coat of cement primer including all as specified by mechanical method i.e. spray gun all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered or unplastered surface of ceiling and applying three coats of white wash complete all as specified & directed by Engineer-in-Charge.

M&L for preparation of old decorated, plastered or pointed surfaces of ceiling and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

M & L three coat of white wash on old decorated plastered or unplastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

Dismantling of CI pipes or reinforced concrete pipes 100 mm dia fixed to wall etc complete all as specified and directed.

Dismantling of CI pipes or reinforced concrete pipes 75 mm dia fixed to wall etc complete all as specified and directed.

S&F, 75mm PVC (SWR) pipe singal shocket , waste and vent pipes, in any length with rubber ring joints,laid in fixed to walls

S&F, 110 mm PVC (SWR) pipe singal shocket , waste and vent pipes, in any length with rubber ring joints,laid in fixed to walls

S & F 110mm PVC ( SWR) sanitary connection socket to fit WC out-let all as specified and directed by Eng-In-charge.

S&F, 110mm PVC (SWR) Bends (any radius),

S&F, 75mm PVC (SWR) Bends (any radius), .

S&F PVC (SWR) 75 mm dia floor trap, plain with grating including jointing with solvent cement to connect waste pipe and fixed with PCC 1:2:4

Taking down steel tubing 15mm bore and connections,including cleaning for refixing or remove to store complete all as specified.

Taking down steel tubing 20mm bore and connections,including cleaning for refixing or remove to store complete all as specified.

S& F chlorinate PVC (CPVC) pipe 20 mm outer dia , having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings,i/c fixing the pipe with clamps at 1.00 spacing. This including jointing of pipes & fittings with one step CPVC solvent cement a and the cost of cutting chases and making good the same including testing of joints complete all as specified and directed . Make : supreme / vectus of equilent.

S & F 20mm bore medium grade tube galvanised with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor all as specified .

S&F gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia all as directed.

S&F in repairs drapry curtain rod 25mm dia, fancy type, fabricated out of mild steel sheet not less than 20 guage, including brackets and pair of decorated end knobs (finials), stop roller etc, pretreated powder coated natural color complete all as specified and directed by Engineer-in-Charge.

M & L for 50mm thick cement concrete type C2 1:3:6 (40mm graded aggregate) as in plinth protection .

Demolation of brick work built in cement motor

M&L Brick work with old size burnt fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed by Engineer - in - Charge .

M & L mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia all as specified and directed by Engineer - in - Charge .

M & L form work to soffits of suspended slabs such as roof slab and similar work not exceeding 200mm thick for rough finished surfaces of concrete all as specified and directed by Engineer - in - Charge .

M & L form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide for rough finished surfaces of concrete all as specified and directed by Engineer - in - Charge.

Demolition of Reinforced cement concrete (reinforcement cut as required to facilitate demolition) in floors / pavings, (below or above ground level) and of any description and in any position not otherwise specifically provided for all as specified and directed by Engineer - in - Charge .

M& L RCC 1;11/2:3 ( Nominal Mix type A-1 using 20 mm gradded aggreegaed as in Chajja facia selves parapet and railling ect completed all as specified and directed by Engineerr in Chagre.

Taking down eves and gutter and rainwater pipe

S & F PVC pipes (SWR) single socketed with rubber ring joints 110mm dia fixed to wall complete all as specified and directed by Engineer - in - Charge .

Supply and fix in repair PVC low level flushing cistern 10 litre capacity, valveless syphonic action type with float, handle including flush pipe of polythene of low or high density of PVC 32mm dia, 60cm long and bracket etc and making connection including making good disturbed portion complete all as specified and directed by Engineer-in-Charge.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) but including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, sheet cover complete.

S&F in repairs stainless steel kitchen sink with drainage board of overall size 915x460mm and bowl size 410x330x160mm with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe complete all as directed.

S&F sink mixer with swinging spout (wall mounted model) chromium plated brass with connection and nut complete all as specified and directed by Engineer-in-Charge. Make-ESSESS Cat Part No DE- 12 or equivalent.

S&F in repairs, 15mm bore brass chromium plated wall mixer with non-telephonic shower arrangement for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S & F in repair brass chromium plated central hole basin mixer with regular spout , popup waste system and 450mm long braided hoses with connection and nuts complete all as specified and directed by Engineer-in-Charge. Make Jaguar cat part No. QQT-7169B or equivalent

S&F Vitreous china wash basin white flat back size 550 x 400mm size,with pedestal incl cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe and 15mm pillar tap cast copper alloy with capstan head chromium plated complete fixed in repair.

Material and labour for cleaning of top roof surface by wire brushing, removing all dust, loose particle of concrete and washing with water and apply cement concrete flooring type B0 1:2:4 using 12.5 mm graded aggregate on roof slab all as specified and directed by Engineer-in-Charge.

M & L rendering 15mm thick water proofing plaster in CM 1:3 on slab / roof admixed including and with Dr. Fixit pidilite LW+@ 200 ml per bag of cement.

Preparation of roof top surfaces, providing and applying UV stable single component smart care damp proof ultra is a fibre reinforced elastomeric liquid applied water proofing membrane formulated with PU hybrid polymers and reinforcing acrylics fibres and having SRI of 106 on top of concrete roof surface in three coats including self primer at ratio pf damp proof and water 3:1 and coverage @ 1 Ltr /10 sqm with a thickness of 650micron Note: 6 Hrs interval between two coats will be maintain& the work will be carried out through company applcator duly got approved from Accepting officer in writing before incorporation and paid only after receiving of the warrenty certificate from the company. Make : Asian paint or equivalent as approved by GE

M & L 75mm thick PCC 1:4:8 , type D- 2, using 40mm graded aggregate as in sub base all as specified and as directed.

S&F machine pressed precast concrete interlocking paver block with grey cement , no pigment and pigment, any shape and size confirming to IS 15658-2006 of 60mm thick M-35 grade including.

M & L Sand filling under floors or in foundations including watering and consolidation.

M & L PCC 1:2:4, type B-1 , using 20mm graded stone aggregate as in kerbs or mud stops, rounded or chamfered on edges and similar work all as specified and as directed.

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; Cooler Stand, railings; framework of water tanks & similar work conforming to Fe 410-0 or Fe 310-0

S&F 1.00 mm thick mild steel, plain, black sheet in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and directed by Engr-in-charge.

Supply only Butt hinges 125mm size, medium weight, cold rolled mild steel.

S&F in repair steel window 1.25mm thick box type (primer coated) ERW hollow "P" section of size 60mm x 25mm single rebated comprises Glazed skeleton shutter ERW Section 50mm x 20mm and 1mm thick with two open able leaf consisting two Nos. of sash bars of flat iron 12mm x 3mm complete welded to frame with one vertical mullion of ERW box type "T" section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1, four Nos. for each window including following fittings welded to the frame shutter complete all as specified and directed by Engineer-in-Charge :- (a) Hold fast 150mm long of 12mm x 3mm made to shape - 04 Nos. per window. (b) Handle of "Z" section 20mm x 25mm, 100mm long - 01 No. per leaf. (c) MS tower bolt 150mm long - 02 Nos. per leaf. (d) MS pintol hinges of size 100mm x 14mm - 02 Nos per leaf. (e) "Z" section 20mm x 25mm x 100mm long stopper - Per leaf. Make : M/s Tee Pee Enterprises, M/s Friends Manufacturing Co., Kotkapura Note : Glass and painting shall be measured and paid separately under appropriate items of BOQ.

S&F steel ventilators fixed type 1.25mm thick Box Type (Primer Coat) ERW hollow "P" section of size 60mm x 25mm single rebated optional full glass or wire mesh complete all as specified and directed by Engineer-in-Charge.

M&L Cement concrete 1:3:6 type C-1 for filling of pressed steel frame, hold fast blocks etc all as specified .

Dismantling wrought iron or mild steel work of any description not otherwise provided for

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

Dismantling framed work of timber scantlings 40 sq. cm and over in any position

Erection and fixing of steel work in tubular trusses, purlins etc. including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240

S&F steel work in tubular trusses, purlins etc. including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F 0.71mm thick plain, aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed)

S&F hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

M&L for rendering 12 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces of wall, finished even & smooth (without using extra cement).

M & L for complete removal of existing treatment and applying two coats of white wash on old decorated plastered or unplastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

M & L for preparing plastered or unplastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed by Engineer - in - Charge .

M&L applying two coats of synthetic enamel paint over a coat of red oxide or zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

M&L applying two coats of synthetic enamel paint over a coat of red oxide or zinc chromate primer including preparation of new steel or iron surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint

M&L applying two coats of synthetic enamel paint including preparation of old steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

S&F Glass dividing strips, 3mm thick and 38mm wide complete all as specified and as directed.

M&L 40mm thick PCC type B-1, (1:2:4) using 20mm graded stone aggregate

S&F 4.00mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified.

M&L for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors

Taking down carefully existing aluminium/Copper point wiring light, fan socket or power bell complete with fitting such as sockets, ceiling roses, pendants batten holders regulators socket, call bells & making good to the disturbed surfaces of walls, matching the colour with existing Surface all as spd and directed by Engr-in-Charge. Note: Rate for making good shall be deemed to be included in above item rate.

M & L for point wiring complete with 1.5 Sqmm (Nominal area) PVC insulated multustranded fire retardant (low smoke unsheathed and multicore copper conductor cable with colour code and including PVC concealed conduict ISI marked and conduit fittings for one light point/fan point/exhaust fan/Bell Point controlled by one switch including PVC insulated 1.5 Sqmm single core copper earth wire to common earth and connecting to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified (Cost of MS sunken box and bakelite sheet included in the rate).

M & L point wiring with PVC FRLS insulated unsheathed multistranded copper conductor of size 1.5 Sqmm, 1100V grade in Existing concealed conduit, and one run PVC FRLS insulated unsheathed copper conductor of size 1.5 Sqmm as earth continuity wire and connected to common earth dolly using color code as per IS and all as specified with copper lugs/timbles inserted in existing MS boards/boxes complete heavy duty for housing switches, , regulators, bell push etc, and making good all disturbed work to match the existing for One light / fan point controlled by one way piano switch 5 Amp. and complete all as specified and directed.

All as per Srl item No. 128 here-in-before but one three pin socket outlet 5 Amps on the independent board complete all as specified.

All as per Srl item No. 128 here-in-before but one three pin socket outlet 5 Amps on the same board complete all as specified.

M&L for point wiring complete with 2.5 Sqmm (Nominal area) PVC insulated multistranded fire retardant low smoke unsheated and stranded copper conductor cable in and including PVC concealed conduit medium quality and conduit fitting for 3 pin 15 amp multicore switch socket combination including PVC insulated 2.5 Sqmm single core copper earth wire to common earth and connected to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified.

S&F switch Piano type single pole one way 5 Amp,230 VAC supply.

S&F socket two in one ,3 Pin 5 Amps 230 VAC supply, .

S&F switch Piano type single pole one way 15 Amp on laminated sheet top cover complete to all as spd (Sheet top cover incl in point wiring) .

S&F socket Pinao type 6 Pin 16 amp,230 VAC .

Supply & fixing PVC Lamp holder suitable for and including batten fittings ,LED Electric lamp 9 Watt with backalite 20mm back plate complete all as specified & directed, .

M&L for Ceiling Rose, surface bakelite 12 to 3 terminal, 240 volts, 5 Amp ISI marked complete all as specified and directed.

S&F Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting SPN 12 way 240 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed..

S & F of MCB suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA and 6 to 32 Amps all as specified and directed.

S & F of MCB suitable for 240 volts AC supply, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA and 16 to 40 Amps all as specified and directed.

S &F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP of capacity 16 A

M&L sub main wiring of PVC FRLS insulated unsheathed two core 6 sqmm copper multi stranded conductor including one run of single core copper conductor of size 6.0 sqmm as earth wire drawing in concealed PVC conduit complete all as specified and directed.(Note : Three length of submain considered as one unit)

M&L for WEE Plus LED bulk head luminaire of capacity 10 Watt an ideal energy efficient solution for upgrading conventional GLS bulkhead luminaires to LED bulk head IP 65 complete all as specified and directed by Engr-InCharge Make: Bajaj BIBWP LED 10W WH or equivalent in Havlls/Crompton Greaves/ Philips/Wipro/Syska as approved by GE.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S&F and testing LED light fitting 1x18watt 4 feet long including LED tube with driver complete suitable for fixation on wall/roof with body robust, corrosion resistant, superior finish and without any cracks or through h oles. The system wattage of fitting should not be more than 18 watt= 10%, surge protection of minimum 2 KV power factor should be more than 0.90 cool while colour, total hormonic distoration (THD) should not be more than 15% lumen output should not be less than 1700 lumens, total input voltage range 140-280V AC, colour rendering index should not be less than 80, Corelated colour should be minimum 6000 degree Kelvin.

Supply and fixing LED luminaire 600 mm x 600 mm,36 watt, 220 V AC surface type with high efficiency PMMA diffuser soft glare free light complete with driver suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engr-in-Charge.Make :Bajaj/ Havells/Phillips/Wipro as recommended by Engr-Incharge and approved by GE.

Supply and fixing post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete.

Supply and fixing Wall mounting fans complete with 3 blades and accessories, 230 V, 400 mm sweep. Five star rated with brushless direct current motor (BLDC) as specified and recommended by manufacturer all as specified and directed by Engineer in Charge Make : Bajaj/Orient/Crompton

S&F of Ceiling fan BLDC type , 1200mm sweep mounted in suitable arrangement for operation on 230 volts, single phase, 50 cycle per second, AC supply with electonic type regulator and connecting accessories BEE 5 Star rating and connecting up including three core PVC insulated PVC sheated copper conductor flexible cable from ceiling rose to fan fixing in ceiling complete and making the surface good after fixing the fan complete all as specified and directed. MAKE : BAJAJ/HAVELLS/CROMPTON

Suppy and fixing Exhaust fan metalic body heavy duty of size 300 mm sweep with louver shutter 220V, single phase AC including 1.0sqmm copper flexible cable twiested three core alongwith flelxible PVC condiut from ceiling rose to fitting testing complete all as specified and directed including cutting holes thruogh cement mortor wall for fixing 300mm sweep exhaust fan grouting the bolts, plastering and making good surface internally and externally wth existing colour.Make:Cromption/Havells/Bajaj

RUCHIKA CONSTRUCTIONS