PROVN OF 02 X TOILET AT TRG AREA REPTA OFFICE ROOM FOR Q WKS SEC AND BATHROOM WITH TOILET AT HQ 51 SUB AREA AND WAITING SHED FOR

Amount

Surface excavation n.exc 30cm deep averaging 15.00cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in soft / loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 M and making good surface complete all as specified and as directed.

Excavation in trenches not exc 1.50 m wide and not exc 1.50 m deep for foundation or for shafts, wells cesspits,man holes etc not exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft / loose soil complete all as specified and as directed.

Returning, filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each in soft / loose soil etc complete all as specified and as directed.

Removal of surplus excavated soil to a distance exc 250m but nexc 500m and depositing as directed at a level n exc 1.5m from the starting point complete all as specified and as directed.

Material and labour for hardcore of gauge n exc. 63mm with broken stone or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.complete all as specified and directed.

Material and labour for 25 mm thick PCC (1:2:4) type B0 (using 12.5 mm graded crushed stone aggregate) as in floor finished rough to receive tiles complete all as specified and as directed.

Material and labour for 75 mm thick plain cement concrete (1:4:8) type D2 using (40 mm graded crushed stone aggregate) as in sub base of tiles/floor of hard standing/path etc complete all as specified and directed.

Material and labour for 100 mm thick plain cement concrete (1:4:8) type D2 using (40 mm graded crushed stone aggregate) as in sub base of tiles/floor of hard standing/path etc complete all as specified and directed.

Material and labour for 75 mm thick, PCC 1:3:6, type C2 (using 40 mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide and 30 mm deep at every 2.4 mtrs interval filled with sealing compound grade 'A' etc complete all as specified and as direted.

Material and labour for PCC (1:3:6) type C2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed

Material and labour for PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed

Material and labour for PCC (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in coping / benching etc complete all as specified and as directed.

Material and labour for precast concrete 1:2:4 type B-1 (using 20mm graded stone aggregate)in manholes covers set in CM 1:4 including necessary form work (Note :-reinforcement will be measured and paid separately) including necessary form work etc complete all as specified and as directed.

Material and labour for RCC M-25 (20mm graded stone aggregate) design mix as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete etc complete all as specified and as directed.

All as per item no15 above but in beams, seimic bands, cantilevers, bressumers and lintels .

All as per item no 15 above but in chajjahs complete all as specified and as directed.

All as per item no 15 above but in columns complete all as specified and as directed.

All as per item No 15 above but on slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies deck slabs and in shelves and the likew complete all as specified and as directed.

Material and labour for brick work with old size sub class 'B' bricks straight or curved on plan exc. 6m mean radius and built in CM 1:6 etc complete all as specified and as directed.

Material and labour for brick work with sub class `B' bricks old sized straight or curved on plan exc 6 M mean radious and built in cement mortar 1:4 etc complete all as specified and as directed.

Material and labour for brickwork with subclass ‘B’ old sized bricks, straight or curved on plan to any radius in half brick thick walls and built in CM 1:4 etc complete all as specified and as directed.

Cutting chases in brick masonry walls built in cement mortor for concealed water tubing or concealed conduit wiring, etc., and making good in CM 1:3, cutting not exc 10 cm girth etc complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc rough finishwd surface of concrete complete all as specified and as directed.

Material and labour for formwork to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified and as directed.

Material and labour for formwork to chullah hoods, chajjas, troughs and similar works as in rough finished surfaces complete all as specified as directed.

Material and labour for form work on flat sides to soffits of suspended roof slabs not exceeding 200mm thick (Horizontal or sloping) rough finished surface of concrete all as specified and as directed.

Material and labour for mild steel TMT bars 10 mm dia and over cut to length, bent to shape as required including cutting, bending cranking, hooking end and binding with mild steel wire(annealed) not less than 0.9mm dia as in reinforcement bar complete all as specified and as directed

Material and labour for mild steel TMT bars 5 mm dia and over upto and including 10mm dia cut to length, bent to shape required including cutting, cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and as directed.

Material and labour for framed work such as grills, grating, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways railing framework of water tank and siliar work all as specified

Supply and fixing steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 graded St 240 with one shop coat of zinc chrome primer paint complete all as specified and as directed.

Supply and fix Fe-290 (Grd E-165) in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and as directed.

Supply and fix compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc.Fe 410 -W (Gde- E- 250) quality-A comlete all as specified and directed.

Material and labour for Pre- painted hot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws complete all as specified and as directed.

Material and labour for Pre- painted hot dip aluminium Zinc alloy metalic coated plain steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws as specified complete all as specified and as directed. Note: To be executed for provision of ridges and hips.

Material and labour for providing and fixing E-board Make: Everest, Design "Lake and Hill" or equivalent of size 605 x 605 x 4mm thick white prelaminated set embosed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section (White powder coated). The framework shall comprise of main runner made from 0.33mm thick GS sheet and of size 24 x 32x x300mm and soaced at 1200mm maximum centres securely fixed to structural soffits with hangers of 1.60mm dia GI wire to be fixed with approved rawl plugs, adjusters and screws. Flush fitting of 1200mmm long cross Tee (with double stiching) to be interlocked between main runners at 600mm centre to form 1200 x 1600 mm modules cross tee longer than 600mm to be supported independently. 600 x 600mm doubles to be formed by fittings 600mm long cross tee centrally between the 1200mm cross tee. Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19 x 19 mm and 300mm long of white colour all as per manufacturers instructions complete all as specified and as directed

Material and labour for suspended false ceiling using E-grid (exposed ceiling suspension system) of grid size 600x600mm with main runner 38mmx24mm and wall angle 24mmx24mm using 4mm thick Non Asbestos fiber cement designer board (E-Board classic) in a grid of GI system duly suspended with 4mm dia GI bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures air conditioning diffuser and ducts, sprinkler, smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220mm maximum c/c, the last hanger at the end of each main runner should not be placed at more than 450mm from the adjucent wall, flush fitting 1220mm cross tee to be interlocked between main runners @ 610mm c/c so as to from 600x600mm grid and painted with two coats of OBD over a coat of primer before installing it on the grid complete all as specified and as directed

Supply and fixing anodized aluminium push pull type fully glazed door shutter (single leaf / double leaf) having top rail of section 85.00mmx44.45mmx2.00mm, bottom rail of section 85.00mmx44.45mmx2.00mm thick, door verticals of section 44.45mmx44.45mmx2.00mm thick and lock rail of section 85.00mmx44.45mmx2.00mm thick with aluminium anodized chowkats of section 63.50mmx33.10mmx2.50mm thick including necessary jointing cleats, glazing clips, rubber packing, snap beading, screws, handle and locking arrangement etc. 5.5 mm thick float glass tinted quality on top/bottom panel complete all as specified and as directed. (Note : Door closer shall be measured and paid separately)

Supply and fixing anodized aluminium sliding glazed window shutter (double leaf glazed shutter and single leaf mosquito proof shutter each in single frame work) without sash bars with anodized aluminium shutter of section 40.00mmx20.00mmx1.10mm thick and window chowkat of section 92.00mmx29.50mmx1.20mm thick including necessary jointing cleats, glazing clips, rubber packing, snap beading, screws, handle, tower bolts and locking arrangement etc. and including 4mm thick sheet glass, tinted quality on panel and stainless steel wirecloth or aluminium anodized wire cloth for mosquito proofing, 0.45mm nominal dia and average width of aperture 1.40mm fixed with aluminium screws and tacks and making good to disturbed surfaces complete all as specified and as directed

Supply and fix providing and fixing powder coated Aluminium (minimum thickness of powder coating of 50micron) work for doors, windows, ventilator and partition (fixed portion) with extruded built up standard tubular sections/ appropriate Z sections and other section of approved make confirming to IS ; 733 & IS : 1285, fixing with dash fastners of required dia and size, including necessary filling of the Gaps at Junctions, ie. at Top, bottom and sides with required EPDM rubber/neoprene gasket etc. Al section shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Al snap beading for glazing/panneling, CP Brass/Stainless steel screws, complete all as specified and as directed

Material and labour for 12mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice laminations and other side blenching white lamination, fixed with screws to aluminium frame work complete all as specified and as directed

Supply and fix factory made solid PVC moulded door shutter with particle board , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed

Supply and fix factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tube for top and bottom rails, MS frames shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stills and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ scaled to the stiles and rails with suitable PVC Sheet beading and jointed together with solvent cement as per drawings and specifications as catered in SSR Part – II 2004

Material and labour for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing etc complete all as directed.

Material and labour for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws complete all as specified and directeds.

Supply and fix continuous (piano) hinges, 40 mm (when flaps open )mild steel, bright finish or electrogalvanised complete all as specified and as directed

Supply and fix 150 mm size aluminum anodised, barrel tower bolts of extruded section etc complete all as specified and as directed

Supply and fix aluminum alloy anodised, sliding door bolts with hasp and staple, (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed 300mm long etc complete all as specified and directed.

Supply and fix stainless steel butt hinges 100 mm long medium weight complete all as specified and as directed.

Supply and fix 150 mm long extruded anodized aluminum alloy handles, fabricated type, etc complete all as specified and as directed.

Supply and fix 100 mm long extruded anodized aluminum alloy handles, fabricated type, etc complete all as specified and as directed.

Supply and fix aluminium door closer (Diecast) body hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and complete all as specified and as directed.

Supply and fix powder coated aluminium alloy curtain rails 20mm dia with brackts fixed to required lenghts etc complete all as specified and as directed.

Supply and fix 25mm dia harrison rails, stainless steel, CP Curtain rod with fixing brackets, dooms, stops, rollers etc. complete all as specified and as directed

Supply and fix stainless steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fix steel ventilator with top hung shutter including hinges, steel peg stay, complete with glazing bars, dovetailed or welded etc complete all as specified and directed.

Supply and fix 4 mm thick figured glass, pin head type and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed.

Material and labour for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Material and labour for 20 mm thick Granite slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in 20 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. including rounded/half rounded edge and hole for gas pipe in pre-cast slab as well as stone slab in cooking platform complete all as specified and as directed.

Material and labour for granite 20mm thick (of any type) work (table rubbed and polilshed)for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing in wite cment (1:2) using marble dust with admixture of pigment to match with shade of granite over 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc complete all as specified and as directed.

Material and labour for glazed ceramic coloured tiles in vertical surface 300mmx 600mmx 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match etc including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

Material and labour for non - skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) laid in floors area of each tile exc. 0.18 sqm but n.exc 0.38 sqm, in floors etc. with and incl 15mm thick screed bed in CM 1:6 , set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed.

Material and labour for vitrified ceramic tiles, light shade, 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, laid in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles, over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

Material and labour for 10mm thick vitrified tiles light shade area of each tile n exc 0.36sqm as in vertical surfaces such as skirting/dados etc etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

Material and labour heavy duty parking tiles size 300mm X 300 mm X 10 to 12 mm thick /400 mm X 400 mm X 10 to 12 mm thick white cement and pigments of approved maked jointed with cement slurry and pointed with white cement mixed with pigment to match with the tiles over and including screed bed of 20 mm thick in cement mortar (1:6) complete all as specified and directed

Material and labour for coloured non skid cermic tiles 6 to 7mm thick (Square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Material and labour for rendering 5mm thick cement plastering in cement mortar 1:3 as on ceiling, chhajjas and other concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for 10 mm thick rendering in CM 1:6 on brick/ concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as directed.

Material and labour for rendering 15mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

Material and labour for rendering 15mm thick external in CM 1:4 on fair faces of brick/concrete surfaces finished even and smooth without using exta cement with using WPC @200ml /50 kg by the wt of cement. complete all as specified and as directed (WPC shall be measured and paid seperately.)

Supply only integral water proofing compound of approved make

Material and labour for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed.

Material and labour preparation newly plastered surface and applying three coat of white wash on ceiling all as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls and applying one coat of alkali resistant primer over a coat of birla white cement putty 1.5 mm thick ,sanding the surfaces till smooth finish is obtained and finally applying two coats of oil emulsion distemper etc complete all as directed.

Material and labour preparation newly plastered surface and applying two coat of exterior emulsion weather resistant/weather shield paint with primer on over & including a coat of thick putty 1.5 mm thick concrete/plaster surfaces including prepation of plastered or unplastered surfaces complete.

Material and labour for prepration of newly plastered surfaces of wall for application primer complete.

Material and labour for one coat of acrylic water based exterior grade primer @0.9 ltr (undiluted)/10 sq mtrs diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI Allow 6-8 hrs to dry the surface for painting of subsequent coats complete all as specified and directed.

Material and labour for two coat water based premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI.Allow 6-8 hrs to dry the surface in both the coats of paint complete all as directed.

Material and labour for water proofing treatment to sunken floor with polymeric water proofing membrane after cleaning the surface by wire brushes,brooming,removing dust and applying treatment as under :- (a) Material and labour Plastering 15mm thick in CM 1:4 using 100% coarse sand on roof including WPC 3% by weight of cement. (b) Applying a coat of bitumen primer conforming to IS-3384 - 1965 @ 0.50 lit/Sqm and allow to dry. (c) Applying one coat of hot blown bitumen grade 85/25 as per IS-702-1988 @ 1.20 Kg/Sqm of each coat applied over primer incl cleaning of surfaces . (d) Supply and laying polymeric water proofing membrane of 3mm thick with consists of a centre core 90 micron thickness molecular high density polyethylene film protected on both sides with a high quality polymeric asphaltic mix will be protected on both sides with20 micron HMHDPE film, weight not less than 3.50 Kg/Sqm over area including overlapping as per manufacturers instruction. (e) Applying two coat of Aluminium paint over the APP modified membrane @ 0.11 Kg/Sqm.

Material and labour for preparation of newely plastered surface or unplastered surfaces of walls and applying two coats of cement based paint over one coat of primer/ alkali resitant primer complete all as specified and directed..

Material and labour for preparation of new steel surfaces exc 10 cm width/girth and applying two coats of synthethic enamel paint over a coat of primer etc complete all as directed.

Supply and fix GI tubing 15 mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fix GI tubing 20 mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fix 1000 litres capacity rotational moulded polyethylene water storage tanks with 20mm bore ball brass valves, high pressure, with polyethylene float and fly nut (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I etc complete all as specified and as directed.

Supply and fixing rotational moulded polyethylene water storage tank 500 litre capacity of triple layered layer wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and as directed.

Supply and fix 20mm bore gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe etc complete all as specified and as directed.

Supply and fix PVC connections 15mm size with PTMT nuts of length 450mm etc complete all as specified and as directed.

Supply and fix fancy type brass chromium plated soap dish fixed with screws and wooden/plastic cleats etc complete all as specified and as directed.

Supply and fixing vitreous china counter top wash basin oval type of size 600x450mmx165mm with chromium palted waste coupling long shank but including brackets, PVC waste pipe 32 mm bore 600mm long complete all as specified and as directed.

Supply and fixing vitreous china wash hand basin colour flat back of size 550x400mm including brackets, chormium plated pillar tap, waste coupling, PVC waste pipe complete all as specified and as directed.

Supply and fix vitreous china one peice water closet of size 300x730x740mm mm and making necessary connection to drain or out going pipe fixed on floor complete all as specified & directed. (Make : Jaquar cat No SLS WHT 6851S300PP or as equivalent)

Supply and fix repair vitreous china wash down water closet (EWC) pan (pedestal pattern) white, including seat cover, closed pattern with flat bottom and cover with chromium plated hinging device complete all as specified and as directed.

Supply and fixing vitreous china urinal flat back (half style) with sensor size 480x300x740mm & including chromium plated waste coupling long shank, PVC flexible discharge / waste pipe socketed end including connection to flushing pipes and out going pipes and including fixing plugs complete all as specified and as directed. (Make : Jaquar cat No URS WHT 13255 or as equivalent)

Material and labour for Vitreous china urinal, half stall white (excluding flushing cisterrn) including urinal spreader, PVC connection, 40mm PVC waste pipe & 40mm waste coupling providing and fixing plugs, bedding urinal against wall in mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe, grating and union for discharge pipe complete all as specified and as directed.

Supply and fix Vitreous china urinal partition white of size 310 x 700 mm complete all as specified and as directed.

Supply and fixing PVC low level flushing cistern, pastel coloured, 10 ltrs capacity, valveless, syphonic action type including all fittings and flush pipe, PVC connection pipe complete all as specified and as directed.

Supply and fixing brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

Supply and fix 15mm fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed.

Supply and fix 15mm bore bib taps with wall flange chromium plated screwed down for galvanised iron pipes complete all as specified and as directed.

Supply and fix 15mm bore bib taps two way with wall flange chromium plated screwed down for galvanised iron pipes complete all as specified and as directed.

Supply and fixing 15mm bore angle stop cock with wall flange chromium plated screwed down for galvanised iron pipes complete all as specified and as directed.

Supply and fix stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 20mm bore of iron pipe or for union and fixed all complete all as specified and as directed.

Supply and fix butterfly stainless steel toilet jet spary with 1.5m PVC hose pipe and fixed to angle stop cock complete all as specified and as directed.

Supply and fixing chromium plated tubular towel rail between flanges fixed with steel screws complete all as specified and as directed. (Make : Hindware Cat No.F870012 or equivalent as approved by GE

Supply and fix tubular towel ring with brass chromium plated brackets fixed with screws and wooden/plastic cleats etc. complete all as specified and directed.

Supply and fixing sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 120mm wide with and 600 mm long chromium plated bracket guard nad railing fixed with steel screws on wall complete all as specified and directed.

Material and labour health faucet ABS with 1.2 m SS flexible tube & ABS wall hook fixed with necessary fixers complete all as specified and directed.

Supply and fix ordinary quality sheet Glass 5.50mm thick and glazing in rectangular/square exc 0.5 sq. m in each pane complete all as specified and directed. Sheet glass,

Supply and fix glass corner shelf with 3 piece set chromium plated railing complete all as specified and directed.

Supply and fix hand dryer automatic high speed motion sensor complete all as specified and directed..(Make : Jaquar cat No HDR SSF SK 2807 or as equivalent)

Material and labour for providing toilet paper holder including fixing to wall complete all as specified and as directed.

Supply and fix wall mounted liquid hand wash dispensor complete all as specified and directed. (Make : Jaquar cat No SDR WHT DJ0010FN or as equivalent)

Supply and fix grating doom 125mm dia with waste hole of PTMT (Min weight 40 gms). complete all as specified and directed.

Supply and fix 110mm bore of pipe PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls etc complete all as specified and directed.

Supply and fix PVC (SWR) pipe 110 mm bore single socketed in any length with adhesive joint fixed to laid in trenches or floor/wall including ms clamps complete all as specified and directed.

Supply and fix 110 mm bore of pipe PVC (SWR) plain bends any radius etc complete all as specified and directed.

Supply and fix in repairs, 75 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

Supply and fix PVC (SWR) pipe 75 mm bore single socketed in any length with rubber ring joints laid in trenches or in floor complete as specified complete all as specified.

Supply and fix 75 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

Supply and fix PVC (SWR) vent cowl for 110 mm bore pipe complete all as specified and directed.

Supply and fix 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement etc complete all as specified and directed.

Material and labour concrete bed in cement concrete 1:3:6 type C-2 to drain pipes 150 mm bore Pipe including packing under, and haunching against the sides of pipes after they are laid and tested in complete all as specified and directed.

Supply and fix SGSW pipes 150 mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors and jointed complete all as specified and directed.

Material and labour for point wiring with 1.5 sqmm, single core, PVC insulated and PVC unsheathed FRLS cable, 1100 volts grade IS-694 marked, with multistranded copper conductors and earth continuity wire with 1.5 Sqmm copper conductor cable (including connecting to earth dolly) laid/fixed with and including PVC rigid conduit on walls/ceiling ( concealed), with MS/PVC terminal boxes fixed flush with wall surface for mounting switches, sockets, regulators etc. including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly for one light or fan point controlled by one 5 Amp switch one way complete all as specified and as directed.

All as per item serial No 127 here-in-before but One 3 pin socket outlet 6 amps on the same board with other switches complete all as specified and as directed.

All as per item serial No 127 here-in-before but One socket outlet 3 pin 6 Amp on independent board complete all as specified and as directed.

All as per item serial No 127 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 sqmm cable complete all as specified and as directed.

Supply and fix switch modular type 6 Amp 240 Volts single one way (ISI marked) complete all as specified and as directed.

Supply and fix modular socket, 6 Amp 2/3 pin combined, 2 module complete all as specified and as directed complete all as specified and as directed.

Supply and fix modular switch 1 way 16 amp, 1 module complete all as specified and as directed complete all as specified and as directed.

Supply and fix modular socket, 16 Amp 2/3 pin combined, 2 module complete all as specified and as directed.

Supply and fix ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as specified and as directed.

Supply and fix modular lamp holder ,PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Supply and fix modular stepped type electronic fan regulator, two module size, flush type complete all as specified and as directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative batten type connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fix in repair LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed/surface type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply & fix MCB DB of sheet metal enclosure double door IP -43 SPN 8 way with 200 A rated bus bar and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate all as directed.

Supply and fix in repair for factory made, sheet steel distribution boards, IP -43 TPN, 4 Way, double door,with provision for FP MCB as incomer and SP MCBs as outgoing complete and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and as directed.

Supply and fix MCB Tripple pole & neutral 40 to 100 Amps in accordance with IS/IEC 60898-1, 415 V, 50 Hz,10 kA,B-series rupturing capacity providing in DB complete all as specified and as directed.

Supply and fix MCBs, SP 6 to 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,B-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed.

S&F MCBs, SPN 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,B-series marked fixing in DBs (DBs catered separately in this Schedule)

Supply and fix exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300mm complete all as specified and as directed.

Material and labour for Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6.mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers etc and connected to GI wire 4mm dia upto 7.5 mitre by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 15mm dia GI pipe connected to main control board and GI pipe medium grade 20mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009.complete all as specified and directed.

Cutting existing steel tubing of 40mm for alterations or additions complete all as specified and directed.

Supply and fix LED 60 W building secruity light made up of pressure die cast housing with high efficient LED as lighting source and PC cover having TOP Opening separate driver compartment with IP66 protection and impact resistance of IK07 and suitable for dia upto 43 mm complete all as specified and directed.

Material and labour for building secruity light bracket made out of 40 mm bore medium grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape for fixing street light luminaries all as directed, length of GI Pipe shall not be less than 2.0 mtrs complete all as specified and directed.

Material and labour for Sub main wiring with 2 runs of 4.0 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dia non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and type of conduit complete all as specified and directed. Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit altogether shall be measured as one unit.

Supply and fix Sheet metal enclosure for with two pin and earth plug and socket complete with SPN MCB upto 20 Amps, 240 Volts capacity and tested on complete all as specfied and directed by engineer-in-charge

Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Material and labour for XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 10 sqmm 2.0 core laid in trenches /floor or fixed on wall /pole in including brass compression cable glands, terminal lugs etc, complete all as specified and as directed.

Material and labour for XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 16 sqmm 4.0 core laid in trenches /floor or fixed on wall /pole in including brass compression cable glands, terminal lugs etc, complete all as specified and as directed.

Supply and spreading clean dry river sand in cable trenches as in cable cushioning complete all as specified and as directed. (Note: Punned thickness shall be measured and paid)

Material and labour for bricks sub class ‘B’ brick old size for cable protection laid in flat in trenches over the cable perpendicular to the direction of cable complete all as specified

V.V.Construction (BID ID -3264661)