Upgradation Of PHC Adkur for smart PHC AT-Adkur Tal- Chandgad Dist- kolhapur

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting excetra complete. - (Lift upto 1.5 metre) By Manual Means Item / Page No : 1 / 153 Specification No : Bd.A.1 Spec. Page No : 259

Providing and laying Cast in situ/Ready Mix, cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailling out water, formwork, laying/ pumping, compacting and curing, excetra complete, with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Aquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) excetra complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed, excetra) Item / Page No : 1 / 175 Specification No : Bd.E.1 Spec. Page No : 287 - 288 Additional Specifications : 1. With additional specifications for controlled concrete. 2. If artificial / VSI crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in Circular by Chief Engineer, Public Works Region, Pune bearing No CEP/D-2/Buildings-2/5940/2017 dated 17/10/2017 and Annexure-I attached to it and also Circular by Chief Engineer, Public Works Region, Nagpur bearing No 36 dated 15/01/2019 and Annexure-I attached to it will be appicable.

Providing and laying in situ/Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for reinforced cement concrete work in foundations like raft, strip foundations, grillage and footings of reinforced cement concrete columns and steel stanchions, excetra including bailling out water, formwork, cover blocks, compaction, curing and roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel), excetra complete, with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Aquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) excetra complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) Item / Page No : 11 / 178 Specification No : Bd.F.3, B-7 Spec. Page No : 298, 38-40 Additional Specifications : 1. With additional specifications for controlled concrete. 2. If artificial / VSI crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in Circular by Chief Engineer, Public Works Region, Pune bearing No CEP/D-2/Buildings-2/5940/2017 dated 17/10/2017 and Annexure-I attached to it and also Circular by Chief Engineer, Public Works Region, Nagpur bearing No 36 dated 15/01/2019 and Annexure-I attached to it will be appicable.

Providing second class burnt brick masonry with conventional / Indian Standard type bricks in cement mortar 1:6 in foundations and plinth of inner walls / in plinth of external walls including bailling out water manually, striking joints, on unexposed faces, racking out joints on exposed faces and watering, excetra complete. Item / Page No : 1 / 197 Specification No : Bd.G.1 Spec. Page No : 313 Additional Specifications : If artificial / VSI crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in Circular by Chief Engineer, Public Works Region, Pune bearing No CEP/D-2/Buildings-2/5940/2017 dated 17/10/2017 and Annexure-I attached to it and also Circular by Chief Engineer, Public Works Region, Nagpur bearing No 36 dated 15/01/2019 and Annexure-I attached to it will be appicable.

Providing internal cement plaster 20 milimetre thick in single coat in cement mortar 1:5 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing, excetra complete. (For Ground Floor) Item / Page No : 6 / 209 Specification No : Bd.L.4 Spec. Page No : 368 Additional Specifications : If artificial / VSI crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in Circular by Chief Engineer, Public Works Region, Pune bearing No CEP/D-2/Buildings-2/5940/2017 dated 17/10/2017 and Annexure-I attached to it and also Circular by Chief Engineer, Public Works Region, Nagpur bearing No 36 dated 15/01/2019 and Annexure-I attached to it will be appicable.

Providing and fixing solid core flush door shutter commercial in single leaf 32 milimetre thick without ventilator commercial type of exterior grade as per detailed drawings, with wrought iron hold fast, stainless steel fixtures and fastenings and handles on both sides and finishing with oil painting three coats, excetra complete. (For Ground Floor) Item / Page No : 10 / 246 Specification No : Bd.T.36 Spec. Page No : 500

Providing and fixing frame with / without ventilator of size as specified with non teak wood for doors and windows including chamfering, rounding, rebating holdfast of size 300 milimetre X 40 milimetre X 5 milimetre with oil painting, excetra complete. (For Ground Floor) Item / Page No : 2 / 245 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channels of 18 milimetre X 9 milimetre X 3 milimetre minimum size, crossings of mild steel flats of size 18 milimetre X 5 milimetre T or E section for runner of minimum 40 milimetre X 6 milimetre size for flange, mild steel flat for top runner of minimum size 40 milimetre X 12 milimetre with roller wheels confirming to grade F.G. 150 fitted with snap headed rivets of minimum size 6 milimetre, maximum spacing of vertical channels be 100 milimetre enclosed gate position and clear space of 150 milimetre between two sets of crossings with hold fasts, stoppers, spaces, handles, locking arrangement and one coat of red lead primer and oil painting, excetra complete. (Indian Standard : 10521-1983). (For Ground Floor) Item / Page No : 26 / 249 Specification No : Bd.T.57 Spec. Page No : 511

Providing and fixing in position (as per Indian Standard : 1868/1982) aluminium sliding window of two tracks with rectangular pipe having overall dimentsions 63.50 milimetre X 38.10 milimetre X 1.02 milimetre at weight 0.547 kilogram per running metre and window frame bottom track section 61.85 milimetre X 31.75 milimetre X 1.20 milimetre at weight 0.695 kilogram per running metre. Top and side track section 61.85 milimetre X 31.75 milimetre X 1.30 milimetre at weight 0.659 kilogram per running metre. The shutter should be of bearing bottom 40 milimetre X 18 milimetre X 1.25 milimetre at weight 0.417 kilogram per running metre. Interlocking secion 40 milimetre X 18 milimetre X 1.10 milimetre at weight 0.469 kilogram per running metre and handle section 40 milimetre X 18 milimetre X 1.25 milimetre at weight 0.417 kilogram per running metre and top section 40 milimetre X 18 milimetre X 1.25 milimetre at weight 0.417 kilogram per running metre as per detailed drawing and as directed by Engineer in-charge with all necessary aluminium sections, fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 milimetre thick plain glass with all required screws and nuts, excetra complete. - With colour anodising with box. (For Ground Floor) Item / Page No : 37 / 251 Additional Specifications : The work shall be carried out as per instructions of Engineer in charge.

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 milimetre X 38 milimetre X 1.22 milimetre box type, 5 milimetre thick sheet glass louvers of approved quality, excetra complete. (For Ground Floor) Item / Page No : 68 / 259 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing heavy duty inter locking concrete coloured paving blocks of 60 milimetre thickness of having a strength of 300 kilogramme per square centimetre of approved quality and shape on a bed of crushed sand of 25 milimetre to 30 milimetre thick including striking joints and cleaning, excetra complete. Item / Page No : 51 / 218 Additional Specifications : The work shall be carried out as per instructions of Engineer in charge.

Providing and fixing white glazed earthenware wash hand basin of 55 centimetre X 40 centimetre size including cold water piller tap / cold and hot water piller tap brackts, rubber plugs and brass chain, stop tap and necessary pipe connections including polyvinyl chloride waste pipe and trap upto the outside face of the wall.Making good the damaged surface,testing excetra complete. (For Ground Floor) Item / Page No : 63 / 272 Specification No : Bd.V.30 Spec. Page No : 565

Providing and applying interior wall finish luster of approved make on internal wall surface as detailed below scrapping the surface with emery paper and wipe clean wall primer with brush with mineral turpentine with brush 8 to 10 percent and oil 15 to 20 percent with roller and allowing to dry for a period 6 to 8 hours. wall putty with appropriate proportion of water allowing to dry for period 4 to 6 hours. Scrapping with emery paper 180 and wipe clean. Applying wall primer with brush with mineral turpentine 8 to 10 percent and oil 15 to 20 percent with roller. Scrapping emery paper 320 and wipe clean, interior wall finish luster first coat with brush/ rubber/ spray with mineral turpentine 7 to 9 percent and Oil with roller 19 to 21 percent. After 8 hours of activity, applying second coat or wall finish Lustre with mineral turpentine 7 to 9 percent with brush and Oil with roller 19 to 21 percent after allowing dry for the period of 6 to 8 hours activity. (With prior approval of S.E.) (For Ground Floor) Item / Page No : 20 / 228 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and applying plastic emulsion paint of approved quality, colour and shade to old and new surfaces in single coat including scaffolding, preparing the surface. (excluding the primer coat),etc. complete (For Ground Floor) Item / Page No : 16 / 228 Specification No : Bd.P.6 Spec. Page No : 414

Providing and applying external raincoat painting with crack filling acrylic polymer based chemical compound coating to the external surface of walls to prevent water seepage in the masonry walls during monsoon added with required shade Steiner to give required shade to the surface in two coats. Including providing three coat of priming of polymer base primer including preparing surface scrapping the existing loose old paint, removing loose particles of sand on the surface opening and cleaning the cracks developed in the external plaster, removing loose particles by chiseling, filling cracks by chemicals compound of approved make with proper penetration excetra Coating of Raincoat with the help of brush and as per instructions and specification given by manufacturer and with instruction from Engineer in-charge. Work shall be executed by certified applicator only and covering gurantee of 3 years on court stamp paper of Rs. 500/- and necessary testing, excetra complete. (For Ground Floor) Item / Page No : 29 / 226 Additional Specifications : The work shall be carried out as per instructions of Engineer in charge.

Providing and fixing unplasticised polyvinyl chloride roof made up of three layers roofing material of thickness 2 milimetre having width of 1130 milimetre and of required length having tensile strength not less than 330 kilogram per square centimetre, including fastening with self drilling screw having washers made of stainless steel, excetra complete. (For Ground Floor) Item / Page No : 37 / 237 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing polyvinyl chloride coloured ridge tiles over unplasticised polyvinyl chloride roofing where required having size 113 centimetre X 41 centimetre and height 9.5 centimetre for ridge including fastening with self drilling screw having washers made of stainless steel, excetra complete. (For Ground Floor) Item / Page No : 38 / 237 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing of colour coated zincalume (R) AZ 150 (Minimum 150 grams per square metre total on each sides) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 milimetre base metal thickness (BMT) (0.5 milimetre TCT), Hi-strength steel with minium 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55 percent aluminium, 43.4 percent zinc, 1.6 percent silicon) with COLORBOND (R) steel quality super durable polyster paint coat (with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nominal 950-1050 milimetre effective cover width and nominal 25-30 milimetre deep ribs with subtle square fluting in the five pan at nominal 180-250 milimetre center to centre. The end rib shall be designed for anti capilary groove and return leg. The feed material should have coil manufacturer's product details marked at regular interval. Including fasteners with minium fatened with minium 25 um zinc-tin alloy coated, hex head, self-drilling screw, excetra complete. (Weight of profile 4.52 kilogram per square metre). (For Ground Floor) Item / Page No : 34 / 236 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Supply of all types of Structural steel conforming to Fe 410 B of Indian Standard : 2062, Fabrication, assembling, erection / slewing / end launching of Steel girders (not requiring traffic block) upto 45.7 metre span on sub structure including provision of trolley refuges, including loading, unloading, lift and taxes complete, assembly of girders on drift / bolts, field riveting / welding, assembling of temporary support for side slewing, raising of girders to the bed block level, providing sliding arrangements (Material at site, fabrication at site, erection / launching, excetra only) - Plate Girder / Semi Through Girder. Item / Page No : 67 / 141 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing in position anodised extruded aluminium partitions having frame made out of extruded tubular section of size 65 milimetre X 40 milimetre with 12 milimetre thick three layered flat pressed teak wood particle board bonded with boiling water proof type exterior grade phenol formaldehyde synthetic resin conforming to Indian Standard : 12923-1990, laminated on both sides, Novateak or equivalent with aluminium glazing clips of size 12 milimetre X 12 milimetre (conical) as per drawing, excetra complete. (For Ground Floor) Item / Page No : 73 / 260 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and arrangemnt of mid back chair, ECO CTS mechanism, fixed armrest, gaslift for seat height adjustment, standard 5-prong P/Nylon base with fabric upholstery. Item / Page No : 43 / 359 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and arrangemnt of mid back chair, normal synchronized mechanism, fixed armrest, gaslift for seat height adjustment, standard 5-prong nylon base with leather upholstery. Item / Page No : 42 / 359 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing of free standing table of size 1350 milimetre X 750 milimetre X 750 milimetre Top to be made of 25 milimetre prelaminated particle board with polyvinyl chloride edge band, bent leg to be chrome finish as per drawing. Item / Page No : 29 / 357 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing of Executive table of size 1800 milimetre long X 900 milimetre depth X 750 milimetre height, top and gable end to be made of membrane finish with soft water fall edges and curved panel and decorated anodized section modesty panel to be made of 18 milimetre thick prelaminated particle board with polyvinyl chloride edge band as per drawing. Item / Page No : 21 / 355 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing shutters to wall cupboards made from 19 milimetre thick teak wood particle board with approved coloured laminated face on one side, 1.5 milimetre thick bonded with phenol formaldehyde synthetic resin boiling water proof grade including lipping beading iron oxidised fixtures and fastening and oil primer coat, excetra complete. (Excluding cupboard frame) (For Ground Floor) Item / Page No : 21 / 231 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing 3 seater public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish. Item / Page No : 44 / 359 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing low height openable steel storage of size 900 milimetre X 450 milimetre X 750 milimetre height with 2 adjustable shelves. Complete body and shutter made in 0.8 milimetre thick and top in 2 milimetre thick cold rolled close annealed sheet, 2 shutter to be mounted with the help of cup hinges, and 4 adjustable levelers. Enitre storage in powder coated finish with 60 microns to 80 microns, with 25 milimetre thick additional top on top of storage as as per drawing. Item / Page No : 35 / 358 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing full height openable steel storage of size 750 milimetre X 450 milimetre X 2100 milimetre height with 2 adjustable shelves. Complete body and shutter made in 0.8 milimetre thick and top in 2 milimetre thick cold rolled close annealed sheet, 4 shutter to be mounted with the help of cup hinges, and 4 adjustable levelers. Enitre storage in powder coated finish with 60 microns to 80 microns, with 25 milimetre thick additional top on top of storage as as per drawing. Item / Page No : 37 / 359 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Provoding and fixing high density polyethylen container one piece moulded water tank made out of high density polyethylen and built corrugated inclusive of delivery upto destination housing, fixing of accessaries such as inlet, outlet, overflow pipe inclusive of all Taxes - Capacity between 1000 litres to 20000 litres. (For Ground Floor) Item / Page No : 54 / 280 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing, laying and fixing polyvinyl chloride pipe of 15 milimetre diameter with fittings, such as bends, tees, reducers, clamps, excetra including necessary excavation, trench filling, excetra complete.Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed excetra complete. Item / Page No : 21 / 276 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing, laying and fixing polyvinyl chloride pipe of 20 milimetre diameter with fittings such as bends, tees, reducers, clamps, excetra including necessary excavation, trench filling, excetra complete.Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed excetra complete. Item / Page No : 22 / 276 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and laying, fixing polyvinyl chloride pipe of 25 milimetre diameter with fittings such as bends, tees, reducers, clamps, excetra including necessary excavation, trench filling, excetra complete.Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed excetra complete. Item / Page No : 23 / 276 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing, laying and fixing polyvinyl chloride pipe of 110 milimetre diameter with fittings such as bends, tees, reducers, clamps, excetra including necessary excavation, trench filling, excetra complete.Including removing existing pipe line if necessary and conveying and stacking thesame in PWD chowky or as directed excetra complete. Item / Page No : 28 / 277 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and laying matt finish ceramic tiles of having sizes 30 centimetre X 30 centimetre and confirming to Indian Standard 15622 : 2006 (Group DII-A) and 7 milimetre to 8 milimetre thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white / colour cement slurry, cleaning, curing, excetra complete. (For Ground Floor) Item / Page No : 24 / 215 Specification No : Bd.M.12 Spec. Page No : 385 Additional Specifications : If artificial / VSI crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in Circular by Chief Engineer, Public Works Region, Pune bearing No CEP/D-2/Buildings-2/5940/2017 dated 17/10/2017 and Annexure-I attached to it and also Circular by Chief Engineer, Public Works Region, Nagpur bearing No 36 dated 15/01/2019 and Annexure-I attached to it will be appicable.

Providing and laying ceramic tiles of having sizes 30 centimetre X 30 centimetre and confirming to corrosponding Indian standared for dado and skirting in required position with ready made adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white / colour cement slurry, cleanding, curing, excetra complete. (For Ground Floor) Item / Page No : 25 / 215 Specification No : Bd.M.13 Spec. Page No : 386 Additional Specifications : If artificial / VSI crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in Circular by Chief Engineer, Public Works Region, Pune bearing No CEP/D-2/Buildings-2/5940/2017 dated 17/10/2017 and Annexure-I attached to it and also Circular by Chief Engineer, Public Works Region, Nagpur bearing No 36 dated 15/01/2019 and Annexure-I attached to it will be appicable.

Providing and fixing foldable aluminium ladder 1500 milimetre height. Item / Page No : 52 / 365 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing a folding wheelchair of Pioneer Surgicals Brand, model number PS 809 or equivalent make as per the directions of the Engineer in-charge. Item / Page No : 82 / 372 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing single bed of size 2025 milimetre long X 1000 milimetre wide X 650 milimetre deep with matress and pillow. Understructure - The legs are made of square tube of size 25 milimetre X 25 milimetre made out of mild steel sheet with a thickness of 1.2 milimetre. The legs should have corner brackets welded to it at two levels. The corner brackets are made of 2 milimetre thick cold rolled close annealed sheet having a L shaped structure to join the side panels and headboard to the leg. Three numbers of horizontal stiffeners are provided at equal intervals. The stiffeners are made of square tube of size 25 milimetre X 25 milimetre made out of mild steel sheet with a thickness of 1.2 milimetre. The middle horizontal stiffener has a leg attached to it to transfer the load to the ground and add to the strength and stability of the complete structure. This leg is also made of Square tube of size 25 milimetre X 25 milimetre made out of mild steel sheet with a thickness of 1.2 milimetre. All metal components to undergo 7 tank treatment process and should be powder coated to the thickness of minimum 50 microns DFT. Side panel - The side panels are made up of 18 milimetre thick prelam particle board with both side decorative laminate. All exposed edges are sealed with 2 milimetre thick polyvinyl chloride edge banding. The overall width of the side panel is 150 milimetre. The side panels have 18 milimetre thick prelam particle board baton running for required length to add rigidity to the structure. Head board - The head board is made up of 18 milimetre thick prelam particle board with both side decorative laminate. All exposed edges are sealed with 2 milimetre thick polyvinyl chloride edge banding. The head board size to be considered as 1000 milimetre X 650 milimetre. Foot board - The foot board is made up of 18 milimetre thick prelam particle board with both side decorative laminate. All exposed edges are sealed with 2 milimetre thick polyvinyl chloride edge banding. The foot board size to be considered as 1000 milimetre X 450 milimetre. Bed base - The bed base is made up of 12 milimetre thick prelam particle board with both side white laminate. Item / Page No : 55 / 366 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing 4 legged lab stool, legs made of 16 Guage 45 milimetre outer dimension mild steel pipe, duly painted, with a 304 grade stainless steel 12 inch wide seat with a 1 inch collar, Height adjustment via a screw, as per design and drawing and instructions of Engineer in-charge. Item / Page No : 51 / 365 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and laying vitrified matt finish tiles of having size 590 milimetre to 605 milimetre X to 605 milimetre of 8 milimetre to 10 milimetre thickness and confirming to Indian Standard 15622-2006 (Group BIa) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning, excetra complete. (For Ground Floor) Item / Page No : 42 / 217 Specification No : Bd.M.12 Spec. Page No : 385 Additional Specifications : If artificial / VSI crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in Circular by Chief Engineer, Public Works Region, Pune bearing No CEP/D-2/Buildings-2/5940/2017 dated 17/10/2017 and Annexure-I attached to it and also Circular by Chief Engineer, Public Works Region, Nagpur bearing No 36 dated 15/01/2019 and Annexure-I attached to it will be appicable.

Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 milimetre to 605 milimetre X 590 milimetre to 605 milimetre of 8 milimetre to 10 milimetre thickness and confirming to Indian Standard 15622-2006 (Group BIa) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning, excetra complete. (For Ground Floor) Item / Page No : 40 / 217 Specification No : Bd.M.12 Spec. Page No : 385 Additional Specifications : If artificial / VSI crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in Circular by Chief Engineer, Public Works Region, Pune bearing No CEP/D-2/Buildings-2/5940/2017 dated 17/10/2017 and Annexure-I attached to it and also Circular by Chief Engineer, Public Works Region, Nagpur bearing No 36 dated 15/01/2019 and Annexure-I attached to it will be appicable.

Providing and fixing of factory made unplasticized polyvinyl chloride Sliding window and door (White Colour) complete, comprising unplasticized polyvinyl chloride multi-chambered frame having in-built unplasticized polyvinyl chloride roller track on top and unplasticized polyvinyl chloride sash with wall thickness of 2.3mm (+-0.2 milimetre), duly reinforced with galvanised iron section 1.5 milimetre, wherever required. unplasticized polyvinyl chloride window and door profile shall be made in India and shall conform to BS EN 12608 and other standards as mentioned below: S.No. Name of the test Test Method Specified Parameter 1 Tensile Impact Strength ISO 8256 - more than 700Kj/m2 2 Vicat Softening Temperature EN ISO – 306 Shall not be < 750C 3 Charpy Impact Strength EN ISO – 179-2 Shall not be < 20KJ/m2 4 Flexural Modulus Elasticity EN ISO – 178 Shall not be < 2200 N/mm2 5 Mean Breaking Stress for welded corner (a) For the tensile bending test EN – 514 Shall not be < 25 N/mm2 (b) For the compression bending test Shall not be < 30N/mm2 6 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 % 7 Surface Spread of flame BS : 476 - Part 7 Classification 1 8 Ignitability Evaluation BS : 476 - Part 5 'P' Not easily ignitable 9 Tensile modulus ASTM D 638 Shall not be < 35 MPa 10 Shear Modulus ASTM D 732 Shall not be < 220 MPa 11 Tensile Strength EN ISO 527 Shall not be < 30 MPa All corners of frame and sash will be fusion welded. After placing 5 milimetre Float Annealed glass in the sash, unplasticized polyvinyl chloride glazing bead, interlock, EPDM / TPE gasket, brush shall be provided including touch lock and rollers and proper drainage system shall be provided. Window / Door will be fixed to the wall with 100mm long and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-In-Charge. unplasticized polyvinyl chloride Window and Door Profiles are warranted for a period of ten (10) years against non-uniform discoloration, wrapping and rotting under general use.- 2 Track 2 / 4 Sash (Big Series) window frame of size 67 milimetre X 54 milimetre and Sash of size 85 milimetre X 47 mm Item / Page No : 8d / 516 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing mild steel grill gate with angle iron frame 65 milimetre X 65 milimetre X 10 milimetre with iron bars at 150 milimetre center to center and diagonal flats as per the detailed drawing including hinges, pivot blocks locking arrangement, welding riveting and oil painting of three coats of approved shade. Weight of gate 35 kilogram per square meter. (For Ground Floor) Item / Page No : 10 / 294 Specification No : Bd.W.6 Spec. Page No : 585 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and fixing Orissa type white glazed earrthenware 575 milimetre water closet pan including "S" trap with earthenware foot rests, cast iron soil and vent pipe upto outside face of the wall, 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories excetra complete. (For Ground Floor) Item / Page No : 30 / 277 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Providing and laying Cast in situ / Ready mix cement concrete M-20 of trap / granite / quartzite / gneiss metal for steps including steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing, excetra complete. The cement mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin, excetra (Wooden centering will not be allowed.) with fully automatic micro processor based Programmable Logic Controller with Supervisory Control and Data Aquisition enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) excetra complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) (For Ground Floor) Item / Page No : 6 / 175 Specification No : Bd.E.2, B-7 Spec. Page No : 288, 38-40 Additional Specifications : 1. With additional specifications for controlled concrete. 2. If artificial / VSI crushed sand is used instead of natural sand; terms, conditions and specifications mentioned in Circular by Chief Engineer, Public Works Region, Pune bearing No CEP/D-2/Buildings-2/5940/2017 dated 17/10/2017 and Annexure-I attached to it and also Circular by Chief Engineer, Public Works Region, Nagpur bearing No 36 dated 15/01/2019 and Annexure-I attached to it will be appicable.

Cutting down trees including trunks and branches with girths above 60 centimetre to 90 centimetre and stacking the material neatly with all lift and lead of 1000 metre, as directed and earth filling in the depression / pit, if any. Item / Page No : 2 / 23 Specification No : MORTH-201 Spec. Page No : 37-39

Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts excetra complete. Item / Page No : 19 / 297 Additional Specifications : The work shall be carried out as directed by Engineer-In-Charge.

Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 milimetre with lock plate of 3.15 milimetre thickness reinforced with 35 milimetre X 35 milimetre X 5 milimetre angle section fitted with sliding bolts and handles for both sides, deep mild steel channel section of depth and thickness not less than 65 milimetre and 3.15 milimetre respectively with hold fast arrangements, mild steel bracket plate 300 milimetre X 300 milimetre X 3.15 milimetre minimum size and shape with square bar, suspension shaft of minimum 32 milimetre diametre, hood cover of mild steel sheet not less than 0.9 milimetre thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer, excetra complete. (Indian Standard : 6248-1979) - without mechanical gear (For Ground Floor) Item / Page No : 24 / 248 Specification No : Bd.T.55 Spec. Page No : 510

Providing and fixing of Soft Fibre Acoustical Suspended Ceiling System with Optra (Bevelled Tegular) Edge Tiles With 15 milimetre Exposed Grid. The tiles should have Humidity Resistance (RH) of 95 percent, NRC 0.9 - 1.0, Light Reflectance .85 percent, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 600 X 600 X 15mm , suitable for Green Building application, with Recycled content of 66 percent GW and 74 percent RW. The tile shall be laid on precoated G.I channel 32 with 15 milimetre wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 milimetre and 600 milimetre Cross Tees with a web height of 32 milimetre and a load carrying capacity of 7 Kgs/M2 with a minimum pull out strength of 100 kgs. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system The Tile and Grid system used together should carry a 10 year warranty. products approved as per GRIHA and BS 476, excetra complete. Item / Page No : 47 / 242 Additional Specifications : The work shall be done as per instructions of Engineer in charge.

Add Insurance Towards Labour @1.00% Non-Dsr Item Additional Specifications : The work shall be carried out as per the instructions of Engineer in-charge.

Goods and Services Tax @ 18% Item / Page No : 15 / 0 Additional Specifications : The work shall be carried out as per the instructions of Engineer in-charge.

Please Enable Macros to View BoQ information