Widening and Strengthening of Ayodhya Uttraula Sultanpur Pryagraj Road SH 09

Excavation for trench of roadway in soil using manual means including loading in truck for carrying of cut earth to embankment site with all lifts and lead upto1000 metres.as per clause 301(3.1)

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5m , transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300.2

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5m , transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300.2 With Cartage

Construction of subgrade with earthen soulders with approved material obtained from borrow pits with a lift upto 1.5m , transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300.2

Construction of subgrade with earthen soulders with approved material obtained from borrow pits with a lift upto 1.5m , transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300.2 With Cartage

Construction of Subgrade and earthen soulder,s deposited from roadway (Compaction only)

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with grader in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

Providing and laying dence graded bituminous macadam with 100-120 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder@ 4.0 to 4.5% by weight of total mix and filler, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per morth specification clause 507 complete in all respects.

Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects.

Providing and applying tack coat with bitumen using bitumen pressure distributor at the rate of 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects

Providing and fixing of informatory sign board of MS plates of 1.6mm thick size 1200 x 900 duly welded on angle iron frame 45x45x5 with cross legged flat iron of 35x6mm duly welded for gross support of vertical angle iron post of 3 meter height. Lower end of vertical support will be welded to 2 No 75x75mm of SWG sheet duly embedded in cement concrete in M-15 grade blocks of 450x450x600mm, 600mm below ground level. All MS will be stove enameled on both sides, Lattering and Printing arrows, boarder etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and Plates will be painted with primer and two coats of epoxy as per drawing clause-1701 and Annexure 1700.1.

Providing and laying of KM stone of standard design as per IRC-8 fixing in position including painting of KM stone with 2 coats of approved synthetic enamel paint and lettering as per PWD maintenance manual including cost of KM stone, transpotation to site and all materials labour T&P etc. required proper complete of Work.

Providing and laying of Hecto Meter stone of standard design as per IRC-8 fixing in position including painting of KM stone with 2 coats of approved synthetic enamel paint and lettering as per PWD maintenance manual including cost of KM stone, transpotation to site and all materials labour T&P etc. required proper complete of Work.

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including retroreflactive glass beads@ 250 gms per sqm area thickness of 2.5 mm is exlusive of suface applied glass beads as per IRC:35 the finished surface to be level uniform and free form streak and holes MORTH 803 (8.13).

Direction of place indentification sign with size more than 0.90 sqm size board providing and erecting direction place identification reflactoirised sign as per IRC 67 made high intensity grade shieeting wide clause 801.3 fixing over aluminium sheeting 2mm thick area exceeding 0.9 sqm supported on a mild steel angle iron post 75mm MORTH 801(8.6).

Providing and fixing of retero reflacting delinator post IZ-ASTMAD-456-4 Made of 75 mm dia round of 1.2 m high with fixing support

Thermoplastic Repeted Bar marking is a softer treatment to reduce the speed. One set of bar marking (refer TM 08) comprises of 6 bars of 300 mm wide. Each strip of thermoplastic strip shall be of 5 mm high and shall be set applied across the full width of the carriageway. MORT&H 803

Providing and fixing of retro relectorised cautionary, mandatory and infrormatory sign as per IRC :67-212 made of high intersity grade sheeting vide cluse 801.3 friced over aluminium sheeting type-IV 1.5 mm thick supproted on a mild steel angle iron post 75mmx75mmx6 mm firmly fixed to the gournd by means of propertly designed foundation with M 15 grade cement concrete 45 cm x 45 cm x60 cm, 60 cm below ground level as per approved drawing. The retro reflective sheeting shall be tested for 3 year outdoor weathering test in indian conditions as per IRC 37:2012 as per MORTH 801(8.4) (VIII) 50x60 cm single chevron)

Supply and fixing of Pevement marker (Cate Eye) type X-ASTMD-456-4 avery

W metal beam MORTH 810(8.23).

Earth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam clay or sand) including lift upto 1.5 m. lead upto 50m and dressing of sides and rammings of bottom and disposal of surplus exdavated earth as directed by the Engineer I/C within a lead of 30 m as per MORD 300.

Providing and laying Cement Concrete 1:4:8(1 cement :4sand : 8 graded stone aggregate 40 mm nominal size) including supply of all materials, labour and T&P etc. required for proper completion of work and curing complete, also including cost of formwork in foundation and floors as per SI no.275

Class- 150 brick work in 1:3 cement and coarsesand of 2.8 fineness modulus mortar in foundation and plinth including supply of all materials labour and ltools and p;ants etc. required for proper completion of the work.SI no 307.

R.C.C. work cement approved coarse sand, and 2 Cm. (3/4") gauge approved stone ballast in the proportion 1:1.5:3 in lintels of doors and windows, excluding supply of reinforeement and its bending but including its fixing and binding the same with 24 B.W.G.G.I. binding wire and including neaessary centering and shuttering etc. and also including supply of all materials labour and tools and plants etc. required for proper completion of the work binding wire to be supplied by the contractor free of cost for: SI no 288.

Mild steel or iron in plain work such as in reinforced concrete / brick work (when not included in overall rates) wrought to required shape as necessary I/C bending for proper completion of the work and including supply of steel, it's wastage and hooks and authorized over lapping shall be measured. SI no 504(b).

Routine Maintenance of road after completion of work :- (A) Carriageway/ Pavement: (a) Potholes, cracks, other surface defects (SWMM & BC), (b) Repair of Edges, Rutting (BC) (B) Road, Embankment, Cutings, Shoulders, Trees & Plantation : (a) Road Maintained free of edge drop, inadequate cross fall, undulations, settlement, Ponding (E/W), (b) Deficent slopes, rain cuts in embankments (E/W), Vegetation growth, Loping of tree branches. (C) Bridges and Culverts: (a) De-Silting, (b) Clearing vegetation growth (Jungle Clearance), (c) Damaged/distrubed boulder pitching, breast/toe wall retaining wall, apron flooring, guide bunds (Boulder Apron), (d) Parapet, any damage to foundations, (e) Any defects in sub-strucures, (f) Any defects in superstructures, raillings, parapets. (g) Wearing coat, (h) Approach slab, (i) Painting & Lettering of No. plates, repair. (D) Repair of Roadside Drains: (a) Brick Work in 1:4, (b) Plaster, (c) CC- 1:2:4. (E) Road Furniture: (a) Cleaning, Painting & lettering of stones & sign boards, Replacement of damaged/ missing stone & sign boards. (b) 200 m Stones, (c) Km stones, (d) 5th km stones. Maintenance requriment as per above and Mentioned in Special Condition of Contract for Maintenance. Payment of Maintenance work as Percentage of final Civil Construction Cost :

a) For Ist Year @ 0.00%

b) For IInd Year @ 0.25%

c) For IIIrd Year @ 0.50%

d) For IVth Year @ 0.75%

e) For Vth Year @ 1.00%

Please Enable Macros to View BoQ information