REPAIR TO JOINERY, FALSE CEILING AND ALLIED WORK IN TECH AREA AT AFS CHAKERI KANPUR

Amount

Taking down chowkats or frames with shutter not exc 1.5 sqm each (without taking off shutters from the frame) complete all as specified and directed.

All as per item No 1 but exc 1.5 sqm but n.exec 4sqm each.

Taking down shutter of any description exc 1 sqm but n.exec 2 sqm each.

All as per item No 3 but exec 2 sqm each.

S&F for steel ventilator with guard bar and top hung shutter including hinges, steel peg stay, complete all as specified and shown on drawing No CE (AF)/NGP/TD-89/2007 Sheet No 1/9 to 9/9. (sheet glass shall be measured and paid separately

S&F for openable double shutter steel windows i.e. glazed and gauged with side hung shutters including projecting type hinges with steel hinges with steel handles, and steel peg stay, completely with glazing bars, dovetailed or welded joint including PCC 1:3:6 type C-2 filling as in back side of frame, complete all as per detail shown on drawing No. CE(AF)NGP/2003/TD/08 sheet no. 1/12 to 12/12. Note-(i) MS grill shall be measured and paid separately under relevant item. (ii) Wire mesh and glazing including sheet glass shall be measured and paid separately under relevant item

S&F for 1.25 mm thick pressed steel frames for doors with one/more rebated incl necessary fixing lugs hinges lock strike plate etc complete size 125x60mm and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkats complete all as specified and directed

S&F for 35 mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed

S&F 35 mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both sides including both faces covered with decorative face veneer with lipping / frame to match complete all as specified and directed

M & L for preparation of new previously untreated surface of wooden wood based materials of any description over 10cm girth or width not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F Factory Made Solid PVC Moulded Door Shutter,28 to 30 mm thick 'Stiles' with 2, 4, or 6 raised panel design with 2 mm thick Moulded Prelam PVC sheet on the front face and 2 mm prelam PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing.

M&L Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for door with chowkhat /frame made with aluminium section with size 100x44x2mm thick and shutter of vertical style with section 84x44x2mm thick and top /middle / bottom rails of shutter made with 112x44x2mm thick over and including 5mm thick tinted glass panes, including necessary fixing arrangment ,joining cleats, glazing clips, rubber beading, floor door spring, tower bolts 200mm long, mortice lock 300 mm, 4 lever, rounded handles etc fixed to shutters complete all as specified and directed by engr in charge.

S&F 150 mm long aluminium handles , cast type, anodised complete all as specified and directed

S&F 100mm size butt hinges stainless steel of AISI 304 complete all as specified and directed.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed

S&F aluminium alloy, anodised 250 mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples etc complete all as specified and directed.

S&F in repair 150 mm Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed

S&F in repair 150 mm long aluminium handles , cast type, anodised complete all as specified and directed

S&F in repair mild steel butt hinges , medium weight,cold rolled mild steel size of 100mm long .complete all as specifiedand directed

S&F in repair aluminium alloy, anodised 250 mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

Taking down easing and adjusting shutters of any description exec 1 sqm but n exc 2 sqm each refixing in same opening, all as specified and as directed.

All as per items 24, here-in-before, but exc 2 sqm each refixing in same opening complete all as specified and directed

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples etc complete all as specified and directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded agg) for hold fasts finished to match with the sorrounding surfaces including necessary form work complete all as specified and as directed.

S&F in repair mortice lock brass 4 levers vertical type, size 100mm complete all as specified and directed.

S&F in repair 150 mm over all length of cover plate of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F in repair 150 mm over all length of cover plate of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

S and F in repairs aluminium (die cast) body door closer hydraulically regulated designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed

Supply and fixed aluminium (die cast) body door closer hydraulically regulated designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg.

S & F in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheed, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed

Taking down easing and adjusting aluminum shutters including complete accessories of any description exc 1.5 sqm but not exc 4 sqm each refixing in same opening, all as specified and as directed. Note :- Replacement of door closer, glass, lock, handle, tower bolt etc shall be measured and paid separately. Note: Taking down aluminium door and refixed after fixing floor spring including making good etc deem to be included in quoted rate.

Demolition of brick work or stone masonry built in cement mortar including all quoines arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed

All as item No 36 above but except bricks complete all as specified and directed

M&L for rendering 15mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick on other than fair faces of brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified.

Taking down cement plaster on bricks or stone walls etc., including raking out joints, hacking for key scrubing down with water etc. complete all as specified and directed.

M&L for preparation of new undecorated surfaces of walls and applying two coat of Oil Bound Distemper over a coat of primer and 1mm thick wall care putty complete all as specified and directed

M&L for preparation of new undecorated surfaces of walls and applying two coat of cement based paint over a coat of primer complete all as specified and directed

Dismantling of wall and ceiling boards any type (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets any thickness including cover fillets all as directed.

S&F 16mm thick of size 600 x 600 mm mineral fibre false ceiling system of pattern classic lite RH 99 (bevelled tegular ) of Armstrong or equivalent make and model including grid system using hot dipped galvanised steel section, exposed surface with pre-powder coated capping ,main runner and cross runner and to comprise main tee/runner 15 mm x 38mm size (load carring capacity 14 kg /sqm ) spaced at 1200 mm centres securely fixed to the structural sofit and flush fitting 1200 mm long cross tee/runner to be interlocked between main runners at 600 mm centre to centre from 1200 x 600 mm module , cut sub cross tee/runner 600mm require independent support ,wall angle of size 19mm x 19mm secured to the periphery of the wall at 450 mm maximum centre the above grid is suspended at every 1200 mm centre to centre in both direction and starting from wall at the distance 350mm, complete all as specified and directed

Supply and fixing false ceiling at all heights with semi perforated 12mm thick micro tegular edged GRG (Glass fibre Reinforced Gypsum) false ceiling tiles of size 595 x 595mm of approved texture, design and pattern having moister content less than 2%, humidity resistant of 99%, NRCO.50 to 0.75 as per IS 8225:1987, noncombustible as per BS 476 (part 4) - 1970 and light reflectance of 85% minimum to be laid in true horizental level suspended on inter-locking metal T-Grid of hot dipped galvanised ireon section of 0.33mm thick (galvanised @120gm/Sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm, cross T of size 15 x 32 mm of length 1200mm and secondary intermediate corss T of size 15 x 32 mm of length 600mm to from grid module of size 600x 600 mm suspended from ceiling using galvanised mild steel items (galvanised @ 80gm/Sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450mm centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specifiection, drawing and as per directed of Engineer-in-Chagre.

Refixing only the depressed/sagged portion of existing false ceiling grid system of any description after taking down existing ceiling board of any description and refixing the same in position. Note- The quoted unit rate include supply and fixing 4 mm dia GI bar hanger and fly clip if required in refixing.

S&F 16 mm thick of size 595 x 595mm or 600 x 600 mm mineral fibre false ceiling board of pattern classic lite RH -99 (Bevelled tegular) of armstrong or equivalent make Specified including taking down old ceiling board from existing snap grid complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise sepcifically provied for including existing roof treatment (tarfelt) including removing to a distance exc 1.50 KM but not exc 5.00 KM complete all as specified and directed

M & L for cement concrete type C1 1:3:6 (20 mm graded aggregate) in copings, plinth protection courses, string courses and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for sheet glass 3mm thick glass ground or obscured or frosted, on one side glazing with oil putty in square n. exec 0.5 Sqm in each pane including hacking out old broken/unserviceable glass complete all as specified and as directed.

Hacking out old glass (any thickness) from aluminium door shutter with rubber beading / aluminium beading and refixing the same glass after the change of new rubber beading and tightening the same complete all as specified and directed.

Hacking out old glass (any thickness) from aluminium door shutter with rubber beading / aluminium beading and fixing new glass 5 mm thick with new rubber beading and tightening in existing door shutter complete all as specified and directed.

S&F in repair Prelaminated particle board, 12 mm thick exterior grade, prelaminated on both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise described for, complete all as specified and directed.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooksand hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) andhanging; also fastening and fixing complete all as specified and as directed.

S&F for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed

S&F 1.25 mm thick Mild steel, plain, blacksheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bendingor turning up, mitred angles, etc. as required complete all as specified and directed

S&F in repair Steel rolling shutters with thickness of lathe 1.25 mm, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel pain complete all as specified and directed.

Baba Siddhnath Construction (BID ID -3109967)

B R CONSTRUCTIONS (BID ID -3117742)