PROVN OF CERTAIN SANCTIONED WORKS UNDER AGE (I) BHALRA

Amount

Excavating in post holes (or similar holes) each n exc 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in any type of soil.

Material and labour for PCC 1:3:6 Type C2 (using 40mm graded aggregate) as in foundation, filling and mass concrete as directed and specified by Engineer-in-Charge.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Rolled mild steel work as in roof trusses (beam, tee, angle iron etc) complete all as specified.

Supply and fixing rolled mild steel plates as in gusset plates, base plates etc complete all as spd.

Material and labour for painting, preparing new surface steel, priming with Red oxide, two coat of Synthetic enamel paint complete.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in any type of soil.

Material and labour for broken stone Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

Material and labour for 75 mm thick for PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base, foundations filling etc all as specified and directed.

Material and labour for chequered cement concrete tiles 300mm x 300mm x 25mm thick, set, jointed and pointed in neat cement slurry with grey cement and pigment as in floors .

Screed bed or bedding layer of mortar 20 mm thick in CM 1:4 for laying floor finishes all as specified and as directed.

Material and labour for PCC 1:2:4 type B1 (Using 20 mm graded aggr) as in coping and similar works incl necessary from work all as specified.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in any type of soil.

Material and labour for PCC 1:4:8 type D-2 (40mm graded aggregate) in foundation filling and mass concrete.

Material and labour for brick work with sub class B bricks, straight or curved on plan exc 6m mean radius built in CM 1:6

Rendering 15 mm thick cement plaster on fair surfaces of brick work or concrete surfaces in CM 1:4 finished to even and smooth sitfaces in without using extra cement incl.

Rendering 15 mm thick cement plaster on fair surfaces of brick work or concrete surfaces in CM 1:6 finished to even and smooth sitfaces in without using extra cement incl.

Material and labour for preparing new surfaces (plastered or unplastered) of walls and applying two coats of cement base paint over a coat of chalk whitening primer on surfaces of walls complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparing newly plastered or unplastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

Supply and fixing joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated (Fe 410 -W (GdeE- 250) quality A)

25 mm thick plain cement concrete 1:2:4 type B-0 ( using 12.50 mm graded stone aggregate) as in sub bases of floors finished even and fair.

Material and labour for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed for laying floor finish in CM 1:4.

Supply and fixing glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match and including 10mm thick plaster in CM (1:3) and pointed in white or colour cement to match all as specified and directed by Engineer-in-Charge.

Material and labour for 75mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection laid in alternate bays finished even and smooth without using extra cement incl form work complete all as specified and directed by Engineer-in-Charge.

Returning filling in excavated material in to trenches around pipe after laying of pipes and testing complete incl watering and well ramming in layers n exc 25 cm thick complete all directed.

Removing surplus excavated soil to a distance n exc 50 m and deposting where directed at a level n exc 1.5 m above the starting point complete all as directed.

Supply and fixing 500 ltrs capacity rotational moulded polythelene water storage tanks (cylindrical or vertical with closed top)hoisted and fixed in position all as specified in SSR Part-I and as directed by the Engineer-in-Charge.

Supply and fixing 20mm bore ball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball screwed for iron pipe & fixed (Minimum weight 15mm-142gms / 20mm-210gms / 25mm-455gms / 40mm-690gms) complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 15 mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed

Supply and fixing 20 mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed

Supply and fixing medium grade 15mm bore galvanized tubing with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

Supply and fixing medium grade 20mm bore galvanized tubing with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

Supply and fixing CP angle or plain stop valves, cast copper alloy, fancy type, chromium plated with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore complete all as specified and directed.

Supply and fixing 15mm dia PVC Connection 450 mm long with brass nuts complete all as specified and as directed.

S&F Vitreous china Urinal, Half stall type white with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, flush including 32mm bore PVC waste pipe, complete all as specified.

Supply and fixing self closing angle cock pressmatic for urinal with wall flange and 200mm connecting pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, flush pipe including 32mm bore PVC waste pipe, complete all as specified and as directed.

S&F vitreous china urinal partition white of size 310 x 700mm fixed to wall, plugs with chromium plated screws etc complete all as specified and directed.

Supply and fixing 15mm bore Pillar taps cast copper alloy fancy type with capstan heads chromium plated screwed down high pressure with or with out lettred Hot or Cold with long screwed shanks and flynuts ,screwed for pipes and fixing all as specified and directed by Engineer-in-Charge.

Supply and fixing 32mm bore PVC flexible waste pipe for WHB complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 75mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches.

Material and labour diameter of outlet in 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement

Supply and fixing PVC SWR pipe 75mm bends

Supply and fixing brass tubular towel rail 20mm dia 'D' type 60cm long between flanges

Supply and fixing soap dish vetreous china white approximate size 160 x 160 x 90mm as specified.

Supply and fixing vitreous china wash hand basin white flat back of size 550 x 400mm including bracket cutting for and pinning the ends of brackets or erecting stands exclusive of waste pipe but including brass chromium plated waste coupling with long screwed sank and fly nuts complete all as specified.

Taking down chowkat or frames with shutters (without taking off shutters from the frame), exc 1.5 sqm each complete all as specified.

Taking down chowkats or frames with shutters (with out taking off shutters from the frames) not exc 1.5 Sqm each , incl removing complete all as specified.

Supply and fixing 200 mm long Aluminium, anodised, barrel tower bolts of extruded section

Supply and fixing 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified.

Supply and fixing 100 mm long medium weight, cold rolled mild steel butt hinges.

Supply and fixing 150 mm long Aluminium handles, cast type, anodised.

Material and labour for pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate etc. complete, of frame size 125 x 60 mm, complete all as specified

Supply and fixing flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides 30mm thick

Supply and fixing 2nd class hardwood Glazed and skeleton shutters of 30mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats.

Material and labour for providing cement concrete 1:3:6 type C-0 using 12.5mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast complete all as specified.

Supply and fixing anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleates for fixing etc. complete all as specified.

Supply and fixing anodised aluminium sliding window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified.

Supply and fixing anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, pivots, wheel set rulers, G Channel, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified.

Supply and fixing 4.8 mm thick ordianary quality sheet glass exe 0.5 sqm in each pane of glazing with oil putty /beading etc all as specified and directed by Engineer-in-Charge.

Material and labour for 9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as specified and directed.

Supply and fixing aluminium die cast body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed all as specified and directed.

Supply and fixing 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified.

Supply and fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples for aluminum window shutters all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation , etc.) or insulation boards/ slabs/ blankets any thikness including cover fillets.

Dismantling of timber scantling unframed 40 sqcm and over in section , in any postion all as specified.

Dismantling wrought iron or mild steel work of any description not ortherwise provided for

Dismantling framed trusses nexc 10m span complete all as specifieid and directed by Engineer-in-Charge.

Dismantling CGI corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof coverings, complete all as specified and as directed by Engineer-in-charge.

Material and labour for 4mm thick non asbestos fiber cement building boards as in false ceiling fixed to aluminium snap grid frame work size 605 x 605mm with using 36.5mm x 23.5mm x 1.5mm thick main tee, 23.5 x 23.5 x 1.28mm cross tee and 25 x 25 x 1.5mm angles fixed to perimeter of wall including necessary supporting hanger with 3 mm dia GI wire and J bolts washer nuts for securing frame work to ceiling suspended @120 cm c/c both ways, complete all as specified and directed.

Supply and fixing PVC wall panelling made up of PVC hollow panels 25/30cm in width and 10mm thickness interlocking pattern of approved shade and design fixed to wall or ceiling all as specified and directed.

Material and labour for second class hard wood in scantling clean sawn timber framed and fixed complete all as specified and directed.

Material and labour for 18/19mm thick pre-laminated partical board interior grade prelaiminated one side with decorative lamination and other side white lamination fixed with screw or nails complete all as specified.

Supply and fixing continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30mm for cupboards complete all as specified and directed.

Supply and fixing ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

Supply and fixing 75mm long stainless steel drawer modular handles, projection ring drop (40mm to 50mm), ring on 4 screw plate complete all as specifeid and directed.

Fixing only steel tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.11611979 grade St.-240 complete all as specifieid and directed by Engineer-in-Charge.

Demolition of cement concrete any description (unreinforced) in ground floors and pavings not exceeding 15 cm in thickness all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

Material and labour for walling of random rubble stone masonry uncoursed well bounded bedded and solidly hearted built in CM 1:6 brought upto coursed.

Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4

Material and labour for preparing newly plastered surfaces of wall and applying two coats of OBD over a coat of alkali resistant primer with putty to prepare the surface even and smooth complete all as specified and directed.

Material and labour for preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified.

Material and labour for preparation of old painted steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of synthetic enamel paint all as specified and directed.

Material and labour for coloured vitrified tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed in CM (1:4) jointed in neat cement slurry and pointed in coloured cement complete all as specified and directed by Engineer-in-Charge.

Material and labour for non skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed for laying floor finish in CM 1:4 complete all as specified and directed.

Material and labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab 15 mm screed bed in 1:4, including rubbing and polishing over shelves complete

Material and labour for RCC M-25 design mix (20mm graded stone aggregate) in foundation including rafts, footing, foundation beams, plinth beams and mass concrete all as specified and directed.

Material and labour for providing RCC M-25 design mix (20mm graded stone aggregate), beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

All as per description of Srl Item No. 90 here-in-before but in chajjas

Material and labour for providing RCC M-25 design mix (20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span all as specified and directed.

Material and labour for providing RCC M-25 design mix (20mm graded stone aggregate) as in columns, pillars, piers, post and struts all as specified.

Material and labour for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality confirming to Fe-410-S or Fe-410-O complete all as specified.

Material and labour for mild steel TMT bare 5mm and over upto and including 10mm dia bars as in stirrups cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding mild or securing with clips confirm (Fe-410W or Fe-290) as specified.

Use and waste of form work to side and soffit of plinth beam for rough finished surface on flat surface complete all as specified.

Use and waste of form work to side of pillars, columns and stanchions, square or rectangular, for rough finished surface of concrete complete all as specified.

Use and waste of form work to sides and soffits of floor or roof beams, beam hunching, girders, bressummers, lintels, cantilevers, shelves, including sup-ports, overhangs, etc. also splays between floors and beams etc.

Material and labour for PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) (mechanical crushed) as in surface channel and drains complete all as specified.

Material and labour for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms moulds, mitred/stopped ends etc complete all as specified.

Material and labour for PCC 1:2:4, type B-1 using 20mm graded stone aggregate as in walls complete all as specified and directed.

Use and waste of formwormk to face faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached llasters, buttresses, etc, for rough finished surfaces of concrete complete all as specified.

Material and labour for 100mm thick Cement concrete type B-2, 1:2:4 (40mm graded aggregate) as in hardstanding complete all as specified and directed.

Forming construction joints 66mm deep x 10mm wide, filled with sealing compound grade 'A' thickness of slab 100mm complete all as specified and directed.

Material and labour for 100mm thick PCC type D2 1:4:8 (using 40 mm graded granite stone aggregate) in sub base of flooring all as specified and directed.

Material and labour for factory made (rectified) precast concrete designer chequered tiles any colour, shape and size not less then 300mm x 300mm x 20mm thickness (compressive strength not less than 250 Kg/Sqm), pointed with grey cement and pigment over and including 20mm thick CM 1:6 screed bed or bedding layer complete all as specified and directed.

Supply and fixing PVC (SWR) pipe 110 mm bore single socketed in any length with rubble ring joints as in weep holes complete all as specified and directed by Engineer-in-Charge.

Supply and fixing steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

Supply and fixing factory made Solid PVC Door Frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing facotry made soild panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail lock rail& bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rail with suitable PVC sheet beading, & joined together with solvent cement, supplying & fixing in the frame at site as perr specification & drawing complete all as specified and directedby the Engineer-in-Charge.

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified.

Supply and fixing glavanized mild steel wire cloth 0.56mm normal dia of wire and averagewidth of apparatus 1.18mm and fixed width tinned lacks of galvanized wire staple.

Supply and fixing Butt hinges of size 100mm length, extruded aluminium ally with galvanished mild steel hinges pin, anodized & fixed, type C-21

Supply and fixing Alluminium, anodized, barrel tower bolts 150mm extruded section.

Supply and fixing 150mm long extruded aluminium alloy anodised handles fabricated type complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed with 200mm long complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 15mm bore bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterily handle, screwed for iron pipe or for brass ferrule and fixed.

Supply and fixing wall mixer (Cera cat part No F3001404) with flanges, for mixing Hot & Cold water screwed down for iron pipe of 15mm bore complete all as specified and directed.

Supply and fixing ocean central hole wash basin mixer (Make - CERA Cat Part No F-3001461) complete all as specified and directed.

Supply and fixing for PVC connections of 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

Supply and fixing Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified.

Supply and fixing glass shelf assembly consisting of 5.5mm thick sheets glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

Supply and fixing 1000 ltrs capacity rotational moulded each polythelene water storage tanks (cylindrical or vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I and as directed by the Engineer-in-Charge.

40 mm thick plain cement concrete 1:2:4 type B-1 (using 12.50 mm graded stone aggregate) as in sub bases of floors finished even and fair complete all as specified and directed.

Preparation of old painted steel surfaces of any description not other wise described over 10cm width or girth and applying two coat of synthetic enamel paint, designed and pattern as approved by Engineer-in-Charge complete all as specified.

Taking down carefully by unscrewing from boards/outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site or carrying to the store (To be measured only when found serviceable in all respects complete for reuse)and making good disribution surfaces of walls, floors, etc. complete all as specified and directed by Engineer-in-charge.

Material and labour for point wiring with multistranded copper conductor of size 1.5 sqmm PVC insulated unsheathed FRLS cable in and including PVC conduit and assessories of suitable size for concealed wiring including 1.50 sqmm copper earth wire (green colour) FRLS cable as earth continuity conductor connected to main earthing and common earth terminal for one ligh point or fan point or bell point controlled by one No, one way switch using cable of different insulation coloour for colour coding including 3 mm thick laminated sheet cover Modular fittings, mild steel or cast iron boxes including making good to distrubed surfaces of wall/ floor, complete all as specified and as directed.

All as per the description of Srl Item No. 127 here-in-before but for one 3 pin socket outlet 5 Amp independent, complete all as specified and as directed.

All as per the description of Srl Item No. 127 here-in-before but for one 3 pin socket outlet 5 Amp on same board, complete all as specified and as directed.

All as per the description of Srl Item No. 127 here-in-before but for one 3 pin socket outlet 15 Amp independent board with cable of size 4.0 Sqmm with 2.5 sqmm copper conductor in green colour for earth continuity conductor, complete all as specified and as directed.

Supply and fixing for Modular switch flush type 6 Amp single pole one way including taking down all as specified and directed by Engineer-in-Charge.

Supply and fixing Modular Socket outlet 2 in 1, 3 pin 6 Amp flush type complete including taking down, all as specified.

Material and labour for Modular socket , 5 pin, 6 and 16 Amp flush type universal including taking down and all as specified and directed by Engr-in-charge.

Material and labour for Modular switch piano , 16 Amp flush type universal including taking down and complete all as specified and directed by Engineer-in-Charge.

Supply and fix recess mounting octane plus LED 2 x 2 panel ultra modern recess mounting luminaire with high performance LEDs, suitable for mounting with Armstrong/grid ceiling of capacity of 36 W 6500K with suitable drivers. Plane front frame with translucent cover fixed to the housing all as directed by Engineer-in-Charge.

Supply and fixing LED lights fitting 1x 30W, 220V, AC Decorative ultra slim polycarbonate LED lighting fixture with high lumen output, environmental friendly, energy efficient ready to use pack, holder including LED Tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete ll as directed by Engineer-in-Charge.

Supply and fixing LED light fitting 1x9W/1X10W Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable sizeS & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed.

Material and labour for ceiling rose surface bakelit 65x50mm three terminals complete including taking down where require and making necessary connections all as specified and directed by Engineer-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and directed by Engineer-in-charge

Supply and fix stepped type Modular fan regulator 1 module for ceiling fan 1400/1200 mm sweep.

Taking down old and unserviceable, distribution board any type including fuses, MCBs etc after removing all connection and make good the disturbed surface all as directed by Engr-in-chanrge.

Supply and fixing MCB DB 8- way, single door, 240 volts for Sheet Steel, Phosphatised, Powder Painted MCB DBs with Bus Bar,Neutral Link, Earth Bar and Din Rail (In accordance with IS 13032, IS 8623, IEC/BSEN 60439-3) all specified and directed by Engineer-in-Charge.

Supply and fixing MCB SP 5-32 Amps 'C' series 240V 50Hz 10 KA suitable for lighting and other domestic loads complete including taking down where require all as specified and directed by Engineer-in-Charge.

Supply and fixing Exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers all as specified and directed.

Supply and fixing MCB SPN 40 Amps 'C' series 240V 50Hz 10 KA suitable for lighting and other domestic loads complete taking down all as specified and directed by Engineer-in-Charge.

Supply and fixing Earthing complete with galvanised steel earth plate electrode, 60x60cmx 6.0 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level,connected to galvanised earth lead wire 4.0mm dia by means of bolts,nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing on completion sheet complete including taking down and all as specified and directed by Engineer-in-Charge.

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated aluminium Solid conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core 16 Sqmm cable flat or circular complete all as specified and directed.

Supply and fixing switch piano flush type 5/6 Amp single pole one way complete all as specified and directed.

Supply and fixing socket outlet 2 in 1, 3 pin 5/6 Amp flush type complete all as specified and directed.

Supply and fixing socket 5 pin, 5 and 15 Amp flush type universal complete all as specified and directed.

Supply and fixing for switch piano, 5 pin, 15 Amp flush type universal complete all as specified and directed.

Supply and fixing LED tube lights fittings 1 x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing MCB DB 2 way, single door, 240V for sheet steel, phosphatised, powder painted MCB DBs with Bus Bar, Neutral link, Earth Bar and Din Rain (in accordance with IS-13032, IS-8623, IEC/BSEN 60439-3) complete all as specified and directed.

Supply and fixing 32A SPN amp rating 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning including taking down complete all as specified and directed.

Material and labour for point wiring with and incl 1.5 sqmm (nominal area) PVC insulated multistranded copper conductor FRLS in and incl PVC casing and capping ISI marked 20/30 mm size or as required at site incl with its fittings and fixture such as ties, bends, elbows and juction boxes etc with 1.5 Sqmm copper conductor cable green in colour as earth continuity conductor connected to main earthing and common earth terminal ,One light point/fan point controlled by one way switch all as specified and directed

All as per the description of Serial Item No. 155 here-in-before but for one 3 pin socket outlet 5 Amp same board, complete all as specified and as directed.

All as per the description of Serial Item No. 155 here-in-before but for one 3 pin socket outlet 5 Amp Independent Board, complete all as specified and as directed.

All as per the description of Serial Item No. 155 here-in-before but for one 3 pin socket outlet 15 Amp independent board with cable of size 4.0 Sqmm with 2.5 sqmm copper conductor in green colour for earth continuity conductor, complete all as specified and as directed.

Supply and fixing switch socket combination 2 in 1, 3 pin, 5A and 16 Amp flush type universal with fuse and neon indicator all as specified and directed by Engineer-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing electric water heater storage type, 230 Volts 50Hz AC supply of capacity 25 ltrs, ISI marked with 5 star rating having inner tank made of extra thick superior cold rolled steel, Puf insulation, outer tank of feroglas with single weld line design and external thermostat having range 25 to 75°C with 3 pin plug top and including CP connection of 15 mm dia for water inlet and outlet, all as required at site or as directed by Engr-in-Charge.

RAVI KUMAR

A S CONSTRUCTION

M/S SUSHEEL KUMAR Govt. CONTRACTOR

M S BANSI LAL CONSTRUCTION CO