CWE/K-T35/2019-20 SPECIAL REPAIR TO BLDG NO. T-151 AND T-246 AT NIMU UNDER AGE (I) NIMU

Amount

Demolition of plain cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thick (below or above ground level), complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L non-skid coloured ceramic tiles, 7mm to 8mm thick (Square / rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match the shade of tile, over & including 15mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge.

M & L for glazed ceramic coloured tiles of size 300mm x 200mm x 6mm thick as on vertical surfaces such as wall, skirting, dado etc, set and jointed in neat cement slurry and pointed in white cement with pigment or coloured cement to match the shade of tile over & including 10mm thick rendering/backing coat plaster in cement mortar 1:3, complete all as specified and directed by Engineer-in-Charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards / slabs / blankets, any thickness, including cover fillets, complete all as specified & directed by Engineer-in-Charge.

Dismantling of timber scantling as in fillet, rails, posts, rafters, purlins etc. under 40 sqcm in section in any position as in unframed work complete all as specified & directed by Engineer-in-Charge.

M&L for 9mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nails to timber frame work as in wall, complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class soft wood, plain fillets, square, rectangular or triangular in section of area exceeding 13 sqcm but not exceeding 25 sqcm, clean sawn, secured with nails or brads, complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class soft wood beading, in section of area exceeding 3 sqcm but not exceeding 6 sqcm, bull-nosed, splayed, chamfered or rounded on one edge or face, complete all as specified and directed by Engineer-in-Charge.

S & F 6mm thick plywood, grade BWR, type BB, fixed with nails to timber frame work in ceiling, complete all as specified and directed.

Fixing only plywood, fixed with nails to timber frame work.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

M&L for precast cement concrete, type C-1, 1:3:6 (using 20mm graded mechanically crushed stone aggregate) block masonry with solid blocks, exc. 10cm in width and set in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge.

M&L 15mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

M&L 10mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Taking down plastering on brick or concrete surfaces etc incl racking out joints, hacking for key, scrubbing down with water, etc built in cement mortar all as specified.

Preparation of newly plastered or unplastered surface and applying three coats of white wash on walls, complete all as specified.

Preparation of newly plastered or unplastered surface and applying two coats cement base paint complete all as specified.

Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutters from the frames), complete all as specified and directed.

Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutters from the frames), complete all as specified and directed.

S&F 2nd class soft wood, Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F 35 mm thick, 2nd class soft wood, plain framed, panelled shutter (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied & fitted to chowkhats complete all as specified and directed by Engineer-in-Charge.

S&F 30mm thick, 2nd class (kail) soft wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc.(without sash bars) divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers as in windows, ventilators, etc. & provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(a) complete all as specified and directed by Engineer-in-Charge.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed by Engineer-in-Charge.

S&F 250mm long, aluminium alloy, anodised, sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

S&F 150mm long, (ISI Marked) aluminium anodised, barrel tower bolt of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 100mm long, (ISI Marked) aluminium anodised, barrel tower bolt of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 100mm long (ISI Marked), mild steel, butt hinges, medium weight, cold rolled, complete all as specified and directed by Engineer-in-Charge.

S&F 75mm long (ISI Marked), mild steel, butt hinges, medium weight, cold rolled, complete all as specified and directed by Engineer-in-Charge.

S&F 150mm size (ISI Marked), extruded aluminium alloy handles, fabricated type 'D', anodised complete all as specified and directed by Engineer-in Charge.

S&F 100mm size (ISI Marked), extruded aluminium alloy handles, fabricated type 'D', anodised complete all as specified and directed by Engineer-in Charge.

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

Demolition of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed by Engineer-in-Charge.

S&F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type hook bolts in liue of screws and washers, in roofs, walls etc. with grade of zinc coating 275, complete all as specified and directed.

S&F Plain galvanised mild steel sheeting 0.63mm thick, with 275 micron thick galvanising as in ridges, valley gutters etc. (length and girth as fixed), complete all as specified and directed.

M&L One coat of synthetic enamel paint on old steel surfaces of any description over 10 cm width or girth incl prepration of surfaces including filling with filler where required, complete all as specified and directed.

M&L two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description, over 10cm width or girth incl prepration of surfaces including filling with filler where required, complete all as specified and directed.

M&L two coats of synthetic enamel paint over a coat of pink primer on new wooden based surfaces of any description, over 10cm width or girth incl prepration of surfaces including filling with filler where required, complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for including rubbish off the premises, complete, all as specified and directed.

M&L for cement concrete type C-2 1:3:6, (40mm graded crushed stone aggregates) 75mm thick as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

S&F of 3 layer PP-R poly propylene reandom copolymer concealed pipes of outer dia 16mm SDR 7.4 (PN-16) UV stablized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threated polypropylene random fittings fixed complete to walls, ceilings or floors etc.

S&F of 3 layer PP-R poly propylene reandom copolymer concealed pipes of outer dia 20mm SDR 7.4 (PN-16) UV stablized and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threated polypropylene random fittings fixed complete to walls, ceilings or floors etc.

S&F in repair 15mm bore stop/angle valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs hand shower (health faucet), brass body with 8mm dia and 1 meter long SS braided flexible tube and wall hook, complete all as specified and directed by Engineer-in-Charge. Make:- Jaquar cat part No. 573 or equivalent of Orient/Parko/ Riviera/ Gem

S&F in repair Vitreous china wash down water closet pan "Pedestal Pattern" white, with seat white closed pattern with flat bottom and cover mild steel chromium plated or aluminized hinging deviced including flush pipe and joint etc and connection to drain, flushing, pipe, anti-syphonage pipe, and fixing arrangements with fixing bolts etc including making good the disturbed portion of floor in cement concrete 1:2:4 type B-0, complete all as specified and directed by Engineer-in-Charge.

S&F in repair Vitreous china wash hand basin, white/colour, flat back or angle back of size 550mm x 400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, chromium plated complete and including cutting for and pinning in ends of brackets or erecting stand, complete all as specified and directed by Engineer-in-Charge.

S&F of waste coupling of PTMT (Half or full threaded). (Minimum wt 32mm-45gms/40mm-60gms) including flexible wate pipe, complete all as specified and directed.

S&F in repair 15mm bore pillar tap, cast copper alloy, chromium plated fancy type with crutch or butter fly handle, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed by Engineer-in-Charge.

S&F in repair bib taps, cast copper alloy, chromum plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule for 15mm bore pipes complete all as specified & directed.

S&F PVC connections 15mm size with PTMT nuts of length 450 mm, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs soap dish/tray, vitreous china white approximate size 160x160x90mm embedded in the wall etc complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank three layered of 500 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in repair in position all as specified in SSR complete all as directed at site.

S & F 4mm thick plywood, 3 no of ply, grade BWR, type BB, fixed with nails to timber frame work in ceiling, complete all as specified and directed.

S&F 300mm long, aluminium alloy, anodised, sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

S&F 25mm dia MS drapery rod, teak wood finish, good quality, including wooden finish PVC brackets for holding of curtain rod and end knobs of matching colour complete all as specified and directed by Engineer-in-Charge. Note: A set of 2 Nos bracket and 2 Nos Knob shall be provided at every 1.5 to 2.0 mtr length (on average basis) of drapery rod as directed by Engineer-in-Charge.

S&F floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 150mm, fixed in floor complete all as specified and directed by Engineer-in-Charge.

All as per item No. 34 above but exceept sheets using serviceable sheets retived from demolition.

M&L two coats of synthetic enamel paint over a coat of pink primer on new wooden based surfaces of any description, over 10cm width or girth, complete all as specified and directed.

Wind ties (FI 40x5mm) for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge.

Taking down carefully copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants, regulators, sockets light fitting etc for taking credit removing from site and making good disturbed surface etc complete all as specified and directed.

M&L for point wiring with PVC insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed for One light point controlled by one switch.

All as per item no. 64 but One 3 pin 5 amps socket on same board.

All as per item no. 64 but One 3 pin 5 amps socket outlet independent with cables 1.5 sqmm size.

All same as per item No 64 here-in-before but with conductor of size 2.5 sqmm (Nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 2.5 sqmm PVC insulated stranded copper conductor cable complete all as specified and directed.

M&L for switch piano flush type 5 Amp, single pole, one way complete all as specified and directed.

M&L for switch piano flush type 15 Amp, single pole, one way complete all as specified and directed.

S&F Socket outlet 2 in 1, 3 pin, 5 amp and 15 amp flush type, complete all as specified and directed.

S&F Socket outlet 2 in 1, 3 pin, 5 amp flush type, complete all as specified and directed.

S&F in replacement sheet metal enclosure for DBs when MCBs to be used single pole and neutral 8 way, complete all as specified and directed.

S&F in replacement MCB SPN 32 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards, complete all as specified and as directed.

S&F in replacement MCB SP 6-32 Amp with 10KA breaking capacity of 'C' series in distribution boards complete all as specified and as directed.

S&F wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver 18 W Led 4 K complete all as specified and directed by Engr-in-Charge.

Material and labour for sub main wiring with 2 x4 sqmm + 1 x 2.5 sqmm as earth wire PVC insulated stranded copper conductor including non metallic rigid PVC casing caping duly ISI marked, fixed on wall ceiling with GI screws, rawal plugs (Surface wiring) with all fittings incl taking down old unserviceable wiring.

S&F for ceiling rose surface bakelite 65x 50 mm two to three terminals all as specified and as directed by Engr-in-Charge.

Supply and install 45 watt energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP66 roadway luminaire with high power LED as light source and electronic driver including brackets and clamps luminaries, complete all as specified and as directed. Make Havells/Philips/Wipro

S&F 2 x2 feet LED fitting light 28 watt suitable for armstrong/ grid ceiling complete all as specified and directed by Engr-in-Charge. Make Havells/Philips/Wipro

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 Mtr below ground level) with top edge of earth plate not less than 1.5Mtr below ground level connected to galvanized earth strip 25x4mm ( incl upto 7.5mtr) as earthing lead by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber) 1:2:4 type B-1 using 20mm graded stone aggregate copy shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate, internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4 funnel wiht wire gauge of 22 gauge (0.68mm) 8 mesh per liner inch, 50mm thick cover of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with 8mm four MS bars @ 80mm centre to centre both ways and charcoal dust and common salt all as shown in electrical plate No 5 of MES SSR Part-I (1991) and specified including provision of earth wire protected by 40mm dia medium grade pipe and watering pipe shall be 25mm bore medium grade, all excavation and earth work & connectiing the earthing to an earthing test point as specified and testing on complete all as specified & directed by Engr-in-Charge.

Material and labour for sub main wiring with 2 x4 sqmm + 1 x 4 sqmm as earth wire PVC insulated stranded copper conductor including non metallic rigid PVC casing caping duly ISI marked not less than 20mm dia, fixed on wall ceiling with GI saddles, GI screws, rawal plugs (concealed conduit wiring) with all fittings incl taking down old unserviceable wiring.

S&F in replacement of LED luminaries light fitting single tube 1 x 20 watt, 4 feet long, with bipin holders with all accessories including LED tube rod 20W , internally pre-wired and including connecting electrically with 3 core PVC insulated sheathed flexible copper conductor cable to ceiling rose all as specified. Make: TARA-M/20W C&S equivalent make DMLN1LT8-16 (for frame/batten), LTT8-20(for rod) Crompton/ D622065 (for rod) and P08120 (for frame) 0f Wipro/ LHEXCEP7UN1W020 (for rod) & LHFXCEP1TN1W020 (for frame/batten) of Havells/ Polycab, complete all as specified & directed.

S&F CFL light fitting, 1x9 watt, bulk head luminaries, with lamp holders, etc. complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50 HZ, incl taking down old, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs office hanging light, suspended type, having dome shaped refractor optics luminaire with bottom refractor cover suitable for 25W/26W CFL, including pulling system/ suspension system with PVC rounded wire, with 25W CFL confirming to cat part No. TRF25 of CG or BLRI 126 CFL WEB1 of Bajaj or FPK550 1xPLC26W EBW PR of Philips or as approved by Engineer-in-charge.

S&F in replacement sheet metal powder coated versatile double door TPN distribution board fitted with two cover with copper bus bar rated 200 amps, neutral link, earth bar and din rail suitable for use on 415 Volts, 50 Hz supply 4 way complete all as specified and as directed.

S&F in replacement sheet metal powder coated versatile single door SPN distribution board fitted with two cover with copper bus bar rated 200 amps, neutral link, earth bar and din rail suitable for use on 240 Volts, 50 Hz supply 8 way complete all as specified and as directed.

S&F in replacement MCB TPN 63 Amp, 415V with 10KA breaking capacity of 'C' series in distribution boards, complete all as specified and as directed.

S&F in replacement MCB SPN 63 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards, complete all as specified and as directed.

S&F in replacement MCB SPN 40 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards, complete all as specified and as directed.

Dedcuct Credit for Demolished/Dismantled material Rs (-) 83925.00 (Minus) as listed in Schedule 'A' Part-II (Credit Schedule) Note : Tenderers will not quote against this item being a tentative amount, to be considered to arrive at the 'Contract Sum'.

SASPOL LARJAY CONSTRUCTION

M/S SHAMSHER ALI SUFI

tamchos gurmet

M/S MA CONSTRUCTION Co

M/S LEO TRADERS

M/S LIBE & CO