Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹41.0 LAccepted-AOC AT PO DERA COLLIERY TALCHER DIST ANGUL ODISHA PIN 759103 | ANUGUL | ODISHA | 759103 | L1 | Accepted-AOC Being L1 | |
| 2 | L2₹47.0 L+₹5.7 L (13.9%)Rejected-Finance 20 8 EWS PREETAM NAGAR COLONY ALLAHABAD | PRAYAGRAJ | UTTAR PRADESH | 211001 | L2 | Rejected-Finance Being L2 | |
| 3 | L3₹47.4 L+₹6.2 L (15.0%)Rejected-Finance 41B 1H JAYANTIPUR PREETAM NAGAR ALLAHABAD | L3 | Rejected-Finance Being L3 | |
| 4 | L4₹49.6 L+₹8.4 L (20.4%)Rejected-Finance | L4 | Rejected-Finance Being L4 |
Tender Value
₹49 L
EMD Value
₹98,000
Closing Date
20 Jul 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Garrison Engineer (East) Allahabad
Stanley Road, Teliyarganj, Allahabad
SPL REPAIR OF OLD VINTAGE BLDG AND BER EQUIPMENT AT OD FORT AND PROVN OF 02 X ROOMS WITH TOILET AT FD HOSP AT OLD CANTT ALLAHABAD
2022_MES_528567_1
8561/E8
Open Tender
Civil Works
Item Rate
180 days
Allahabad
As Per NIT
8 documents required · 8 mandatory
₹500
Yes
GE (East) Allahabad
₹98,000
Yes
5 Sept 2022
4 Jun 2022
22 Jul 2022
4 Jun 2022
20 Jul 2022
22 Jun 2022
4 Jun 2022 - 11 Jun 2022
60 days
Amount
Taking down cement plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water including removing of all rubbish off from the site, complete all as specified and directed.
Rendering 15mm thick in CM 1:4, mixed with water proofing compound, on fair faces of brick work or concrete surfaces of walls, finishing the surface even and smooth without using extra cement, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.
Preparation of new plastered surfaces of walls and applying two coats of cement base paint of approved colour over a coat of cement primer, complete all as specifed and directed.
Demolition of cement oncrete (un reinforced) of any description and in any position not secifically provided, complete all as specified and directed.
Plain cement concrete 1:3:6, type C2 (using 40 mm graded crushed stone aggregate), 75mm thick as in plinth protection, finsihed even and smooth without using extra cement, inlcuidng making joints 12mm wide to the full depth of PCC at every 3 metre and at every change of direction and filling the same with and including provision of bitumen and sand mixture at 1:3 proportion, complete all as specified and directed.
Taking down chowkats or frames not exceeding 1.5sq.m each with shutters (without taking off shutters from the frames) including removing from site, complete all as specified and directed.
Solid PVC Double door frame of size 50mm x 100mm made out of 5mm single side prelam sheet reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.
Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.
Brass extruded type 150mm long barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed, complete all as specifed and directed.
Extruded brass handles, fabricated type polished, 150mm long, complete all as specified and directed.
Brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed , 300mm long, complete all as specifed and dirceted.
Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11, 100mm size, complete all as specified and directed.
Vitreous China wash basin, with full pedestal of size 830mm x 560mm x 480mm, white, flat back type, excluding tap but including brackets, fixed in repair, comnplete all as specified and directed. Make: Parryware Cat Part No ARS-WHT-1509 or techno-commercially equivalent model in Jaguar/ Cera.
Central hole wash hand basin mixer without popup waste system with 450mm long copper pipes and brass nuts, fixed in repair, complete all as specified and dirceted. Make: Jaguar Cat Part No FLR 5169NB or techno-commerically equivalent model in any make as approved by GE.
Bottle trap (with internal partition), 32 mm dia with 250mm long wall connection pipe and 190mm long wall flange, fixed in repair, complete all as specified and directed. Make: Jaguar Cat Part No ALD-769L 250 x 190 or techno-commerically equivalent model in any make as approved by GE.
CP wall mixer 3 in 1 system with provision for both telephone shower and overhead complete with 15mm bore bend pipe and wall flange, fixed in repair, complete all as specified and directed. Make: Jaguar Cat part No FLR 5281N or techno-commerically equivalent model in any make as approved by GE.
Shower rose with shower arm 20mm dia and 300mm long round shape with 90o bend for wall mounted showers with stainless steel flange, complete all as specified and directed. Make: Jaguar Cat Part No SHA-479L300S or techno-commerically equivalent model in any make as approved by GE.
Towel ring 200mm dia, Chromium plated, fixed in repair, complete all as specified and directed. MAKE:- Jaguar Cat No. ACCN-1121BN or techno-commercially equivalent model in Parryware or Cera.
Towel rack 600mm long, CP, with bottom hook, fixed in repair, complete all as specified and directed. Make: Jaguar Cat Part No: CAN-1181FHN or techno-commercially equivalent model in Parryware or Cera.
Stop / Angle valve, 15mm dia, fancy type, CP, with long shank and cup (concealed type) etc, complete all as specified and directed. MAKE:- Jaguar Cat No. FLR-5053N or techno-commercially equivalent model in Parryware or Cera.
Toilet paper holder with stainless steel flap fixed to wall etc, complete all as specified and directed. MAKE:- Jaguar Cat No. CAN-1153S or techno-commercially equivalent model in Parryware or Cera.
Soap dish, fancy type, CP, fixed in repair, complete all as specified and directed. MAKE:- Jaguar Cat No. 1131N techno-commercially equivalent model in Parryware or Cera.
Hand shower (Health faucet) with 8mm dia 1.20m long flexible tube and wall hook with NRV including fixing bracket, fixed in repair, complete all as specified and directed. MAKE:- Jaguar Cat No. ALD-577 or techno-commercially equivalent model in Parryware or Cera.
Cast Iron 'P' or 'S' trap, 100mm bore, complete all as specified and directed.
Cast Iron sanitary connection socket of size 100 mm to fit the WC outlet, complete all as specified and directed.
Door closer hydraulically regulated, Aluminium die cast, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, fixed in repair, complete all as specified and directed.
Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore, fixed in repair, complete all as specified and directed.
Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25 mm bore, fixed in repair, complete all as specified and directed.
Stop valves, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, 15mm bore, complete all as specified and directed.
Rotational moulded HDPE water storage tanks (cylindrical vertical with closed top), 500 litre capacity (ISI embossed), double layered, hoisted and fixed in position all as specified in SSR Part I, including provision of GI nipple for tank, fixed in repairs, complete all as specified and directed.
Ball brass valves, 20 mm dia, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed.
CP grating, 100mm dia, fixed with coloured cement, joint to match the existing surface of tile, fixed in repair, complete all as specified and directed.
Soap dish of size 100mm x 50 mm, oval shaped, chromium plated, fixed to wall with PVC gully and CP screws, fixed in repair, complete all as specified and directed.
PVC connections 15mm size, of length 450mm, both ends having PTMT nuts, fixed in repairs, complete all as specified and directed.
Taking up or down 15mm bore, steel tubing and connections, , including cleaning for refixing or removal to store, complete all as specified and directed.
Taking up or down 20mm bore, steel tubing and connections, , including cleaning for refixing or removal to store, complete all as specified and directed.
GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 15mm bore of pipe, complete all as specified and directed.
GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 20mm bore of pipe, complete all as specified and directed.
GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 25mm bore of pipe, complete all as specified and directed.
GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 15mm bore of pipe, complete all as specified and directed. [Except tubing]
GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 20mm bore of pipe, complete all as specified and directed. [Except tubing]
CP fancy type, bib cock, long body, half/ full turn including flange screwed down for iron pipe 15mm bore, fixed in repair, complete all as specified and directed. Make: L&K Cat No 0047 or techno-commerically equivalent model in any make as approved by GE.
Demolition and breaking up AC drain pipe of any internal dia, set in cement mortar, complete all as specfied and directed.
PVC (SWR) 110 mm bore pipes single socketed ends, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed..
PVC (SWR) 110 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.. Note : Stack clamps for fixing in walls shall be included in the quoted rates.
PVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed..
PVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.. Note : Stack clamps for fixing in walls shall be included in the quoted rates.
PVC (SWR) bends / shoe of any radius and 110mm bore, complete all as specified and directed..
PVC (SWR) bends / shoe of any radius and 75mm bore, complete all as specified and directed..
PVC (SWR) vent cowl, 110mm bore, complete all as specified and directed..
PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified and directed.
PVC (SWR) floor trap, plain jointing with solvent cement, 75mm bore, complete all as specified and directed.
Preparation of new plastered or unplastered surfaces of walls and applying two coats of acrylic emulsion paint in approved shade over a coat of primer, complete all as specifed and directed.
Preparation of new plastered or unplastered surfaces of walls and applying two coats of acrylic emulsion paint in approved shade over 2mm thick wall care putty including a coat of chalk whiting, complete all as specifed and directed.
Preparation of new plastered or unplastered surfaces of walls and applying two coats of acrylic emulsion paint in approved shade over 2mm thick wall care putty, complete all as specifed and directed.
Preparation of new plastered or unplastered surfaces of walls and applying two coats of weather coat paint in approved shade over a coat of ready made cement primer over 1mm thick wall care putty, complete all as specifed and directed.
Preparation of new steel and iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.
Concrete bed to 150 mm bore drain pipes including packing under and haunching against the sides of pipes, in PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate), complete all as specified and directed.
Reinforced concrete pipes, 150mm bore, class NP-2, laid and jointed complete with collars, complete all as specified and directed.
Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm dia pipe, complete all as specified and directed.
Precast reinforced cement concrete as in cover slabs (for manholes) chullah hoods, chajjas, water trough, mangers, shelves and other similar works, type B-1, 1:2:4 using 20 mm graded aggregates set in cement mortar 1:6, complete all as specified and directed. Note: Reinforcement to be measured and paid separately.
Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store, removing rubbish off the premises, complete all as specified and directed.
Vittrified Ceramic coloured tiles 9-10 mm thick, in light shade, size of each tile shall be 600mm x 600mm, as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. Make: Marbonite (Series-2) of M/s H&R Johnson Ltd or techno-commercially equivalent model in any make approved by GE.
Vittrified Ceramic coloured tiles 9-10 mm thick, in light shade, size of each tile shall be 600mm x 600mm, as in vertical surfaces such as steps/ dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 10 mm thick rendering in CM 1:4, complete all as specified and directed. Make: Marbonite (Series-2) of M/s H&R Johnson Ltd or techno-commercially equivalent model in any make approved by GE.
Non - skid Ceramic, coloured tiles 7 to 8 mm thick, size of each tile shall be 400mm x 400mm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 15 mm thick screed bed in CM 1:6, complete all as specified and directed.
Glazed ceramic coloured tiles as in vertical surface of walls such as skirting / dado and risers to steps, size of tile shall be 350mm x 250mm x 7mm / 450 x 300 x 7 mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles, laid over and including provison of 10 mm thick rendering as in backing coat of tiles in cement mortar 1:4, complete all as specified and directed.
Plain cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate), as in mass concrete in foundation filling, complete all as specified and directed.
Vitrified exterior coloured flooring tiles of 300 mm x 300 mm size, laid in floors with cement based adhesives, set and jointed as per manufacturer's instructions over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. Make: Orient Bell Ltd Cat Part No Checkers Teracotta (16513) or equivalent
Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded in any mortar, complete all as specified and directed.
Granite, 20mm thick, (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20 mm thick screed bed in CM 1:4, complete all as specified and directed.
Demolition of mud/lime concrete in roofs, any thickness, including plastering, old water proofing membrane and and leeping including brick/brick tiles (whether full thickness removed or only a part thereof) and removing the rubbish from site for distance not exc 50m, complete all as specified & directed.
Dismantling Bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer) laid and bedded pointed in cement mortar, complete all as specified and directed.
Plain cement concrete 1:2:4 type B-0 (12.50mm graded stone aggregate), as in levelling course, benching etc., and finished the surface even and rough to receive screed bed, complete all as specified and directed.
Screed bed 10mm thick in CM 1:3, mixed with water proofing compound, over roof slab, finishing the surface even and fair, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.
Providing water proofing treatment over cleaned roof surface with bitumenous membrane weight not less than 3 kg per sq.m comprising of the following and testing of following: (a) Removing existing roof treatment & cleaning roof surface and applting One coat of Bitumen primer confirming to IS-3384-1965 @ 0.3 kg per sqm. (b) Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sq.m confirming to IS-702-1998 for water proofing membrane. (c) Providing APP modified polymeric water proofing membrane having weight not less than 3 kg per sq.m with 100 mm wide side or end lap and joint sealed with flamed torched pasted over full length. (d) Applying one coat of bitumenious aluminium paint over water proofing membrane.
Bricks, sub class "B", laid flat on roofs, old size bricks bedded and jointed in CM 1:6 and pointed flush in CM 1:3, bricks bedded on 25mm thick sand layer, complete all as specified and directed.
Bricks, sub class "B", laid flat on roofs, old size bricks bedded and jointed in CM 1:6 and pointed flush in CM 1:3, bricks bedded on 25mm thick sand layer, complete all as specified and directed. [Except bricks]
Supply only integral water proofing compound, complete all as specified and directed.
Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3, complete all as specified and directed.
Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.
Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks or supporting stand for desert coolers etc., and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.
Providing and fixing E-board Make: Everest, Design "Lake and Hill" of size 605 x 605 x 4mm thick white prelaminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section (White powder coated). The framework shall comprise of main runner made from 0.33mm thick GS sheet and of size 24 x 32 x 300mm and secured at 1200mm maximum centres securely fixed to structural soffits with hangers of 2mm dia GI wire to be fixed with approved rawl plugs, adjusters and screws. Flush fitting of 1200mmm long cross Tee (with double stiching) to be interlocked between main runners at 600mm centre to form 1200 x 1600 mm modules cross tee longer than 600mm to be supported independently. 600 x 600mm doubles to be formed by fittings 600mm long cross tee centrally between the 1200mm cross tee. Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19 x 19 mm and 300mm long of white colour all as per manufacturers instructions, fixed in reapir, complete all as specified and directed. Make of Frame work : Armstong or equivalent
Aluminum window/ CSW/ Ventilator (Sliding type) with aluminum anodized frame of aluminum section 62.5 x 37 x 1.5 mm thick including jointing cleats, glazing clips, rubber packing, aluminum snap beading, screws anodized aluminum fittings such as hinges, tower bolts, handles etc, including both side prelaminated aluminium board, fixed in repair, complete all as specified and directed.
Aluminum door with aluminum anodized frame of aluminum section 62.5 x 37 x 1.5 mm thick with shutters having styles & rails of aluminum section 47.62 x 44.45 x 1.5 mm thick including jointing cleats, glazing clips, rubber packing, aluminum snap beading, screws anodized aluminum fittings such as hinges, tower bolts, handles etc including 5.5 mm thick frosted glass and prelaminated particle board in lower portion, fixed in repair, complete all as specified and directed.
Aluminium anodised grill with mesh of specified shape and size fixed with beeds and stainless steel screws, complete all as specified and directed.
Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete all as specified and directed.
Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, complete all as specified and directed.
Aluminium composite panel, 3mm thick with 0.3mm alloyed aluminium skin sheet with PVDF coating fixed in position in the shape and design as directed. The joints of panels shall be sealed by high performance structural silicon sealant tapes, complete all as specified and directed. Make: Aepotic, Alcobond, Renybond, Indobond or or techno-commercially equivalent model in any make approved by GE.
Toughened glass railing, 10mm thick, of Make: SAFEX/ SIVTUFF/ OLYMPUS, solid tempered toughened glass fixed with SS screw including making holes and smooth rounding on glass edges complete SS railing grade 304 make- Jindal or equavalent top rail hollow tubular stainless steel rail tubular baluster of size 40mm x 40mm grade 304 fixed at centre to centre distance 1.0meter and tubular pillar of SS grade 304 size 75mm x 75mm fixed at center to centre distance 6.0meter fixed with SS bracket including necessary fixing arrangements with block of PCC (1:3:6) type C1 of 30cm x 30cm x 45cm deep complete all as specified and directed. Note : The railing shall be measured in horizontally outer to outer. All fittings and fixtures are deemed to be included in overall length. Complete all as specified and directed by Engineer-in-Charge.
Stainless steel decorative railing of 50mm dia of wall thickness 2.0mm thick (heavy duty) of 900mm height including necessary fixing arrangements with block of PCC (1:3:6) type C1 of 30cm x 30cm x 45cm deep complete all as specified and directed . NOTE: (i) Top and bottom rail of 50mm dia of wall thickness 2.0mm thick. (ii) 5 Nos of horizontal rail shall be of 25mm dia and 1.50mm thick. (iii) Baluster vertical shall be of 40mm dia of wall thickness 2.0mm thick of 1.0 meter centre to center. (iv) Main baluster vertical shall be of 50mm dia of wall thickness 2.0mm thick of every 3.0 metre centre to centre. (v) The raling shall be measured in horizontally outer to outer. All fittings and fixtures are deemed to be included in overall length.
Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft/ loose soil, complete all as specified and directed.
Excavation in trenches not exceeding 1.5m deep and not exceeding 1.5m wide or area not exceeding 10 sq.m on plan and depth not exceeding 1.5 m for foundation, for shafts, wells, cesspits, manholes, pier holes etc., and getting out in any type of soil, complete all as specified and directed.
Returning, filling in soils, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick, complete all as specified and directed.
Removing of surplus excavated material to a distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and directed.
Brickwork with flyash bricks, old size straight or curved on plan exceeding 6 metre mean radius, built in CM 1:6, complete all as specified and directed.
Brickwork with flyash bricks, old size straight or curved on plan to any radius in half brick walls, built in CM 1:4, complete all as specified and directed.
RCC M-25 (design mix) using 20mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.
RCC M-25 (design mix) using 20mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.
RCC M-25 (design mix) using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.
RCC M-25 (design mix) using 20mm graded stone aggregate as in beams, beam haunchings, girders, bressummers, lintels, cantilevers, lintetls over 1.5 m span, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.
RCC M-25 (design mix) using 20mm graded stone aggregate in Chajjas, complete all as specified and directed. Note: Reinforcement shall be measured and paid separately.
TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.
TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, complete all as specified and directed.
Formwork to rough finished sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and directed.
Formwork to rough finished square, rectangular, polygonal surface of concrete in sides of pillars, posts, struts, piers, columns and stanchions, complete all as speciifed and directed.
Formwork to rough finished sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc., complete all as specified and directed.
Formwork to chullah hoods, chajjas, troughs and similar items including edges for flat rough finished surface of concrete, complete all as specified and directed.
Formwork to flat rough finished surface of sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.complete all as specified and directed.
Spreading, levelling, watering and well ramming earth in layers n exc. 25 cm thick infloor filling, complete all as specified and directed.
Sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.
Hardcore, of broken stone or boulders, of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.
Plain Cement concrete 1:4:8 type D-2 (using 40 mm crushed stone aggregate), 75mm thick, as in sub base of floor, complete all as specified and directed..
Plain Cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate), in plinth protection, 75mm thick, complete all as specified and directed.
Rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of walls, finishing the surface even and smooth without using extra cement, complete all as specified and directed.
Rendering 5mm thick in CM 1:3 on concrete surfaces of ceilings, finishing the surface even and smooth without using extra cement, complete all as specified and directed.
Solid PVC Door Frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5mm thick rigid PVC foam sheet, mitre cut at two corners and joined by inserting 2nos. of 150mm long brackets of 15x15mm M.S. square tube, the door profiles are to be reinforced with 19 x 19 mm M.S. Square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame, The door frame shall be fixed to wall using 65/100 mm long MS screws through the frame using PVC fasteners, a miniumum of 4 screws to be provided for each vertical member and minimum of 2 screws for each horizontal members, all as per manufacturer's instructions, complete all as specified and directed. MAKE:- Sintex / Rajshree plastic / Wood Forex, Indore
Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification, complete all as specified and directed. MAKE:- Sintex / Rajshree plastic / Wood Forex, Indore / M/s Kumar Arch Tech Ltd.
Pressed steel frames for doors of size 105mm x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed, complete all as specified and directed.
Pressed steel frames for doors of size 125mm x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed, complete all as specified and directed.
Glazed and skeleton shutters, 35mm thick, second class hardwood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), divided into squares with plain, chamfered or rounded mitered beads for securing glass/gauge complete all as specified in SSR Pt- I, section 8, clause 8.24(a) and as directed. Note: Glass or wire cloth, etc. in panels or sash squares shall be measured separately.
Flush shutters 30 mm thick, factory made, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.
PCC 1:3:6 type C-1 (using 20mm crushed stone aggregate) as in fixing of hold fasts with and including provision of necessary form work if required complete all as specified and directed..
Butt hinges, medium weight, cold rolled mild steel, and fixed, 100mm size, complete all as specified and directed.
Aluminium powder coated handle 150mm size of extruded scetion, complete all as specified and directed.
Aluminium powder coated tower bolt 150mm size of extruded section, complete all as specified and directed.
Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed 300mm long, complete all as specified and directed.
Steel ventilator with top hung shutter including hinges, steel peg stay, complete, fixed in repairs, complete all as specified and directed.
Powder coated aluminium window shutter sliding type with 3 track (one shutter with aluminium jallie sliding type and 2 shutter with glass pan) without sash bar with stile and rail of size 45 x 45 x 1.8 mm thick including 4mm thick sun reflected sheet glass and necessary, glazing clip, rubber packing with and including following fittings: (i) Aluminium handle 200mm - 02 Nos (ii) Aluminium tower bolts 200mm size - 02 Nos
Sheet glass, 4 mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete as specified & directed.
Vitreous China wash down water closet pan (pedestal pattern) , white (excluding flushing cistern and flushing pipe), white, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device, UPVC (SWR) 'P' or 'S' trap and connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc., complete all as specified and directed. NOTE:- Plastic seat cover shall be measured as Supply only under respective item of this Schedule.
Supply only plastic seat cover for water closet, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.
PVC valveless, syphonic action type, flushing cistern, 10 litre capacity, low level, white, with inlet, ball valve, float and handle, jointing with and including provision of 32mm dia 600mm long flush pipe and connections to pipes and fixing of chain and pull, or lever, if any, complete all as specified and directed.
Vitreous china wash hand basin white flat back of size 630mm x 450mm excluding chain, plug and porcelain stopper but including brackets and cutting for and pinning in ends of brackets, fixed in repair, complete all as specified and directed.
Bib taps (fancy type), cast copper alloy, long body chromium plated with crutch or butterfly hnadle, screwed down, screwed for iron pipe or for brass ferrule and fixed, 15mm bore, fixed in repairs, complete all as specified and directed.
Stop valves, cast copper alloy, fancy type, chromium plated (concealed type), with chromium plated wall flange, screwed down, high pressure, long shank and exposed part kit with fitting sleeve, operating lever concealed part, screwed both ends for iron pipe or for unions and fixed, 15mm bore, fixed in repairs, complete all as specified and directed.
Angle valves, cast copper alloy, fancy type, chromium plated (concealed type), with chromium plated wall flange, screwed down, high pressure, long shank and exposed part kit with fitting sleeve, operating lever concealed part, screwed both ends for iron pipe or for unions and fixed, 15mm bore, fixed in repairs, complete all as specified and directed.
PVC connection 15mm size with brass checknuts and washers on both ends of length 450mm, fixed in repair, complete all as specified and directed..
Pillar taps cast copper alloy with capstan head chromium plated fancy type screwed down high pressure with or without lettered 'HOT' or 'COLD' letter with long screwed shank and fly nuts, screwed for iron pipe 15mm bore pipe, complete all as specified and directed.
Waste coupling of PTMT (half or full threaded), 32 mm dia, complete all as specified and directed.
Tubular towel rail brass chromium plated, 20mm dia, 'D' type, 600mm long, fixed with two plugs of second class hardwood embedded in CM 1:3., complete all as specified and directed.
French polishing on new wood surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two coats of polish, complete all as specified and directed.
Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed.
Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc., complete all as specified and directed.
Taking down switches, distribution boards and old cut-outs etc., of any type and carefully along with the existing boards and removing the same from site and making good disturbed surfaces of walls to match with the existing, complete all as specified and directed.
Taking down carefully sub-main wiring of any type and any numbers including earthwire surface type / concealed type and removing the same from site and making good disturbed surfaces of walls to match with the existing, complete all as specified and directed.
Point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 1.5 sq.mm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring, including provision of concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside and outside with two coats of black bituminous paint over and including a coat of red oxide primer, with 2.8 mm thick top cover of plastic lmainated sheet of required colour for mounting switch, sockets, fan regulator etc, including 1.5 sq.mm FRLS type PVC insulated unsheathed cable multi stranded copper conductor as continuous earth wire and connected to earth dolly as required at site and including chases cutting and making good the disturbed surface and applying finishes to match the existing surface, complete all as specified and directed for the following:-
(a) One light / fan / bell / exhaust fan point, controlled by one one-way 5Amp switch
(b) One 5 pin, 5 Amp socket outlet point on an independent board.
(c) One 5 pin, 5 Amp socket outlet on the same board with other switches
Point wiring complete with PVC insulated unsheatehd, 1100 volts grade cable 2.5 sq.mm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one 6 pin 15/16 Amps socket outlet on an independent board including provision of concealed opressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside and outside with two coats of black bituminous paint over and including a coat of red oxide primer, with 2.8 mm thick top cover of plastic lmainated sheet of required colour for mounting switch, sockets, fan regulator etc, including 2.5 sq.mm FRLS type PVC insulated unsheathed cable multi stranded copper conductor as continuous earth wire and connected to earth dolly as required at site and including chases cutting and making good the disturbed surface and applying finishes to match the existing surface, complete all as specified and directed.
Sub main wiring complete with 2 runs of 6 sq.mm PVC insulated and unsheathed 1100V grade multistranded FRLS grade copper conductor cable drawn through and including provision of rigid PVC conduit 25mm dia including conduit accessories and connecting terminal ends to DB's including providing 1 run of 6 sq.mm PVC insulated unsheathed multistranded FRLS grade copper cable as earth continuity conductor and connecting to common earth dolly, complete all as specified and directed. NOTE:- (i) Two runs of 6 sq.mm copper conductor, one run of 6 sq.mm copper earth continuity conductor and one run of PVC conduit and conduit accessories shall be measured as one unit length. (ii) Extra length of cable / wire required for connection to MCBs shall not be measured and the rate quoted per unit shall deemed to be inclusive of the same accordingly.
Ceiling rose three terminal PVC / polycarbonate insulated body, surface bakelite type AC 50 Hz 230V, in repair complete all as specified and directed.
Lamp holder, PVC polycarbonate body with back plate suitable for batten fittings, in repair complete all as specified and directed.
Modular switch 6 Amp, one-way, one module, 240V, in repairs complete all as specified and directed. MAKE:- Havells / L&T / Legrand
Modular Bell push 6 Amp, one module, 240V, in repairs complete all as specified and directed. MAKE:- Havells / L&T / Legrand
Modular socket outlet, 3-pin, 6 Amp, flush type, 240V, in repairs complete all as specified and directed. MAKE:- Havells / L&T / Legrand
Modular switch 15 Amp, one-way, one module, 240V, flush type, in repairs, complete all as specified and directed. MAKE:- Havells / L&T / Legrand
Modular Socket outlet, 2 in 1, 3 pin, 15 Amps 240 Volts, flush type, in repair, complete all as specified and directed. MAKE:- Havells / L&T / Legrand
Modular type Stepped type electronic fan regulator flush type duly fixed on the existing phenolic laminated sheet etc. as required, 240V, humming free, 2 module, ISI marked, in repairs complete all as specified and directed. MAKE:- Havells / Plaza / SSK / Anchor
Modular cover plate with grid frames, 2-module, flush type, in repairs, complete all as specified and directed.
Modular cover plate with grid frames, 4-module, flush type, in repairs, complete all as specified and directed.
Modular cover plate with grid frames, 6-module, flush type, in repairs, complete all as specified and directed.
Modular cover plate with grid frames, 8-module, flush type, in repairs, complete all as specified and directed.
LED lamp 9W, suitable for lamp holder, in repairs, complete all as specified and directed.
Recess mounted decorative LED downlight fittings of 6 Watt 6000K Lumen white powder coated pressed die cast aluminium housing with high efficiency reflector and spring mounting brackets 6500 K lumen efficiency, high brightness including suitable driver poly carbonate body, envoirement friendly, energy efficient pre-wired and making necessary electric connection from ceiling rose with 23/.0076 flexible copper wire three core, in repairs, complete all as specified & directed. Make : Havells Cat Part No EDGEPRORDDLR6WLED840S or techno-commercially equivalent model in Philips / Crompton / Bajaj as approved by GE
Suspended architectural LED luminaire soft light glare free symmetrical illumination (with continuous mounting caps) includng suspended conduit of suitable size for 40W LED high lumen efficiency including suitable driver, environmental friendly, energy efficient complete with all accessories, prewired and making conection with and including 23/0.0076 flexible copper wire three core from connector to ceiling rose not more than 1.2mtr, fixed on wall firmly, in repair, complete all as specified and directed. Make: Havells Cat part No. CONSTA1144LP40WLED830SPCWH or techno-commercially equivalent model in Philips/ Crompton as approved by GE.
LED tube light fittings 1x20 watt four feet long decorative box type [Ultra slim] linear LED [6000K] with co-extruded polycorbonate body, envoirement friendly, energy efficient prewired and making conection with and including 23/0.0076 flexible copper wire three core from connector to ceiling rose not more than 1.2mtr, fixed on wall firmly, in repair, complete all as specified and directed.. Make : Havells E Lite Pride Plus Cat Part No LUMILINEPLUSBS20WLED865SPCSS or techno-commercially equivalent model in Philips/ Bajaj/ Crompton as approved by GE.
Aesthetically desigend LED mirror light fitting 1x10 watt LED 6500K, decorative, provided with high output PMMA diffuser for glare free light, with co-extruded polycarbonate body, envoirement friendly, energy efficient pre-wired and making necessary electric connection from ceiling rose with 23/.0076 flexible three core copper wire or fixed to wall firmly, in repairs, complete as specified & directed. Make : Crompton Model LINNET Cart part No. LCL-10-CDL or techno-commercially equivalent model in Bajaj or Philips as approved by GE.
Recess mounted decorative CRCA LED light fittings of size 600 mm x 600 mm, 36 Watt LED 6500 K lumen efficiency, high brightness SMD leds, including suitable driver poly carbonate body, envoirement friendly, energy efficient pre-wired and making necessary electric connection from ceiling rose with flexible copper wire, in repairs, complete all as specified & directed. Make : Havells Cat Part No VENUSNEOHE2X2R36WLED840PIRSENSOR or techno-commercially equivalent model in Bajaj or Philips as approved by GE.
Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 16 to 32 Amp 240V, in repair, complete all as specified and directed. MAKE:- Legrand / Havells / L&T / ABB
Exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers, including making hole in wall, complete all as specified and directed.
Spreading of natural, clean and dry river sand in trenches for cable cushioning, including punning the sand upto desired thicknes and consolidated, complete all as specified and directed. NOTE: Punned thickness shall only be measured and paid.
Supply and lay burnt clay fly ash bricks class 'B', modular bricks, laid in trenches for cable protection with length of brick equal to width of trench, complete all as specified and directed.
Supply, laying and testing XLPE cable insulated, screened, PVC beded galvanised steel strip or wire armoured, electric power cable (Heavy Duty) 1100 Volt grade with stranded aluminium conductor of 2.0 core 16 sq.mm, complete all as specified and directed. NOTE:- Excavation, earth work, sand cushioning and brick protection work shall be measured and paid separately under respective items of this Schedule. MAKE:- Havells / Nicco / Kalinga premium / Universal
Supply, laying and testing XLPE cable insulated, screened, PVC beded galvanised steel strip or wire armoured, electric power cable (Heavy Duty) 1100 Volt grade with stranded aluminium conductor of 2.0 core 6 sq.mm, including taking down existing old/ unserviceable cable, complete all as specified and directed. NOTE:- Excavation, earth work, sand cushioning and brick protection work shall be measured and paid separately under respective items of this Schedule. MAKE:- Havells / Nicco / Kalinga premium / Universal
Supply, laying and testing XLPE cable insulated, screened, PVC beded galvanised steel strip or wire armoured, electric power cable (Heavy Duty) 1100 Volt grade with stranded aluminium conductor of 3.5 core 25 sq.mm, including taking down existing old/ unserviceable cable, complete all as specified and directed. NOTE:- Excavation, earth work, sand cushioning and brick protection work shall be measured and paid separately under respective items of this Schedule. MAKE:- Havells / Nicco / Kalinga premium / Universal
LED bollard light 8W cone NXG series, innovative design with uniformly lit diffuser at the upper portion acting as a beacon of path guidance in a landscape environment, in repairs complete all as specified and directed. Make: Havells Cat Part No CONENXGBLS8WLED857PSYMTOPCM (1.0M) or techno-commercially equivalent model in Philips/ Bajaj/ Crompton as approved by GE.
GI pipes, light grade, ISI marked, galvanised including short lengths, laid in trenches / fixed to walls / ceilings or laid in floors / laid in ducts / laid under road crossing for cables, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 40mm bore of pipe, including taking down of pipe, complete all as specified and directed. NOTE:- Necessary excavation and earthwork for GI pipe shall be measured and paid separately under respective items of this Schedule.
LED street light 80Watt energy saving and environment friendly long life 230V, AC outdoor type with high pressure die cast aluminium hosting and deat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection including bracket duly painted with synthetic aluminum paint over a coat of primer MS clamps and back plates fabricated from steel section including nuts and bolt to be fixed on wall/pole, in repair complete all as specified and directed. Make: Havells Cat Part No ENDURACITYLINERNEOMPSL80WLED757PASYBOTG or techno-commercially equivalent model in Philips & Ecolink/ Crompton as approved by GE.
Sheet metal enclosure for MCCB DBs TPN, 4 way, double door, IP-43, vertical type, 415 V with 200 Amps rated bus bar, complete with incoming/ outgoing connection through proper size of lugs and cable glands and with space for placing 4 pole MCCB as incomer and SP/TP MCB's as outgoing, in repair complete all as specified and directed. Make: L&T Cat Part No. DBVTL004SD/ Legrand/ Schneider.
MCCB TPN 100 Amp, 415 V, 10 kA thermal release range, in repair, complete all as specified and directed. Make: Legrand/ Schneider/ ABB/ L&T/ Indo Asian
Sheet metal enclosure for MCB DBs SPN, 8 way, double door, vertical type, 240 V with 200 Amps rated bus bar, complete with incoming/ outgoing connection through proper size of lugs and cable glands, in repair, complete all as specified and directed. Make: Legrand/ Schneider/ ABB/ L&T/ Indo Asian
MCB SPN 6-32 Amp, 240 volts 10 KA, 'C series' in repair complete all as specified and directed. Make: Legrand/ Schneider/ ABB/ L&T/GE (Power)
MCB SP 6-32 amps 230 Volts, 10 KA 'C series' in repair complete all as specified and directed. Make: Legrand/ Schneider/ ABB/ L&T/GE (Power)
Switch piano, flush type single pole, one way 5/6 Amp 240 volts, white or ivory, ISI marked, in repair, complete all as specified and directed.
Socket outlet, 2 in 1, 5 pin, 5/6 Amps 240 Volts, flush type, in repair, complete all as specified and directed.
Switch piano, single pole, one way 15 Amp 240 volts, ISI marked, in repair, complete all as specified and directed.
Socket outlet, 2 in 1, 6 pin, 15 Amps 240 Volts, flush type, in repairs, complete all as specified and directed.
Stepped type electronic fan regulator flush type duly fixed on the existing phenolic laminated sheet etc. as required, 240V, humming free, 2 module, ISI marked, in repairs complete all as specified and directed. MAKE:- Havells / Plaza / SSK / Anchor
LED mirror light fitting 1 x 10 watt, LED 6000 K decorative , indirect up down LED lighting fixture with co extruded polycarbonate body , environmental friendly , energy efficient complete with all accessories, prewired and making connection with and including 23/0.0076 flexible copper wire two core from connector to ceiling rose not more than 1.2 mtr, fixed on wall firmly, in repair, complete all as specified and directed.
LED bulk head light fittings 1x10 watt having 600 Lumen enclosed in polycarbonate body, weather proof with co-extruded poly carbonate body, envoirement friendly, energy efficient pre-wired and making necessary electric connection from ceiling rose with flexible copper wire or fixed to wall firmly, in repairs, complete all as specified & directed. Make : Havell's Cat Part No. HEXAFT10WLED857SSYMBOPC / Bajaj Model Wee Plus Cat Part No. BIBWP10LED or techno-commercially equivalent model in Crompton or Philips as approved by GE.
LED wall mounted tube light fittings 1x18 watt four feet long decorative box type [Ultra slim] linear LED [6000K] with co-extruded polycorbonate body, envoirement friendly, energy efficient prewired and making conection with and including 23/0.0076 flexible copper wire three core from connector to ceiling rose not more than 1.2mtr, fixed on wall firmly, in repair, complete all as specified and directed..
Road lighting luminaire 36W with unique peanut optics to ensure uniform distribution, hgiher spacing between poles and maintenance free system for city roads and streets, 50% energy saving, IP 66 protection PC and FG cover, high impact resistance complete including LED lamps and all accessories including bracket made out of 25mm bore light grade GI tubing of 1.20metre length bent to shape required and fixed to existing pole or building by means of two Nos MS FI 40mmx6mm clamps with suitable size bolt, nuts and washers and making connection with and including provision of three core flexible copper cable of size 23/0.0076 from fittinge to existing junction boxr of required length, in repair, complete all as specified and directed. MAKE:- Cat No. BRP409 LED CW 036 MR FG S1 PSU GR of Philips or Cat No ENDURACITYLITEPLATPLUSSL36WLED757SASYBOPC of Havells or techno-commercially equivalent model in Bajaj / CG
LED smartbright spotlight fitting, 14W, LED 100 lm/W, aluminium housing 5000K, LED lighting fixture with co extruded polycarbonate body , environmental friendly , energy efficient complete with all accessories, prewired and making connection with and including 23/0.0076 flexible copper wire two core from connector to ceiling rose not more than 1.2 mtr, fixed on wall firmly, in repair, complete all as specified and directed.
Earthing complete with GI earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth of not less than 2.25m deep below ground level with the top edge of earth plate at a depth of not less than 1.5m below ground level connected to GI earth lead of 4mm dia by means of bolts, nuts, washers of galvanised iron or steel, GI earth wire shall be protected by 15mm dia GI pipe 'medium grade', GI wire meshed funnel, alternate layer of charcoal and salt on all side to earth plate upto a thickness of 150mm, filling of black cotton soil in earth pit upto GL and connected to earth plate including necessary excavation & earthwork, PCC (1:2:4) type B-1 earth chamber and mild steel angle iron frame 25 x 25 x 6 mm and 40mm thick pre-cast RCC cover (1:2:4), type B-1 (using 20mm graded crushed aggregate) mix with 6mm dia MS bars @75mm c/c both ways, mild steel handle 12mm dia, PGI funnel and wire mesh, 20mm dia GI pipe light grade(ISI marked) for watering, etc complete all as shown in electrical plate No.5 of SSR Part-1, connected to earthing test point, including testing on completion, complete all as speciifed and as directed. NOTE:- The quoted rates shall also deemed to include the cost of Earth Test point and earth wire and protection pipe upto 7.5 metre beyond the earth plates electrode.
Sub main wiring complete with 2 runs of 4 sq.mm PVC insulated and unsheathed 1100V grade multistranded FRLS grade copper conductor cable drawn through and including provision of PVC rigid conduit 20mm dia and accessories connecting terminal ends to DB's including providing 1 run of 4 sq.mm PVC insulated unsheathed multistranded FRLS grade copper cable as earth continuity conductor and connecting to common earth dolly including taking down existing sub main wiring any type and making good disturbed surfaces to match with existing including sinking of boxes , complete all as specified and directed. NOTE:- (i) Two runs of 4 sq.mm copper conductor, one run of 4 sq.mm copper earth continuity conductor and one run of PVC rigid conduit and with accessories shall be measured as one unit length. (ii) Extra length of cable / wire required for connection to MCBs shall not be measured and the rate quoted per unit shall deemed to be inclusive of the same accordingly.
Ceiling fan (5 star rating), 1200mm sweep, copper wound motor suitable for 230V AC supply, with and including fan regulator, PVC canopy, 15 mm dia 300mm long hanging rod, device with rubber real and split pins and making necessary connection with ceiling rose with twin core copper wire of suitable size, in repair, complete all as specified and directed.
Supply, installation, testing of window type air conditioner electric driven (single phase) complete with cordless remote control unit and with in-built cooling arrangement and digital inverter rotary type compressor, single phase units 220V- 240V, 50Hz, inbuilt stabilizer complete with 5 star rating and EER 3.2 of 1.5 TR capacity, including taking down the existing AC 1.5 TR capacity from the position, making good surface, as per existing each AC unit deposited to E/M store yard complete all as speciifed and directed.
Supply, installation, testing of Hi wall split type air conditioner units indoor/ outdoor complete with cordless remote control unit and with in-built cooling arrangement and digital inverter rotary type compressor, single phase units 220V- 240V, 50Hz, inbuilt stabilizer complete with 5 star rating and EER 3.2 of 1.5 TR capacity, including taking down the existing AC 1.5 TR capacity from the position, making good surface, as per existing each AC unit deposited to E/M store yard complete all as speciifed and directed.
Supply, installation, testing of water cooler, stainless steel body with tank and single tap, electric driven (single phase) having approximate capacity of 120 litre and normal cooling capacity of 60 litre per hour, alongwith provision of suitable accessories as required for sucessful working of cooler, complete all as specified and directed. MAKE:- Voltas / Bluestar
Supply, installation, testing of refrigerator, double door of capacity 280 to 310 ltrs, BEE 4/5 star rated, and with in-built stabilizer, complete all as specified and directed.
Supply, installation, testing of desert cooler, electric driven (single phase) with kit fan motor 450mm sweep, made out of PGI sheet 1mm thick of size not less than 0.5 width and 0.7m height and storage tank of PGI sheet 1mm thick of size not less than 0.7m x 0.7m and height 0.2m, having approximate normal air flow of 5000 cu.m per hour, alongwith provision of suitable accessories as required for sucessful working of cooler, complete all as specified and directed.
Mohit Enterprises
Bharat Trading Company
ms shanti sons
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .